Repair / maint of ceiling fans, wall mounted fan, exhaust fan and geysers and certain E/M repairs to married accn at NDV, ODV, Manekshaw, Navy Park, Jal Vihar, living accn including guest room, E/M store complex and BSO yard under GE Haddo Sri Vijaya

Amount

Taking down carefully old unserviceable aluminum/ copper point wiring (light, fan, socket or power) complete, including fittings & fixtures such as switches, ceiling roses, lamp holders, pendants, regulators sockets, junction/terminal boxes etc; removing from site and making good disturbed surfaces of walls, floors etc., to match with existing surrounding surfaces complete all as specified and as directed.

Taking down existing unserviceable main switches/ distribution boards/Fuse Units of any description alongwith MCBs/MCCBs and making good disturbed surfaces to match with existing surrounding finishes complete all as specified and as directed.

Taking down carefully old unserviceable light fittings only and removing from site complete all as specified and as directed.

Taking down existing unserviceable sub main wiring of any description and making good disturbed surfaces to match with existing surrounding finishes complete all as specified and as directed.

M&L for Point wiring two single core 1.5 sqmm size PVC insulated, unsheathed FRLSH multistranded copper conductor cable and one single core 1.5 sqmm size green colour PVC insulated FRLSH multistranded copper conductor cable as earth continuity conductor, 1100 volt grade (with proper colour coding Red/Blue/yellow for phase, black for neutral and green for earth) complete drawn through and including PVC casing and caping not less than 25 mm width with all fittings, surface on wall/roof /floor including including sunk pressed steel terminal boxes flush mounting in the wall for mounting switches/switch socket combinations/ fan regulators etc., covered with suitable size of modular cover plates complete in making good the existing surface with existing colour coding as required at site complete all as specified for the following :- Note :- The unit rate quoted shall deemed to include the cost of following :-

ONE LIGHT/FAN point controlled by one, one way 5 Amps switch.

ONE 5A SOCKET OUTLET point controlled by one, one way 5 Amps switch on independent board.

ONE 5A SOCKET OUTLET point controlled by one, one way 5 Amps switch on same board.

ONE BELL point controlled by one, one way 5 Amps switch.

Description same as per item Sl No 5 above but point wiring with two single core 4.0 Sqmm size cables and one 4.0 sqmm green colour cable as earth continuity conductor for one 3 pin 15 Amps socket out let on independent board complete all as specified and directed.

M&L for Point wiring complete with 1.5 Sqmm (nominal area) single core, PVC insulated unsheathed, FRLSH cable, 1100 volts grade, multistranded copper conductor (with colour coding of Red/Blue/Yellow for phase and Black for neutral), drawn through and including rigid non metallic PVC conduit(concealed/ Surface) of suitable size (not less than 25mm dia) and accessories fixed on walls/ceilings etc., including provision of PVC insulated 1.5 Sqmm FRLSH cable with copper conductor green in colour for earth continuity and connected to common earth dolly and sunk in modular type pressed steel terminal boxes of suitable modules made out of 1.6mm thick MS sheet duly painted with two coats of anti-corrosive paint all over and modular cover plates with frames on top for suitable modules on top for housing switches, sockets etc., all as specified and as directed for the following:-

ONE LIGHT/FAN point controlled by one, one way 6 Amps modular switch.

Two light point controlled by one switch 5 Amps one way complete all as specified and directed.

ONE 6A SOCKET OUTLET point controlled by one, one way 6 Amps modular switch on independent board.

ONE 6A SOCKET OUTLET point controlled by one, one way 6 Amps modular switch on same board with other switches.

ONE 6A SOCKET OUTLET point controlled by one, one way 6 Amps switch on independent but below the switch board of light point with cable of 1.5Sqmm size.

ONE BELL point controlled by one, one way 6 Amps modular switch.

Description same as per item Srl No.7 above but point wiring with 4.0 sqmm PVC FRLSH insulated multistranded copper conductor suitable for one 3 pin 15 Amps socket out let and one run of 4.0 sqmm cable for earth in green colour on independent board complete all as specified and directed.

S & F for switch modular type, 6 Amps 1 module, 230 volts AC circuit complete all as specified and directed. Make-Roma (Anchor) / Havells (Crabtree) / Legrand

S & F for socket outlet modular type 1 way 6 Amps, 3 pin, 230 volts AC circuit complete all as specified and directed. Make-Roma (Anchor) / Havells (Crabtree) / Legrand

S & F for switch modular type, 16 Amps 1 module, 230 volts AC circuit complete all as specified and directed. Make-Roma (Anchor) / Havells (Crabtree) / Legrand

S & F Socket outlet 2 in 1 modular type, 3 pin, 6 and 16, universal complete all as specified and directed. Make-Roma (Anchor) / Havells (Crabtree) / Legrand

S & F modular bell push 5 Amps 1 modular 230v, 50Hz AC complete all as specified and directed. Make-Roma (Anchor) / Havells (Crabtree) / Legrand

S & F stepped type modular fan regulator, 2 modular type complete all as specified and directed. Make-Roma (Anchor) / Havells (Crabtree) / Legrand

S & F Switch piano, flush type, single pole one way 5 amps all as directed. Make: Anchor/Cona/Legrand

S & F Switch piano, flush type, single pole one way 15 amps all as directed. Make: Anchor/Cona/Legrand

S & F socket outlet 2 in 1, 3 pin 5 amp, flush type, universal all as directed. Make: Anchor/Cona/Legrand.

S&F Socket outlet 2 in 1, 3 pin, 5 and 15, flush type, universal all as directed. Make: Anchor/Cona/Legrand.

S & F bell push switch, flush type, single pole, 5 Amps, 240 volts AC all as directed. Make: Anchor/Cona/Legrand.

M&L for ceiling rose, three terminal, 65x20mm size, PVC/Polycarbonate, insulated body, 5A, 240 volts complete all as specified and as directed.

S&F in repairs switch socket combination box type 2 in 1, 5 pin, 5 Amps, flush type,universal complete all as specified and as directed. Make: Anchor/Cona/Legrand

S&F in repairs switch socket combination box type 2 in 1, 6 pin, 5 Amps & 15 Amps, flush type,universal complete all as specified and as directed. Make: Anchor/Cona/Legrand

S&F electric bell, ding dong type, AC, 230 volts complete all as specified and as directed.

S&F in repairs fan regulator, electronic socket two module step type 120W complete as specified. Make : Anchor/Cona/Legrand

S & F in replacement of capacitor 2.5mfd, 230 Volts for ceiling fans including taking out old unserviceable one complete all as specified and as directed. Make:- Capco/ Univarsal/ Tibcon/ Epcos

Taking down carefully ceiling fan of any sweep/ cap/ make from its existing position of any height/ loaction after disconnecting from electricity, dismantling blades, opening up for carrying out servicing/over hauling, examining for damaged worn out parts like shaft, ball bearings etc., and applying grease to bearings, assembling back, preparing painted surfaces by cleaning dust, grease etc., and by filling cavities with filler to receive spray paint using synthetic enamel paint of existing shade, fixing up blades and hanging back in position and providing and connecting up with 1.0 sqmm twin core twisted flexible copper conductor of suitable length from connector of fan to ceiling rose and testing complete all as specified and as directed. NOTE: Spare parts like ball bearings, shafts etc shall be replaced only if found damaged and certified by Engineer-in-charge. If spares are replaced, they shall be measured and paid separately as SUPPLY ONLY.

Description same as per item Sl No 26 above but, exhaust fan of any sweep/cap/type complete all as specified and directed.

Description same as per item Sl No 26 above but, wall mounted fan of cap 400 mm sweep complete all as specified and directed.

Taking down of unsv exhaust fan of cap 380 mm sweep of any make from its existing position and rewinding by super enamelled copper winding wire of suitable gauge and size with Garware insulating paper, insulating varnish and oven drying for requisite insulation values including necessary PVC sleeves lead wires and testing after assembling in position in exhaust fan complete all as specified and as directed.

Description all as per item No 29 above but exhaust fan of cap 300 mm sweep.

Description all as per item No 29 above but wall mounted fan of cap 400 mm sweep.

Suplly only ball bearing suitable for ceiling fan with bearing No. 6201/6202 complete all as specified and as directed.

Suplly only shaft suitable for ceiling fan 1200mm/1400mm sweep complete all as specified and as directed.

S & F exhaust fan blade set of 250/300/380mm sweep (steel body) complete all as specified and as directed.

S & F Air ventilation fan blade set of 200/250 mm sweep (PVC body) complete all as specified and as directed.

Suplly only wall mounted fan blade set of 400mm sweep complete all as specified and as directed.

M & L for repair/ replacement of exhaust fan supporting MS frame with legs suitable for exhaust fan of cap 300 mm sweep complete all as specified and directed.

S & F Fan motor not less than 1200 RPM, 230 volt, single phase for Air ventilation fan of cap 200/250 mm sweep (PVC Body) complete all as specified and as directed.

S & F Fan motor not less than 1400 RPM, 230 volt, single phase for Exhaust fan of cap 300-380 mm sweep (steel body) complete all as specified and as directed.

Taking down carefully ceiling fan of any make, size from its location, handed over to AGE E/M store yard without any damage

S & F BLDC 5 star rated ceiling fan metallic body ISI marked 1200 mm sweep, 220V AC, 50 Hz with all accessories alogwith providing and connecting up with 1.0 sqmm 3 core flexible copper conductor of suitable length from connector of fan to ceiling rose and testing complete all as specified and as directed by Engr In charge. Make: Usha , Model No TECHNIX or equivalent to CG/ Havells/ Orient

Taking down carefully electric geysers of any make, type and capacity after disconnecting of electrical and water connections, opening of bottom cover, checking of all parts and taking out copper tank, checking of its leakage and removing the dust, brazing the leakage and painting of geysers with two coats of synthetic enamel paint, replacement of wornt out spares and reassembling the geyser and re-fixing back in its original position complete all as specified and as directed. NOTE: Spares shall be measured and paid separately under relevant items as SUPPLY ONLY.

S & F high speed air ventilating fan 300 mm sweep single ph, 230 volt, steel body with louvers incl all fixing arrangement complete all as specified and directed. Make -CG/Havells/ Usha

S & F air ventilating fan 250 mm sweep single ph, 230 volt, PVC body with louvers incl all fixing arrangement complete all as specified and directed.Make -CG/Havells/ Usha

S & F air ventilating fan 200 mm sweep single ph, 230 volt, PVC body with louvers incl all fixing arrangement complete all as specified and directed. Make -CG/Havells/ Usha

Supply only heating element 1500 watts.

Supply only thermostat switch.

SUPPLY ONLY pressure release valve.

SUPPLY ONLY thermal cut out.

SUPPLY ONLY indicator lamp RED/GREEN colour.

SUPPLY ONLY PVC connection 15mm size with PTMT nuts of length 600mm. Make:- Prayag/ Polytuff

Supply & fix Modular Ac Box With 20A DP MCB "C' Type, Metal Enclosure & Unbreakable Heavy Duty With ISI Plug Top, 240 volts AC supply for air conditioner, flush mounting in the wall complete all as specified and directed. Make:- Anchor (Roma) model no 98492 or equivalent in Crabtree, Legrand.

M&L for Sub main wiring complete with four runs (3P+1N) of 10.0 Sqmm single core, PVC insulated unsheathed, FRLSH cable, 1100 volts grade, multistranded copper conductor (with colour coding of Red/Blue/Yellow for phase and Black for neutral) and one run of 10.0 Sqmm single core, PVC insulated unsheathed, FRLSH cable, 1100 volts grade, multistranded copper conductor as earth wire green in colour including lugs, drawn through and including 32 mm wide rigid non-metallic PVC casing and capping and its accessories (OR) 25 mm dia PVC conduit and conduit accessories fixed in concealed or on surface of wall/ceiling/roof/ floor complete all as specified and as directed.

Description same as per item Sl No 53.0 above but sub main wiring with four runs (3P+1N) of 4.0 Sqmm single core duly earthed with one run of single core cable of same size but green in colour as continuous earthing wire.

Description same as per item Sl No 53 above but sub main wiring with four runs (3P+1N) of 6.0 Sqmm single core duly earthed with one run of single core cable of same size but green in colour as continuous earthing wire. NOTE for item No 53 & 55: Four runs (3P+1N) of copper conductor, One run of copper conductor as earth wire and one run of PVC casing and capping / PVC conduit shall be measured as one unit length.

Description same as per item Sl No 53 above but sub main wiring with two runs (1P+1N) of 6.0 Sqmm single core duly earthed with one run of single core cable of same size but green in colour as continuous earthing wire.

Description same as per item Sl No 53 above but sub main wiring with two runs (1P+1N) of 4.0 Sqmm single core duly earthed with one run of single core cable of same size but green in colour as continuous earthing wire.

Description same as per item Sl No 53 above but sub main wiring with two runs (1P+1N) of 1.5 Sqmm single core duly earthed with one run of single core cable of same size but green in colour as continuous earthing wire. NOTE for Item No( 56 to 58): Two runs (1P+1N) of copper conductor, One run of 1.5 Sqmm copper conductor as earth wire and one run of PVC casing and capping / PVC conduit shall be measured as one unit length.

S & F in replacement of DB VTPN sheet metal enclosure double door IP 43 protection, door earth suitable for incoming upto MCCB 100 Amps/ 200 Amps & outgoing MCB TP / SP. Triple pole and neutral 415 V 4 Way with 200 Amp rated standard bus bar of suitable size plate and common neutral link all enclosed in standard steel sheet flush mounting type factory fabricated complete and making good to the distrubed surface /walls all as specified and directed.

Description all as above Item No 59.0 but 6 way.

S & F in replacement of Triple pole and neutral sheet steel powder coated Distribution board IP -43 protection with door earthing for MCBs fitted with 200 Amps rated bus bar , Neutral link ,Earth Bar and Din rail suitable for use on 415 V, 50 Hz supply double door TPN DB system 04 ways, and making good to the distrubed surface /walls complete all as specified and directed.

S & F in replacement of MCB DB, SPN, 12-way, double door, 240 Volts with 200 Amps rated bus bar, IP-43 protection, shrouded neutral bus bar, cement spill protector, concealed in wall and making good disturbed surfaces to match with surrounding surface complete all as specified and as directed.

Description same as per item Sl No 62 above but 8 way.

Description same as per item Sl No 62 above but 4 way.

S & F in replacement of MCCB, 4 pole, 125 Amps, 50Hz, 25KA rupturing capacity, 415 Volts adjustable type with thermal and magnetic release complete all as specified and as directed.

S & F in replacement of MCCB, 3 pole, 100 Amps, 50Hz, 25KA rupturing capacity, 415 Volts adjustable type with thermal and magnetic release complete all as specified and as directed.

S&F in replacement of MCB TPN 40-100 Amps (`C’ series) having current rating 10 KA complete all as specified and directed.

S & F in replacement of MCB, TP, "C" series, 230 volts, 25-63 Amps, 10 KA rupturing capacity complete all as specified and as directed.

S & F in replacement of MCB, SPN, "C" series, 230 volts, 32 Amps, 10 KA rupturing capacity complete all as specified and as directed.

S & F in replacement of MCB, SP, "C" series, 240 volts, 6 to 32 Amps, 10 KA rupturing capacity complete all as specified and as directed.

S & F in replacement of 15 watts surface mounted LED light fitting , white/yellow colour as reuired as site with slim high perfomanance surfaced mounted LED light fittings, round/square shape as required at site made from die-cast aluminium and CRCA covering, powder coated in white colour complete all as specified and directed.Make : Luker Cat No LNPSRR15 or equivalent in Havells/ CG/ Philips. NOTE: The rate quoted deemed to include for any alterations required to existing false ceiling as per site condition for fixing light fitting

S & F in replacement of of LED slim panel lighting fixture of 18 Watt recess mounted 220V , 50Hz with finished in premium white powder coating ,environmental friendly energy efficient fitting recess mounted round/square in shape (Warm white/ white colour as per requirement of site complete) of light as required at site) complete all as specified and directed. Make : Luker Cat Part No. LNPR18 or equivalent in CG/ Philips/ Havells.

Description all as item No 72 above but 15 watt recess mounted. Make : Luker Cat Part No. LNPR15 or equivalent in CG/ Philips/ Havells.

Description all as item No 72 above but 12 watt recess mounted. Make : Luker Cat Part No. LNPR12 or equivalent in CG/ Philips/ Havells.

Description all as item No 72 above but 9 watt recess mounted. Make : Luker Cat Part No. LNPR9 or equivalent in CG/ Philips/ Havells. NOTE for item No 71 to 75 : The rate quoted deemed to include for any alterations required to existing false ceiling as per site condition for fixing light fitting.

S & F in replacement and testing Tube light fittings LED 20 watts 4 feet including all accessories and fixing arrangements for fixing the light fitting complete all as specified and directed. Make : Luker Cat Part No. LT522 or equivalent in CG/ Philips/ Havells.

S & F in replacement and testing Tube light fittings LED 10 watts 2 feet including all accessories and fixing arrangements for fixing the light fitting complete all as specified and directed. Make : Luker Cat Part No. LT510P or equivalent in CG/ Philips/ Havells.

S & F in replacement of Decorative, wall mounting, champagne gold finish fixture with plastic body including 9 W LED lamp B22 base all as specified and directed. Make : Havells Model No. LHFOECE1TZ1O014 or equivalent in Philips/ Havells.

S & F in replacement of concealed cob/ spot LED light energy efficient of cap 4 watt (WH/WW/NW of colour) LED for low ceiling height applications round in shape, pressure die-cast aluminium housing, spring loaded clips for easy mounting complete all as directed. Make : CG/ Philips/ Havells.

Supply and fixing and testing Mirrior light fitting of cap 20 watt with all fixing arrangements all as specified and directed. Make-Havells cat no LHLDESAARANC020 or equivalent to Philips/ CG

S & F in replacement of and testing LED recessed mounted 595 mm x 595 mm luminarie with high transmitive diffuser of cap 40 watt, with longer life and less maintenance including all accessories and fixing arrangements for fixing the light fitting complete all as specified and directed. Make : Luker Model No. LKM 2240 of any colour(WH/NWH/WW) as required to CG/ Philips/ Havells. NOTE: The rate quoted deemed to include for any alterations required to existing false ceiling as per site condition for fixing light fitting

S & F Surface mounted general purpose square shaped luminaire with low height CRCA housing and high transmissivity diffuser of cap 40 watt of size 595 mm x595mm x 65 mm including all accessories and fixing arrangements for fixing the light fitting to any heighted indoor palces complete all as specified and directed. Make : Luker Model No. LKMSRS40 or equivalent in CG/ Philips/ Havells.

S & F in replacement of LED, AC Rope Strip light, 60 LED per metre, of any colour (WW/NW/CDL), including all fixing arrangment as per site requirement complete all as specified and as directed. Make : Havells model No. LHEHBQP5TN6F325 or equivalent in CG/ Philips/ Havells.

S & F in replacement of FUOCO track LED light 12 watt, (WH/WW/NW) on channel of suitable size of required length as directed.Make : CG/ Philips/ Havells.

Supply and fixing indoor hanging lighting fixture with E 27 holder type incl lamp all as specified and directed ny Engr In Charge. Make : CG/ Philips/ Havells.

Supplying, fixing and testing Gamma single, Anthracite finish premium aluminium LED light fittings 3 watts (one way), 3000K lumen : 230 lm dimension 79 x 77 x 36 mm including all accessories and fixing arrangements for fixing the light fitting complete all as specified and directed Make : Philip Model No. 582088 or equivalent in CG/ Havells.

Supplying, fixing and testing Gamma single, Anthracite finish premium aluminium LED light fittings 7 watts,IP-65, 3000K lumen : 650 lm dimension 130 x 50 x 37 mm, including all accessories and fixing arrangements for fixing the light fitting complete all as specified and directed Make : Philips, Model No : 800041 LUCENT 2-way or equivalent make of CG/Havells

S & F of LED Neon rope light of cap 9 watt/mtr, with diffused PVC cover,450 lm/mtr, 220-240 Volts, incl driver, of any colour (WW), including all fixing arrangment as per site requirement complete all as specified and as directed. Make: Havells model no LHEHCPP7TN6W375 or equivalent to Philips/ CG

S & F in replacement 30 watts LED building security light fittings, IP 65 luminaire, Pressure die cast aluminium housing powder coated graphite grey and toughened glass including necessary fixing arrangements as per site requirements all as specified and directed by Engr In Charge. Make : CG/ Philips/ Havells/ Luker

Taking down old corroded GI bracket of 25 mm dia and supply and fixing new GI brackets of GI pipe light grade of size 25 mm dia including nuts, bolts and washers for building secufity light all as specified and directed

M&L for earthing complete with GI earth plate electrode of size 600mmx600mmx6mm thick buried directly in ground (earth pit not less than 2.25m deep below the normal ground level) with top edge of the earth plate not less than 1.5m below normal ground level connected to 4mm dia GI earth wire as earth lead connected by means of bolts, nuts, washers and check nuts made out of galvanised iron or steel all as shown on electrical plate No. 3 of SSR Part-I connected to common earth dolly including testing on completion complete all as specified and directed. NOTES: 1) The unit rate shall also include for earth work in any type of soil, PCC (1:3:6) type C1 chamber, pre-cast RCC (1:2:4) type B-1 using 20mm graded stone aggregate cover 50mm thick reinforced with TMT bars 8mm dia @ 100mm c/c both ways, funnel with watering pipe 20mm dia medium grade, GI protection pipe light grade 40mm dia and wire mesh complete in addition to item No. 1(a) to (e) of preamble (notes) under sub-heading earthing, specified on Sl. Page Nos. 451 & 452 of SSR Part-II. 2) Earthing lead and GI protection pipe beyond 7.5m will be measured and paid separately.

Repair to LED light /PTLs of any model/make/rating in position including testing of serviceability of connected accessories, and wiring upto respective switch/control unit including and replacing unserviceable items such as drivers , holder and making light functional. Note: (i) All the spares such as drivers, holder, LED tubes etc including replacing will be will measured and paid separately. (ii) The representative of the contractor shall report to Engineer-in-charge/JE on daily basis to carry out repairs to light fitting and completion report to be submitted all as specified and as directed

S & F in replacement of PVC insulated FRLSH copper conductor cable of following sizes, 1100 Volts grade, Heavy Duty, served with inner sheathing (flexible) industrial cable complete all as specified.

4.0 sqmm single core

6.0 sqmm single core

1.5 sqmm single core

Removing and refixing the following during Addn/ Altn/ modification of existing structure:-

Light fixture/ switch socket outlet of any type and any capacity.

Ceiling Fan/ Exhaust Fan of any sweep.

Split Air Conditioner of any capacity.

S & F in replacement of only electronic drivers for 10 to 24 watt LED post top luminaire / LED light fittings operated at input AC voltage 85 to 265 Volts, 50Hz, output DC voltage 42 to 65 Volts, 300MA, P.F > 0.95 incl necessary fixing arrangment as per site requirement complete all as specified and as directed. Make :- Philips/ CG/ Havells/ Bajaj

S & F in replacement of 9 Watts holder type (E22) LED lamp (E22) 230 Volts, 50Hz complete all as specified and as directed. Make :- Philips/ CG/ Havells/ Bajaj

S & F in replacement of 7 Watts retrofit holder type (E27) LED lamp 230 Volts, 50Hz complete all as specified and as directed. Make :- Philips/ CG/ Havells/ Bajaj

M&L for Repair to point wiring for light/fan/socket by cutting, removing and replacing the burnt and unserviceable wire with new FRLS cable and conduits with copper conductor 1.5/2.5 Sqmm size, jointing with same size wires, replacing the saddles, refixing the loose/hanging conduits/casing capping properly all as directed. Note:(i) Rate is inclusive for FRLSH cable and other minor items (ii) The representative of the contractor shall report to Engineer-in-charge/JE on daily basis to carry out repairs and completion report to be submitted all as specified and as directed

M&L for taking down of unsv /damaged Casing & caping of size 25mm x12 mm from its existing location and s & f in replacement of the same alongwith connected accssories ,fixing with the wall, roof etc as specified and directed by Engr In Charge.

Supply and fixing with wall, piller, wooden structure etc. uPVC Panel Trunking of size 60 mm (H) x 50 mm (W) for running of wire, cable of any type etc complete all as specified and directed by Engr In charge. Make :- Precision or equivalent to Supreme .

Description all as per item No 100 above but Conduit 25 mm dia.

S & F in replacement of modular white cover plate with farme suitable for 3 module, refixing with the existing /new switches all as specified and directed by Engr In Charge.

Description all as per item no 102 above but suitable for 4 module.

Description all as per item no 102 above but suitable for 6 module.

Description all as per item no 102 above but suitable for 8 module. Note for item No 102 to 105 :- The new modular switch/sockets required will be measured and paid separately under relevant item.

ICON AGENCIES (BID ID -3349955)

A. R. ELECTRICALS (BID ID -3350246)

Sree Tirumala Enterprises (BID ID -3350445)

Tropical Refrigeration (BID ID -3350325)

Kathir Marketing Services (BID ID -3350403)