AGE I CGN 26 22 23 REPAIR OF PUMP MOTOR STARTER PANEL SUMP CLEANING AND OTHER ALLIED WORKS UNDER AGE I CG NOIDA

Amount

Excavation in trenches not exceeding 1.5 mtr wide and not exceeding 1.5 m in depth and getting out in soft/loose soil for laying of pipe , all complete as specified and directed.

Returning filling in trenches including spreading, leveling, watering and well ramming in layers not exceeding 25 cm thick in soft/loose soil compete all as specified and directed.

Removal of excavated surplus soil to a distance not exceeding 50 mtr and depositing where directed at level not exceeding 1.5 mtr above the starting point all as directed by Engineer-in-Charge.

Taking up or down galvanised water tubing (medium grade) with all fitting from trenches/ walls/ floors/ ceilings and separating serviceable pipes and fittings for reuse in the work and removing unserviceable pipes and fittings from site of 20 mm bore tubing including removing rusted MS clamps from walls etc.(where necessary),complete all as specified and directed.

All as per item No.4 here-in-before but 25 mm bore tubing.

All as per item No.4 here-in-before but 40 mm bore tubing.

All as per item No.4 here-in-before but 50 mm bore tubing.

Taking up or down galvanised water tubing (medium grade) with all fitting from trenches/ walls/ floors/ ceilings and separating serviceable pipes and fittings of dia 80 mm bore tubing.

All as per item No 8 here-in-before but 100 mm bore tubing.

Supply and lay galvanised steel water tubing (medium grade) complete with all fittings, laid in trenches, including testing for 20 mm bore tubing, complete all as specified and directed.

All as per item No.10 here-in-before, but 25 mm bore tubing.

All as per item No.10 here-in-before, but 40 mm bore tubing.

All as per item No.10 here-in-before, but 50 mm bore tubing.

All as per item No.10 here-in-before, but 80 mm bore tubing.

All as per item No.10 here-in-before, but 100 mm bore tubing.

Supply and lay galvanised steel water tubing (medium grade) complete with all fittings, fixed to wall and ceiling or laid in floors, including testing for 20mm bore tubing, including replace the rusted MS clamps on walls/ ceilings etc. complete all as specified and as directed.

All as per item No 16 here-in-before, but 25mm bore tubing.

All as per item No 16 here-in-before, but 400mm bore tubing.

All as per item No 16 here-in-before, but 50 mm bore tubing.

All as per item No 16 here-in-before, but 80 mm bore tubing.

S & F in repair Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixing 20mm dia, complete all as specified and directed. (Note: The quoted rate is deemed to be inclusive of cutting, threading, insertion of union joint, nipple etc for the required size of pipe.)

All as per item No 21 here-in-before, but 25mm dia .

All as per item No 21 here-in-before, but 40mm dia .

All as per item No 21 here-in-before, but 50mm dia .

S & F in replacement butter fly Valve Lever operated CI 65 mm bore tubing.

S & F in replacement of gate valves (Gun metal globe valve) with iron wheel head, screwed both ends for iron pipe and fixed for 15 mm dia, complete all as specified and directed. (Note: The quoted rate is deemed to be inclusive of cutting, threading, insertion of union joint, nipple etc for the required size of pipe)

All as per item No 26 here-in-before, but 20mm dia.

All as per item No 26 here-in-before, but 25mm dia.

All as per item No 26 here-in-before, but 40mm dia.

Dismantling of old unserviceable water tanks of capacity exceeding 250 ltrs and not exceeding 500 ltrs and removing from sitecomplete all as specified and directed.

Dismantling of old unserviceable water tanks of capacity exceeding 500 ltrs and not exceeding 1000 ltrs and removing from sitecomplete all as specified and directed.

Supply, hoisting and fixing of multilayer, rotational moulded polyethylene water storage tank of capacity 500 ltrs (cylindrical vertical with closed top) in existing position including necessary connections of pipes, complete all as specified in SSR Part-I and as directed.

All as per item No.32 here-in-before, but of 1000 ltr capacity.

M&L for cleaning of water supply under ground sump of capacity 40,000 gallons capaity by balling out the accumulated water at the bottom and removing the complete silt and disposing levelling as directed and cleaning with bleaching powder and wire brush after scrapping the walls and bottom of the sump complete including white washing inside and one coat of cement based paint on out side surface of sump without disturbing the water supply to the area and painting for the capacity and date of cleaning of sump in dd/mm/yyyy in bold capital letters of and including painting to air vent pipes, ladders, valve pit covers and covering mosquitoes proof complete all as specified and as directed by the Engineer-in-Charge.

M&L for cleaning of water supply under ground sump of capacity 50,000 litre capaity by balling out the accumulated water at the bottom and removing the complete silt and disposing levelling as directed and cleaning with bleaching powder and wire brush after scrapping the walls and bottom of the sump complete including white washing inside and one coat of cement based paint on out side surface of sump without disturbing the water supply to the area and painting for the capacity and date of cleaning of sump in dd/mm/yyyy in bold capital letters of and including painting to air vent pipes, ladders, valve pit covers and covering mosquitoes proof complete all as specified and as directed by the Engineer-in-Charge.

S&F in replacement sluice valve of type PN-1.6 and size 80mm dia with gun metal raising spindle, both ends flanged, with iron wheel head conforming to IS-14846-2000, and drilled with necessary holes for bolts including jointing material viz nuts, bolts, rubber gaskets etc , complete all as specified and directed.

All as per item No.36 here-in-before, but 100 mm dia

S & F in replacement Non return sluice valves with screwed both ends for Galvanised iron pipe and fixed for 80 mm dia, complete all as specified and directed. (Note: The quoted rate is deemed to be inclusive of cutting, threading, insertion of union joint, nipple etc for the required size of pipe)

M & L for PCC 1:3:6 type C2 (using 40 mm graded crushed stone aggregate) as in base foundation of pillar etc, complete all, as specified and directed.

Supply and fix in repairs CI flanged foot valve suitable for 100 mm dia pipe complete with necessary bolts, nuts, gasket etc. all as specified and directed by Engineeer-in-Charge. Make: KIRLOSKAR / L&T / VENUS

Supply and fixing in replacement Foot valve 80mm Dia with washer , gasket nut bolt strainer complet all as directed and specified by the Engr- in - Charge

Supply and fixing in replacement Foot valve 65 mm Dia with washer , gasket nut bolt strainer complet all as directed and specified by the Engr- in - Charge

M & L for construction of brick masonry valve pit with sub-class 'B' brick built in cement mortar (1:6), of size (100 x 100 x 100) cm (internal dimension) with one brick walling and 150 cm x 150 cm x 10 cm base foundation with PCC (1:3:6), type C2 with cement plastering 10 mm thick with cement mortar (1:4) on internal & exposed surfaces, including MS cover of size 01 mtr x 01 mtr made out from 3 mm thick MS sheet including (40 x 40 x 5) mm angle iron framing on MS cover as well as on top wall of the valve pit & painting of the steel surfaces with two coats of synthetic enamel paint (first quality) over a coat of red oxide primer, including necessary earth work and demolition of the existing old valve pit, complete all as specified and as directed.

All as per Item No 43 but here in before size90X90x90 CM

All as per Item No 43 but here in before size 60X60x60 CM

Taking down the defective electric induction motor of any capacity of Kirloskar make 415 Volt, 3 phase by disconnecting the electrical connections, removing the motor from bed, by decoupling with pump, transporting to workshop, desassembling rotor/ stator, bearing , oil seal etc and re-assembling the same after heating varnishing and , replacement unserviceable spares eg bearing, oil seal etc and transporting back to site and refixing with proper aligment with the pump along with electrical connections including testing and commissioning, complete all as specified and as directed by the Engineer-in-Charge. Note: 1. Rewinding if required will be measured and paid seperately under relevant items of Sch 'A'. 2. Bearings/oil seal/other spares will be measured and paid sepately under relevant items of Sch 'A'.

Dismantling and removing the burnt out winding from rotor/ stator and rewinding the rotor or stator with same type super enameled copper wire of same gauge and with necessary insulating material ,cotton tape etc .

Supply & fix in replacement terminal board for 15 HP capacity motors complete all as specified.

Supply & fix in replacement oil seal for induction motor 50 HP capacity

Supply & fix in replacement oil seal for induction motor 2-3 HP capacity

Supply & fix in replacement bearing for induction motor 50 HP capacity

Supply & fix in replacement bearing for induction motor 2-3 HP capacity

M&L for overhauling of centrifugal pump set of any capacity of make Kirloskar, by desassembling completely and replacing unserviceable ball bearing, shaft sleeve, gland, neck ring gland rope shield, unserviceable nut, bolt, washer etc. and reassembling the pump and fixing alignment to the original position and coupling with pump complete all as specified and as directed by the Engineer-in-Charge.

M&L for overhauling of Monoblock pump set set 3 HP capacity of make Kirloskar, by desassembling completely and replacing unserviceable ball bearing, shaft sleeve, gland, neck ring gland rope shield, unserviceable nut, bolt, washer etc. and reassembling the pump and fixing alignment to the original position and coupling with pump complete all as specified and as directed by the Engineer-in-Charge.

All as per item No.54 above but 5 HP capacity monoblock pump set.

All as per item No.54 above but 7.5 HP capacity monoblock pump set.

All as per item No.54 above but 10 HP capacity monoblock pump set.

All as per item No.54 above but 12.5 HP capacity monoblock pump set.

All as per item No.54 above but 15 HP capacity monoblock pump set.

S&F in replacement of Ball bearing for pump 50 HP Capacity of make – SKF / NBC/ TATA

S&F in replacement of Ball bearing for pump 15 HP Capacity of make – SKF / NBC/ TATA

S&F in replacement of Ball bearing for pump 12.5 HP Capacity of make – SKF / NBC/ TATA

S&F in replacement of Ball bearing for pump 10 HP Capacity of make – SKF / NBC/ TATA

S&F in replacement of Ball bearing for pump 7.5 HP Capacity of make – SKF / NBC/ TATA /Toyo

S&F in replacement of Ball bearing for pump 5 HP Capacity of make – SKF / NBC/ TATA /Toyo

S&F in replacement of, rubber flexible joy type coupling for 50 HP capacity motors/pumps complete all as specified and as directed by the Engineer-in-Charge. Make : As per Sample. Model :- KWC 228

S&F in replacement of, rubber gasket 3 to 6mm thick suitable for submersible/mono block pump sets & motors complete all as specified and as directed by the Engineer-in-Charge.

Supply only CI gland plate for centrifugal/mono block pumps 50 HP capacity.

M&L for painting to 2 to 15 HP capacity mono block/centrifugal pump and motor with two coats of synthetic enamel paint over one coat of red oxide primer including cleaning and degreasing the surface complete all as specified and as directed by the Engineer-in-Charge.

M&L for painting to 50 HP capacity mono block/centrifugal pump and motor with two coats of synthetic enamel paint over one coat of red oxide primer including cleaning and degreasing the surface complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing as in replacement Contactor Coil suitable for MNX 25. Make : L&T/ABB/Havells

Supply and fixing as in replacement Contactor Coil suitable for MNX 50. Make : L&T/ABB/Havells

Supply and fixing as in replacement Contactor MNX 25 complete all as specified and directed. Make : L&T/ABB/Havells

Supply and fixing as in replacement Contactor MNX 50 complete all as specified and directed. Make : L&T/ABB/Havells

Supply and fixing as in replacement Relay rating 45 to 75 sec. complete all as specified and directed. Make : L&T/ABB/Havells

Supply and fixing as in replacement Timer ST-100 rating 01 to 45 sec. complete all as specified and directed. Make : L&T/ABB/Havells

Supply and Fixing inreplacement single phase preventor (Minilec-VSP-2/3) for starter panels at differents locations completed all as specified and directed.

Disconnecting carefully old unserviceable Ammeter from panel board and S & F of new 96 mm size square / circular digital type ammeter of range 0-30 Ampere or 0-100 Ampere, size of letters 25 mm, with set of CTs of suitable rating, necessary connecting / fixing arrangement and testing complete all as specified and directed. Make AE or Equivalent

Disconnecting carefully old unserviceable Voltmeter from panel board and S & F of new 96 mm size square / circular digital type Voltmeter of range 0-500 Volt, size of letters 25 mm, Make – AE (ISI Marked), necessary connecting / fixing arrangement and testing complete all as specified and directed AE or Equivalent

Supply and fixing 3 core 4 Sqmm PVC flexible copper cable for suction sweeper pump suitable length complete all as specified and directed.

Supply only PVC insulated single core stranded copper conductor conforming to IS: 694 (1990) 1100 volts grade 16 Sqmm, complete all as specified and directed. Make : FINOLEX/HAVELLS/PLAZA/NICCO/L&T

M&L for overhauling of non clogging centrifugal Sewage pump set 5 HP capacity installed at sec -52 , by dismantling completely and replacing unserviceable ball bearing, shaft sleeve, gland, neck ring gland rope shield, unserviceable nut, bolt, washer etc. and reassembling the pump and fixing alignment to the original position and coupling with pump complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing in replacement PVC suction hose pipe round of required size 80-100 mm dia and lengt from sewage sump to sewage pumpset including arrangment of nipples flanges, Rubber gasket, reducers at suction end and nut bolt clamps, and PVC strainer/ footvalve at last end complete all as specified by Engr in Charge.

M&L for overhauling/servicing of Suction sweeper pump set 2-5 HP capacity at swimming pool sec -24 , by dismantling completely and replacing unserviceable ball bearing, shaft sleeve, gland, neck ring gland rope shield, unserviceable nut, bolt, washer etc. and reassembling the pump and fixing alignment to the original position and coupling with pump complete all as specified and as directed by the Engineer-in-Charge.

M & L in replacement Steel expansion joint for filteration plant with flexible rubber and steel flanges of size 150 mm coplete all as directed

Supply only Swimming pool chemical TCCA 90 in granules use of disinfecting agent in swimming pool to achieving crystal clear and clean water complete all as specified and as directed by the Engineer-in-Charge.

DHARAMRAJ BUILDERS & ENGINEERS

MK Enterprises

BLUE HILL ELECTRICAL AND ELECTRONICS

AARYANS GLOBAL INDIA