PROVN OF DRAIN COVERS IN 5 MARATHA LI AND SPL REPAIR OF REWIRING OR INTERNAL ELECTRIC SUPPLY IN BLDG NO P-37 OFFICE COMPLEX OF 12 GASL UNDER GE (SOUTH) DELHI CANTT-10

Amount

Taking down carefully the old U/S aluminum/Copper point wiring (light, fan, socket or power) complete fitting such as switches, ceiling roses, pendants, sockets, regulators, call bell etc and making good disturbed surfaces of walls including necessary touch up with the adjoining surface of disturbed area ie with OBD/colour wash/white wash as the existing finish complete all as specified and directed by Engineer-in-charge

M&L for point wiring complete with single core multi strand copper conductor 1.5 Sqmm nominal area PVC insulated FRLS 1100 Volts grade electrical cable in and including concealed PVC conduit medium grade and sunk in new pressed steel terminal boxes of required size factory made and factory painted with stove enameled black paint with top cover 3 mm thick plastic/laminated sheet (ISI Marked) of required color with screwed and cup washer with all accessories including 1.5 Sqmm single core with multi strand copper conductor PVC unsheathed cable earth and connected to earth dolly complete for One light /fan/Bell point controlled by one way switch all as specified and directed by Engr-in-Charge Note:- The rate is inclusive cutting /chasing and making good the disturbed surface with cm 1:3 and same surface finishes with the adjoining surface of disturbed area with OBD/colour wash/white wash.

All as per above Ser item No. 2 but here-in-before one 3 pin 5 Amps socket outlet point controlled by one No one way switch on independent board.

All as per above Ser item No. 2 but here-in-before one 3 pin 5 Amps socket outlet point controlled by one No one way switch on same board.

All same as per item No 2 but here-in-before point wiring with 2.5 Sqmm single core copper cable and earth continuity wire with 1.5 Sqmm single core cable for one three pin 15 Amp socket outlet point on independent board.

All same as per item No 2 but here-in-before one 3 pin socket outlet, 15 amps on independent board with cable 4 Sqmm for main current and 2.5 sqmm as earth wire as power point

S&F switch piano flush type 5/6 Amp one way single pole complete all as specified and directed by Engineer-in-charge

S&F socket outlet 5 pin 5/6 Amp two in one complete all as specified and directed by Engineer-in-charge

S&F switch piano flush type 15 Amp complete all as specified and directed by Engineer-in-charge

S&F socket outlet 2 in 1, 5 pin 15/5 Amp complete all as specified and directed by Engineer-in-charge

S&F ceiling rose surfaces bakelite minimum size 65x50mm with two/ three terminals complete all as specified and directed by Engineer-in-charge

S&F Metal clad plug and socket 20 Amps with MCB SP and steel enclosure complete all as specified and directed by Engineer-in-charge

M&L for bell push flush button single pole one way 5 Amps 240 volts complete all as specified and directed by Engineer-in-charge Make:- Cat Part No. 1026 of Cona or its equivalent as specified make

M&L for bell electric heavy duty Ding Dong type230 volts single pole complete all as specified and directed by Engineer-in-charge Make:- Cat part No 22535 of Anchor, No : 2856 of Cona or its equivalent as specified make

S&F of LED of Integrated Batten T5 20 watt - 4 Ft White, indoor decorative PVC extruded T5 LED battern -integrated type with including fliexble wire in replacement of old unsv existing 36 Watt tube light fitting complete all as specified and directed by Engineer-in-charge. Make:- Cat Part No LTTB4F20LEDP/W of C&S or its equivalent as specified make

S&F Surface/Recessed mounting 34 Watt (VENUS NEO-857) 2'x2' LED panel fitting, Ultra modern designed architectural LED luminaire which provides soft-light and glare free symmetrical illumination suitable for Armstrong/Grid ceiling in replacement of old unsv existing CFL fitting any type from ceiling of stairs/common areas and making good a disturbed surface/armstrong ceiling to match with armstrong ceiling and getting electrically connected the fitting with switch board for suitable size of PVC copper wire complete all as specified and directed by Engineer-in-charge. Make : Havells Cat Part No (Model) LHEWDRP7PK1W034 or its equivalent in Bajaj/Philips/C&S/Havells.

S&F Recessed Mounting (Pluto 2x2-857) 34 Watt 2'x2' flat LED panel fitting with soft light and glare free symetrical ilumination suitable for POP ceiling supplied with wedge bracket to fix in existing POP ceiling including cutting/grouting of existing POP ceiling in replacement of existing old unserviceable CFL fitting any type from ceiing of stairs/common areas and making good a disturbed surface/POP ceiling to match with POP and getting electrically connected the fitting with switch board for suitable size of PVC copper wire complete all as specified and directed by Engineer-in-charge. Make : Havells of Cat Part No (Model) - LHEWEIP7PW1W034 or its equivalent in Bajaj/Philips/C&S/Havells.

S&F in replacement LED Building security light fitting 45 Watt including necessary electrical connection from bottom/middle of the wall to security light fitting in conclealed with PVC conduit complete all as specified and directed by Engineer-in-charge Make:- Cat Part No LTESSE45WLED of C&S or its equivalent as Bajaj/Halonix/Philips/CG.

S&F LED Integrated Batten aesthetically designed linear mirror LED light fitting of 07 Watt 1' white, indoor decorative PVC extruded provided with a high output PMMA diffuser for glare free light LED battern integrated type with including fliexble wire in replacement of old unsv existing any type mirror light normal fitting complete all as specified and directed by Engineer-in-charge. Make:- Cat Part No. LCL-07-DL of CG or its equivalent as Havells/Bajaj/Philips/C&S

S&F in replacement LED 9 Watt white Bulk head in engineering plastic housing with clear prismatic including all accessories LED bulb of 12 Watt with connecting up twisted flexible copper conductor cable of suitable size of 230 V, 50 Hz complete all as specified and directed by Engineer-in-charge. Make:- Cat part No. CG80IB6WLED of C&S or its equivalent as Havells/CG/Bajaj/Philips

S&F ceiling fan regulator electronic type complete all as specified and directed by Engineer-in-charge Make : Cona/Kinjal/Havells

Taking down old unserviceable ceiling fan and exhaust fan any type complete all as specified and directed by Engineer-in-charge Note:- old unserviceable ceiling fan/exhaust fan deposited in AGE E/M store yard.

S&F ceiling fan 1200 mm sweep 5 star rated in colour of White and copper wound complete with all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size complete all as specified and directed by Engineer-in-charge Make : Cat part No. ES-50 premium of Havells or its equivalents CG/USHA/Crompton Greaves/Bajaj

S&F exhaust fan 300 mm sweep 5 star rated metal body AC 230 Volt copper wound including connecting up with twin core twisted flexible copper conductor cable with suitable size and louver complete all as specified and directed by Engineer-in-charge. Make:- Cat part No. Ventil Air DS of Havells or equivalent in USHA/Bajaj/CG

Supply and fixing in replacement MCB DB SPN 12 Way with metal double door ,(IP43 Protection) flush mounting epoxy powder control having 200 Amps rated bus bar complete all as specified and directed by Engineer-in-charge

S&F in replacement of MCB SPN 'C' curve 32/40 Amps 240 Volts ,10 KA complete all as specified and directed by Engineer-in-charge

S&F in replacement of MCB SP 'C' curve 06 to 32 Amps 240 Volts complete all as specified and directed by Engineer-in-charge

S&F in replacement of submain wiring of two runs of 6 Sqmm size for main cable and one run of 4 Sqmm size earth continuity conductor of single core PVC insulated but unsheathed FRLS cable of specified size multistranded copper conductor 1100 volts grade IS-694 marked , drawn through existing steel/PVC conceiled conduit of size 25mm dia with all fittings accessories complete all as specified and directed by Engineer-in-charge

S&F in replacement of sub main wiring PVC insulated FRLS single core multistranded copper conductor cable 2 Runs of 10 Sqmm for phase and neutral and 1 run of 6 Sqmm for earth wire drawn through existing concealed steel /PVC conduit wiring in wall not less than 25mm dia with all fittings like tees, bends, junction/terminal boxes etc as per site requirement complete all as specified and directed by Engr-in-charge Make:- Havells/Ploycab/Finolex (Note: Two runs of cable for phase/neutral and one run of cable for earth will be measured and paid as one unit length)

S&F in replacement of sheet metal enclouser MCCB DB IP 20 double door bus bar neutral link earth bar and din rail VTPN 4 way complete all as specified and directed by Engineer-in-charge Make:- Cat part No 607752 (DPX 63+12+12) of Legrand or its equivalent in C&S/Siemens/ABB.

S&F in replacement of on distribution board MCCB 63 Amps 4 pole 415 Volts 16 KA complete all as specified and directed by Engineer-in-charge

M&L for Earthing complete with galvanized steel earth plate 600x600x6mm thick, buried directly in ground (earth pit not less than 2.25 m deep below ground level) with top edge of the plate n.less than 1.5 m below normal ground level, connected to galvanized iron wire 4 mm as earthing lead by means of bolts, nuts, check nuts & washers of galvanized iron or steel besides building at all joints as shown in drgs and including excavation and earth work, GI pipe light grade 25mm bore of protection of GI wire from earth electrode, supply and laying charcoal dust, common salt, PCC (1:2:4) type B-1 Chamber and MS angle iron frame 40x40x3mm and RCC cover 40 mm thick (1:2:4) type B-1using 20 mm graded stone aggregate Reinforced with 6 mm dia round bars @ 75 mm C/C both ways with MS handle 12 mm dia , PGI funnel and wire mesh , 20 mm dia GI Pipe light grade for watering complete all as shown in SSR Part-1 (2009) plate No. 3 drg and connected to earth test point including testing complete all as specified and directed by Engineer-in-charge

S&F in replacement for Earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/pipe or fixed to poles or any other indicate dsituation for loop earthing etc. as required 4mm dia galvanised iron or steel wire complete all as specified and directed by Engineer-in-charge

Demolition of brick work built in cement mortar of any description complete all as specified and directed by Engineer-in-charge

M&L for brick work with sub class 'B' Bricks straight or curved on plan exceeding 6m mean radius built in cement mortar 1:4 as in manholes complete all as specified and directed by Engineer-in-charge

M&L for 15mm thick rendering on fair faces of brick work or concrete surfaces in CM 1:4, surface is to be finished even and smooth (without using extra cement) including one coat of primer complete all as specified and directed by Engineer-in-charge

M&L for cement concrete (1:2:4) type B1 using 20mm graded stone aggregate as in surface channels, drains (forming fair finished channel shall be measured and paid for separately) complete all as specified and directed by Engineer-in-charge

Mild steel TMT bars 10mm dia & over,cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mmdia or securing with clips complete all as specified and directed by Engineer-in-charge

All same as per item No 38 above but here-in-before 8mm dia complete all as specified and directed by Engineer-in-charge

Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls,drain cover horizontal or sloping and similar work exc 10cm but n exc 20cm wide complete all as specified and directed by Engineer-in-charge

M&L for precast reinforced cement concrete 1:2:4 type B1 using 20 mm graded stone aggregate in landings, cover slabs (for manholes etc.) chullah hoods, chajjas, shelves and similar articles with plain faces, set in CM 1:4 etc complete all as specified and directed by Engineer-in-charge (Reinforcement shall be measured and paid for separately)

M&L for PCC 1:3:6 type C-1 using 20 mm graded stone aggregate in cills, steps, bands, copings, bed plates, blocks for inserting hold fasts etc. and the like including weathering, slightly rounded or chamfered angles and throating complete all as specified and directed by Engineer-in-charge

M&L for prepation of new surface of wall drains cover and applying two coats of white wash complete all as specified and directed by Engineer-in-charge

Note:- The contract sum shall be after deducting the amount of Credit shown in Credit Schedule of this Tender.

aggarwal engineers contractors

M/S.Parmod Johar

M/s KUNDU CONSTRUCTION