CONSTRUCTION OF PANCHAYAT GHAR AT SOFIGUND BLOCK ANANTNAG

PART A ( MAIN BUILDING)

Engagement of manual labour for Clearence of site including disposal of same, all complete job

Earth work in excavation by mechanical means (hydraulic excavator) in foundation trenches or drains (not exceeding 1.5M in width as well as 10Sqm on plan) including dressing of sides ramming of bottoms lift up to 1.5M including getting out the excavated soil and disposal of surplus excavated soil within a lead of 1 M from edge of cutting.

Supplying and laying of stone soling hand packed tightly including ramming, watering.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering. All work up to plinth level.1:4:8 (1Cement: 4 fine sand: 8 graded stone aggregate 40mm nominal Size)

Providing and laying in position specified Grade of Reinforced cement concrete excluding the cost of centring, shutering and finishing of all work.1:1.5:3(1 Cement : 1.5 Coarse sand : 3 Graded stone aggregates 20 mm nominal size) Raft

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering. All work up to plinth level.1:3:6 (1Cement: 3 fine sand: 6 graded stone aggregate 20mm nominal Size)

Centering and shuttering including strutting propping etc. and removal of form work; foundations footings bases of columns

Centering and shuttering including strutting propping etc. and removal of form work; suspended floors /beams

Providing and Laying Damp Proof course 50 mm thick with cement mortar in 1:2:4 mix, 20mm nominal size of aggregate and curing complete.

Brick work with FPS bricks of class designation 75 in super structure in cement mortar 1:6 (1 Cement : 6 Coarse sand) including Extra Brick Work.

Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embeddings in cement concrete block 30x10x15 cm 1:3:6 mix ( 1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size).

Providing wood work in frames of Doors,windows, clerestory window and other frames,wrought frames and fixed in position.

Providing and fixing 30 mm thick glazed shutter for windows and clearstory windows using 10kg/sqm (4mm thick)glass panes including black enamelled ISI marked M.S hinges with necessary screws. Imported wood (KD)

Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood(KD) and well matched teak face veneers on both faces of shutters. With ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws 30 mm thick

Providing and fixing 30 mm thick wire gauze shutters using galvanized M.S. wire gauze of average width for aperture 1.4 mm in both directions with wire of dia. 0.63 mm for doors, windows and clerestory windows with ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws as per direction of Engineer-in-charge, imported (KD) wood

Providing and fixing ISI marked aluminum fittings ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade etc. complete :

150 mm tower Bolts (D)

100mm tower Bolt(W/V)

Link/Godrej Al Drop Lock type

125 mm Handle

100mm Handle

bright finished brass hard drawn hooks and eyes 150 mm

Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15°, landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto five level including curing but excluding the cost of centring, shuttering, finishing and reinforcement with 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size)

Reinforcement of RCC works including straightening, cutting, bending placing in position and binding all complete. TMT bars

Filling by Available excavated earth (excluding rock) in trunches,plinth,sides of fondation etc, in layers not exceding 20 Cm in depth ,consolidation each deposited layer by ramming and watering lead upto 50m and lift upto 1.5 m.

Supplying and filling in plinth with fine sand /Nallah Muck under floors including watering rammiing ,consolidating and dressing , carriage complete job

Cement concrete flooring 1:2:4 (1Cement: 2 coarse sand: 4 graded stone aggregate). 50 mm thick 12.50mm nominal size stone aggregate (crushed) including glass strips at a squared interval of 5'x5'

12 mm thick plaster in Cement Mortar 1:6 mix.

6 mm thick plaster in Cement Mortar 1:3 mix.

Structural steel work welded in built up sections, trusses and frame work including cutting, hoisting fixing in position and applying a priming coat of approved steel primer all complete in angles / flats / tubes / channels etc. I/C RAILLING

P/F of threaded truss bolts of 16 mm dia and 45 cm long with angle iron strip at bottom welded i/c its embedment in concrete as per the directions of site engineer, complete job

Providing C.G.S. sheet roofing including vertical / curved surface fixed with polymer coated J or L hooks, bolts and nuts 8mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces),excluding the cost of purlins, rafters and trusses and including cutting to size and shape. 0.50mm thick

Providing ridges or hips of width 60cm overall width plain G.S. sheets fixed with polymer coated J. or L hooks, bolts and nuts 8mm dia G.I. limpet and bitumen washers complete. 0.50 mm thick with zinc coating not less than 275 gram/m2

Providing and fixing in position collapsible steel shutters with verticalchannels 20x10x2 mm and braced with flat iron diagonals 20x5 mm size,with top and bottom rail of T-iron 40x40x6 mm, with 40 mm dia steelpulleys, complete with bolts, nuts, locking arrangement, stoppers,handles, including applying a priming coat of approved steel primer.

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622 of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1cement :4 coarse sand) including grouting the joints with white cement and matching pigments etc. complete Size of tile 500x500 mm

Making plinth protection 50 mm thick of cement concrete 1:3:6 (1 cement:3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over75mm thick bed of dry brick ballast 40mm nominal size, well rammed.

Finishing walls with water proofing cement paint of required shade on New work (two or more coats applied @ 3.84 kg/10sqm)

Applying priming coat with ready mixed pink or grey primer of approved brand and manufacture on wood work

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade. Two or more coats on new work

Providing and applying white cement based putty of specified thickness, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. 2 mm thick

Providing and fixing gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels Granite of any colour or shade

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade on New work (two or more coats) over and including priming coat with water thinnable cement primer

Providing/Fixing of Foundation/Inauguration stone for Pachanyat Ghar including providing Pre-execution , during execution & post execution photographs complete job

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per I.S. 13983 with C.I. brackets and stainless steel plug 40 mm, including necessary fittings and brackets, cutting and making good the walls wherever required with PVC flexible waste pipe of 40mm dia for sink or wash basin incl coupling etc. Complete job, Kitchen sink with drain board 510x1040mm bowl depth 178mm

Providing & Fixing of C.P. Brass single lever basin mixer complete including & making good the walls / Floors wherever required (jaquar or equivalent)

P/F PVC pipe heavy duty (standard quality ), Water or Vent pipes and necessary bends,junction,inclusive of rubber washers,adhesives,complete job 75 mm dia

Providing and fixing PPR pipes complete with fittings and clamps including cutting chases and making good the walls etc, 16 mm dia

Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes i/c ball cock

Providing and fixing ball valve (brass of approved quality complete: 20mm nominal bore

Carriage of different material from nearest source to site of work Stone /sand agg 40mm / 20 mm & sand Avg lead of 18 Km.

Bricks, Qty vide item 9 = 46.15 @25% Plaster qty vide item item 21 = [email protected]

Bricks from Av lead of 20 Km

Supplying and fixing of 25mm size of medium class PVC conduit along with accessories in surface /recess including cutting the wall and making good the same in case of recessed conduit as required

Supplying and fixing concealed metal box of following size (nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including painting etc as required . 75mm x 75 mm x 60 mm deep

providing and fixing MS Fan clamp type I or II of 16 mm dia MS bar (anchor) bent to shape with hooked ends in RCC slabs or beams during laying, including painting the exposed portion of loop,all as per standard design ,complete job

PART B ( CSC FOR MAIN BUILDING )

Earthwork in excavation by mechenical means in trenches for foundation (Not exceeding 1.5m in width), depth upto 1.5m incl. disposal of excavated earth upto 1m from cutting edge. (All Kinds of Soil)

Providing & laying of dry soling hand packed, in foundation & Trecnhes incl all carraiges complete job.

P/L in position cement conc. of grade 1:4:8 (1 cement : 4 fine sand : 8 Nallah graded stone agg 40 mm N/s) excl. cost of centering & shuttering in all work upto plinth level

P/L in position cement conc. of grade 1:3:6 (1 cement : 3 fine sand : 6 stone agg 20 mm N/s) excl. cost of centering & shuttering in all work upto plinth level.

Brick work with common burnt clay F.P.S. (non-modular) bricks of class designation 75 in foundation & plinth in cement mortar 1:6 (1 Cement : 6 coarse sand)

Extra for B/W above Plinth Level upto Floor V Level

Centering and Shuttering I/c Strutting, Propping etc & removal of formwork for roof. Slab

plinth

Edges of slabs and breaks in floors and walls under 20 cm wide

Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15°, landings,balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto five level including curing but excluding the cost of centring, shuttering, finishing and reinforcement with 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size)

Reinforcment for R.C.C. work incl. straightening, cutting, bending, placing in position & binding all complete.

Dry random rubble masonry with hard stone in foundation & plinth using Quarry stones incl all carriages complete job

P/F of structural steel door/window frames and shutters complete job i/c priming and painting complete job i/c tower bolts/Aldrops/handle complete job.

P/F of coloured CGI sheets for doors complete job (0.5 mm thk)

12 mm Cement plaster on the rough side of single or half brick wall of mix: 1:6 mix

P/L 40mm thick flooring with 20 mm nominal size stone aggregate.

P/Fixing of Tiles of standard quality

Carriage of Various materials from source to W.S by MT and H.L.

a) Sand for an avg. lead of 15 Kms by MT

b) Bajri for an avg. lead of 20 Kms by MT and

e) Bricks for an avg. lead of 20 Kms by MT

P & fixing W C Squatting Pan ( indian type) W c Pan with 100 mm dia PVC " P" trap +10 litre low level PVC flushing cistern including flush pipe, manully controlled device with all fittings & fixture Complete Long pattern W.C Pan of size 580x440 mm

Providing and fixing rectangular high density polyethylene water storage loft tank with cover, con colour of opaque white or as approved by Engineer-in-charge. The rate includes making necessary holes for inlet, outlet & over flow pipes. The base support i/c fittings (Water storage tank)

Finishing walls with water proofing cement paint of required shade on New work (two or more coats applied @ 3.84 kg/10sqm)

Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipes conforming to IS: 15801, UV stabilized and anti-microbial fusion welded, having thermal stability for hot and cold water supply including all PP-R plain and brass threaded Polypropylene random fitting, complete job Internal work Concealed fixing the pipe with clamps at 1.00 meter spacing including cutting chases and making good the wall etc. ii)PN-16 pipe , 20mm OD(SDR-7.4)

P/F Door Tee 100mm dia pvc of approved make type B

P/F soil waste and vent pipes IS 13592& fittings (IS14735) suitable to rubber ring joints which includes bends, rubber rings,jointing, junctions, etc all fittings complete job 11 0mm dia PVC SWR pipes complete job (Type B)

P/F soil waste and vent pipes IS 13592& fittings (IS14735) suitable to rubber ring joints which includes bends, rubber rings,jointing, junctions, etc all fittings complete job 75 mm dia PVC SWR pipes complete job (Type B)

P/F PVC cowel over vent pipe of approved quality type B

P/F 100x75 mm reducer PVC of approved quality

P/F of floor traps 110 mm with double chrome plated cover one grated and one closed and all other fittings required of standard quality, complete job.

Providing and fixing wash basin with C.I. brackets, 15mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, incl pvc connection & 50 mm waste pipe incl cutting and making good the walls wherever required White Vitreous China Wash basin size 630x450 mm with a single 15 mm C.P. brass pillar taps.

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265mm sizes respectively incl all accessories complete job.

P/F brass bib cock of approved quality 15 mm dia of standard brand

P/F brass angle value of approved quality

P/F gun metal gate valve of approved quality 20mm nominal board

Providing and fixing PTMT soap dish holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106gms

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing Rectangular shape 453x357 mm

Constructing brick masonry chamber/manhole with common burnt clay (non modular) bricks of class designation 7.5 in cement mortar 1:4 ( 1 cement : 4 coarse sand) C.I. cover with frame & hinges (light duty) 455x610 mm internal dimensions i/c padlock arrangement with lock, fixed in 1:1.5:3 mix,, inside plastering 12 mm thick with cement mortar 1:3 ( 1 cement : 3 coarse sand) finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design :

Add provision for Signboard/Photograph/SBM logo/unforeseen item (STA) AND MISCELLANEOUS NITEMS