SPECIAL REPAIR TO MAIN FIRE STATION BLDG NO. P-285 AND OTHER MINOR WORK OF CERTAIN UNITS AT MIL STN JAISALMER UNDER GE (A) JAISALMER

Amount

Excavating in trenches not exceeding 1.5m wide and not exceeding 1.5m in depth for foundation, laying of cable/pipe etc or for shafts, wells, cesspits, manholes, pier holes etc not exceeding 10 Sqm on plan and not exceeding 1.5 m in depth and getting out in hard/dense soil complete all as specified & directed by Engineer-in-Charge.

Returning, filling in, including, spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick with hard/dense soil complete all as specified & directed by Engineer-in-Charge.

Removing excavated soil to a distance not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified & directed by Engineer-in-Charge.

Taking down chowkats or frames n.exc 1.50 sqm each, without taking off shutters from the frames including iron mongry complete all as specified & directed by Engineer-in-charge.

Taking down chowkats or frames exc 1.50 sqm but not exceeding 4 sqm each without taking off shutters from the frames including iron mongry complete all as specified & directed by Engineer-in-charge.

Taking down shutters of any description exceeding 1.00 Sqm but not exceeding 2.00 Sqm each complete all as specified & directed by Engineer-in-charge.

Taking down shutters of any description area exceeding 2.00 Sqm each complete all as specified & directed by Engineer-in-charge.

S&F factory made steel windows with side hung shutters including projecting type hinges with steel handle and steel peg stay complete with glazing bars, dovetailed or welded all as specified & directed by Engineer-in-charge.

S&F Pressed steel door frame for doors made out of 1.2 mm thick sheet with one or more rebates incl necessary fixing lugs, hinges, lock strike plate, etc size 165x60 mm, complete all as specified & directed by Engineer-in-charge.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as specified & directed by Engineer-in-charge.

S&F 30mm thick of Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, uppling & fixing in the frame at site as per specification & drawing etc complete all as specified & directed by Engineer-in-charge.

S & F Flush shutters 20mm thick, solid core construction, with block board core and plywood face panels, commercial type on both sides one face is covered with decorative face veneer with lipping/frame to match complete all as specified & directed by Engineer-in-charge.

S&F 35 mm thick Glazed and skeleton shutters second class hard wood, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified & directed by Engineer-in-charge.

S&F, 100mm size, butt hinges, medium weight, cold rolled mild steel including necessary welding if required all as specified & directed by Engineer-in-charge.

S & F 150mm long aluminium anodized, barrel tower bolt of extruded section complete all as specified & directed by Engineer-in-charge.

S&F 300mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified & directed by Engineer-in-charge.

S & F 4.8mm thick Sheet glass, ordinary quality and glazing with oil putty in square n exc 0.50 Sqm in each pane complete all as specified & directed by Engineer-in-charge.

S&F for Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.00mm and fixed with tinned tacks, or galvanised wire staples complete all as specified & directed by Engineer-in-charge.

Demolition of reinforced cement concrete in roofs, floors, beams, staircases, landing, chajjas, facia and similar suspended work and making good the surface with 10mm thick rendering in CM 1:4 finished even and smooth with out using extra cement and removing the debris from the site, complete all as specified and directed by Engineer-in-charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premise complete all as specified and directed by Engineer-in-charge.

M&L for 25mm thick PCC (1:2:4) type B0 (using 12.5mm graded stone aggregate) as in subbase of floors & finishing the surface even & smooth without using extra cement complete all as specified and directed by Engineer-in-charge.

M & L Non - skid Ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with the colour of tiles laid over and including 15mm thick screed bed or bedding in cement mortar 1:6 complete all as specified and directed by Engineer-in-charge.

M&L for Glazed ceramic coloured tiles 350x250x7mm/450x350x7mm thick in vertical surfaces etc set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 10mm thick screed in CM 1:4 complete all as specified and directed by Engineer-in-charge.

M&L Non skid ceramic coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with the colour of tiles laid over and including 15mm thick screed bed in cement mortar 1:6 complete all as specified and directed by Engineer-in-charge.

S & F Providing & fixing false ceiling at all heights with GRG (Glass Fibre Reinforced Gypsum) with semi perforated 12 mm thick tegular edged GRG false ceiling tiles of size 595 x 595 mm of approved texture, design and patterns having moisture content less than 2%, humidity resistance 99%, NRC0.50 to 0.75 as per IS 8225:1987, Noncombustible as per BS 76 (part 4 )-1970 and light reflectance of 85% (minimum) to be laid in true horizontal level suspended on interlocking metal T-Grid of hot dipped galvanized iron section of 0.33mm thick (galvanized @ 120 grams per sqm including both sides) comprising of main- T runners of size 15 x 32 mm of length 3000mm,cross-T of size 15x 32mm of length 1200mm and secondary intermediate cross-T of size 15 x 32 mm of length 600mm to form grid module of s1ze 600x 600mm,

ITEM NO. 25.00 CONTD... suspended from ceiling using galvanized mild steel items (galvanizing @ 80 grams per sqm) i.e 50mm long, 8mm outer diameter M-6 dash fasteners, 6mm dia fully threaded hanger rod upto 1000mm length and Lshape level adjuster of size 85x25x2mm. Galvanised iron perimeter wall angle of size 24x 24x0.40mm of length 3000 mm to be fixed on periphery wall I partition with the help of plastic rawl plugs at 450 mm center to center and 40mm long dry wall wood screws. The work shall be carried out as per specifications, drawing complete all as specified and directed by Engineer-in-charge.

Demolition of concrete in ground floors and pavings exc 15 cm thickness complete all as specified and directed by Engineer-in-charge.

M&L for 75 mm thick cement concrete (1:4:8) type D-2 (using 40 mm graded stone aggregate) as in sub base of flooring/ hard standing & finished the surface even & fair without using extra cement complete all as specified and directed by Engineer-in-charge.

Taking down cement plaster of any description on stone or brick walls etc including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed by Engineer-in-charge.

M&L for 10mm thick rendering in cement mortar 1:4 on fair face of stone masonry surfaces, finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-charge.

M&L for rendering 15mm thick on stone surfaces or other than fair faces of brick work or on one side of lathing in cement mortor 1:6, finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-charge.

M&L for rendering 5 mm thick in CM (1:3) on fair faces of concrete surfaces as in ceiling finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-charge.

M&L for preparing new plastered or unplastered surfaces and applying three coats of white wash on ceiling all as specified & directed by Engineer-in-charge.

M&L for preparation of new plastered surfaces of walls and applying two coats of distempering oil emulsion over a coat of primer complete all as specified & directed by Engineer-in-charge.

M&L for prepration of new plastered wall surfaces of any description over 10cm girth or width, not otherwise described and applying two coat of weather proof paint over a priming paints plaster coat , complete all as specified and directed by Engineer-in-charge.

Demolition of cement concrete (un reinforced) in ground floors and pavings n.exc 15 cm thick (below or above ground level) & removing rubbish out side MD land complete all as specified and directed by Engineer-in-charge.

M&L for 100mm thick PCC (1:2:4) type B-1 (using 20mm graded stone aggregate), as in hard standing finished even & smooth without using extra cemen complete all as specified and directed by Engineer-in-charge.

M&L 75 mm thick PCC (1:3:6), type C1 (using 20mm graded stone aggregate) in plinth protection and path laid in alternative bays finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-charge.

S&F in repair, tubular towel rail brass chromium plated, 20mm dia, D type, 60cm long between flanges fixed with chromium plated brass screws complete all as specified & directed by Engineer-in-charge.

S&F in repairs, harrison rails, mild steel, chromium plated with fixing brackets, stops, rollers etc complete all as specified & directed by Engineer-in-charge.

M&L for preparing new or previously untreated wood and wood based surfaces of any description otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint (Ordinary tint) over a coat of pink primer complete all as specified & directed by Engineer-in-charge.

M&L for preparation of new or previously untreated steel surface of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint (ordinary tint) over a coat of red- oxide, zinc chrome primer complete all as specified & directed by Engineer-in-charge.

Supplying and laying of 16mm outer dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings in trenches/wall including taking down existing pipe of any description complete all as specified & directed by Engineer-in-charge.

Supplying and laying of 20mm outer dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings in trenches/wall including taking down existing pipe of any description complete all as specified & directed by Engineer-in-charge.

S&F in repairs 15mm dia Bib taps cast copper alloy chromium plated with crown or capstan head, screwed down, high pressure screwed for iron pipe complete all as specified & directed by Engineer-in-charge.

S&F in repair, Vitreous china wash basin pedestal type, white, flat back, size 550 X 400 mm excluding taps, chain and plug and porcelain stopper but including CP waste coupling & brackets and fixed complete all as specified & directed by Engineer-in-charge.

S&F in repair Brass CP wall mixer of 15mm dia bore for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified & directed by Engineer-in-charge.

S&F in repairs 15mm dia Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified & directed by Engineer-in-charge.

S&F in repairs brass chromium plated shower rose with swivel joints 125mm dia with 18mm dia chromium plated pipe complete all as specified & directed by Engineer-in-charge.

S&F in repair 20 mm bore gun metal globe or gate valve, with iron wheel head, screwed both ends for iron pipe complete all as specified & directed by Engineer-in-charge.

S&F 1000 ltrs capacity white colour three layer rotational moulded polythene water storage tank (Cylinderical vertical with closed top) hoisted and fixed in position with 20mm bore dia ball brass valves high pressure, with polythene float and flynut screwed for iron pipe or brass ferrule including dismantling of existing tank with float valve complete all as specified & directed by Engineer-in-charge.

S&F in repair vitreous china wash down water closet pedestal pattern including connecting to flush tank, complete all as specified & directed by Engineer-in-charge.

S&F in repair, health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified & directed by Engineer-in-charge.

S&F in repairs 10 ltrs capacity PVC low level flushing cistern with inlet, ball valve, float, handle including fitting and fixtures and taking down the old damaged cisterns and providing connections to WC and flush pipe without any damage to the existing fittings complete all as specified & directed by Engineer-in-charge.

M & L for 150mm bore dia reinforced cement concrete pipes, class NP2, laid and jointed with collars complete all as specified and directed by Engr-in-Charge. (Note :- Excavation and earth work shall be measured and paid separately.

M&L for PCC (1:3:6) type C-2 (using 40mm graded stone aggregate) for concrete bed to drain pipes including packing under and haunching against the sides of pipe after they are laid and tested for 150mm bore pipe including demolition of existing concrete bed, haunching and breaking up drain pipe of any desription complete all as specified & directed by Engineer-in-charge.

S&F 5cm thick sand stone slabs Jaisalmer pattern/colour in sun-shades, chajjas, shelves, cills, landings, cover stones, templates, etc not exceeding 2m in length, punched dressed on face and along exposed edges, self faced on other side and set and pointed in cement mortar (1:4) including demolition of existing unserviceable sand stone complete all as specified & directed by Engineer-in-charge.

M&L Jodhpur stone roof slabs, self faced, 7.5cm to 10 cm thick, 25 cm to 35 cm wide, hoisted & set, jointed and grouted in cement mortar (1:3) including demolition of existing unserviceable stone roof slab complete all as specified & directed by Engineer-in-charge.

S & F 75 mm bore PVC (SWR) Soil, waste and vent pipes single socketed in any length with rubber ring joints laid in floors or trenches including taking down existing unserviceable pipe of any description complete all as specified & directed by Engineer-in-charge.

S & F 110 mm bore PVC (SWR) Soil, waste and vent pipes single socketed in any length with rubber ring joints laid in floors or trenches including taking down existing unserviceable pipe of any description complete all as specified & directed by Engineer-in-charge.

S&F in repair, PVC connection pipe 15mm dia, 450mm long with PTMT check nuts and washer on both ends complete all as specified & directed by Engineer-in-charge.

M&L Joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated) Fe 410 -W (Gde- E- 250) quality- A with dismantling structural steel work including doors, gates but excluding framed truss etc complete all as specified & directed by Engineer-in-charge.

S&F Pre-painted galvalume aluminium zine coating GI based corrugated steel sheeting 0.50mm thick any colour having tensile strenght 550Mpa in roof coverings fixed with self tapping screws including dismantling of Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings, complete all as specified & directed by Engineer-in-charge. Note :- (i) The fixing of Galvalume roof sheet as in sun-shades & in walls at certain places to be fixed by making of grooves cutting 75mm minimum with making good surface are inlcuded in the cost of item itself. No extra cost shall be paid for the same. (ii) The pattern and design of sunshades to be fixed as per directions of Engr-in-charge.

Demolition of brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified & directed by Engineer-in-charge.

M &L Squared rubble walling Jodhpur type, brought upto courses, well bonded, bedded and solidly hearted, built in CM 1:6 complete all as specified & directed by Engineer-in-charge.

S&F in repairs cast iron nahani trap with CP grating including jointing to waste pipe in cement mortar, diameter of out let 75mm bore fixed in cement concrete type B1 (1:2:4) complete all as specified & directed by Engineer-in-charge.

M&L for 25mm thk PCC 1:2:4 type B0 using 12.5mm graded stone aggregate as in subbase of floors, on roof top as padding & finishing the surface even & smooth without using extra cement including complete removal of existing roof treatment.

M&L for MS props erecting for temporary supports to the structural members like beams, slabs etc. to relieve the load on the members during breaking of damaged concrete, removal guniting, excavation or any dismantling work as per the instruction of engineer in-charge. These supports shall be provided either in the form of props or trestles fabricated using structural steel as per the site requirements complete all as specified & directed by Engineer-in-charge.

M & L for Chipping of slab/ columns/ beams/ chajjas/ parapet/ roof projection/ balcony/ staircase and removing loose mortar with chisel hammer without much impact on concrete surface, clean the surface by sand blasting the surface using river sand with minimum of 6 kg pressure at the nozzle or air blow by electric pressure blower by mechanical compressor, cleaning the exposed reinforcement with wire brushes etc and disposal of debris all lead and lifts, complete all as specified & directed by Engineer-in-charge.

M&L for cleaning & applying rust remover (CICO Clean-o rust) in two coats over rusted reinforcement surface and providing anti corrosive coating with two component epoxy based zinc rich primer/Rust passivation Inhibitor coat at the rate of 6-8 sq. mtr/ltr not less than 50 microns dft with CICO ZINCILATE-500 or equivalent to reinforcement surface as per manufacturer’s instructions including all scaffolding , machinery, tools tackles and clearing of debris. Make: CICO clean-O-rust, CICO ZINCILATE-500 or equivalent in Appx 'C' list of makes.

M&L mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified & directed by Engineer-in-charge. Note : Additional Reinforcement: Check the diameter of the existing rebars and if the diameter is less than 30% of the original diameter, provide additional reinforcement. Cut 12mm dia bars as main reinforcement to the required length with proper development length. Tie them to the prefixed shear connectors so that the additional rebar acts monolithically with the existing ones and core concrete.

M&L for providing leak proof shuttering in any position cut to length and providing including runners supports as per manufacturer’s instructions and including machinery, tools tackles and men materials complete all as specified & directed by Engineer-in-charge. Note :- Scaffolding charges shall deemed to inclusive of quoted rate for respective items of this schedule.

M&L for providing Micro concrete with CICO MICROCRETE at the rate of 25kg per 0.0125 m3 with 20% properly graded 5mm to 10mm silt free aggregate as per manufacturer instructions and mixing concrete with mechanically electrically operated mixer machine etc complete all as specified & directed by Engineer-in-charge. Make: CICO MICROCRETE of CICO Technologies ltd or equivalent in Fosroc/STP/BASF

CEMENTITIOUS ELASTOMERIC SLURRY COAT: M & L for water proofing treatment on roofs of slabs by complete removal/taking down of existing treatement, by applying acrylic based polymer modified cementitious elastomeric flexible composite coating system consisting of applying: First coat applying with CICO TAPECRETE-P151 or equivalent in FOSROC/STP/SIKA/BASF, mixed with neat fresh cement in the ratio of 1:1 by weight after dust free and moist the surface. Laying second layer of Fiber glass cloth of 45 GSM when the first layer is still green. Overlaps of joints of fiber cloth should not be less than 10 cm. Applying final layer of cementitious elastomeric flexible composite coating system. The whole terrace so finished shall be flooded with water for a minimum period of 24 hours for curing and for final test. “All above operations to be done in order by the manufacturer's authorised applicator only.

M & L for providing and applying seamless thermal insulating elastomeric high build liquid membrane for concrete roofs, exterior wall and exposed surface. Make : CICO THERMOSEAL XL or equivalent in / FOSROC/ SIKA/STP Limited as approved with dual effects by reflecting more than 80% of sun rays thereby heating of roof surface reduces remarkably due to high amount of Titanium di oxide & transfer of heat from roof surface is blocked due presence of ceramic micro sphere with the application of roof and exterior side walls, it reduces energy cost approx 20%.

Note : For item Ser No 68 to 75 (i) The structural rehabilitation treatment shall be applied by the company’s authorized applicator only. (ii) Contractor have to get prior approval of applicator or authorized agency by submitting its authorization letter to this office for approval prior to commencement of work. (iii) Submission of 10 year warranty certificate for waterproofing treatment work over roof is mandatory after completion of work.

Excavating in post holes (or similar holes) in soft/ disintegrated rock, each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, watering and removing surplus soil to a distanc n exc 50 m and making good surface complete all as specified & directed by Engineer-in-charge.

M&L for plain cement concrete (1:2:4) type B-2 (using 40 mm graded stone aggregate) as in foundation, filling and mass concrete complete all as specified & directed by Engineer-in-charge.

S&F mild steel in hand rails, half round or other stock section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165, complete all as specified and directed by Engineer-in-charge.

S&F framed work such as grills, gratings, etc with ends of bars shouldered and / or riverted or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, raillings, frame work of water tanks and similar work confirming to Fe-290 grade E-165 complete all as specified & directed by Engineer-in-charge.

S&F rolled mild steel joist, channel, angle or tee sections, fixed independently, without connecting plates, etc (cut to ordinary lengths i.e. within 20mm of the length indicated) conform to Fe 410-W (Gde E-250 quality-A) complete all as specified & directed by Engineer-in-charge.

S&F framed brackets of angles or tees with web and flanges cut to shape, drilled and countersunk for screw, including bending and welding angles, as necessary, gusset plates, riveting, etc.. n exc 10 kg each brackets, conforming to Fe.290.Gde-E-165 (Brackets over 10 kg each to be measured under 'Structural Steel') complete all as specified & directed by Engineer-in-charge.

S&F mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut exc 10cm and n exc 15cm long long dia of neck 5 to 10 mm complete all as specified and directed by Engineer-in-charge.

Taking down carefully surface aluminium or copper point wiring with PVC casing-caping (light, fan, socket, bell or power) including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fittings etc and making good disturbed surfaces complete all as specified & directed by Engineer-in-charge.

M& L Point wiring with 1100 volts grade PVC insulated FR-LSH multistranded copper conductor cable 1.5 sqmm (Phase - Red, Neutral - Black) and earth continuity conductor 1.5 sqmm (Green) drawn into and including concealed rigid non metallic PVC conduit medium grade not less than 20 mm dia ISI marked ivory colour with all conduit fittings / fixing accessories and sunken galvanized pressed steel terminal boxes of thickness not less than 1.2 mm with 3 mm thick phenolic laminated white sheet cover for mounting of Piano Type switches, sockets, fan regulators complete for the following :-

(a) One light point controlled by one switch.

(b) One fan point controlled by one switch.

(c) One socket outlet 6 amp controlled by one switch on the same board with other switches.

All as per item No 85.00 here on before but with copper conductor cable of nominal class area 2.50 sq mm for phase, neutral & earth for One 2/3 pin socket outlet 5 Amps on independent board complete all as specified & directed by Engineer-in-charge.

All as per item No 85.00 here on before but with copper conductor cable of nominal class area 4.0 sq mm for phase, neutral & earth for power socket point 15 Amps complete all as specified & directed by Engineer-in-charge.

S&F switch piano flush button single pole one way 5/6 amp complete all as specified & directed by Engineer-in-charge.

S&F switch piano flush button single pole one way 16 amp complete all as specified & directed by Engineer-in-charge.

S&F socket outlet 2 in 1, 3 pin 6 & 16 amp flush type complete all as specified & directed by Engineer-in-charge.

S&F socket outlet 2 in 1, 2 & 3 pin, 6 amp, flush type complete all as specified & directed by Engineer-in-charge.

S&F hum free electronic step fan regulator 120 - 280 volts of 100 watt capacity (socket type) including connecting up complete all as specified & directed by Engineer-in-charge.

S&F of bell push flush type 5 Amps complete all as specified & directed by Engineer-in-charge.

S&F Ceiling rose, three terminals PVC/polycorbonate, isolated body complete all as specified & directed by Engineer-in-charge.

S&F vertical DBs TPN 4 way 415 V double door powder coated, CRCA steel sheet constructed as per IS : 8623, degree of protection IP 43 - IK 09 with metal door, recess mounted, having insulated 250 amp tinned copper bus bar, neutral busbar, earth bar, din bar, detachable gland plate, interconnection, earthing connection, blanking plates in unused spaces as required,suitable for TP/FP MCCB as incomer including MCCB 100 A , and with SP/TP MCCB's as incoming MCCB FP 100A, 25 KA including taking down existing unserviceable DBs of any description complete all as specified & directed by Engineer-in-charge.

S&F MCB DB SPN 12 way double door IP 43 complete prewired including Bus Bar etc suitable for operation on 240 volt 50 Hz AC supply including necessary provision for inserting the DBs in wall by cutting the brick/stone masonary etc and making good of distrubed surface to match with existing colour of wall including taking down existing unserviceable MCB DBs of any description complete all as specified & directed by Engineer-in-charge.

S&F MCB's single pole and neutral 63 Amps, 240 Volts,10 KA rapturing capacity 'C' curve including taking down existing unserviceable MCB SPN of any description complete all as specified & directed by Engineer-in-charge.

S&F MCB's single pole 10 Amps to 32 Amps, 240 Volts,10 KA rapturing capacity 'C' curve including taking down existing unserviceable MCB SP of any description complete all as specified & directed by Engineer-in-charge.

M&L for submain wiring with approved colour code/as per IS (Red,black & green for single phase) concealed conduit circuit with two single core PVC insulated cable with multistranded copper conductor of nominal cross sectional area of 6.00 Sqmm (FRLS) in conduit including one run of PVC insulated multistranded copper conductor nominal cross sectinal area of 6.00 Sqmm (FRLS) of continous earth wire green in colour including taking down existing unserviceable submain wiring of any description complete all as specified & directed by Engineer-in-charge. Note :- Two runs of 6.00 Sqmm cable & one run of 6.00 Sqmm cable as earth wire and one run of PVC conduit shall be measured and paid as one unit length.

S&F building security light fitting LED 35 Watt IP 66 IK 07 pressure dia cast aluminium housing with high efficient LED as lihjting souce and PC cover having TOP opening sepreate drive compartment etc and connecting including taking down existing unserviceable light fitting of any description complete all as specified & directed by Engineer-in-charge.

S&F bracket of GI pipe light grade of 40mm dia, 1.2 meter in length clamps made of FI 40 mm x 6mm incl nuts, bolts & washers, painting and including taking down existing bracket complete all as specified & directed by Engineer-in-charge.

S & in repair of LED box type Integrated Batten 40 watt having Aluminum Extruded housing in white powder coated Finish with high translucent PC Cover, Elegant Design, IP 20 Protection. Dimensions of the Fitting Shall be Not less then 1200 MM ( Length) X40 MM ( Width ) X 63 MM ( Height ). Lumens output of the fitting shall be not less then 4400 lm, CCT 5700 – 6500K, buring hours 50,000 Surge Protector 4 KV, PF>= 0.95 , Separate detachable type Electronic constant current drivers for easy replacement and maintenance, THD < 10%, Necessary mounting arrangements. The fixture shall be suitable for wall mounting /suspension mounting as per site requirement . The Manufacturer of the fixture shall have in house NABL Accredited Lab and must produce certificate of the same along with LM-79 / LM80 / Test Report as per Crompton CAT PART NO Shelter . CIS -305-40-57-SL-DP-NWH or equivalent in Appx 'C' list of make.

S&F LED tube light fitting 10 watt tube LED Neutral white in colour, 600 mm in length wall mounted LED batten,extruded aluminium heat shink provided for efficient heat dissipation & integrated electronic driver,optic diffused type ENDURA LINER NEO including all electric connection with whilte flexible cord 1.50 Sqmm 3 core as required including taking down existing unserviceable LED tube light fitting of any description complete all as specified & directed by Engineer-in-charge.

Taking down ceiling fan/ exhaust fan of any sweep, dismanting blade and including preparation, filling cavity applying one coat of synthetic enamel paint by spraying with machine, re-assembling the fan body to fan and re-fixing in its original position or any other position including provide cable from ceiling rose or connector to fan of suitable size complete all as specified & directed by Engineer-in-charge. Note :- Rate quoted by the contractor shall deemed to inclusive of replacing of quarter pin, nut bolt with check nut, rubber real etc.

M&L bore earthing not less than 250 mm dia 16 feet deep filled with black soil up to 7 feet from bottom complete with galvanized iron pipe 40 mm bore medium grade 3 meter long tapers at bottom & provided 12 mm holes (staggered) at 75 mm centre to centre up to 2.5 meter of length from bottom , burried directly in ground filled with 45 cm alternate layer of chemical magnisium sulphate, charcoal & salt up to ground level connected to galvanized iron wire 4 mm dia as earthing lead up to Panel /DB BOX as per site requirement by means of bolt and nut, check nuts and washer of galvanized iron or steel including brazing work and 40mm dia light grade pipe for earth lead protection including test point terminal cover the earhing hole by PCC chamber and GI cover and testing on completion and including taking down existing earthing complete all as specified & directed by Engineer-in-charge.

NOTE FOR ITEM No. 123.00 [i]. Excavation & earth work in any type of soil including removing of surplus material upto 100M [ii]. PCC (1:3:6) type C1 using 20mm graded stone aggregate in pit & 40mm thick precast RCC (1:2:4) type B1 cover 50x50 cm with 8mm round bar @ 15 cm C/C both ways. [iii]. Main earthing wire from earth electrode to test point upto 7.5 mtr. [iv]. Funnel with watering pipe [GI pipe] 20mm bore [ISI marked] medium grade & copper lugs and charcoal & salt as reqd. [v]. GI protection pipe of size 40 mm bore light grade 7.5m.

Supply, laying, testing and commissioning of cable XLPE insulated screened PVC bedded, galvanized steel strip or wire armoured electric power cable (heavy duty) 1100 volt grade with stranded aluminium conductor of size of cross sectional aera 16 Sqmm 4 core with cable lugs, gland, cable termination box etc and including taking down old Unsv existing cable complete all as specified & directed by Engineer-in-Charge. Note : - Earthwork excavation sand cushioning, Jodhpur Stone patti, GI protection pipe shall be measured and paid separately in their respective items

M&L for sand cushioning to under ground cable using tibba sand and gently punning to cushioning to cable complete all as directed by Engineer-in-Charge. (Note :- Punned thickness of sand cushioning shall only measured for the purpose of payment).

Supply & laying 40 to 50mm thick roughly hammer dressed Jodhpur stone patti cable cover 25cm to 30cm wide and n. exc 60cm long each laid dry abutting with each other with maximum gap between adjacent slabs n. exc 10mm complete all as specified & directed by Engineer-in-charge.

Supply and fixing MCCB 4 Pole 63 Amps, breaking capacity 16 KA, thermal & magnetic adjustable type, 415 volts with extended copper terminals IP-43 complete and connecting links on LT panel/feeder pillar including dismantling/taking down existing unserviceable MCCB complete all as specified & directed by Engineer-in-charge. (Note: ICS = ICU 100%).

S&F steel water tubing 50 mm bore, 'light grade' galvanised, with pole for protection of cable etc and including taking down existing pipe of any description complete all as specified & directed by Engineer-in-charge.

Material and labour for cutting the existing bituminous road / hard standing to size not exceeding 45cm wide and depth not less than 45cm for passing of UG cable through GI pipe and making good the disturbed surface filled with excavated material and top 200mm depth with plain cement concrete 1:3:6, type C1 using 20mm graded aggregate complete all as specified & directed by Engineer-in-charge.

AMBEY MAA CONSTRUCTION COMPANY (BID ID -3082753)

deepaktraders (BID ID -3082492)

GEMRARAMCONTRACTOR (BID ID -3081716)