Construction work sub-Regional Science Centre and Planetarium at North Lakhimpur, Assam (Additional Works)

Amount

Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth All kinds of soil

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.

Dry brick pitching half brick thick in drains including supply of bricks and preparing the surface complete : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 40 mm nominal size derived from natural sources)

1:2:4 (1 cement : 2 coarse sand(zone-III) : 4 graded stone aggregate 20 mm nominal size)

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Hot rolled deformed bar

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. Hot rolled deformed bars

Centering and shuttering including strutting, propping etc. and removal of form for Foundations, footings, bases of columns, etc. for mass concrete

Columns, Pillars, Piers, Abutments, Posts and Struts

Lintels, beams, plinth beams, girders, bressumers and cantilevers

Suspended floors, roofs, landings, balconies and access platform

Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size de rived from natural sources)

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge. All works above plinth level upto floor V level .

Providing M-30 grade concrete instead of M-25 grade BMC/ RMC. (Note:- Cement content considered in M-30 is @ 340 kg/cum)

Providing and fixing sheet covering over expansion joints with iron screws as per design Non-asbestos fibre cement board 6 mm thick as per IS: 14862. 200mm wide

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:4 (1 cement : 4 coarse sand)

Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand(Zone III) : 4 graded stone aggregate 12.5mm nominal size).

Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:4 (1 cement : 4 coarse sand)

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash Kiln seasoned and chemically treated hollock wood

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished welded type tubes.

Providing corrugated G.S. sheet roofing including vertical/curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 0.63 mm thick with zinc coating not less than 275 gm/ m²

Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete : Barge board (Upto 300 mm).

Providing & fixing at all heights, levels and locations Mill finish Aluminium alloy roofing sheets of alloy IS designation 31500, temper Hx8 conforming to IS 737 and dimensions as per IS code 2676 with characteristics of good formability and corrosion resistance. The profile sheets shall be fixed to truss members in slope or required pitch or curvature with Hex cap headed self drilling/tapping Stainless steel screws M6, 50 mm long with 3 mm EPDM seal washer etc. all inclusive of labour, scaffolding, T&P and sundries etc. complete as per directions of the Engineer-In-Charge. (Cost of truss/frame work shall be paid separately). 0.71 mm, troughed profile with center to center pitch of 200 mm, depth of 32 mm, overall profile width1092 mm, cover width 1000mm.

15 mm cement plaster on the rough side of single or half brick wall of mix : 1:4 (1 cement: 4 fine sand)

Providing and laying Ceramic glazed floor tiles of size 300x300 mm(thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement :4 Coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including pointing the joints with white cement and matching pigment etc.,., complete.

Providing and fixing 1st quality ceramic glazed floor tiles conforming to IS : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kgper sqm including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent

Providing and laying 500x500x40mm thick Turf paver (Turf pave XD) on 150mm thick sub grade of compacted bed of 20mm thick nominal size stone aggregate and base course and filling with 150mm thick jamuna sand including spreading, well ramming, consolidating and finishing smooth etc. all complete as per direction of Engineer-in-charge.

Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows, fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Second class teak wood 35 mm thick shutters

Cement plaster skirting up to 30 cm height, with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement. 18 mm thick

62 mm thick cement concrete flooring with concrete hardener topping, under layer 50 mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) and top layer 12mm thick cement hardener consisting of mix 1:2 (1 cement hardener mix : 2 graded stone aggregate, 6mm nominal size) by volume, hardening

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Finishing walls with Acrylic Smooth exterior paint of required shade : 13.46.1 New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : New work (two or more coats) over and including water thinnable priming coat with cement primer

Applying priming coat: With ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and soft wood)

Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications : Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @0.75 ltr/10 sqm of approved brand and manufacture

Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @ 0.80 ltr/ 10 sqm of approved brand or manufacture

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work.

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. Fixed to openings /wooden frames with rawl plugs screws etc.

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. In cement mortar

Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge.

Dismantling aluminium/ Gypsum partitions, doors, windows, fixed glazing and false ceiling including disposal of unserviceable material and stacking of serviceable material with in 50 meters lead as directed by Engineer-in-charge.

Providing and fixing mineral fibre false ceiling tiles at all heights of size 595X595mm of approved texture, design and pattern. The tiles should have Humidity Resistance (RH) of 99%, Light Reflectance > 85%, Thermal Conductivity k = 0.052 - 0.057 w/m K, Fire Performance as per (BS 476 pt - 6 &7)in true horizontal level suspended on interlocking T-Grid of hot dipped all round galvanized iron section of 0.33 mm thick (galvanized @120 gsm) comprising of main T runners of 15x32 mm of length 3000 mm, cross T of size 15x32mm of length 1200 mm and secondary intermediate cross T of size 15x32 mm of length 600 mm to form grid module of size 600x600 mm suspended from ceiling using galvanized mild steel item (galvanised @ 80 gsm) 50 mm long 8mm outer diameter M-6 dash fasteners, 6 mm diameter fully threaded hanger rod up to 1000 mm length and L-shape level adjuster of size 85x25x2 mm, With 20 mm thick beveled tegular mineral fibre false ceiling tile (NRC 0.7)

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately). Polyester powder coated aluminium (minimum thickness of polyester powder coating 50 micron)

Providing and fixing 12mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS:12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge. Pre-laminated particle board with decorative lamination on both sides.

Providing and fixing anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P brass/ stainless steel screws @ 200mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer-in-charge. (Only weight of grill to be measured for payment).

Supplying Aluminium Ladder

Providing and fixing 2nd class teak wood plain lining tongued and grooved, including wooden plugs complete with necessary screws and priming coat on unexposed surface. 40 mm thick

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works.

Providing and fixing mild steel round holding down bolts with nuts and washer plates complete.

Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3 mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer. Using M.S. angels 40x40x6 mm for diagonal braces

Banking excavated earth in layers not exceeding 20 cm in depth, breaking clods, watering, rolling each layer with ½ tonne roller, or wooden or steel rammers, and rolling every 3rd and top-most layer with power roller of minimum 8 tonnes and dressing up, in embankments for roads, flood banks, marginal banks, and guide banks etc., lead up to 50 m and lift up to 1.5 m : All kinds of soil

Construction of granular sub-base by providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Engineer-in-Charge. 16.78.2 With material conforming to Grade-II (size range 53 mm to 0.075 mm) having CBR Value-25

Supplying and stacking at site. 53 mm to 22.4 mm size stone aggregate.

Laying, spreading and compacting stone aggregate of specified sizes to WBM specifications in uniform thickness, hand picking, rolling with 3 wheeled road / vibratory roller 8-10 tonne capacity in stages to proper grade and camber, applying and brooming requisite type of screening / binding material to fill up interstices of coarse aggregate, watering and compacting to the required density .

Providing and laying factory made chamfered edge Cement Concrete paver blocks In foot path, park & lawns driveway or light & traffic parking etc. of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of course sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand, all complete as per manufacturer's specifications & direction of Engineer in-Charge. 80mm thick Cement concrete paver block of M-30 grade with approved colour, design & pattern.

Providing and fixing concertina coil fencing with punched tape concertina coil 600 mm dia 10 metre openable length ( total length 90 m) having 50 no rounds per 6 metre length, upto 3m height of wall with existing angle iron 'Y' shaped placed 2.4m or 3.00m apart and with 9 horizontal R.B.T. reinforced barbed wire, stud tied with G.I. staples and G.I. clips to retain horizontal including necessary bolts or G.I. barbed wire tied to angle iron, all complete as per direction of Engineer-in-charge, with reinforced barbed tape(R.B.T.) /Spring core (2.5mm thick) wire of high tensile strength of 165 kg/ sq.mm with tape (0.52 mm thick) and weight 43.478gm/ metre (cost of M.S. angle, C.C. blocks shall be paid separately)

Fencing with R.C.C. post placed at required distance, embedded in cement concrete blocks, every 15th post, last but one end post and corner post shall be strutted on both sides and end post one side only, provided with horizontal lines and two diagonals of barbed wire weighing 9.38 kg per 100metres (minimum), between the two posts fitted and fixed with G.I. staples on wooden plugs or G.I. binding wire tied to 6 mm bar nibs fixed while casting the post (cost of R.C.C. posts, struts, earth work and concrete to be paid for separately) :- Payment to be made per metre cost of total length of barbed wire used. With G.I. barbed wire

Providing and fixing Stainless Steel pipe and fitting of grade AISI 304 as per JIS standard 3448 complete with press type fitting (fitting shall be paid for separately) i/c fixing of the pipe with clamps at 1.00 m spacing including cutting and making good the walls including testing of joints complete as per direction of Engineer-in-charge. (The pipe length inserted in the fitting shall not be measured for payment) Internal work - Exposed on wall 48.60 mm outer dia Pipe

Providing,fixing,testing & Commissioning of Single headed Gun Metal ISI Marker Oblique pattern Hydrant Landing valve with 80 mm dia, flanged inlet & 63 mm dia instantaneous type female outlet complete with cap and chain twist release lug and all accessories as per IS : 5290-1983 (Type -'A') and specifications complete as required. (MAKE - ESSEL/NEWAGE/SWATI ISI Mark)

Providing RRl Hose with ISI Marked (IS:636) 63 mm diaX15M long complete with instantaneous type Gun Metal 63 mm dia ISI Marked male & female couplings (IS: 903) bound & riveted to hose pipes with copper rivets and copper wire complete as required. (MAKE: NIRMAL RUBBER/ NEWAGE)

Providing & Fixing of weather proof hose cabinets fabricated from 16 S.W.G M.S Sheet with centre opening full front glass door and locking arrangement suitable to accommodate one landing valve (Yard Hydrant), 2nos 15M Long hoses and 1 no. Branch Pipe with nozzle. The cabinet shall be painted with one coat of primer and 2 or more coats of synthetic enamel paint of approved make & shade and shall be suitably mounted on a raised masonry platform complete as reqd. (Make - Self Fabricated) 750X600X300

Supplying,Installation,Testing & Commissioning of Fire Aid Hose Reel Drum with 30mtrs ong rubber hose and GM shut off nozzle 25 mm dia Gate Valve, Union pipe complete set confirming to IS: 884

Providing & Fixing of Gun Metal 63 mm dia Short Branch Pipe 20 mm dia nozzle, ISI marked (IS: 903) complete as required. MAKE - ESSEL/WINCO/NEWAGE)

Providing & Fixing of Gun Metal Fire Brigade connection (withdrawl connecting head) consisting of 63mm instantaneous type male coupling with built in check valves and 150mm dia flanged outlet complete with bolts, nuts and rubber insertions as per IS:904-1983 complete as reqd. MAKE - ESSEL/SWATI/NEWAGE a) 04 way

Providing & Fixing of weather Proof M.S Cabinet (to enclose above Inlet Collection Head Connection) fabricated from 16 S.W.G M.S sheet centre opening with 3mm thick full front glass door and locking arrangement duly painted with one coat of primer and two or more coats of synthetic enamel paint of approved make and shade and suitably mounted. Exact size and shape shall be subject to site conditions and prior approval. (Make - Self Fabricated)

Providing & Fixing of Gun Metal fire Brigade suction hose coupling (draw out connection) with nut for female coupling as per IS:902-1974 complete with 150 mm dia GI suction pipe and foot valve (to be connected to static Tank) complete as reqd. (Make : Self Fabricated).

Providing & fixing of Weather Proof M.S cabinet (to enclose above draw out connection) fabricated from 16SWG M.S sheet centre opening with 3mm thick full front glass door and locking arrangement duly painted with one coat of primer and two or more coats of synthetic enamel paint of approved make and shade and suitable mounted. exact size and shape shall be subject to site conditions and prior approval) (Make : Self Fabricated)

Providing, Fixing, Testing & Commissioning of Air Release Valve 25 mm dia

Providing, Fixing, Testing & Commissioning of Mild Steel Black Pipe (IS:1239 Part-I) Heavy class including cutting, screwing, welding etc, flanges, bends, tees, reducers, elbow, clamps hangers etc including cutting holes and chases in brick or RCC walls/slabs and making good the same to the approval of Engineer - in - charge/ consultant complete including painting with one coat of primer and two or more coats of synthetic enamel paint of approved make and shade including steel work complete as required.MAKE - TATA / JINDAL / NEZONE 200 mm dia

150 mm dia

100 mm dia

80 mm dia

25 mm dia

Providing, Fixing, Testing & Commissioning of Mils Steel Black Pipe (IS: 1239 Part - I) Heavy class including cutting, screwing, welding etc complete with all fittings (but welded) viz flanges, bends, tees, elbows,reducers etc including excavation (upto 1.5 m Deep) back filling and removal of surplus soil & providing anti corrosive treatment (coating and wrapping) as per IS: 10221 with 4mm thick tape complete as reqd.MAKE - TATA / JINDAL / NEZONE 150 mm dia

100 mm dia

80 mm dia

Supplying & Fixing Cast iron body Non Return valves complete with matching flanges,rubber insertion, nuts, bolts and washer etc. (IS:5312) of following sizes complete as reqd. (Make: Koley/Kalpana/Sant) 150 mm dia

100 mm dia

80 mm dia

25 mm dia

Supplying & Fixing Cast iron body Butterfly Valves with matching flanges rubber insertion, nuts, bolts and washer etc. (IS: 13095) of following size complete as reqd. (Make - Koley/Kalpana/Sant/ Zoloto) 150 mm dia

80 mm dia

Providing, Fixing, Testing & Commissioning of G.M Stop Valve ISI Marked screwed type tested to 30Kg/cm2 pressure as per IS:778-1984 of following sizes complete as reqd. 25 mm dia

15 mm dia

Constructing brick mesonary chamber 1200X1200X1200 cms inside with 75 class designation brick work in cement morter 1:5 (1 Cement : 5 Sand) for sluice valves with CI frame and cover 600X600 cms and RCC Top 5 lab 1:2:4 mix (1cement : 5sand : 10 graded stone aggregate 40 mm normal size) and inside plastering with cement morter 1:3 (1cement : 3sand) finished with a floating coat of cement as per standard design.

Providing, erection, testing, commissioning of cast iron Foot valve/Stainer confirming to IS:4038/1538 complete with flanges, nuts bolts and washer etc as required.(Make - Koley/Kalpana/Audco) 150 mm dia

80 mm dia

Providing, erection testing & commissioning of pressure gauge 100 mm dia (0-10kg/cm2)

Providing, erection, testing & Commissioning of Pressure switch.

Supply & laying of following size NP2 class R.C.C Hume pipe i/c collars jointed with stiff mixture of cement merter 1:2 (1 cement : 2 tine sand) across the road if required digging the trenches, refilling the same laying of pipe ramming the soil etc as required. 300 mm dia

Supply &fixing of PVC Tank 500 ltr capacity with acessories

FIRE EXTINGUISHER Supply, Fixing of ABC Stored Pressure Fire Extinguisher with built - In pressure Gauge to know the Readyness of the Extinguisher Squeeze Grip Handle As per IS: 13849 with ISI Mark (06 kg capacity) Brand - Firestop / Firend / Fire shield)

Supply, Fixing of Carbon dioxide fire Extinguisher confirming to IS : 2878 with ISI Mark (4.5) Ltrs. Brand - Firestop/ Firend/ Fireshield)

Supply, Fixing ofMechanical Foam stored Pressure Fire Extinguisher with built – In Pressure Gauge to know the Ready ness of the Extinguisher Squeeze Grip Handle as per IS:13849 with ISI mark. (9 Ltr capacity) BRAND : FIRESTOP / FIREND / FIRE SHIELD

Supply, Fixing of 9 Ltr capacity Fire Bucket.

Supply, Fixing of 9 Ltr capacity Fire Bucket Stand for 4 Nos Bucket

Supplying and installation of iron removal Plant.

Supplying and installation of Reverse Osmosis filter.

Kanchan

Sonaru

Christmus tree

Ashoke

Radhasura

Krishnasura

Bakul

Dalia

Labour

Supplying, fitting and fixing stainless steel letters of size 16'' height including the cost of carriage and arrangement of fixing the letters on walls as directed by the Department ( The rate should be quoted for each letter and rate is inclusive of all Taxes as admissiable in the State.)

Providing and fixing white vitreous china extended wall mounting water closet of size 780x370x690 mm of approved shape including providing & fixing white vitreous china cistern with dual flush fitting, of flushing capacity 3 litre/ 6 litre (adjustable to 4 litre/ 8 litres), including seat.

Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating Single half stall urinal with 5 litre P.V.C. automatic flushing cistern .

Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required: White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin .

Providing and fixing one piece construction white vitreous china squatting plate with an integral longitudinal flushing pipe, white P.V.C. automatic flushing cistern, with fittings, standard size G.I. / PVC flush pipe for back and front flush with standard spreader pipes with fittings, G.I clamps and C.P. brass coupling Single squatting plate with 5 litre P.V.C. automatic flushing cistern

Constructing soak pit 1.20x1.20x1.20 m filled with brickbats including S.W. drain pipe 100 mm diameter and 1.20 m long complete as per standard design.

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings& accessories etc. 23.3.1:-100 mm nominal size dia

Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete. 100 mm dia Sand cast iron S&S as per IS - 1729

Providing and fixing single equal plain junction of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete. 100x100x100 mm Sand cast iron S&S as per IS - 1729

Constructing masonry Chamber 30x30x50 cm inside, in brick work in cement mortar 1:4 (1 cement :4 coarse sand) for stop cock, with C. I. surface box 100x100 x75 mm (inside) with hinged cover fixed in cement concrete slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal : With common burnt clay F.P.S.(non modular) bricks of class designation 7.5

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes 25 mm nominal dia Pipes.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes 18.7.5 40 mm nominal dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting ses and making good the walls etc. 15 mm nominal dia Pipes

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. 15 mm nominal bore

Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms. 15 mm nominal bore .

Providing and fixing PTMT pillar cock of approved quality and colour. 15 mm nominal bore, 125 mm long foam flow, weighing not less than 120 gms.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata All types of soil 300 mm dia

Supplying, assembling, lowering and fixing in vertical position in bore well, ERW (Electric Resistance Welded) FE 410 plain slotted (having slot of size 1.6/3.2 mm) mild steel threaded and socketed / plain bevel ended pipe (type A) 150 mm nominal size dia

Supplying, laying/ fixing, testing and commissioning of followingnominal sizes of chilled water piping plumbing inside the building (with necessary clamps, vibration isolators and fittings but excluding valves, strainers, gauges etc.) duly insulated with fire retardant quality expanded polystrene moulded pipe section of density 20 kg/cu.m after a thick coat of cold setting adhesive 100mm dia.(50mm thick insulation)

STRAINER of Ductile CI Body flanged ends with stainless steel strainer for chilled / hot water circulation including insulation as specified. 100 mm dia Each

Development of tube well in accordance with IS : 2800 (part I) and IS:11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor.

Supplying, fixing, testing and commissioning of condenser water pipes of following sizes of MS 'C' class along with necessary clamps, vibration isolators and fittings such as bends,tees etc.but excluding valves, strainers, gauges etc. adequately supported on rigid supports duly painted/buried in ground excavation and refilling etc. as per specification and as required complete in all 100mm dia.

BALANCING VALVE WITH BUILT IN MEASURING FACILITY with C I body flanged construction with EPDM coated disc with long pitch with protected out pipe insulation & PN 16 pressure rating for chilled / hot water circulation as specified. 100mm dia.

Wiring for circuit/submain wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in the surface/recessed medium class PVC conduit as required. 2 x 2.5 sq. mm + 1 x 2.5 sq. mm earth wire

2 x 4 sq. mm + 1 x 4 sq. mm earth wire

Supplying and fixing metal box of 150mm X 75mm X 60mm deep ( Normal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including providing and fixing 3 pin 5/6 A socket outlet and 5/6 A piano type switch, connections, painting etc. as required.

Supplying and fixing metal box of 180mm X 100mm X 60mm deep ( Normal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including providing and fixing 6 pin 5/6 & 15/16 A piano type switch, connections, painting etc. as required.

Network TDN IR outdoor Bullet camera, 4 Mega Pixel 2.8 to 12 mm, smart IR LED,s for 30mtrs Night vision, PoE.H.265

Network TDN IR indoor Bullet camera, 4 Mega Pixel 2.8 to 12 mm, smart IR LED,s for 30mtrs Night vision, PoE.H.265

16 C.H Network Video Recorder 4 SATA HDD Slot ( Max 08 TBx4), Real time Recording Resolution, Real time Local playback Multiplex operation. H.265 High profile BNCNGA/HDMI output Main profile baseline , HDD Redundancy free DDNS, Network backup USB Writer SATA Writer1 RS485, Support 18 kinds of PTZ protocol ONVIF 2.0 16 POF Port.

8 TB Surveillence Hard Disc Drive

32'' Professional LED Monitor with HDMI

16 Port Gigabit power over Ethernet switch 16 x RJ45 10/100/1000M ( Poe), 1 x Rj45/10/100/1000 2 SFP 180 Watt.

5 Port Gigabit power over Ethernet switch 5xRJ45

SFP 1000 Base LX/ LC Connector

Connector RJ45

9U Rack with all Accessories

Path Panel

Path Chord

PVC J Box For Camera

Cat-6 305 Mtr

4 Core Fibre Cable

1.5 Sqmm M/S 2 Core Cable

25 mm PVC with all necessary fittings.

Installation commissioning of all above camera, wire & all above accessories.

Supply and installation of Addressable Two Loop wire alarm control panel with capacity to connect 126 addressable device, LCD display, power supply units , Built in charger ( Batteries Excluded), EN 54 certified as per attached technical.

Supply and installation of Addessable Manual Call Point, Addressable Intelligent Manual call Point with in isolator LPCB Certified.

Supply and installation of Addessable Smoke detectors with base Addressable smoke detectors with mounting base LPCB certified.

Supply and Installation of response Indicator.

Supply and Installation of Addressable Sounds.

Supply and Installation of 1.5 sqmm 2 core FRLS armoured Cable.

20 Mtr High Mast Pole 01 Nos, panel Board 01 Nos, High Mast Light 14 Nos 200 Watt, Aviation Light 01 Nos, foundation 01 Nos, Freight & Carriage.

Testing, Lekage finding , repairing and commissioning of make packages units. 10 TR/R22

Vaccum of existing unit and testing with nitrogen gas for 24 hours

Supply & Installation of refrigerant gas R22 with suitable volume for the unit.

Dimental of existing drier in outdoor and supply & installation of new dryier in the outdoor unit.

Supplying, installing, testing, commissioning, interconnecting refrigerant copper pipe work with closed cell elasomeric nitrile rubber tubbler insulation between each set of indoor & outdoor units as per specifications, all piping inside the building shall be properly supported. 15.6 mm OD (5/8'')

Supplying, installing, testing, commissioning, rigid PVC piping complete with fittings, supports as per specifications and duly insulated with closed cell nitrile rubber Installation.

Supplying, installing, testing, commissioning of communication ns power cable from indoor to outdoor as per manufacturer recommendation.

Supply & Installation of Canvas Connection between unit & Duct.

Supply & Installation of site fabricated GI duct with Insulation.

Supply and Installation of soller system Havells make 60 watt AIO SSL.

20 KVA online UPS system isolation ( 3 Phase in 1 Phase out) , Exide make 12 volts 100Ah Battery 16 nos , Battery rack.

Supply, installation and commissioning of diesel engine driven stand by fire pump of capacity 2280LPM of 70 M head, including supply, installation, testing, commissioning of required HP/BHP Diesel Engine with coupling and coupling guard, M.S Baser plate/ Base Frame, Cushy foot mounting, foundation Bolts, including 200Fuel Tank 12-V-21 plate battery and Silencer. Make KIRLOSKAR PUMP, KOEL/CUMINS-ENGINE.

Supply, installation and commissioning of Electric motor driven jockey pump of capacity 180 LPM of 70 M head complete with M.S Base plate/ Base Channel, coupling and coupling guard, Cushy foot mounting, foundation Bolts etc. and also including 3 phase Motor of 415 volts of required HP/KW (WITH + 10%) Variation , 3 phase 2900 RPM TEFC MOTOR Mounted on common base , frame, complete with all accessories Make KIRLOSKAR PUMP/ CROMPTON GREAVES-MOTOR, or equivalent.

Supply, installation and commissioning of Electric motor driven pump of capacity 2280 LPM of 70 M head complete with M.S Base plate/ Base Channel, coupling and coupling guard, Cushy foot mounting, foundation Bolts etc. and also including 3 phase Motor of 415 volts of required HP/KW (WITH + 10%) Variation , 3 phase 2900 RPM TEFC MOTOR Mounted on common base , frame, complete with all accessories Make KIRLOSKAR PUMP/ CROMPTON GREAVES-MOTOR, or equivalent.

Supply, installation and commissioning of FRLS, PVC outer sheathe, steel armoured, aluminium/copper conductor, 1100V grade power cables with glands etc. The cable shall be laid in tray/ hume pipe/ in trenches/ on walls floor etc as required. For cables laid out for the rate shall include earth excavation providing brick and sand protection , refilling and compacting the earth . The rate shall excludes tray & Hume pipes. The minimum of of the cable shall be mentioned as below a 3C X 16sq mm AL, PVC Armoured Cable ( Jockey PUMP).

b 3C X 95 sq mm AL, XLPE ARM Cable ( Fire Panel to Main Pump)

c 12 C X 2.5 sq mm Cu, PVC Armoured Cable ( Control Cable)

d 2C X 1.5 sq mm copper armoured for installation of pressure switch.

Supply, Installation & testing of GI earth station with perforated 40 mm dia and 4.50 Metre long heady duty GI pipe with necessary 40 mm dia GI fitting such as socket, Tee, Elbow, nipple and 50 mm X 40 mm GI reducing socket for funnel including locking arrangements 300 mm X 300 mm X 6 mm hinged cover CI earth plate complete with digging of earth pit, construction of brick chember and plastering of both inner & outer surface of wall as specified and directed by the deptt.

Supplying & Laying of SWG GI earth drawn through 15 mm dia. Medium quality GI pipe from earth Electrode( Below GI) to electrical switch gears or electrical machineries including making necessary connection as approved, specified and directed by the deptt.

M/S I.S. Trading Co.