REPAIR AND MAINT TO WATER SUPPLY, CI / DI / GI DISTRIBUTION NETWORK, CHLORINATION EQUIPMENT, SUMMER AND WINTER APPLIANCES AND CONNECTED WORKS AT SUNJUWAN UNDER GE JAMMU

Amount

Material and labour for lifting of unserviceable submersible motor and pump set of capacity 50 to 60 HP, three phase from bore hole of tubewell by disconnecting column pipes one by one with the help of chain pulley block after all disconnecting electrical and water connections from pump set and transporting the same to workshop after de-coupling motor and pump for carrying out repair and bringing back the same to site, lowering of coupled motor pump set in borewell by making submersible cable joint water proof, flange joints with new nuts, bolts and washers, leather gasket / packing with proper alignment, binding of cable with column pipe and testing on completion complete all as specified and as directed. Notes: - (i) Cost of taking up and lowering of column pipes, transportation of pumps and motor to workshop and back shall be deemed to be included in the rate quoted. (ii) Required T&P such as chain pulley block shall be contractor's responsibility. (iii) Repair / replacement shall be done within a period as intimated by the Engineer-in-Charge failing which necessary recovery shall be made.

Material and labour for lifting of unserviceable submersible motor and pump set of capacity 35 to 50 HP, three phase from bore hole of tubewell by disconnecting column pipes one by one with the help of chain pulley block after all disconnecting electrical and water connections from pump set and transporting the same to workshop after de-coupling motor and pump for carrying out repair and bringing back the same to site, lowering of coupled motor pump set in borewell by making submersible cable joint water proof, flange joints with new nuts, bolts and washers, leather gasket / packing with proper alignment, binding of cable with column pipe and testing on completion complete all as specified and as directed. Notes: - (i) Cost of taking up and lowering of column pipes, transportation of pumps and motor to workshop and back shall be deemed to be included in the rate quoted. (ii) Required T&P such as chain pulley block shall be contractor's responsibility. (iii) Repair / replacement shall be done within a period as intimated by the Engineer-in-Charge failing which necessary recovery shall be made.

Material and labour for lifting of unserviceable submersible motor and pump set of capacity 10 to 30 HP, three phase from bore hole of tubewell by disconnecting column pipes one by one with the help of chain pulley block after all disconnecting electrical and water connections from pump set and transporting the same to workshop after de-coupling motor and pump for carrying out repair and bringing back the same to site, lowering of coupled motor pump set in borewell by making submersible cable joint water proof, flange joints with new nuts, bolts and washers, leather gasket / packing with proper alignment, binding of cable with column pipe and testing on completion complete all as specified and as directed. Note: - (i) Cost of taking up and lowering of column pipes, transportation of pumps and motor to workshop and back shall be deemed to be included in the rate quoted. (ii) Required T&P such as chain pulley block shall be contractor's responsibility. (iii) Repair / replacement shall be done within a period as intimated by the Engineer-in-Charge failing which necessary recovery shall be made.

Material and labour for lifting of unserviceable submersible motor and pump set of capacity below 10 HP, three phase from bore hole of tubewell by disconnecting column pipes one by one with the help of chain pulley block after all disconnecting electrical and water connections from pump set and transporting the same to workshop after de-coupling motor and pump for carrying out repair and bringing back the same to site, lowering of coupled motor pump set in borewell by making submersible cable joint water proof, flange joints with new nuts, bolts and washers, leather gasket / packing with proper alignment, binding of cable with column pipe and testing on completion complete all as specified and as directed. Note: - (i) Cost of taking up and lowering of column pipes, transportation of pumps and motor to workshop and back shall be deemed to be included in the rate quoted. (ii) Required T&P such as chain pulley block shall be contractor's responsibility. (iii) Repair / replacement shall be done within a period as intimated by the Engineer-in-Charge failing which necessary recovery shall be made.

Material and labour for dismantling, strip opening complete submersible motor set having capacity 50 to 60 HP any stage / discharge and dismantling all spare parts by opening studs complete with machine / lathe work / grinding / polishing and fitting of all spare parts and re-assembling / installation in position after necessary repair / replacement of unserviceable / defective spare parts complete all as specified and as directed. Note: - Spare parts shall be measured and paid separately under respective items.

Material and labour for dismantling, strip opening complete submersible motor set having capacity 35 to 50 HP any stage / discharge and dismantling all spare parts by opening studs complete with machine / lathe work / grinding / polishing and fitting of all spare parts and re-assembling / installation in position after necessary repair / replacement of unserviceable / defective spare parts complete all as specified and as directed. Note: - Spare parts shall be measured and paid separately under respective items.

Material and labour for dismantling, strip opening complete submersible motor set having capacity 10 to 30 HP any stage / discharge and dismantling all spare parts by opening studs complete with machine / lathe work / grinding / polishing and fitting of all spare parts and re-assembling / installation in position after necessary repair / replacement of unserviceable / defective spare parts complete all as specified and as directed. Note: - Spare parts shall be measured and paid separately under respective items.

Material and labour for dismantling, strip opening complete submersible motor set having capacity below 10 HP any stage / discharge and dismantling all spare parts by opening studs complete with machine / lathe work / grinding / polishing and fitting of all spare parts and re-assembling / installation in position after necessary repair / replacement of unserviceable / defective spare parts complete all as specified and as directed. Note: - Spare parts shall be measured and paid separately under respective items.

Material and labour for taking out submersible motor shaft, refitting / refilling of metal at corroded portion including all welding, turning and other machine works required to make the shaft fit to shape and size as suitable for 50 to 60 HP complete all as specified and as directed.

Material and labour for taking out submersible motor shaft, refitting / refilling of metal at corroded portion including all welding, turning and other machine works required to make the shaft fit to shape and size as suitable for 35 to 50 HP complete all as specified and as directed.

Material and labour for taking out submersible motor shaft, refitting / refilling of metal at corroded portion including all welding, turning and other machine works required to make the shaft fit to shape and size as suitable for 10 to 30 HP complete all as specified and as directed.

Material and labour for taking out submersible motor shaft, refitting / refilling of metal at corroded portion including all welding, turning and other machine works required to make the shaft fit to shape and size as suitable for below 10 HP complete all as specified and as directed.

Supply and fixing in replacement thrust plate with key for submersible motor of capacity from 50 to 60 HP complete all as specified and as directed.

Supply and fixing in replacement thrust plate with key for submersible motor of capacity from 35 to 50 HP complete all as specified and as directed.

Supply and fixing in replacement thrust plate with key for submersible motor of capacity from 10 to 30 HP complete all as specified and as directed.

Supply and fixing in replacement thrust plate with key for submersible motor of capacity below 10 HP complete all as specified and as directed.

Supply and fixing in replacement gun metal bush for submersible motor cover of capacity from 50 to 60 HP complete all as specified and as directed.

Supply and fixing in replacement gun metal bush for submersible motor cover of capacity from 35 to 50 HP complete all as specified and as directed.

Supply and fixing in replacement gun metal bush for submersible motor cover of capacity from 10 to 30 HP complete all as specified and as directed.

Supply and fixing in replacement gun metal bush for submersible motor cover of capacity below 10 HP complete all as specified and as directed.

Supply and fixing in replacement thrust plate bearing for submersible motor of capacity from 50 to 60 HP complete all as specified and as directed.

Supply and fixing in replacement thrust plate bearing for submersible motor of capacity from 35 to 50 HP complete all as specified and as directed.

Supply and fixing in replacement thrust plate bearing for submersible motor of capacity from 10 to 30 HP complete all as specified and as directed.

Supply and fixing in replacement thrust plate bearing for submersible motor of capacity below 10 HP complete all as specified and as directed.

Supply and fixing in replacement stainless steel / gun metal bush for submersible motor of capacity from 50 to 60 HP complete all as specified and as directed.

Supply and fixing in replacement stainless steel / gun metal bush for submersible motor of capacity from 35 to 50 HP complete all as specified and as directed.

Supply and fixing in replacement stainless steel / gun metal bush for submersible motor of capacity from 10 to 30 HP complete all as specified and as directed.

Supply and fixing in replacement stainless steel / gun metal bush for submersible motor of capacity below 10 HP complete all as specified and as directed.

Supply and fixing in replacement oil seal for submersible motor of capacity from 50 to 60 HP complete all as specified and as directed.

Supply and fixing in replacement oil seal for submersible motor of capacity from 35 to 50 HP complete all as specified and as directed.

Supply and fixing in replacement oil seal for submersible motor of capacity from 10 to 30 HP complete all as specified and as directed.

Supply and fixing in replacement oil seal for submersible motor of capacity below 10 HP complete all as specified and as directed.

Material and labour for strip opening complete submersible pumping set having capacity 10 to 30 HP any stage / discharge and dismantling all spare parts by opening studs complete with machine / lathe work / grinding / polishing and fitting of all spare parts and re-assembling / installation in position after necessary repair / replacement of unserviceable / defective spare parts complete all as specified and as directed. Note: - Spare parts shall be measured and paid separately under respective items as under: -

Supply only cast iron stage bowl.

Supply only cast iron suction discharge chamber

Supply only gun metal body neck ring

Supply only gun metal body bowl bushes

Supply only body coupling sleeves

Supply only cast iron impeller with key

Supply only body studs fully threaded

Supply only stainless steel pump shaft

Supply only stainless steel pump shaft coupling with key

Supply only cast iron NRV with NRV seat and cone

Material and labour for strip opening complete submersible pumping set having capacity 35 to 60 HP any stage / discharge and dismantling all spare parts by opening studs complete with machine / lathe work / grinding / polishing and fitting of all spare parts and re-assembling / installation in position after necessary repair / replacement of unserviceable / defective spare parts complete all as specified and as directed. Note: - Spare parts shall be measured and paid separately under respective items as under: -

Supply only cast iron stage bowl

Supply only cast iron suction discharge chamber

Supply only gun metal body neck ring

Supply only gun metal body bowl bushes

Supply only body coupling sleeves

Supply only cast iron impeller with key

Supply only body studs fully threaded

Supply only stainless steel pump shaft

Supply only stainless steel pump shaft coupling with key

Supply only cast iron NRV with NRV seat and cone

Material and labour for strip opening to submersible motor having capacity below 10 HP and re-winding with super enamelled copper winding wire heavy duty heat resistance confirming to IS of same gauge and no's of turns complete with realignment of motor slots and insulating mateials i.e. varnishing, bamboo strips, leather papers, cotton tapes including replacement of unserviceable / defective spare parts and drying complete and re-assembling after repair / rewinding and testing at site on full head with spares required at site complete all as specified and as directed by Engineer-in-Charge.

Material and labour for strip opening to submersible motor having capacity below 10 to 30 HP and re-winding with super enamelled copper winding wire heavy duty heat resistance confirming to IS of same gauge and no's of turns complete with realignment of motor slots and insulating mateials i.e. varnishing, bamboo strips, leather papers, cotton tapes including replacement of unserviceable / defective spare parts and drying complete and re-assembling after repair / rewinding and testing at site on full head with spares required at site complete all as specified and directed by Engineer-in-Charge.

Material and labour for strip opening to submersible motor having capacity below 35 to 60 HP and re-winding with super enamelled copper winding wire heavy duty heat resistance confirming to IS of same gauge and no's of turns complete with realignment of motor slots and insulating mateials i.e. varnishing, bamboo strips, leather papers, cotton tapes including replacement of unserviceable / defective spare parts and drying complete and re-assembling after repair / rewinding and testing at site on full head with spares required at site complete all as specified and as directed by Engineer-in-Charge.

Dismantling and strip opening the motor completely including disconnecting the cable connections and coupling of the motor removing the stator and rotor units, bearings complete servicing the motor assembly including taking out damaged / burnt out winding, cleaning the slots and rewinding the same with new super enamelled copper winding wire of existing gauge and turns, also heat varnishing the motor windings by applying varnish and keeping the windings into the hot air oven till the moisture evaporates complete at authorized workshop, including replacement of required bearing, transportation and refit the same after repairs including connecting up of the electric connections complete, including testing and commissioning complete all as specified and as directed by Engineer-in-Charge for the following capacities: -

Motor 3 Phase, 10 HP capacity.

Motor 3 Phase, 5 HP capacity.

Labour for welding, metalling, grinding, polishing and lathe / machine work for re-alignment to rotor assembly and making the suitable size for fitment of rotor bearing complete with replacement of unserviceable / defective spare parts of submersible pump of capacity 10 to 20 HP complete all as specified and as directed. Note: - Spare parts shall be measured and paid separately under respective items as under: -

Supply only rotar sleeves stainless steel

Supply only rotar GM bearing bush

Supply only rotar upper and lower bearing housing

Labour for welding, metalling, grinding, polishing and lathe / machine work for re-alignment to rotar assembly and making the suitable size for fitment of rotar bearing complete with replacement of unserviceable / defective spare parts of submersible pump of capacity 30 to 50 HP complete all as specified and as directed. Note: - Spare parts shall be measured and paid separately under respective items as under: -

Supply only rotar sleeves stainless steel.

Supply only rotar GM bearing bush

Supply only rotar upper and lower bearing housing

Supply and fixing in replacement of cast iron discharge head assembly suitable for vertical turbine plumbing set having suction / discharge size 150 mm dia complete all as specified and as directed by Engineer-in-Charge.

Material and labour for strip opening complete vertical turbine pumping set having capacity 20 to 50 HP any stage / discharge and dismantling all spare parts by opening studs complete with machine / lathe work / grinding / polishing and fitting of all spare parts and re-assembling installation in position after necessary repair / replacement of unserviceable / defective spare parts complete all as specified and as directed. Note: - Spare parts shall be measured and paid separately under respective items as under: -

Supply only cast iron bowl.

Supply only cast iron suction / discharge bowl.

Supply only gun metal body neck ring.

Supply only cast iron impellers with key.

Supply only impeller lock bush.

Supply only cast iron NRV with seat

Supply only stainless steel shaft sleeves

Supply only shaft rod with coupling

Supply only shaft retainer of existing size

Supply and fixing in replacement mild steel pipe heavy grade 100 to 150mm dia bore, 10 feet long each with flanges, screwed and welded both ends complete with nuts, bolts, gasket etc lowered into bore well complete all as specified and as directed. Note: - The pipe shall be heavy duty not less than 6mm thick of wall and the flanges shall have grooves to accommodate the submersible cables and slings.

Supply and fixing in replacement mild steel pipe heavy grade 80 to 100mm dia bore, 10 feet long each with flanges, screwed and welded both ends complete with nuts, bolts, gasket etc lowered into bore well complete all as specified and as directed. Note: - The pipe shall be heavy duty not less than 6mm thick of wall and the flanges shall have grooves to accommodate the submersible cables and slings.

Supply and fixing in replacement mild steel pipe heavy grade upto 80mm dia bore, 10 feet long each with flanges, screwed and welded both ends complete with nuts, bolts, gasket etc lowered into bore well complete all as specified and as directed. Note: - The pipe shall be heavy duty not less than 6mm thick of wall and the flanges shall have grooves to accommodate the submersible cables and slings.

Material and labour for strip opening to VT motor having capacity 10 to 40 HP and re-winding with super enamelled copper winding wire heavy duty heat resistance confirming to IS of same gauge and no's of turns complete with realignment of motor slots and insulating materials i.e. varnishing, bamboo strips, leather papers, cotton tapes including replacement of unserviceable / defective spare parts and drying complete and re-assembling after repair / rewinding and testing at site on full head complete all as specified and as directed. Note: - Spare parts shall be measured and paid separately under respective item as under: -

Supply only rotor bearing cover sleeves.

Supply only thrust plate bearing housing.

Supply only thrust bearing for motor.

Supply only rubber oil seal.

Supply only cast iron sand guard.

Supply only ball bearing.

Dismantling and strip opening the pump completely including disconnecting the suction delivery, vacuum pipe lines and coupling for repairs to pump and refixing the same after repairs including overhauling the pump set, renewal of gasket to pump, suction and delivery lines, gland packing, greasing nuts, bolts and washers etc complete all as specified and as directed by Engineer-in-Charge for the following capacities: - Note: - Spare parts shall be measured and paid separately under respective item as under: -

Pump 200 HP to 250 HP.

Pump 100 HP.

Pump 60 HP.

Supply only the following items suit to the centrifugal pump set of capacity 100 HP, type 100 / 150, LGME MK-1 complete all as specified and as directed.

Pump Shaft.

Metal distance bushes.

Cross rings for impellers of suitable size.

Metal distance guides.

Impeller guide bush.

Impeller lock nut.

Shaft sleeves.

Gland bushes.

Gland Sleeves.

Steel checknut for shaft.

Supply only the following items suit to the centrifugal pump set of capacity 200 to 250 HP type DSM 150 / 46 complete all as specified and as directed.

Pump Shaft.

Metal distance bushes.

Cross rings for impellers of suitable size.

Metal distance guides.

Impeller guide bush.

Impeller lock nut.

Shaft sleeves.

Gland bushes.

Gland Sleeves.

Metal gland with studs and nuts.

Steel checknut for shaft.

Supply only the following items suit to the centrifugal pump set of capacity 60HP complete all as specified and as directed.

Pump Shaft.

Metal distance bushes.

Cross rings for impellers of suitable size.

Metal distance guides.

Impeller guide bush.

Impeller lock nut.

Bronge impellers.

Gun metal shaft sleeves.

Gun metal gland bush.

Gun metal gland sleeves.

Metal gland with studs and nuts.

Steel checknut for shaft.

Supply and fixing the following spare parts suitable for 60 / 100 / 200 / 250 HP centrifugal pump set including removing of old unserviceable items complete all as specified and as directed: -

Pressure gauge of size 100 mm dia 10 Kg / cm complete with brass coupling cock 3/8".

Tyre coupling of existing size for 250 to 60 HP.

Dismantling and strip opening the motor completely including disconnecting the cable connections and coupling of the motor removing the stator and rotor units, bearings complete servicing the motor assembly including taking out damaged / burnt out winding, cleaning the slots and rewinding the same with new super enamelled copper winding wire of existing gauge and turns, also heat varnishing the motor windings by applying varnish and keeping the windings into the hot air oven till the moisture evaporates complete at authorized workshop, including transportation and refit the same after repairs including connecting up of the electric connections complete including testing and commissioning complete all as specified and as directed by Engineer-in-Charge for the following capacities: -

Motor 3 Phase 100 HP capacity.

Motor 3 Phase 60 HP capacity.

Supply and fixing renewal of worn out / unserviceable ball / roller bearing from the induction motor / pumping set with the same size and capacity for the following motors complete all as specified and as directed by Engineer-in-Charge : -

Ball bearing for Electric motor / pump of capacity 200 / 100 HP, 3 Phase.

Ball bearing for Electric motor / pump of capacity 60 HP, 3 Phase.

Material and labour for metalling to the shaft with turning, levelling, finishing etc suit the centrifugal pump set of the following capacity complete all as specified and as directed by Engineer-in-Charge: -

Shaft suitable for 200 HP pump set.

Shaft suitable for 100 HP pump set.

Shaft suitable for 60 HP pump set.

Supply and fixing in repair fully automatic star delta motor starter in sheet steel enclosure type MN 32 FASD with single phase protection feature and motor rating AC-3 duty, 415 volt, 50 Hz, 3 phase suitable for up to 35 HP motor pump set complete all as specified and as directed.

Supply and fixing in repair fully automatic star delta motor starter in sheet steel enclosure type MN 32 FASD with single phase protection feature and motor rating AC-3 duty, 415 volt, 50 Hz, 3 phase suitable for up to 60 HP motor pump set complete all as specified and as directed.

Supply and fixing in replacement fountain lights with LED 12 V, 3 X 3 watt colourful water proof underwater submersible fountain lights in RGB combination of colours, IP-68 complete all as specified and as directed by Engineer-in-Charge.

Excavation in trenches not exceeding 1.5 metre wide and not exceeding 1.5 metre in depth (for taking up or laying of CI / GI pipes) and getting out in soft / loose soil complete all as specified and as directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm complete all as specified and as directed.

Removing excavated surplus soils not exceeding 50 metre and deposited where directed at a level not exceeding 1.5 metre above the starting point complete all as specified and as directed.

Labour for repair / rectification of leakage of underground CI / DI pipe line of size 80 to 200 mm bore dia in position complete with excavation approximate 1.5 X 1.5 X 1.5 metre around the leakage, returning, filling in, removal, cutting / dismantling of leakage complete with and including cocking to existing lead joint, filling new lead joint burning and taking out existing lead joint as per site requirement and restore the water supply complete all as specified and as directed. Note: - Spare / fitting shall be measured and paid separately.

Material and labour in repair for run lead joint for CI spigot and socket pipes and fittings 150 to 200 mm bore with new lead complete all as specified and as directed.

Material and labour in repair for run lead joint for CI spigot and socket pipes and fittings 80 to 100 mm bore with new lead complete all as specified and as directed.

Cutting to existing cast iron pipes of size 80mm to 150mm dia in position for insertion of new fitting such as Tee, Collar, branches etc, as per site requirement complete all as specified and as directed by the Engineer-in-Charge. Note: - Fittings shall be measured and paid separately.

Labour for drilling and tapping cast iron water mains (in position) for branch connections of internal dia 15 mm pipe complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing in repair CI / DI specials for spigot and socketed CI / DI pipes 150mm dia, such as connecting pieces one end flanged and other socket or spigot and bell mouth pieces one end flanged other end tapering as bell mouth all as specified and directed by Engineer-in-Charge.

Material and labour in repair for cast iron non return valve suitable for 150 mm bore pipe both end flanged and fixed to the existing pipe line including joint with nut, bolt, washers, rubber or fibre board gasket, etc including taking down old one complete all as specified and as directed.

Material and labour for cast iron sluice valve both end flanged class PN 1.0 conforming to IS-14846-2000 with iron wheel head and brass spindle including necessary joint with nuts, bolt, washer, rubber or fibre board gasket, etc including taking down old one suitable for the following bore of pipes complete all as specified and as directed: -

200 mm bore.

150 mm bore.

100 mm bore.

80 mm bore.

Taking up or down existing leakage GI pipe line in position of any length (RM) for repair / rectification of leakage, replacement of unserviceable fittings and welding work as per site from trenches / walls / floors / ceiling etc and keeping serviceable pipes in safe custody for reuse at same site or other as directed and restore the water supply for the following bore of pipes: -

80 mm bore.

50 mm bore.

40 mm bore.

25 mm bore.

20 mm bore.

15 mm bore.

Supply and fixing in repair galvanised steel tubes, medium grade, laid in trenches with all fittings such as tee, socket, bends, union etc all as required and complete all as specified and directed for the following bore of pipes: - Note: - Rate quoted should include GI sockets, GI nipples, GI unions, GI bends / reducers all as required at site.

80 mm bore.

50 mm bore.

40 mm bore.

25 mm bore.

20 mm bore.

Supply and fixing in repair galvanised steel tubes medium grade, with all fittings such as tee, socket, bends, union etc and fixed complete to walls and ceiling or laid in floors complete all as specified and directed for the following bore of pipes: - Note: - Rates quoted should include GI sockets, GI nipples, GI unions, GI bends / reducers all as required at site.

25 mm bore.

20 mm bore.

15 mm bore.

Material and labour for 50 mm bore gun metal, gate valve with iron wheel head, screwed both ends for iron pipes and fixed complete in existing position including taking down old one complete all as specified and as directed.

Material and labour for 40 mm bore gun metal, gate valve with iron wheel head, screwed both ends for iron pipes and fixed complete in existing position including taking down old one complete all as specified and as directed.

Material and labour for 25 mm bore gun metal, gate valve with iron wheel head, screwed both ends for iron pipes and fixed complete in existing position including taking down old one complete all as specified and as directed.

Material and labour for 20 mm bore gun metal, gate valve with iron wheel head, screwed both ends for iron pipes and fixed complete in existing position including taking down old one complete all as specified and as directed.

Material and labour for 15 mm bore gun metal, gate valve with iron wheel head, screwed both ends for iron pipes and fixed complete in existing position including taking down old one complete all as specified and as directed.

Demolition of cement concrete in ground floor and paving not exceeding 15 cm thickness (below or above ground level) complete all as specified and as directed.

Material and labour for 75 mm thick, plain cement concrete (1:3:6), type C-2 (using 40 mm graded crushed stone aggregate) as in paving / footpath and finished the surface even and smooth without using extra cement and making impression of expanded metal, whilst the concrete is green complete all as specified and as directed.

Material and labour for cleaning to overhead RCC reservoir of any capacity internally at approximate 40 feet high stagging by using water treatment chemical / bleaching powder / Sodium hypochloride chemical including cleaning internally entire wall surface, removing deposited particular, scrubbing complete wall surface and applying coat treatment water chemical on complete wall and drain out the water after disconnecting all rising / distribution sluice valves complete with painting to mild steel / steel railing / rising / distribution / wash out CI pipe with different colour all as specified and as directed and writing date of tank cleaning.

Material and labour for cleaning to underground sumps of any capacity (2.5 LG to 1.0 LG) internally by using water treatment chemical / bleaching powder / Sodium hypochloride chemical including cleaning internally entire wall surface, removing deposited particular, scrubbing complete wall surface and applying coat treatment water chemical on complete wall and drain out the water after disconnecting all rising / distribution sluice valves complete with painting to mild steel / steel railing / rising / distribution / wash out CI pipe with different colour all as specified and as directed and writing date of tank cleaning.

NOTES FOR SER ITEM NO 79.00 AND 80.00: - (i) The unit rate quoted deemed to be including draining of water with mechanical equipment and working in water and mud etc. (ii) The unit rate quoted deemed to be including all safety precautions which shall be taken while working on RCC overhead tank / underground sump and contractor or his Engineer shall be available during execution of the job. (iii) Lighting arrangements if required to be provided by the contractor temporarily at his own arrangements and the amount quoted for that is deemed to be inclusive in the unit rate and electricity / diesel shall not be provided by the MES. (iv) Contractor will not be allowed more than one day to do the work inside each overhead tank / underground sump to prevent interruption of water to the users.

Supply and fixing in repair the water level indicator with replacement of GI pulley (02 No's), GI wire rope (20 RM), float valve painting of indicator, scales with black / red paints, marking of numbers on scales complete all as specified and as directed (as required at site).

Taking out unserviceable / damage sluice valve pit mild steel top cover along with angle iron frame for repair, denting, necessary welding work, provision of replacement of two no's of mild steel hinges 6" heavy duty and provision of lifting handle and refixing in position alongwith angle iron frame with the help of nut, bolt after necessary repair / in position as per site requirement complete all as specified and as directed.

Supply and fixing in repair mild steel sheet 3 mm thick for top cover of valve pits including cutting to required size and welding to hinges all as required at site complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing in repair cast iron air release valve with double air outlet / orifice, 50mm bore conforming to IS-14845-2000 suitable for 150 / 200mm dia main water line complete all as specified and as directed.

Supply and laying in trenches / on floor, jointing and testing ductile iron pipe with spigot and socket ends of 150mm dia special class K-7 suitable for tyton jointing material conforming to IS-8329 in repair complete all as specified and as directed.

Supply and laying in trenches / on floor, jointing and testing ductile iron pipe with spigot and socket ends of 100mm dia special class K-7 suitable for tyton jointing material conforming to IS-8329 in repair complete all as specified and as directed.

Material and labour for cleaning of valve pit chamber with sluice valve, pipes etc including replacement of existing wornout / defective gland packing, nut, bolt and washer, etc with new one to make the sluice valve perfectly leak proof including one coat of synthetic enamel paint after preparation of old steel surfaces complete all as specified and directed by the Engineer-in-Charge for the following size: -

80 mm to 100 mm dia.

Material and labour in replacement of ball valve, high pressure with teflon sheet screwed both ends for iron pipes and fixed complete in existing position including taking down old one complete all as specified and as directed.

15 mm bore.

20 mm bore.

25 mm bore.

Dismantling and taking down electric motor of dozing system and shifting in workshop for repair and rewinding with super enamelled copper winding wire of same gauge and no's of turns complete with insulated material i.e. varnish, cotton tape, bamboo strips, emory paper and drying including replacement of unserviceable spare parts complete all as specified and as directed. Note: - Spare parts shall be measured and paid separately under respective items.

Supply only motor seal.

Supply only motor bearing.

Supply only motor fan blade.

Supply only rotor shaft.

Dismantling and taking down dozing pumping set and shifting in workshop for repair / maintenance / overhauling and reassembly after necessary repair complete with and including replacement of unserviceable / defective spare parts and tested on load at site complete all as specified and as directed. Note: - Spare parts shall be measured and paid separately under respective items.

Supply only Agitator assembly.

Supply only Agitator bearing.

Supply only Agitator shaft with SS blade duty FRP coated.

Supply only foot valve.

Supply only suction NRV.

Supply only discharge NRV.

Supply only injection valve (line NRV) fitting.

Supply only PE Hard tubing transparent 6 / 8mm.

Supply only solenoid motor.

Supply only main head (PP / PVC).

Supply only main head hexagonal bolts.

Supply only diaphragam (taflon faced).

Supply only Acrylic front cover.

Supply only speed / stroke nob.

Supply only toggle switch.

Supply only strainer for foot valve.

Supply only pressure relief valve.

Supply and fixing in replacement of heavy duty FRP service tank 100 litres complete with drain valve, level gauge, water inlet / outlet, provision and CPV 15 mm pipe for feeding to main line complete all as specified and as directed.

Material and labour in replacement for fabricated mild steel angle iron frame heavy duty epoxy coated and anticorrosive paint bend to shape bending, welding and fixing on wall / floor to take the load of complete dozing system to avoid direct load of motor on tank complete as specified and directed by the Engineer-in-Charge.

Supply only Altoch-GP / Aquafit calcium based granular disinfectant for water treatment more stable their chlorine gas and stronger than bleaching powder packing in 45 kg plastic drum complete all as specified and as directed.

Material and labour for replacement of unserviceable and worn out parts of 2 to 5 HP motor and rewinding with super enamelled heat resistance copper winding wire of the recommended gauge and number of turns with all insulation material including cleaning and varnishing the motor replacing unserviceable bearing, nuts and bolts complete all as specified and as directed.

Comprehensive repair, maintenance and servicing of silver ionisation plant SMPS and control panel at installations complete all as specified and as directed. Note: - The rates shall be deemed to include the cost of all spares and checking of the electronic circuit control for the electrode.

Supply and fixing in repair silver ionisation electrode suitable for plant of capacity 1.5 lakh litres per hours Model BW/Eco 150 or equivalent as approved by GE complete all as specified and as directed.

Construction of brick masonary valve pit chamber of 1050 x 1050 x 1050 mm sizes (internal dimensions) with MS sheet cover 6 mm thick and angle iron 40 x 40 x 6 mm frame duly painted with two coat of synthetic enamel paint over one coat of red oxide primer including locking arrangement, necessary earth work etc complete all as specified and as directed.

Construction of brick masonary valve pit chamber of 900 x 900 x 900 mm sizes (internal dimensions) with MS sheet cover 6 mm thick and angle iron 40 x 40 x 6 mm frame duly painted with two coat of synthetic enamel paint over one coat of red oxide primer including locking arrangement, necessary earth work etc complete all as specified and as directed.

Construction of brick masonary valve pit chamber of 600 x 600 x 600 mm sizes (internal dimensions) with MS sheet cover 6 mm thick and angle iron 40 x 40 x 6 mm frame duly painted with two coat of synthetic enamel paint over one coat of red oxide primer including locking arrangement, necessary earth work etc complete all as specified and as directed.

Labour for repair / servicing of ceiling fan of any capacity complete with strip opening the ceiling fan for repair / washing / varnishing and removing of old lubricating substance from bearing / bush using Kerosine oil, carrying out fresh lubrication using grease and to make the ceiling fan noise free for smooth functioning, including replacement of worn out / unserviceable minor spare parts split pin, fan body bolts, spring washer, fan rod bolt etc and PVC insulated, unsheathed stranded twin twisted copper conductor cable of size 1.5 Sqmm upto 1.0 m long, assembling the repaired ceiling fan in existing position and testing to the entire satisfication of Engineer-in-Charge on site. Notes: - (i) Replacement of spares flexible wire etc / rewinding of ceiling fan / capacitor with clamps shall be measured and paid separately under respective item for material and labour cost. (ii) Burnout winding ceiling fans will be taken out for repair / rewinding.

Description same as per Ser item No. 101.00 here-in-before but for exhaust fan of any type mm sweep complete all as specified and as directed.

Description same as per Ser item No. 101.00 here-in-before but for wall mounting fan of any size / type complete all as specified and as directed. Note: - Burnout winding exhaust fans / Wall fans will be taken out for repair / rewinding.

Rewinding of ceiling fan, of any make / type and size (1200 / 1400 mm sweep) with super enamelled copper wire of appropriate gauge as existing to obtain the specified and satisfactory RPM as per manufacturer's specification, including replacement of all insulation materials, varnishing, heating, drying, assembling of stator / rotor, connection and testing complete all as specified and as directed.

Description same as per Ser item No. 104.00 here-in-before but for exhaust fan of any make / type and size complete all as specified and as directed.

Description same as per Ser item No. 104.00 here-in-before but for wall mounting fan of any make / type and size complete all as specified and as directed.

Labour for remetalling of worn out shaft of fan, cutting, brazing, machining and polishing to make the shaft suitable for fixing of new ball bearing and fixing ball bearing in replacement of bushing system in ceiling fan and assembling the same and testing to the entire satisfaction of Engineer-in-Charge to ensure smooth and noise free operation complete all as specified and as directed. Note: - Bearing shall be measured and paid separately.

Supply and fixing ball bearing of any size and type, suitable for any type / make / size of ceiling fan complete all as specified and as directed.

Description same as per Ser item No. 108.00 here-in-before but for exhaust fan of any type / make and size complete all as specified and as directed.

Description same as per Ser item No. 108.00 here-in-before but for wall mounted fan of any type / make and size complete all as specified and as directed.

Supply and fixing in replacement of capacitor 230 Volt AC 50 Hz, conforming to IS-1709 and rated capacity 2.5 MFD for ceiling fan, exhaust fan and wall mounted fan complete all as specified and as directed.

Supply and fixing in replacement of capacitor 230 Volt AC 50 Hz, conforming to IS-1709 and rated capacity 4.0 MFD for ceiling fan, exhaust fan and wall mounted fan complete all as specified and as directed.

Supply and connection in replacement of PVC insulated, unsheathed multistranded, three core twisted copper flexible cable of size 1.5 Sqmm as required complete all as specified and as directed.

Supply and fixing in replacement of only bush of suitable size for exhaust fan of any type / size as per existing type complete all as specified and as directed.

Description same as per Ser item No. 114.00 here-in-before but suitable for wall mounted fan of any type / size as per existing type complete all as specified and as directed.

Supply and fixing in replacement of PVC connector 4 way 6 Amps with connection screws, nuts complete all as specified and as directed.

Supply and fixing in replacement of PVC clamps with fixing screws for holding capacitor of any type and size complete all as specified and as directed.

Supply and fixing in replacement of galvanised iron / mild steel anodized bolts with anodized nuts, spring washers, split pin etc size 50 mm long 10 mm dia half threaded type with split pin hole complete all as specified and as directed.

Supply and fixing in replacement mild steel clamp for down rod of suitable size including gromet / reel type rubber pad with bolts, nuts, split pin and washers suitable for housing ceiling fan complete all as specified and as directed.

Supply and fixing in replacement of ceiling fan down rod 12 mm dia and 30 / 45 cm long complete with mild steel clamp rubber reel, split pin nut bolts etc complete all as specified and as directed.

Supply and fixing in replacement of louver shutter made of mild steel sheet metal 1.2 mm thick for round base and 0.8 mm thick for flaps, comprising of mounting legs frames made of mild steel flat strips of size 25mm x 3mm including heavy duty rust proof passivated bolts of size 50 mm long 8 mm dia to be fixed on wall at ground / first / second floor etc complete with using fastener bolt, drilling, (spray painting) over a coat of primer for exhaust fan upto 400 mm sweep including taking down old one complete all as specified and as directed. Notes: - (i) Rates are deemed to be including charges for hiring any type of T&P, Ladder, cutter etc. (ii) Contractor shall be responsible for life cover of staff deployed for fixing of lover shutter.

Cleaning of ceiling fan assembly of any type / size and carrying out two coats of spray painting with first quality synthetic enamelled paint of approved colour, including writing of MES number in black paint complete all as specified and as directed.

Description same as per Ser item No. 122.00 here-in-before but for exhaust fan upto 450 mm complete all as specified and as directed.

Supply and fixing in replacement PVC canopy set of two pieces for ceiling fans of any size complete all as specified and as directed.

Repair to oscillation moving part of wall mounted fan including replacement of all wornout components, bearing, lubrication and assembling complete all as specified and as directed.

Supply and fixing in replacement of ceiling fan blades set of 3 pieces suitable for 1200 / 1400 mm sweep of white / brown / ivory colors complete all as specified and as directed.

Taking down and strip opening to geyser of any make and capacity 25 / 35 / 50 litres including disconnection of all water pipe connection and taking out water inlet / outlet assembly, removing glass wool, the inner tank, descaling the assembly and tank, detecting the leakage, welding / brazing the defected part, repacking the glass wool and refixing the same after making it functional including replacement of worn out nuts, bolts, washer etc complete all as specified and directed. Note: - Cost of material and labour for providing new items shall be measured under relevant items of sch 'A'.

Material and labour for replacement of water inlet and outlet geyser assembly of existing make as required at site with rubber gasket suitable for geyser of 25 / 35 litres capacity electric driven water storage heater with provision of housing for thermostat assembly, heating element fixing arrangement nuts, bolts and washers etc. complete all as specified and directed.

Material and labour for replacement of water inlet and outlet assembly of existing make as required at site with rubber gasket suitable for geyser of 50 litres capacity electric driven water storage heater with provision of housing for thermostat assembly, heating element fixing arrangement nuts, bolts and washers etc. complete all as specified and directed.

Material and labour for replacement of geyser internal assembly (flanged) comprising complete with heating element and thermostat housing as per site requirement and suitable with the existing assembly suitable to 25 / 50 litres capacity complete all as specified and as directed.

Material and labour for replacement thermostat capillary type switch for electric water heater storage type of capacity 25 / 50 litre, 230 volts of existing make of geyser complete all as specified and as directed.

Material and labour for replacement thermostat, switch electric water heater storage type of capacity 25 / 50 litre, 230 volts of existing make of geyser complete all as specified and as directed.

Material and labour for replacement heating element with triangular base / round base, single phase, 230 volt, capacity 2 KW of existing make complete all as specified and as directed.

Material and labour for replacement heating element with triangular / round base, single phase, 230 volt, capacity 1.5 KW of existing make complete all as specified and as directed.

Material and labour for replacement pressure release valve conforming to relevant IS 15mm bore suitable for fixing with GI pipe / tubing 15mm bore complete all as specified and directed.

Material and labour for replacement of heavy duty PVC connection (For Hot Water) nylon threaded 450mm large (18”) 15mm bore including brass nuts, rubber washers complete on both ends all as specified and as directed.

Material and labour for replacement of heavy duty PVC connection (For cold Water) nylon threaded 450mm large (18”) 15mm bore including brass nuts, rubber washers complete on both ends all as specified and as directed.

Material and labour for replacement of indicator lamps round / rectangular type 230 volt AC suitable for geyser of any capacity including providing electric connections complete all as specified and as directed.

Supply and fixing in replacement of unserviceable Geyser with metal body water heater storage type (Geyser) 25 Litre capacity, confirming to ISI, single phase with working voltage 240 Volts, 50 Hz complete all as specified and directed.

Material and labour for replacement water storage inner tank of stainless steel heavy duty confirming to ISI 25 / 35 litres capacity geyser, with provision for fixing 15mm dia galvanized air release valve complete all as specified and directed.

Material and labour for replacement water storage inner tank of stainless steel heavy duty confirming to ISI 50 litres capacity geyser, with provision for fixing 15mm dia galvanized air release valve all as specified and directed.

Material and labour for painting of geyser of capacity 25 / 35 / 50 litre complete with superior quality synthetic enamel white paint by spray painting after scrapping old paint and making surface clean all as specified and directed.

Material and labour for replacement non return valve 15 mm dia complete all as specified and directed.

Material and labour for replacement split bottom cover (two pieces) suitable for 25 to 50 litres geysers complete with fixing arrangement etc as required at site complete all as specified and as directed.

Material and labour for replacement rubber gasket heavy duty of water inlet outlet assembly suitable for 25 litres capacity geyser complete all as specified and as directed.

Material and labour for replacement outer shell suitable for 25 / 35 litre geyser made out of GI sheet heavy duly confirming to ISI suitable for existing make of geyser complete factory manufactured painted complete all as specified and as directed.

Material and labour for replacement outer shell suitable for 50 litre geyser made out of GI sheet heavy duly confirming to ISI suitable for existing make of geyser complete factory manufactured painted complete all as specified and as directed.

Supply and fixing in replacement glass wool suitable for each geysers complete all as specified and as directed.

Repair / maintenance / servicing to solar water heater system having a capacity 100 to 500 LPD complete with descaling / cleaning to flat plate collector plate, solar heater water tanks, toughened solar glass panels, welding / breazing to solar tanks, repair / rectification of leakage in inlet / outlet water tubing GI, checking and repair to electric system, repair of water make up tank and make the system functionable after repair / servicing and rectification of the fault complete with and including repacement of minor spare parts complete all as specified and as directed. Note: - Spare shall be measured and paid separately.

Supply only union medium grade 25 mm dia

Supply only union medium grade 20 mm dia

Supply only Rubber hose pipe with MS clamp of suitable size

Supply only Gun metal gate/glove valve 20 mm dia

Supply only Rubber gasket of toughened glass

Supply only Painting to steel structure base frame

Supply only float valve PVC 20 mm dia

Material and labour for replacement of Electrical heating element long threaded type, as per existing 3 KW, ISI marked, single phase suitable for solar water heater complete all as specified and directed.

Material and labour for replacement of thermostat, long body, ISI marked of solar water heater of capacity 100 to 500 LPD complete all as specified and as directed.

Material and labour for replacement of Solar hot water tank with thermal insulation suitable for solar water heater of capacity 100 LPD complete all as specified and as directed.

Material and labour for replacement of Solar hot water tank with thermal insulation suitable for solar water heater of capacity 500 LPD complete all as specified and as directed.

Material and labour for replacement of toughened collector glass of size 1.5 M x 1.0 Mtr complete all as specified and directed confirming to ISI.

Material and labour in replacement for fasteners 80-100 mm long for fixing of geyser of capacity upto 50 litres including grouting completed works in wall as per site requirement with the floor complete all as specified and directed.

Supply and fixing in replacement chromium plated CP Bib cock 15 mm dia conforming to ISI complete all as specified and as directed.

Supply and fixing in replacement Gun metal glove / gate valve 15 mm dia internal threaded with iron wheel head conforming to ISI complete all as specified and as directed.

Material and labour for replacement of hot water pipe insulation with glass wool and aluminium cladding 20mm bore including all materials as required and directed by Engineer-in-Charge.

Supply and fixing in replacement of sheet metal enclosure for MCB DB SPN 240 Volts, 2 way single door without bus bar, enclosure made up of CRCA sheet IP-30 including wooden rectangular board of first quality of suitable size for mounting of DB box complete all as specified and directed by Engineer-in-Charge.

Material and labour in replacement for sub main wiring with proper colour coding, insulated, unsheathed, multistranded, copper conductor FRLS, cable of 2 run 4 Sqmm for phase and neutral and one run of 2.5 Sqmm for earth wire unsheathed, multistranded, copper conductor FRLS, drawn in but including non metallic rigid PVC concealed conduit of 25 mm dia fixed on wall. Two runs of cable for phase / neutral and one run of cable for earth will be measured and paid as one unit length. Note: - Wiring shall be done in proper colour coding.

Material and labour for replacement of tubing galvanised iron "medium grade" with all fittings laid in floor or trenches including taking out old unserviceable pipe of size 15 mm dia complete all as specified and directed.

Material and labour for repair / maint to desert coolers complete with and including cleaning, scrapping / rubbing old rusted surface, filling cavities and painting with two coats of high quality aluminium paint externally and black paint to water storage tank internally with synthetic enamelled paints complete with replacement of necessary nut, bolts, rubber pads for fan motors and writing MES No / unit name complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing in replacement of desert cooler fan motor 90 watt, 1400 RPM, 230 Volt, 50 Hz single phase conforming to ISI complete with fan blade and capacitor of sutitable size complete all as specified and as directed.

Supply and fixing in replacement of desert cooler submersible pumping set single phase 230 Volt, 50 Hz of 0.25 to 1.0 HP conforming to ISI complete with lead complete all as specified and as directed.

Supply and fixing in replacement of PVC accessories of desert cooler i.e. PVC pipe 20 mm dia heavy duty 2 metre approximate, PVC distributor 4 way with nut, bolts, PVC elbow-03 No's, mild steel clamps etc complete all as specified and as directed.

Supply and fixing in replacement of desert cooler fan motor blade of existing size made out from mild steel having duty complete with key bolt complete all as specified and as directed.

Supply and fixing in replacement of desert cooler side opening cover made out from heavy duty mild steel sheet and matching with the existing desert cooler body size complete with Khas Khas pads set of three pieces complete all as specified and as directed.

Supply and fixing in replacement of desert cooler unserviceable / leakage body made out from heavy duty mild steel sheet bend to shape company manufacturer, complete with internal PVC accessories i.e. PVC elbow-03 No's, PVC distributor 4 way-01 No, PVC distribution pipe - 2 metre approximate, black painted internally, Aluminium painted externally complete with provision of necessary arrangement for fixing front cover and fan motor complete all as specified and as directed.

Supply and fixing in replacement cable PVC insulated and sheathed of size 1.5 Sqmm 3 core FRLS, 230 Volt, 50 Hz conforming to ISI complete all as specified and as directed.

Supply and fixing in replacement cable PVC insulated and sheathed of size 2.5 Sqmm 3 core FRLS, 230 volt, 50 Hz conforming to ISI complete all as specified and as directed.

Supply and fixing in replacement cable PVC insulated and sheathed of size 4.0 Sqmm 3 core FRLS, 230 volt, 50 Hz conforming to ISI complete all as specified and directed.

Supply and fixing in replacement of plug top 3 pin, 5 Amp, 230 Volt, 50 Hz complete all as specified and as directed.

Material and labour in replacement for fabrication of desert cooler stand made out from angle iron 40 X 40 X 6mm thick, bend to shape, welding as per site requirement fixing in brick / stone masonary wall complete with cemented work necessary rawl plug, nut, bolts etc complete all as specified and as directed.

Supply and fixing in replacement of PVC accessories of capacitor 2.5 MFD for desert cooler fan motor, 230 Volt 50 Hz complete all as specified and as directed.

Supply and fixing in replacement of unserviceable Khas Khas / Glass wool for desert cooler set of three pieces complete all as specified and as directed.

Repair / maint / servicing to refrigerator / deep freezer / water coolers / AC's of any capacity and model by replacing capillary tubing, gas chargings, rectification of leakage in capillary tubing / Chiller plant / water tanks, condensing coils, repair to wiring, flushing / cleaning, condensing / cooling coils / internal / external unit of split AC, greasing to blower motors, replacement of spare parts, fan belts and make refrigerator / deep freezer / water coolers / AC's in serviceable condition complete all as specified and as directed by Engineer-in-Charge. Note: - Spare / Gas charging shall be paid separately.

Charges for fixing in replacement of unserviceable sealed seamless welding compressor unit company manufacturer of any capacity for AC's complete with initial filling / charging of refrigerant gas to meet the requirement complete with vibration rubber pads four no's each nut, bolts etc and testing on full load all as specified and directed by Engineer-in-Charge. Notes: - (i) Spare parts shall be measured and paid separately under respective items. (ii) Contractor shall be responsible for all replacement of failed compressor and shall be accompanied by certificate from the original compressor to the effect that said compressor has been repaired at their authorised service center. Further, a warranty of 12 months shall be provided on such replacement in writing.

Supply only sealed compressor unit seamless welding company manufacturer with filling of refrigerant gas conforming to ISI as under: -

For refrigerator 165 / 286 Litre capacity.

For refrigerator 290 / 320 Litre capacity.

For Deep Freezer 100 / 200 Litre capacity.

For Deep Freezer 300 / 400 Litre capacity.

For Water Cooler 40 / 80 Litre capacity.

For Water Cooler 60 / 120 Litre capacity.

Split / Window AC 1.5 Ton capacity.

Supply and fixing in replacement of unserviceable / burnt condensing fan motor 1/35 HP single phase 230 Volt 50 Hz complete with blade, fan belts for water cooler of capacity 40 / 80 Litre and 60 / 120 litre complete all as specified and as directed.

Supply and fixing in replacement of condensing fan motor 1/5 HP 1440 RPM single phase 230 Volt 50 Hz with double blade and shaft end with fan belts for windows AC / split AC conforming to ISI of capacity 1.5 / 2.0 ton complete with vibration parts etc complete all as specified and as directed.

Supply and charging refrigerant 134a/R-22 in sealed compressor unit of refrigerator / deep freezer / water coolers / AC's of any type and capacity after flushing the complete system with carbon tetrachloride (CTC) and vacuumise the complete system with vacuum pump and testing on full load including replacement of filter, strainer complete all as specified and as directed.

Supply and fixing in replacement of following spare parts for refrigerator / deep freezer / water coolers / AC's of any capacity: -

Starting relay

Overload protector

Thermostat switch

Defroz switch

Supply and fixing in replacement of following unserviceable spare parts of water cooler of any capacity: -

Starting capacitor 45 mfd

Running capacitor 60/120 mfd

Float valve PVC 15 mm dia with ball

Push cock chromium plated 15 mm with nipple 6'' long

Drain/Wash out flexible down pipe 40 mm dia

Water tank door gasket

Water drain tray of suitable size

Supply and fixing in replacement of unserviceable following spare parts of window / split AC unit of capacity 1.5 to 2.0 ton: -

Starting capacitor 36/40 mfd

Running capacitor 100/120 mfd

PCB of Split AC

Front Grill cover for window AC 1.5 Ton

Condensing fan motor double shaft

Supply and fixing in replacement of PVC flexible braided pipe of 20 mm dia for split AC water drain out complete all as specified and as directed.

Supply and fixing in replacement of outer split AC condensing unit complete for split AC 1.5 ton all as specified and directed.

Supply and fixing in replacement of inner unit of split AC complete with filters, blower motor etc for split AC 1.5 ton complete with all accessories all as specified and directed.

Supply and fixing in replacement of copper capillary tubing 5/8'' for AC connection / repair complete all as specified and as directed.

Supply and fixing in replacement of condensing unit of Refrigerator / Deep Freezer / water cooler of any capacity complete with cutting and brazzing work complete all as specified and as directed.

Supply and fixing in replacement of magnetic door gasket of refrigerator 165 to 310 Litres capacity complete all as specified and as directed.

Supply and fixing in replacement of freezer compartment (Chiller Unit) with dooe / cover of refrigerator 165 to 310 Litres capacity of any make complete all as specified and as directed.

Supply and fixing in replacement of chiller tray of approved quality / brand suitable for upto 310 Litres capacity of any make complete all as specified and as directed.

Supply and fixing in replacement of vegetable / fruit basket with lid of approved quality / brand suitable for upto 310 Litres capacity of any make complete all as specified and as directed.

Material and labour for preparation of old steel surface by using wire brush / emery paper etc and make the surface smooth and paint to the outer cover / external surface of water cooler with two coats of synthetic enamel paint and re-writing the MES NO etc to water cooler of any capacity complete all as specified and as directed.

Supply and fixing in replacement of 1100 Volts grade heavy duty cable PVC insulated aluminium conductor, served with inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than 1 metre apart including 4mm suspension wire, one 10 Sqmm twin core stranded conductor cable flat or circular complete all as specified and as directed.

Supply and installation for replacement of automatic voltage stabilizer with back boost relay working range 90 to 290 Volt at 230 Volt of capacity 5 KVA complete all as specified and as directed.

Supply and installation for replacement of automatic voltage stabilizer with back boost relay working range 90 to 290 Volt at 230 Volt of capacity 3 KVA complete all as specified and as directed.

Supply and installation for replacement of automatic voltage stabilizer with back boost relay working range 90 to 290 Volt at 230 Volt of capacity 2 KVA complete all as specified and as directed.

Supply and installation for replacement of automatic voltage stabiliser with back boost relay working range 90 to 290 Volt at 230 Volt of capacity 1 KVA complete all as specified and as directed.

Labour for disconnecting all incoming / outgoing electric connection carefully of fully automatic servo voltage stabilizer having capacity 30 to 200 KVA and transport to workshop for repair / servicing and including dismantling top cover of stabilizer and taking out the coil, drain out the transformer oil and refilling after dehydration of transformer oil, cleaning internally, including replacement of unserviceable body nut, bolts, washers, top gasket of cork sheet 6mm thick, replacement of internal circuit wiring if any suitable size of copper wire and painting with heat resistant smoke grey / as per existing colour synthetic enamelled paint including preparation of old rusted surfaces and writing MES NO, SM MES No, capacity, Ser No, Location etc and reinstallation / connecting electric connection with replacement of proper size aluminium lugs and testing on full load at site complete all as specified and as directed. Notes: - (a) Spare parts shall be measured and paid separately. (b) Rotor for replacement of spare parts are deemed to be included in above jobs.

Supply and fixing in replacement synchronous motor single phase 230 Volt suitable for servo voltage stabilizer having capacity 30 to 200 KVA complete all as specified and as directed.

Supply and fixing in replacement PCB suitable for servo voltage stabilizer having capacity 30 to 200 KVA complete all as specified and as directed.

Supply and fixing in replacement dimmer motor suitable for servo voltage stabilizer capacity 30 to 200 KVA complete all as specified and as directed.

Supply and fixing in replacement copper dimmer suitable for servo voltage stabilizer capacity 30 to 200 KVA complete all as specified and as directed.

Supply and fixing in replacement toggle On / Off switches for stabilizer capacity 30 to 200 KVA complete all as specified and as directed.

Supply and fixing in replacement Volt meter 0-500 Amp, 96mm Square type, 3 phase, 230 Volt 50 Hz complete all as specified and as directed.

Supply and fixing in replacement Ampere meter 0-400 Amp, 96mm Square type, 3 phase, 230 Volt 50 Hz with CT of suitable ratio complete all as specified and as directed.

Supply and fixing in replacement gun metal gate or glove valve 20 mm for drain out of oil complete all as specified and as directed.

Supply and fixing in replacement unserviceable brass / gun metal stud bush suitable for 30 to 200 KVA complete with connecting rod of suitable length and dia with necessary nut, bolt, washer, bushing packing to prevent the leakage from bushes and necessary connection complete all as specified and as directed.

Dehydration of Transformer oil and dielectric strength of oil achieved not to be less than 42 KV at 2.4 mm gap complete all as specified and as directed.

Supply and filling of new transformer oil for top up upto automatic servo voltage stabilizer including heating and dielectric strength not to be less than 60 KV complete all as specified and as directed.

Taking out main coil of voltage stabilizer 30 to 200 KVA for repair / rewinding with super enamelled copper winding wire of existing gauge including PVC insulated sheet sleeve, varnishing etc all as required and refixing to the stabilizer after testing all as required at site or directed by Engineer-in-Charge.

Supply and fixing in replacement of ground burial 3 watt light with transparent tempered glass diffuser with working voltage 90 V - 260 V AC complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing in replacement of slim flood light 100 watt warm yellow including in-built surge protection as per requirement LED flood light fittings along with IP-65 protection all as specified and as directed.

Supply and fixing in replacement of slim flood light 200 watt warm yellow including in-built surge protection as per requirement LED flood light fittings along with IP-65 protection all as specified and as directed.

Supply and fixing in replacement of XLPE insulated screened PVC bedded, galvanised steel strip or wire armoured electric power cable (heavy duty) 1100 Volt grade with stranded aluminium conductor of size 25 Sqmm 3½ core complete all as specified and as directed.

Supply and fixing in replacement of XLPE insulated screened PVC bedded, galvanised steel strip or wire armoured electric power cable (heavy duty) 1100 Volt grade with stranded aluminium conductor of size 10 Sqmm 2 core complete all as specified and as directed.

Excavation in trenches not exceeding 1.5 metre wide and not exceeding 1.5 metre deep for foundations of poles / stays / cable etc. and getting out in soft / loose soil complete all as specified and as directed by Engineer-in-Charge.

Returning, filling in, earth including spreading, levelling, watering and well ramming in layers each not exceeding 25 cm thick each layer complete all as specified and as directed.

Removing of surplus soil to a distance not exceeding 50 metre and depositing where directed at a level not exceeding 1.5 metre above the starting point complete all as specified and as directed by Engineer-in-Charge.

Material and labour for sand cushioning with a layer of fine sand (sand for plastering) 8 cm thick before laying of cable and 15 cm thick after laying of cable in trenches and ducts in installation complete all as specified and as directed.

Supply and laying including taking out old one well burnt old size sub class 'B' bricks laid flat with width equal to length of brick perpendicular to the direction of cable, adjacent / abutting each other complete all as specified and as directed by Engineer-in-Charge in trenches over the cable for protection.

NOTE NO 1: - Samples of materials as approved will be kept in GE's sample room. NOTE NO 2: - All fittings and fixtures mentioned above will be fixed to the satisfaction of Engr-in-Charge and GE. NOTE NO 3: - Warranty certificate to the Engineer-in-Charge where ever applicable shall be submitted by the Contractor at the time of fittings.

M/s Sahib Construction and engineers