Renovation and repairing of mortuary building at RIMS, Imphal

Amount

Excavation in Hard Rock (blasting prohibited) (Excavation for roadwork in hard rock (blasting prohibited) with hydraulic excavator including cutting and loading in tipper, trimming bottom and side slopes in accordance with requirements of lines, grades and cross sections and transporting to the embankment location within all lifts and lead upto 1000 meters, .)

A Mechanised

1 Granular Sub-Base with Close Graded Material (Table:- 400-1)

A Plant Mix Method

Construction of granular sub-base by providing close graded Material, mixing in a mechanical mix plant at OMC, carriage of mixed Material to work site, spreading in uniform layers with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per clause 401 .

Grading-II Material

Providing and laying factory made cement concrete interlocking paver block of M-30 grade made by block making machine with strong vibratory compaction,of approved size,design & shape,laid in required colour and pattern over and including 50 mm thick compacted bed of coarse sand,filling the joints with fine sand etc.all complete as per the direction of engineer-in-charge

80 mm thick

Earth work in excavation by mechanical means (Hydraulic Excavator )/ manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.

All kinds of soil.

Demolishing lime concrete manually/ by mechanical means and disposal of material within 50 metres lead as per direction of Engineer in charge.

Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix)

Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved.

Dismantling roofing including ridges, hips, valleys and gutters etc., and stacking the material within 50 metres lead of:

G.S. Sheet

Hacking of CC flooring including cleaning for surface etc. complete as per

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - -All work upto plinth level:

1:4:8 ( 1 Cement: 4 coarse sand : 8 graded stone aggregate 40 mm nominal size)

Reinforcement for R.C.C. work including straightening, cutting, bending,placing in position and binding all complete. Above Plinth level

Thermo-Mechanically Treated bars

Centering and shuttering including strutting, propping etc. and removal of form for:

a)Foundation, footings, bases of columns etc. and mass concrete.

Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centering, shuttering, finishing and reinforcement - All work upto plinth level

1:2:4 (1 cement: 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers,abutments, posts and struts etc. up to floor five level excluding cost of centering,shuttering, finishing and reinforcement :

1:1.5:3 (1 cement: 1.5 coarse sand: 3 graded stone aggregate 20 mm nominal size).

Chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard jointed with neat cement slurry mixed with pigment to match the shade of tiles including rubbing and cleaning etc. complete on 20 mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand).

Light shade using white cement.

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption’s less than 0.08% and conforming to IS : 15622 of approved make in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement: 4 coarse sand) including grouting the joints with white cement and matching pigments etc., complete.

Size of Tile 600 x 600 mm

Providing and laying rectified Glazed Ceramic floor tiles 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS :15622 of approved make in all colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick Cement Mortar 1:4 (1 Cement : 4 Coarse sand) including pointing the joints with white cement and matching pigments etc., complete.

wash room

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption’s less than 0.08% and conforming to IS : 15622 of approved make in all colours and shades, in skirting,riser of steps,over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand)jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc., complete.

Size of Tile 600 x 600 mm

Half brick masonry with Ist class common burnt clay F.P.S. (non modular) bricks in superstructure above plinth level upto floor V level in

Cement mortar 1 : 3 (1 cement : 3 coarse sand)

Providing and fixing tiled False Ceiling of approved materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanised steel sections ( galvanized @ 120 gsm/sqm, both side inclusive) consisting of main “T” runner with suitably spaced joints to get required length and of size 24x38mm made from 0.30mm thick (minimum) sheet, spaced at 1200mm center to center and cross “T” of size 24x25mm made of 0.30mm thick (minimum) sheet, 1200mm long spaced between main “T” at 600mm center to center to form a grid of 1200x600 mm and secondary cross “T” of length 600mm and size 24x25mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600mm panel to form grids of 600x600mm and wall angle of size 21x21x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main “T” runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x 1.6 mm fixed to ceiling with 12.5 mm dia and 50mm long dash fasteners, 4mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200mm center to center along main T, bottom exposed width of 24mm of all T-sections shall be pre-painted with polyester paint, all complete at all heights as per specifications, drawings and as directed by Engineer- in-Charge. (The rate is excluding the cost of tiles which will be paid

GI Metal ceiling Lay in plain Tegular edge Global white color tiles of size 595 x 595 mm, and 0.5 mm thick with 8 mm drop, made of GI sheet having galvanizing of 100 gms/sqm( both sides inclusive) and electro statically polyster powder coated of thickness 60 microns (minimum), including factory painted after bending.

Providing and fixing aluminium work for doors, windows, ventilators and partitionswith extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS : 1285, fixed with rawl plugs and screws or with fixing clips, or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom and sides with required EPDM rubber/ Neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleatangle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steelscrews, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing and panelling to be paid for separately):

For fixed portion.

Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber/neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):

With float glass panes of 4.0 mm thicknes

Cement plaster 1:3 (1 cement: 3 coarse sand) finished with a floating coat of neat cement.

12mm cement plaster.

Providing and applying white cement based putty of average thickness 1mm,of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface :

Water thinnable cement primer

Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade. ( Two or more coats on new work)

Providing wood work in frames of doors, windows, clerestory windows and other frames,wrought framed and fixed in position with hold fast lugs or with dash fastener of required dia and length (hold fast lugs or dash fastener shall be paid for separately :

Local best quality Uningthou wood

Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows including ISI marked M.S butt hinges bright finished of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge.

Local best quality Tolhao wood.

35 mm thick shutters

Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required :

W.C. pan with ISI marked white solid plastic seat and lid.

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required:

White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar tap

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.

Flexible pipe

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing :

Rectangular shape 453x357 mm

Providing and fixing brass bib cock of approved quality

25 mm nominal bore

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge.

Concealed work, including cutting chases and making good the wall etc.

25 mm nominal outer dia Pipes

Providing and fixing UPVC soil,waste,rain water and vent pipes including all requisite fittings,jointing of pipes & fittings with solvent cement trenching,refilling & testing of joints complete as per direction of engineer in charge

110 mm dia

Providing and fixing bright finished brass single acting spring hinges with necessary screws etc. complete :

Providing and fixing aluminium sliding door bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete

Steel work in built up tubular (round, square or rectangular tubes etc.) trusses etc., including cutting, hoisting fixing in position and applying a priming coat of approved steel primer, including welding and bolted including special shaped washers etc. complete.

Electric resistance or induction butt welded tubes.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal,complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required with

Precoated galvanised iron profile sheets 0.40 mm thick

Taking out doors, windows and clerestory window shutters (steelor wood) including stacking within 50 metres lead:

Dismantling old plaster or skirting raking out joints and cleaningthe surface for plaster including disposal of rubbish to thedumping ground within 50 metres lead.

Dismantling wood work in frames, trusses, purlins and rafters upto 10 metres span and 5 metres height including stacking thematerial within 50 metres lead :

Extra for dismantling trusses, rafters, purlins etc. of wood work forevery additional height of one metre or part thereof beyond 5metres

Providingandlayinginpositioncementconcreteofspecifiedgrade excluding the cost of centering and shuttering --All work upto plinth level:

1:5:10 ( 1 Cement: 5 coarse sand : 10 graded stone aggregate 40mm nominal size)

Brick work with Ist class common burnt clay F.P.S.(non modular) bricks in foundation and plinth in:

Cement mortar 1:4 (1 cement : 4 coarse sand)

Providing and fixing 18mm thick gang saw cut mirror polished(premoulded and prepolished ) machine cut for kitchen platforms,vanity counters ,window sills , facias and similar locations of required size of approved shade, colour and texture laid over 20mm thick base cement mortar 1:4 (1 cement : 4 coarse sand)with joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing moulding and polishing to edge to give high gloss finish etc. complete at all levels. Granite of any colour and shade

Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30x10 x 15cm 1:3:6 mix (1cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size)

Providing wood work in frames of doors, windows, clerestory window sand other frames, wrought framed and fixed in position with hold fast lugs or with dash fastener of required dia and length (hold fast lugs or dash fastener shall be paid for separately : Local best quality Tolhao wood.

Providing and fixing panelling or panelling and glazing in panelledor panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portioninside grooves or rebates to be measured). Panelling for panelledor panelled and glazed shutters 25 mm to 40 mm thick :

Providing and fixing panelling or panelling and glazing in panelledor panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelle dor panelled and glazed shutters 25 mm to 40 mm thick :

4 mm thick glass panes

Providing wood work in frames of false ceiling, partitions etc.sawn and put up in position :

Local best quality Uningthou wood

Providing and fixing aluminium sliding door bolts ISI markedanodised (anodic coating not less than grade AC 10 as per IS :1868) transparent or dyed to required colour or shade with nutsand screws etc. complete :

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade with necessary screws etc. complete :

Providing and fixing aluminium handles, ISI marked,anodised(anodic coating not less than grade AC 10 as per IS : 1868)transparent or dyed to required colour or shade with necessaryscrews etc. complete :

Providing and fixing 20mm plank as eave board with :-

Tolhao/Uchan wood.

62 mm thick cement concrete flooring with concrete hardenertopping under layer 50 mm thick cement concrete 1:2:4 (1cement : 2 coarse sand : 4 graded stone aggregate 20mm nominalsize) and top layer 12mm thick cement hardener consisting of mix1:2(1 cement hardener mix : 2 graded stone aggregate 6mmnominal size) by volume. Hardening compound is mixed @ 2 litreper 50kg of cement or as per manufactures specifications. Thisincludes cost of cement slurry,but excluding the cost of nosing ofsteps etc. complete.

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption’s less than 0.08% and conforming to IS : 15622 of approved make in all colors and shades, laid on 20mm thick cement mortar 1:4 (1 cement: 4 coarse sand) including grouting the joints with white cement and matching pigments etc., complete.

Providing corrugated G.S. sheet roofing including vertical/curvedsurface fixed with polymer coated J or L hooks, bolts and nuts 8mm diameter with bitumen and G.I. limpet washers or with G.I.limpet washers filled with white lead and including a coat of approved steel primer and two coats of approved paint onover lapping of sheets complete upto any pitch in horizontal / vertical or curved surfaces) excluding the cost of purlins, raftersand trusses and including cutting to size and shape wher ever required.

0.8mm thick with zinc coating not less than 275gm/m2

Providing ridges or hips of width 60 cm over all width plain G.S.sheet fixed with polymer coated J. or L hooks, bolts and nuts 8 mmdia. G.I. limpet and bitumen washers complete.

0.80mm thick with zinc coating not less than 275gm/m2

Providing valleys of 90cm wide overall in plain G.S. sheet fixed withpolymer coated J, or L hooks, bolts and nuts 8mm dia.. G.I. limpetand bitumen washers complete :

1.60mm thick with zinc coating not less than 350gm/m2

Providing and fixing insulating board ceiling of approved quality with necessary nails etc.complete (framework to be paid separately):

Standard quality hard board sheet:

4.5 mm thick

12 mm cement plaster of mix

1:4 (1 cement : 4 coarse sand)

Providing and applying white cement based putty of average thickness 1mm,of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Neat cement punning

Applying priming coats

With water thinnable cement primer on wall surface having VOCcontent less than 50 grams/litre

Wall painting with acrylic emulsion paint, having VOC (VolatileOrganic Compound ) content less than 50 grams/ litre, of approvedbrand and manufacture, including applying additional coatswherever required, to achieve even shade and colour.

Two coat

Providing and fixing water closet squatting pan (Indian typeW.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre lowlevel white P.V.C. flushing cistern, including flush pipe, withmanually controlled device (handle lever) conforming to IS :7231, with all fittings and fixtures complete, including cuttingand making good the walls and floors wherever required:

White Vitreous china Orissa pattern W.C. pan of size 580 x 440mm with integral type foot rests

Providing, fixing and jointing of PVC septic tank of 1000ltr capacity of approved quality i/c fitting, fixing, placing in position, backfilling the excavated soil all complete as per the specification given the Engineer-in-charge, excluding the cost of earth excavation, laying of lean concrete, and sand cushioning.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge.

External work

75mm nominal outer dia Pipes

SOCIAL SATISFACTORY CONSTRUCTION & SUPPLIER (BID ID -3158724)

Y.DEVENDRO SINGH (BID ID -3158711)