SPECIAL REPAIRS TO BLDG NO P 7 ORS MD ACCN 09 QTRS UNDER GE MH AND RH KIRKEE

Amount

Dismantling floor, hearth or wall tiling including cement mortar bedding/complete and removing serviceable tiles & rubbish off the premises complete all as specified and directed.

M&L Coloured Non Skid ceramic tiles 7 to 8mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with the tile laid over and including 15 mm thick screed bed or bedding layer in CM 1:4 all as directed.

Ditto all as in item No.2 above but as in skirting /dados in CM 1:4 etc complete, all as specified and directed.

M&L Coloured ceramic tiles 450X300X7 mm thick, on vertical surfaces such as skirting, dados etc., set and jointed in neat cement slurry and pointed in white or Coloured cement to match on 10 mm thick rendering as in backing coat in CM 1:4 complete, all as specified and directed.

M&L non-skid ceramic coloured tiles 7 to 8 mm thick (square/rectangular) area of each tiles exc 0.06 sqm but not exc 0.11 sqm in floor etc set and jointed in neat cement slurry to match the work using colour tiles over and including screed bed on bedding layer 15mm thick in CM 1:4 as in floors all as specified and directed.

Taking down cement plaster in any description incl racking out joints hacking for key and scrubbing down with water etc removing rubbish out side the premises complete all as specified and directed by Engineer-in-charge

M&L rendering 15 mm thick (10mm + 5mm) plaster on fair face of brick work in CM 1:4 and surface finished even and fair by mixing liquid water proofing compound as per manufacturers instructions complete. Note :- Liquid WPC shall be measured & paid seprately under relevant item of this BOQ.

M&L for preparation newly plastered surfaces of walls/ceilings and applying two coats of weather proof acrylic exerior paint (100%) Acrylic) over one coat of self primer including scaffolding, trestles, ladders, cradles and necessary safety measures complete all as specified.

M&L for complete removal of existing treatment, preparing the surfaces walls /ceilings and applying two coats of weather proof acrylic exerior paint (100%) Acrylic) including scaffolding, trestles, ladders, cradles and necessary safety measures complete all as specified.

M&L rendering 10mm thick in CM 1:4 finished even & smooth without using extra cement as in ceiling complete all as specified and directed

M&L for applying three coats of white wash on ceiling surfaces including preparation of newly plastered surfaces complete all as specified & directed.

M & L for applying one coat of white wash on Ceiling on old surfaces including preparation of old surfaces all as specified and directed.

M & L for 15 mm thick rendering in cement mortar 1:6 on fair faces of brick work or concrete surfaces including finishing the surface with a coat of sagol not less than 1 mm thick complete all as specified and directed.

M & L for preparation of newly plastered surfaces of wall and applying two coats of oil bound distemper over a coat of alkali resistant primer over wall care puty not less than 1mm thick complete all as specified and directed

.M&L for complete removal of existing finishes and applying two coats of oil bound distemper over a coat of alkali resistant primer over wall care puty not less than 1mm thick including preparation of surfaces of wall complete all as specified and directed

M&L for preparation of new plastered surface of walls and applying three coats of white wash complete all as specified and directed.

M& L for complete removal of existing finishes and applying three coats of white wash on walls including preparation of surfaces all as specified and directed.

M & L for preparation of old wooden surfaces exc 10 cm width or girth and applying one coats of synthetic enameled paint complete all as specified.

M & L for preparation of old steel surfaces exc 10 cm width or girth and applying one coats of synthetic enameled paint complete all as specified.

Hacking out old broken glass (any thickness, size, quality or description) from MS frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads

S& F 3mm thick sheet glass ordinary quality n.exc 0.5sqm each pane complete.

S&F figured /frosted glass,4mm thick sheet glass ordinary quality n.exc 0.5sqm each pane and fixed in repairs.

S & F in repairs galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm fixing to steel window with nut bolt.

Demolition of Granite Stone slabs and tiles of any description or thickness laided bedded and pointed in cement mortar in floors, aprons etc.

M&L for 20mm thick Granite (of any type) slab laid over cement screed and jointed with grey cement slurry, and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete fixed over and including 15mm thick in CM 1:4 all as specified.

Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations.

Taking up or down 15 mm bore steel tubing and connections including disconnection of fittings and cleaning for refixing where required.

Taking up or down 20 mm bore steel tubing and connections including disconnection of fittings and cleaning for refixing where required.

Supplying & fixing to walls and ceiling 15 mm nominal bore, medium grade, galvanised coated steel tube conforming to IS 1239 (Part-1): 2004 including all fittings conforming to IS 1239 (Part-2): 2011 complete all as specified and as directed

All as per serial item No. 29 above but except steel tubing.

Supplying & fixing to walls and ceiling 20 mm nominal bore, medium grade, galvanised coated steel tube conforming to IS 1239 (Part-1): 2004 including all fittings conforming to IS 1239 (Part-2): 2011 complete all as specified and as directed

Cutting chases, pinning in concrete block or slab, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10cm girth.

S & F in repair stop valves(angle valve), cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions & fixed - bore dia of pipe 15 mm.

S & F in repair stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions & fixed - bore dia of pipe 15 mm but fancy type with long shank and cup ( concealed type) complete all as specified and directed by Engineer in Charge.

S&F in repairs 15mm dia fancy type Bib taps, cast copper alloy CP with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed.

S & F in repair,Chromium plated shower roses with or without swivel joints, 125mm size, including fixing to steel pipe or union

S & F in repairs Vitreous China Squatting pan Orissa pattern long pan, size 580 mmX440mm white with `P' or `S' trap, front or back inlet and foot rests any pattern including connection to trap and to flushing pipe, anti-syphonage pipe etc., including trap set in and including concrete complete including making good to floor.

S & F in repair PVC valveless syphonic action type flushing cistern (Low or high level) of 10 litre capacity, white/coloured with inlet ball valve, float, handle including fixing brackets and 32 mm bore PVC flush pipe etc complete all as specified and directed.

S&F plate rack made of stainless steel 1mm thick and overall size 915mm x 915mm x 255mm, inlcuding taking down old /unsv complete all as specified and directed.

S&F in repairs vitreous china wash basin white, flat back of size 450 x 300mm, excluding taps, waste chain & plug & porcelein stopper but including brackets, cutting for and pinning in ends of brackets including waste coupling and waste pipe all as directed. Make: Cat Part No S2040124 of CERA or equevlant make in Hindware/Somany.

S&F in repair pillar taps fancy type cast copper alloy with capestan heads chromiun plated screwed down high pressurewith hot &cold with long screwed shanks and fly nuts all as specified and directed.

S&F in repair ,stainless steel sink, 1mm thick, kitchen or laboratory with plugs, washers and waste; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm including waste coupling and waste pipe complete all as directed.

S & F PVC connections 15 mm size with PTMT nuts of 600 mm long

Taking down chowkats and frame n.exc 1.5 Sqm incl shutter with out taking off shutters from frame all as specified and directed by Engr-in-Charge.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S Square tube, supplying & fixing in opening as per specification & drawing

S&F to the frame at site, factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tube for top and bottom rails. MS frame shall be coverd with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail and bottom rail of either side and as gap insert for top rail and bottom rail; panelling of plain colour PVC sheet to be fitted in the MS frame welded / sealed in the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement, all as directed by Engineer -in -charge.

S & F 150 mm size extruded aluminium alloy handles, fabricated type anodised all as directed.

S & F aluminium anodised, barrel tower bolts of extruded section and fixed, length of bolt 150mm all as directed.

S&F 100 mm Stainless steel butt hinges medium weight, cold rolled all as directed.

Taking down chowkats and frame exc 1.5 Sqm and n. exc 4.0 sqm incl shutter with out taking off shutters from frame and removing from site specified and directed by Engr-in-Charge

S&F 105x60 mm Pressed steel frames made out of 1.25mm steel sheet for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., with one shop coat of red oxide primer complete, as specified, supplied and fixed all as specified and directed by Engr-in-Charge.

S&F 125x60 mm Pressed steel frames made out of 1.25mm steel sheet for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., with one shop coat of red oxide primer complete, as specified, supplied and fixed all as specified and as directed.

M&L cement concrete M-10 grade (Nominal mix) using 12.5mm graded stone aggregate as in blocks for fixing hold fasts and fillling of chowkhats or any other purpose all as specified.

Cutting holes in existing wall or PCC Block masonry built in cement mortar or cement lime mortar and stone walls built in lime mortar for inserting holdfast and making good dismantled portion in cement mortar 1:3 or cement concrete M-15 grate (nominal mix) using 20 mm graded stone agregate as required depth of embedded portion of holdfast or lugs measured from the face of jamb into the wall exceeding half brick but not exceeding one brick all as directed.

S & F 30mm thick flush shutters solid core construction with block board core and plywood face panels, commercial type on both sides all as directed.

S & F 35mm thick second class hard wood plain, framed , panelled shutter (2 panel) with lock rail and panel commercial ply or 12 mm veneered particle board of 9 mm B.W.P commercial veneering on both faces.The size of rail and stile as per IS:1003 (part-I), kiln seasoned and chemically pressure treated all as directed.

Supplied and fitted to chowkats 35 mm thick Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edge of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8. clause 8.20 (a); all as directed.

S&F in repairs 300mm, MS door springs including roller and roller plate complete all as sepcified and directed.

S & F 250mm long Mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed all as directed.

S & F steel ventilators with top hung shutters including hinges, steel peg stay with one coat of red oxide primer complete all as specified and as directed.

M & L for preparation of newly primed steel surfaces exc 10 cm width or girth and applying two coats of synthetic enameled paint complete all as specified.

M&L for preparation of new wooden surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified.

S & F galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm fixing to steel window with nut bolt, all as specified and directed.

S&F in repair 110 mm bore PVC (SWR) pipes type 'A' single socketed, in any length with rubber ring joints, fixed on walls complete all as specified.

S&F in repair 75 mm bore PVC (SWR) pipes type 'A' single socketed, in any length with rubber ring joints, fixed on walls complete all as specified.

S&F in repair, 110mm dia PVC (SWR) bends any radius, complete all as specified.

S&F in repair 75mm dia PVC (SWR) bends any radius, complete all as specified.

S&F in repair 110mm dia, PVC (SWR) branch piece, single (single Y) equal or unequal, for complete all as specified.

S&F in repair, 75mm dia PVC (SWR) branch piece, single (single Y) equal or unequal complete all as specified. .

S&Fin repair 110mm dia, PVC (SWR), junction single, (Single T) equal or unequal complete all as specified.

S&F in repair, 75mm dia PVC (SWR), junction single, (Single T) equal or unequal, pipe complete all as specified. .

S&F in repair harrison rails of MS chromium plated min 20mm with fixing brackets and other fittings complete.

Demolition of cement concrete (unreinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level) and removing the same off the premises complete all as specified and directed.

M&L for waterproofing treatment to RCC sunken slab as specified below. Make: PIDILITE or equivalent. (a) creating fillet coving of 50mmX50mm with polymer modified mortar using cement : sand : URP. (b) Applying PU sealant at the junction of pipes and the RCC sueface. (c) Apply1st coat of two component cementitious coating, over the surface and taking the coating on the walls over the angle fillet / watta portion. (d) Lay 40gsm geotextile fleece at the watta portion. (e) Apply 2nd coat of two component cementitious coating, over the first coat and taking the coating on the walls over the angle fillet / watta or vertical faces after 6 -8 Hrs. (f) Applying 12mm thick plaster in C:M 1:3 with liquid waterproofing compound as per manufacturere instructions.

M & L for PCC M-7.5 grade (nominal mix) uisng 40mm graded stone aggregate as in filling, mass concrete for sunken floor , all as specified and directed.

M & L for spot welding in repairs n exc 2.5 cm and thickness of welding n exc 6mm in luding necessary to be welded together holding the members in true position while welding and bevelling of edges as requied in the case of metal exc 3mm thick lenthe for steel window, cupboards and ventilators hinges, brackets, steel handle, etc. all as sepcified and directed.

S&F in repairs 75mm PVC (SWR) multifloor trap with grating including jointing with solvent cementcomplete all as specified and directed.

S & F in repairs rotational moulded polyethylene water storage tanks (Cylindrical vertical with closed top) of capacity 500 litre white colour triple layer alongwith ball valves suitable for 20mm bore iron pipe high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe hoisted and fixed in position including dismantling water tanks and removing from site complete all as specified and directed.

Demolition of cement concrete unreinforced of any description and in any position, not otherwise specifically provided for and M & L for cement concrete M-15 grade (nominal mix) using 12.5mm graded stone aggregates for filleting, benching, slightly rounding or chamfering on edges, filling undulations / depressions in roof surface, providing concrete platform for tanks wherever required as directed.

Taking down / removing existing water proofing treatment from RCC roof slab including removal of plaster bed below felt / membrane and disposal of the same to distance exceeding 50m but not exceeding 100m as and where directed and M & L for 10 mm thick screeding / rendering in cement mortar 1:4 on concrete roof surface, using liquid water proofing compound as per manufactureres instructions surface finished even and smooth without using extra cement all as directed. Note: Liquid Water Proofing Compound shall be measured and paid separately under relevant item of this BOQ.

Supply only liquid water proofing compound hydroseal-W+ or eqivalent (for plaster hardening, to contol efflorescence & fungal growth) as approved by GE.

M & L for applying APP (Atactic Poly Propylene) bitumen membrane 3mm thick APP modified weight not less than 3.60 Kg/Sqm reinforced with non woven polyester fibre of weight 160 gms/sqm as center core and without multiple layers of polyethylene, finished on top and bottom with 7 micron thick flammable polyethylene, applied by thermo fusion using LPG torch on the bottom portion of the membrane, after applying a coat of bituminous primer 0.40Kg/Sqm over roof ( An overlap of 100mm & 150mm shall be provided on sides and ends respectively ) all as per manufacturers instructions.

M&L 2nd Class hard wood Exc 13Sqcm & not exc 25 sq.cm, Plain fillets, square, rectangular or triangular in section, clean sawn, secured with mills or brads as in almirah frame/ chowkhats all as directed.

S&F in repairs 18/19mm thick Prelaminatd particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work all as sepcified and directed.

S&F in repairs 40 mm width Continuous (piano) hinges, mild steel, bright finish or electrogalvanised all as sepcified and directed.

S&F in repair Hasp and staple 75mm long, mild steel, wire type, stove enamelled black, including bolt to hinge plate and fixed with screws

S&F in repair 75mm Mild steel barrel tower bolts, stove enamelled black, with bright bolt and fixed

S&F in repair 75mm long Mild steel pressed handles, oval type, stove enamelled black

Taking down copper/aluminium point wiring (light, fan, socket or power) such as switches, ceiling roses, pendants, regulators, sockets, etc and making good disturbed surfaces of walls, floors, etc complete.

M & L for Point wiring with 1.5 Sqmm (nominal area) single core PVC insulated unsheathed (FRLS) cable, multi-stranded, copper conductor, in universal colour code with & including suitable size of rigid non-metallic PVC concealed conduit medium grade (not less then 20mm dia medium grade) and its all accessories complete concealed in wall incl cutting & chases( making good all to the disturbed surfaces as per existing) and modular flush metal boxes including cover plate with frame for mounting switches, sockets, regulators,socket etc including earth wire of PVC insulated (FRLS) copper conductor multistranded of 1.5 Sqmm size in green colour complete all as specified in current SSR Part-I & II & directed by the Engineer-in-Charge, as described below:-

One light point controlled by one switch

One fan point controlled by one switch.

One 5 pin 6 Amps socket outlet on independent board.

One 5 pin 6 Amps socket outlet on same board.

One Bell /buzzer point controlled by one push button on the same board with other switches or independent with cables 1.5 sqmm size.

All as per item No. 91 here-in-before but wiring with 2.5 sqmm single core multi stranded copper condcutor 1100 V grade PVC insulated but unsheheted copper conductor FR cable 1100 volts grade and 2.5 sqmm PVC insulated but unsheathed FR cable as earthwire for 16 Amps power point on independent board complete all as specified and directed by Engr-in-charge.

S & F switch piano type 250 volts single pole one way 6 Amps all as Specified and directed.

S & F socket outlet 5 pin 6 Amps shuttered flush type all as Specified and directed.

S & F switch piano type 250 volts single pole one way 16 Amps all as Specified and directed.

S & F socket outlet 2 in 1, 3 pin 6 and 16 Amps flush type all as Specified and directed.

Supply and Fixing PVC ceiling rose/ Angle Holder/ Batten Holder surface type three terminals type all as specified and directed.

S & F fan regulators electronic step type suitable for 1200mm/1400mm sweep ceiling fans.

S & F Bell push flush type 5 Amps 230 V all as directed by engineer-in-charge

S & F Bell Ding Dong AC 230 V all as directed by engineer-in-charge

Taking down unserviceable conventional fitting and S&F wall mounted high quality indoor batten led tube light with PVC housing, T-8 LED tube rod 20 Watt with T-8 LED Batten type with integral electronic driver 20 W, colour temprature 6500 K (4'), operating lifte 50000 hrs, lumen 1800-3000, diffused connecting with three core flexible copper wire from connector to ceiling rose/ Angle Holder as per existing site requirement as directed by engineer in charge. Make Halonix/Havells/ Crompton Greaves

Supply & fix LED light fitting mirror type with high output diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete.

M & L for sub main wiring but using two single core muiltistranded PVC insulated copper conductor FRLS cable of size 4 sqmm 1100 volt grade drawn into PVC concealed conduit including 4 sqmm PVC multi standard copper conductor FRLS cable in green colour for continious earthing including chislling / cutting of wall, floor, making hole through wall & making good disturbed surfaces of wall/floor/ceiling to match with existing surface, including taking down the existing u/s submain wiring complete all as specified and directed by Engineer in Charge. Note : Two runs of 4 Sqmm cable, one run of 4 Sqmm earth cable and one run of PVC conduit shall be measured as one unit length.

S & F distrubtion board factory made TPN 4 way in, 415 Volt, Double door metal type suitable provision for fixing MCBs as out going, TPN MCB 63 Amps as main incoming all as specified and directed.

Supply and Fixing distribution board factory made SPN 8 way in, 240 Volt, Double door metal type suitable provision for fixinf MCBs as out going and SPN MCB 32 Amps as main incoming all as specified & directed. Note: Cost of MCBs shall be measured abd paid seperately under relevant item of this BOQ.

S & F Isolator TPN 63 Amps all as specified & directed.

S & F Isolator MCB DP 32 Amps all as specified & directed.

S & F Isolator MCB SP 5 to 32 Amps all as specified & directed.

Supply and fixing PVC black plate suitable for MCB DB complete all as specified and as directed.

Taking down ceiling fan 1200mm/1400mm & M & L for machine spray painting of ceiling fan of any make/ sweep with synthetic enameled paint after preparation of old surface by cleaning with soap/ detergent and drying of white synthetic enameled paint including writing of MES No. with black synthetic enameled paint with existing pattern all as directed by Engineer-in-charge.

M & L overhauling and painting of building panel board including complete removal of existing paint and applying two coat of synthetic enamlled paint over a coat of red oxide & necessary welding to hinges including replacement of connection wire 4 sqmm from TPN DP to existing electric meter lugs, cable glands and etc. necessary connection wire to meter all as directed Engineer-in-charge.

Material and labour for earthing complete with GI earth plate 600mm x 600mm x 6 mm thick electrode buried directly in ground (earth pit not less then 2.25 metres deep below ground level ) with top edge of the plate not less then 1.5 metres below normal ground level connected to GI wire 4.0 mm as earth lead by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 of MES schedule Part-I and incl 15 mm bore light grade GI protection pipe (upto 7.5 metres beyond outer edge of earth pit) PCC M-10 grade (Nominal Mix) using 40mm graded stone aggregate in pit with 40mm thick RCC cover in reinforced cement concrete M-15 grade (Nominal Mix) using 20mm graded stone aggregate, reinforced with 8mm dia bar both way @ 150mm c/c, watering arrangement with funnel and wire mesh and 20 mm bore light grade GI watering pipe, common salt and chaarcoal filling, necessary excavation and earth work complete. Note: Rate for achieving required depth by compressor machine/breaker if required is deemed included in item unit rate.

M & L for earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried inground or drawn inconduit/ pipe or fixed to poles or any other indicated suituation for loop earthing etc. as required 4 mm dia galvanised iron or steel wire, including taking down the existing u/s earth continuity conductor complete all as specified and directed by Engineer-in-charge.

M & L for Rendendring 10 mm thick on fair faces of brick work or contreat surfaces with cement plaster 1:4 complete all as directed by Engineer-in-charge.

s.k.engineers

Veekay Enterprises

S.R.M.K Enterprises

VAISHNAVI CONSTRUCTION