WORK SERVICES FOR CLEANING OF E/M INSTALLATION CUTTING OF VEGETATION, BUSHES, GRASS, CREEPER ETC, REPAIR/MAINT OF BUILDING SECURITY LIGHTS AND CONNECTED WORK IN VARIOUS ACCOMMODATIONS IN OMQ/SMQ AREA AND REPAIR/MAINT INCLUDING PERIODIC TESTING OF EAR

Amount

S&F in replacement of first aid kit box/emergency medical box wall mouted type made out of powder coated GI sheet of 18 gauge and the size of the box will be 36cm(H) x 26cm(W) x 13 cm(D) with front transparent acrylic glass and multi compartment 4 shelf for better organize of medicines with security lock on door, openable window at front side with help of hinge at one side and locking arrangement at another side, openable window must painted with "FIRST AID" with red paint and whole box will fixed on wall at height not less than 2mtr including medicene and other items as under :- (i) Sterilized dressings- 04 Nos, (ii) Cotton Wool 10 gm - 02 Nos, (iii) Antiseptic Solution (100 ml) - 01 No, (iv) Burn Ointment - 01 No, (v) Scissor - 01 No, (vi) Digital Thermometer - 01 No, (vii) Disposal Gloves - 02 Nos, (viii) Disposal Mask - 20 Nos, (ix) Adhesive / Microporous Tape 1/2" - 01 No, (x) Band- Aid - 10 Nos, (xi) Safety pins - 05 No, (xii) Cold Rub - 01 No, (xiii) Roller Bandage (5cm) - 02 Nos, (xiv) Roller Bandage 10 cm - 02 Nos, (xv) Cotton Buds - 10 Nos, (xvi) Hand Sanitizer - 02 Nos, (xvii) Handiplast - 12 Nos, (xviii) Antiseptic cream - 01 No, (xix) Antiallergic medicene, Cough medicene, Pain killer, Fever and cold medicene- 01 strip each and a First-Aid Guide booklet, complete all as specified and directed.

Uprooting grass/weeds/plants up to 30cm depth by scrapping soil in order to make free ground from all sort of vegetation (grass/weeds/plants) and hand packing carefully by packing round pebbles approximately of size 20 to 40mm after carefully picking form heap of pebbles/stones, complete all as specified and directed.

Cleaning of area around E/M sub division by scraping the grass and creepers from roof and spraying grass killing chemical with spray gun, as per manufacturer's instructions for prevention of weeds and grass at surrounding of E/M sub station area, complete all as specified and directed.

Supply and spreading unslaked lime at surrounding (avarage 300 gms per Sqm), complete all as specified and directed.

Supply and filling dry river sand at surrounding of E/M installations / sub stations /cable trenches including watering and consolidation, complete all as specified and directed.

Supply and filling crushed stone aggregate, free from any foreign particles, 25mm gradded, for spreading at E/M sub station area, complete all as specified and directed.

Demolition of brick work or stone/ boulder masonry, built in cement mortar including all quoins, pillars, manholes etc., separation of serviceable materials from the unserviceable, stacking the serviceable materials within 100m and disposal of unserviceable materials, debris and rubbish to a distance not exceeding 100m, complete all as specified and directed.

M&L for brick work with fly ash bricks, old size, straight or curved on plan exc 6 mtr mean radius built in CM (1:6) including demolition of brick work, complete all as specified and directed.

M&L for rendering 15mm thick on fair faces of brick work or concrete surfaces in CM (1:6) and finished even and smooth without using extra cement, complete all as specified and directed.

M&L for preparation of newly plastered surfaces of wall and applying three coats of white wash, complete all as specified and directed.

M&L for complete removal of existing treatment of old painted steel or iron surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint (1st grade quality), complete all as specified and directed.

Demolition of cement concrete un-reinforced in ground floors and pavings n. exc. 15cm thickness (below or above ground level), complete all as specified and directed.

M & L for PCC (1:2:4) type B-1 (using 20mm graded crushed stone aggregate) as in coping/benching/foundation of columns, filling and mass concrete etc, complete al as specified and directed.

M&L 75mm thick PCC (1:3:6 ) type C-2, (using 40mm graded stone aggregate) for sub base of floor, plinth prtection, path/hard standing etc, complete all as specified and directed.

M&L for PCC (1:3:6) type C-1 (using 20mm graded crushed stone aggregate) as in coping of poles, etc. including necessary formwork (as required), complete all as specified and directed.

M&L for mild steel chequered plate Fe-290 (Grade-E-165) 5mm or over thickness confirming to IS 1730-1981 as in duct covering placed over existing angle iron frame work or provision new frame work where necessary including connection of suitable number earth strip welded properly and making good to th existing surface of duct, complete all as specified and directed.

Supplying and laying synthetic rubber insulated mats 2mm thick for voltage upto 3.3 kv for electrical purpose as per IS 15652-2006, (superseding IS 5424) suitable for electrical shock safety, complete all as specified and directed.

M&L for earthing complete with GI earth plate electrode 60 × 60cm × 6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less'than 1.5 metres below normal ground level, connected to existing earth lead strip by means of bolts, nuts, check nuts and washers of brass or HS steel all as shown in electrical plate No. 3 connected to earthing test point and and necessary excavation and earth work PCC (1:3:6) type C-1 as earth pit with pre-cast RCC (1:2:4) type B-1 cover slab size 400 x 400 x 50mm reinforced with 8mm dia TMT bar, 100mm c/c both ways including one handle made of 12mm dia including providing charcoal or coke and common salt in alternate layer of 15cm compacted thickness all around the earth electrode with funnel and 20mm bore galvanized iron watering pipe (light grade) wire mesh, copper lugs, complete in all respect, including galvanised iron earth strip 25 x 4mm, protected by 40mm bore (medium grade) galvanized iron pipe up to earthing test point as directed, incl disposal of spoil to a distance not exc. 50 mtr and necessary testing on completion, complete all as specified and as directed. Note : (i) Proper earthing pit should be provided with pit cover. (ii) GI earth strip beyond 7.5 mtr shall be measured and paid seperately.

S&F post top lantern LED type 20/25 watt AC 230 volts outdoor type with decorative post top for 360 degree indirect light IP 65/66 protection with impact and corrosion resistant complete with driver and lamp, complete all as specified and directed.

S&F post top lantern LED type 35 watt AC 230 volts outdoor type with decorative post top for 360 degree indirect light IP 65/66 protection with impact and corrosion resistant complete with driver and lamp, complete all as specified and directed.

S&F post top lantern LED type 40 watt AC 230 volts outdoor type with decorative post top for 360 degree indirect light IP 65/66 protection with impact and corrosion resistant complete with driver and lamp, complete all as specified and directed.

S&F in replacement bldg security light fitting LED type, 60 watt with all necessary accessories, clear transparent acrylic cover, prewire suitable to operated on 230 volt 50 HZ AC fixed to wall/ on pole including fixing arrangement with galvanized iron pipe 35mm bore, light grade, brackets, 2 mtr length, bent to shape to obtained required shape including clamps, nuts / bots / washers etc connecting with suitable flexible copper wire of size 23/0.0076, complete all as specified and directed

Cleaning of vegetation, bushes, creepers etc, spread over the electric outdoor appliance and electric poles upto maximum height 8m including removal of vegetation from the depth of 30cm and area upto 3m radious from electrical appliance, complete all as specified and directed.

Supply, fabricating, installation, testing and commissioning of back-fit signage board including embedding the board firmly with the wall/MS angle frame/as per approved art work and nomenclature as under :- Box with frame :- 25 x 25mm square pipe (18 gauge) frame with cross supports @ spacing not exceeding 1.0m on the box length including 20mm x 20mm MS Square pipe (18 gauge) stiffeners duly painted with two coats of white synthetic enamel paint (1st grde quality) over a coat of zinc oxide iron primer, depth of box should not be less than 165mm. Side, Top, Back and bottom Panels :- Made out of 24 gauge chemically treated GI Sheets duly powder coated with white matt finish coating on both inner and outer surfaces. Top panel made out of 24 gauge chemically treated GI sheet, duly powder coated, drip cap (fixed with pop rivet or machine moulded to shape) of 25mm on front and side to prevent damages due to rain etc. The bottom panel should be provided with access door fixed with stainless steel screws and suitable housing for LED drivers. LED Module :- LED 12V module beam angle >=150 degrees with IP rating >= 64, 0.72 W/70 lumens per module of 3 LEDs with 7000 to 8000 K colour temperature. LED configuration :- 29 LED modules per Sqm (equal division on spacing based on height of box) and one module every 0.20 m on running length of box. LED power supply :- Input 230 V AC, power supply should be CPCC (constant power constant current) of 30W/60W/120 W. Graphics :- Graphics shall be computer plotter cut with translucent cast vinyl matching the colour specification of the installation.

Dismantling the strip from earth pit and testing of earth pit to be done as per fall of potential method mentioned in IS-3043 with digital earth resistance tester to check the healthiness of earthing system in and including replacement earth pit nut bolts with brass nut bolts as per required size and record should be kept on ledger duly signed by JE concerned and contractor and the same shall be submitted to Engr- in-charge for counter signature, complete all as specified and directed. Note : (i) Testing of earth pit shall be done as and when required basis or as directed by Engineer-in-Charge from time to time. (ii) Testing of each earthing shall be carried out at the interval of 1 months and measurement shall be done each time separately and test result shall be maintained in register properly duly signed with date by MES representative and contractor jointly. (iii) Pouring of water in each earth pit is deemed to be included in the unit quoted rate. (iv) Necessary arrangement to be made by the contractor for pouring the water in earth pits. vehicle reqd for carrying/storage of water (upto to the site) with helper will be arranged by contractor and deemed to be included in the unit quoted rate. (v) Cost of maintenance of carrying vehicle (if any) and cost of fuel reqd for veh is deemed to be included in the unit quoted rate.

M&L for earthing complete with GI earth plate electrode 60 × 60cm × 6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less'than 1.5 metres below normal ground level, connected to existing earth lead strip by means of bolts, nuts, check nuts and washers of brass or HS steel all as shown in electrical plate No. 3 connected to earthing test point and and necessary excavation and earth work PCC (1:3:6) type C-1 as earth pit with pre-cast RCC (1:2:4) type B-1 cover slab size 400 x 400 x 50mm reinforced with 8mm dia TMT bar, 100mm c/c both ways including one handle made of 12mm dia including providing charcoal or coke and common salt in alternate layer of 15cm compacted thickness all around the earth electrode with funnel and 20mm bore galvanized iron watering pipe (light grade) wire mesh, copper lugs, complete in all respect, including galvanised iron earth strip 25 x 4mm, protected by 40mm bore (medium grade) galvanized iron pipe up to earthing test point as directed, incl disposal of spoil to a distance not exc. 50 mtr and necessary testing on completion including dismantling of old unserviceable earthing of any description, complete all as specified and as directed. Note : (i) Proper earthing pit should be provided with pit cover. (ii) GI earth strip beyond 7.5 mtr shall be measured and paid seperately.

S & F in repair for GI strip of size 25 x 4mm with saddles and fixing screws etc. for roof conductors with rubber & bitumen washer & fixed to porcelain insulator on wall for down conductor including taking down old unserviceable copper strip of any size, complete all as specified and directed

S & F in repair for GI wire earth continuity conductor or main earthing lead size 4 Sqmm fixed to wall on batten or recess or chase or buried in ground or drawn in conduit/pipe or fixed to pole or other indicated situation for loop earthing etc, complete all as specified and directed

S & F 40mm bore galvanized steel tubes, 'light grade' ISI marked with all fitting and fixed complete to roof slab / walls / pavement/ ceilings or laid on floors, including taking down old unserviceable pipes, complete all as specified and directed.

S & F 20mm dia PVC conduit, rigid, non metalic, exclusive of boxes but inclusive of all tees, bends, elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hooks etc, complete all as specified and directed.

S & F for porcelain insulator suitable for fixing of aluminim/copper strip on roof/wall with necessary drilling and providing two Nos screw for each insulator, complete all as specified and directed.

Checking the earth resitance of existing copper/GI plate earthing by meggar and repair/replacement of strips where found corroded and testing of earth resistance value and providing magnesium sulphate and salt (minimum 8 kg per earthing) to achieve required earth resistance value, complete all as specified and directed. Note: Replacement of strip if required, shall be measured paid separately under relevant items.

M &L for eathing pit in PCC (1:3:6) type C1 pre-cast RCC (1:2:4) type B-1 cover slab of size 400 x 400 x 50mm reinforced with 8mm dia TMT steel bars @ 15 cm center to center in both direction and 10mm dia MS handle of suitable size including 29 mm bore GI light grade pipe for watering, funnel, wire mesh, necessary earth work in soft / loose soil all as shown in Electrical plate No 4 of MES schedule Part -I (2009) and testing and applying three coats of white wash on exposed surface of concrete complete including taking down old one, complete all as specified and directed.

S&F LED street light fittings 70/72 watt 230 v AC outdoor type with high pressure dia cast aluminium housing and heat-resistant complete with driver, lamp bracket with impact and corrision resistant, IP 65/66 protection including taking down old unserviceable LED light fittings, complete all as specified and directed.

S&F LED street light fittings 60 watt 230 v AC outdoor type with high pressure dia cast aluminium housing and heat-resistant complete with driver, lamp bracket with impact and corrision resistant, IP 65/66 protection including taking down old unserviceable LED light fittings, complete all as specified and directed.

S&F LED street light fittings 45 watt 230 v AC outdoor type with high pressure dia cast aluminium housing and heat-resistant complete with driver, lamp bracket with impact and corrision resistant, IP 65/66 protection including taking down old unserviceable LED light fittings, complete all as specified and directed.

S&F LED flood light 50/60 watt 230 V AC outdoor type with thermal management in multiple optics and equipped with IP 65/66 protection, with impact and corrosion resistant complete with driver and lamp including taking down old unserviceable flood light, complete all as specified and directed.

S&F LED flood light 100 watt 230 V AC outdoor type with thermal management in multiple optics and equipped with IP 65/66 protection, with impact and corrosion resistant complete with driver and lamp including taking down old unserviceable flood light, complete all as specified and directed.

S&F LED flood light 120 watt 230 V AC outdoor type with thermal management in multiple optics and equipped with IP 65/66 protection, with impact and corrosion resistant complete with driver and lamp including taking down old unserviceable flood light, complete all as specified and directed.

S&F LED flood light 150 watt 230 V AC outdoor type with thermal management in multiple optics and equipped with IP 65/66 protection, with impact and corrosion resistant complete with driver and lamp including taking down old unserviceable flood light, complete all as specified and directed.

S & F in repair cable, 3 core, PVC insulated unsheathed multistranded copper conductor cable of size 1.5 Sqmm passing through PVC conduit from junction box to fitting, complete all as specified and directed. Note : PVC conduit shall be measured and paid seperately.

S & F in repair cable, 3 core, PVC insulated unsheathed multistranded copper FR conductor cable of size 2.5 Sqmm passing through PVC conduit from junction box to fitting, complete all as specified and directed. Note : PVC conduit shall be measured and paid seperately.

S&F in repair driver for outdoor type LED fitting 30/35 Watt, complete all as specified and directed.

S&F in repair driver for outdoor type LED fitting 45 Watt, complete all as specified and directed.

S&F in repair driver for outdoor type LED fitting 60/75 Watt, complete all as specified and directed.

S&F in repair driver for outdoor type LED fitting 90/120/150 Watt, complete all as specified and directed.

S&F street light bracket made out of 40mm bore, galvanised iron, medium grade tubing (approx 1.2 mtr in length) including two nos suitable size clamps with nuts, bolts and washers, etc. including painting with two coats of synthetic enameled paint (1st grade quality) over a coat of red oxide primer including taking down old unserviceable one, complete all as specified and directed.

S&F in repair LED bollard light 9/10 watt with soft 360 degree light distribution, IP-65/66 protection, inverted pyramid tripod type with PCC & fixing all ecessary arrangement, complete all as specified and directed.

S&F in repair 3 pole power contactors, 70 Amp, ML- 3, 2 NO+2 NC power contactors for street light and connecting new contactors and making connection with incoming and outgoing MCCB/MCB including taking down old unserviceable panel, complete all as specified and directed

S&F in replacement timer for 24 hrs, complete all as specified and directed.

Note: An amount of Rs.39,050.00 on account of Credit Schedule for schedule 'A' part - II shall be deducted from the total amount of BOQ to arrive at the contract sum.

M/S BIJAY KUMAR SHIVA (BID ID -3357663)

M/S SARDAR MAL NAHATA (BID ID -3357674)

M/S. NARENDRA KUMAR GARG (BID ID -3357675)