Widening and hotmixing of Rural road to Govt. Agricultural farm at Cuinamol to Kalay railway station ID.No. 67604 in a length of 1.390 kms in V.P. Kalay of Sanvordem Constituency in Sanguem Taluka.

Earthwork in excavation for roadway in all types of strata comprising any of the materials such as soil, silt, clay gravel murrum of all varieties shingles pebbles all types of conglomerates, laterite rock, ordinary soft rock, disintegrated rock fissured rock shuttered decomposed rock or weathered rock and all such other materials as described under Appendix "A" to those specification either in full or parts as the case may be by mechanical means or any other approved means including cutting and pushing the earth to site of embankment, including trimming bottom and side slopes in accordance with requirements of lines, grades and cross sections. as per MoRT & H Specification 301 or adopting any approved method or method as the case may be convenient or permitted inclusive of chiselling, wedging blasting prohibited etc. in all conditions such as dry moist saturated submerged foul conditions including shoring strutting etc. and as directed by the Engineer in - charge including dressing of sides ramming of bottoms including getting out the excavated soft/rock to be levelled & neatly dressed including pumping and bailing of water, carriage and disposal of excavated material barricading danger lighting guarding and disposal of excavated earth as directed by the Engineer - in Charge including all leads and lifts etc. complete.

Rubble packing with hard laterite stone under floors including watering ramming and consolidating etc. in pipeline trenches and other foundations complete.

Providing & laying cement concrete 1:2:4 (1 cement: 2 coarse sand: 4 graded granitic or basaltic stone aggrt. 20 mm. nominal size) excluding cost of centering, shuttering and finishing in: a) All works upto plinth level

Centering and shuttering including struttings, propping etc. and removal of formwork for : a) Foundations, footings, bases for columns and mass concrete.

Supplying of laterite stone soling of size 150-200 mm size and murrum having P.I. Value not more than 6 and laying including packing with smaller stones and consolidation with power road roller including spreading, watering and consolidation of binding material etc.(Measurements shall be considered on finished item) .

Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with 3-wheeled steel/vibratory roller 8-10 tonnes in stages to proper grade and camber, applying and brooming requisite type of screening/binding materials to fill-up the interstices of coarse aggregate, watering and compacting to the required density.as per MORTH Specification 404. By Manual Means, Grade - II.

Providing and laying 50mm(consolidated thickness)full grout using granitic or basaltic stone of specified grading at 6.00 cu.m. per 100 sq.m. grouting with hot bitumen straight run bitumen(or with such bituminous material of grade and type as specified by the Engineer-in-Charge)at 5.0kg. per sq. m. binding with key aggregate of granitic or basaltic stone of specified grading at 1.5 cu.m. per 100 sq.m. including Providing and laying seal coat sealing the voids in a bituminious surface laid with F.E loader with 1 Cu.m. bucket capacity to the specified levels, grade and cross fall using Type A seal coat with 0.98 kg/sqm of bitumen of grade as per MoRT&H specifications clause 513.

Providing and applying tack coat with bitumen grade of 80/100 or bitumen emulsion using pressure distributor on the prepared bituminous/granular surface cleaned with mechanical broom as per MoRT&H specifications clause 503 a) Bitumen 80/100 @ 0.20 kg/sq.m

Providing and laying bituminious concrete with 40-60 TPH Drum Mix type Hhot mix plant producing an average output of 50 tonnes per hour using crushed aggregates of specified grading, premixed with bituminious binder to mix with filler, transporting the hotmix to work site, with all leads laying with a hydrostatic/hydraulic paver finisher with sensor control to the required grade, level and alignment, using antistripping agent rolling with smooth wheeled, vibratory or tandem rollers to achieve the desired compaction complete as per MoRT&H Specifications Clause 509. Grade-II (13mm nominal size) @ 6.0% Bitumen of grade 60/70 a) Antistripping agent @ 0.5% of bitumen content

Providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC : 35. The finished surface to be level uniform and free from streaks and holes as per MORTH Specification 803.