Development of Borimuri Fish Seed Farm, Lakhimpur

Amount

a) Earth Filling and Dismantling

Item 1/APWD(B) 1.4 :- Raising low site around the building with approved soil obtained from outside by truck carriage including breaking clods, dressing etc. complete including paying necessary land compensation, municipal gate fees, if any monopoly duty etc. (profile measurement to be taken and 12.5% deduction for shrinkage to be made from total quantityetc. complete as directed and specified, including forest royality within a distance of 8.00Km. (Forest royality shall be reimbrushed on production of necessary certificate from the forest authority duly countersigned by D.F.O. concerned).

Front Side of Hatchery

Back Side of Over Head Tank

Item 2/APWD(B) 23.15 :- Demolishing CC Floor of various thickness including top layer and base course and disposal of debris as directed for all levels

Circular Postplate Over Inside Wall of Hatching Pool

Post in Inner Circular of Hatching Pool

Breeding Pool Flooring

Hatching Pool & Egg Collection Chamber Flooring

Overhead Tank

Overhead Tank

b) Construction of Spawn Collection Tank

Item 3/APWD(B) 1.1.A.b :- Earthwork in Excavation for foundation trenches of wall, footing of column, steps, septic tank etc. Including refilling thequantity as necessary after competion of work, breaking clods in return filling, dresssing, watering and ramming etc and removal of surplus earth with all lead and lift as directed and specified in the following classiofication of soils including bailing out water where necessary as directed and specified.(A) Upto a depth of 2.00m below the existing ground level.(b) In hard/ dense soil (Earth Work for hatchery Column)

Excavation for foundation

Item 4/APWD(B) 4.1.1(a):- Providing soiling in foundation and under floor with stone / best quality picked jhama brick, sand packed and laid to level and in panel after preparing the sub grade as directed including all labour and materials and if necessary dewatering complete (a)Brick on flat soling ( soling in hatchery column)

Soiling under Foundation

Item 4/APWD(B) 18.1.1. b :- Supplying, fitting and fixing in position reinforcement bars conforming to relevant I.S. Code for R.C.C. work/ R.B. walling including straightening, cleaning, cutting and bending to proper shapes and length as per details, supplying and binding with 20G annealed black wire and placing in position with proper blocks, supports, chairs, spacers etc. complete (upto 1st floor level).

Bottom Mesh : Along X-X direction

Along Y-Y direction

Vertical Post: Main Bar

Stirrups

Protruding rod

Item 5/APWD(B) 3.1.1.1. b :- Providing form work of ordinary timber planking so as to give a rough finish including centering, shuttering, strutting and propping etc., height of propping and centering below supporting floor to ceiling not exceeding 4.0M and removal of the same for in-situ reinforced concrete and plain concrete work in: Foundation, footings, bases of columns, pile cap, raft and mass concrete works etc. Using 25mm thick plank.

Form work for Post

Item 6/APWD(B) 2.2.1.A.a :- Providing and laying plain/reinforced cement croncrete works cement with coarse sand & 20mm down graded stone aggregate including dewatering if necessary, and curing complete but excluding cost of form work and reinforcement for reinforced cement concrete work (form work and reinforcement will be measured and paid separately)

Floor

Item 7/APWD(B) 4.1.8(A)(a):- 112 mm thick 1st class brick nogged wall in cement mortar including racking out joints and curing complete as directed in super structure above plinth up to 1st floor level (protruding M.S rod/Tor steel of column to be embeded in cement mortar and will be measured and paid separately) In cement mortar in proportion 1:4.(1 cement:4 sand)

Wall along X-X direction

Wall along Y-Y direction

Item 8/APWD(B) 5.1.10.b :- Cement plaster skirting with cement mortar in prop 1:3 (1cement : 3 coarse sand) fimished with a floating of neat cement including of junctions with floor outside.

Floor

Outside wall

Outside wall

Inside wall

Inside wall

Top of the wall

Item 9/APWD(B) 13.4.7.a:- Wall painting (Two Coats) with plastic emulsion paint of Approved brand & manufacture (ASIAN / BERGER / ICI / NEROLAC etc.) on new surface to give an even shade after throughly brushing the surface free from morter dropings & other foraign matter & sand paper smooth.

Floor

Outside wall

Outside wall

Inside wall

Inside wall

Top of the wall

c) Breeding Pool (1 No.), Heatching Pool (3 Nos.) Renovation

Item 10/APWD(B) 2.2.1.A.a :- Providing and laying plain/reinforced cement croncrete works cement with coarse sand & 20mm down graded stone aggregate including dewatering if necessary, and curing complete but excluding cost of form work and reinforcement for reinforced cement concrete work (form work and reinforcement will be measured and paid separately)

Breeding Pool Flooring

Hatching Pool Flooring

Circular Postplate Over Inside Wall of Hatching Pool

Post in Inner Circular of Hatching Pool

Item 11/APWD(B) 13.4.7.a:- Wall painting (Two Coats) with plastic emulsion paint of Approved brand & manufacture (ASIAN / BERGER / ICI / NEROLAC etc.) on new surface to give an even shade after throughly brushing the surface free from morter dropings & other foraign matter & sand paper smooth.

Breeding Pool : Outside wall

Inside wall

Floor

Hatching Pool: Outside Wall

Inside wall

Top of outer wall

Floor

Inner post Side

Inner Circular post Plate

d) Overhead Tank Renovation

Item 12/APWD(B) 5.1.10.b :- Cement plaster skirting with cement mortar in prop 1:3 (1cement : 3 coarse sand) fimished with a floating of neat cement including of junctions with floor outside.

e) Cost of Pipes & Fittings, Purchase & Installation of 5 HP diesel driven pump, Purchase of Oxijen Cylender

Item 13/APWD(Sanitary)/3/1/1/I/a :- Supplying fitting & fixing GI Pipes of following sizes, with all necessary approved PVC fittings, such as bend, tee, elbow, reducer, nipple, plug, long screw fitting, H.W. clamps etc, complete at all levels including below G.L. as directed and rectified. (I) In exposed surfaces or in trenches.(a) 50mm dia (medium) (ii) Using otherISI marked approved brand

Supply & Shower line to BP and SCT- 1&2: Piping from overhead reservoir to BP for water Supply

Pump section & delivery pipe

Supply & Shower line to HP1 & HP-2 : Piping from overhead reservoir to HP-1 for duckmouth water supply and showering

(b) 40mm dia (medium) (ii) Using otherISI marked approved brand

Shower line to BP: branching from 50mm pipe to top of BP for Showering

Supply Line to BP: branching from 50mm pipe to top of BP forsupply water

Supply Line to HP 1 & 2: branching from 50mm pipe to top of HP for Showering

Supply Line to HP 1 & 2

(C ) 25mm dia (medium) (ii) Using otherISI marked approved brand

Shower line to HP -1 & 2: Around top of HP-1&2 for showering

Around top of SCT 1 & 2 for showering

Item 14/APWD(Sanitary)/3/17/4/a :- Supplying fitting & fixing G.I. foot valve with strainer including cutting necessary threads to pipes (a) 50mm dia (heavy type)

All pump suction pipe end under water

Item 15/APWD(Sanitary)/1.37.1. a. ii) :- Supplying fitting & fixing PVC pipes of 0kg/ (Supreme/Prince) or other ISI approved including joining, fitting and fixing with champs etc. as necessary complete at all levels including below GI as directed and specified (a) In exposed surface or in trenches

iii) 90mm dia: Spawn pipo from HP-1&2 to SCT -1&2

Spillway pipo from HP-1&2 at its contro

Item 16/APWD(Sanitary)/3/17/1/a :- Supplying fitting & fixing gun metal country pit valve (full way valve) ISI Make as specified and directed

(a) 50mm dia: Main line from OHT to BP

Main line from OHT to HP -1&2

Item 17/APWD(Sanitary)/3/17/1/b :- Supplying fitting & fixing gun metal country pit valve (full way valve) ISI Make as specified and directed

(b) 40mm dia: In Supply line to BP

In Shower line to BP

In supply (duckmouth) line to HP 1 & 2

In supply line to SCT 1&2

Item 18/APWD(Sanitary)/3/17/1/c :- Supplying fitting & fixing gun metal country pit valve (full way valve) ISI Make as specified and directed

(c) 25mm dia: In shower line to HP1 & 2

In shower line to SCT 1& 2

Item 22/APWD(Market) : Plastic shower

15mm (market)

Item 19/APWD(Market) :

Purchase of one 5 HP diesel driven pump (Usha/Kirloskar) machine

Item 20/APWD(Market) :

Purchase of 7.5cm dia helical pipe for suction and delivery

Item 21/APWD(Market) :

Purchase of oxygen cylinders B-type big/40cft 10.2 litres

f) Agronet (Biosecurity) for Nursery Tank ( Total 8 nos)

Item 22/APWD 1.1(A)(b) :Earthwork in Excavation for foundation trenches of wall, footing of column, steps, septic tank etc. Including refilling thequantity as necessary after competion of work, breaking clods in return filling, dresssing, watering and ramming etc and removal of surplus earth with all lead and lift as directed and specified in the following classiofication of soils including bailing out water where necessary as directed and specified.(A) Upto a depth of 2.00m below the existing ground level.(b) In hard/ dense soil (Earth Work for Nursery 1 Column)

Foundation

Item 23/APWD(B) 18.3.1. a :- Roof Truss providing fitting hoisting and fixing of roof trusses including purlins fabricated using MS circular hollow section conforming to relevant IS code as per approved design and drawing including providing MS cleats base plates bolts and nuts and one coat of red oxide zinc chromate primer and two coats of approved enamel paints complete including fitting necessary cleats etc for fixing ceiling joists as per design and drawing as directed (a) TATA make circular Hollow section CHS of Grade YST-310 conforming to I.S specification: 1161-1998

Vertical Bar

Horizontal Rafter

Horizontal Purlin

Item 23/APWD(B) 2.2.1.A.a :- Providing and laying plain/reinforced cement croncrete works cement with coarse sand & 20mm down graded stone aggregate including dewatering if necessary, and curing complete but excluding cost of form work and reinforcement for reinforced cement concrete work (form work and reinforcement will be measured and paid separately)

Post hole

Item 24/APWD(Market) :- Supplying fitting & fixing Agronet

Top portion

Side portion

Side portion

g) Renovation of Seed Conditioner Room

Item 25/APWD(B) 18.3.1. a :- Roof Truss providing fitting hoisting and fixing of roof trusses including purlins fabricated using MS circular hollow section conforming to relevant IS code as per approved design and drawing including providing MS cleats base plates bolts and nuts and one coat of red oxide zinc chromate primer and two coats of approved enamel paints complete including fitting necessary cleats etc for fixing ceiling joists as per design and drawing as directed (a) TATA make circular Hollow section CHS of Grade YST-310 conforming to I.S specification: 1161-1998

Tie Member

Rafter

Suporting Member

Purlin

Item 26/APWD(B) 8.1.33. v. :- Providing Pre Painted Galvanized Iron Sheet Roofing (PPGI) (Dyna roof / Sathyam/ Durakolor/ Century Wells) at all levels including fitting and fixing with self drilling, self tapping screws complete. (Roof trusses, purlins etc. to bemeasured and paid separately.) 0.60 mm thick

Roof Area

Item 27/APWD(B) 8.1.26.b :- Providing Pre Painted Galvanized Iron Sheet Ridging (PPGI) (Dyna roof / Sathyam/ Durakolor/ Century Wells) at all levels including fitting and fixing with self drilling, self tapping screws complete. (Roof trusses, purlins etc. to bemeasured and paid separately.) 0.60 mm thick

Ridging

h) Chain Link Fenching : Item 28/APWD(B)17.10 :- Supply, fitting and fixing chain link fenching of 10 S.W.G.G.I. wire 50mm fitting, and fixing hooks ,eye bolts with nuts , staples and bolts including three horizontal lines of G.I. wire 10 swg at top ,middle and bottomn with one vertical line to each fenching post for keeping the fenching tight and erect complete, including one coat of primer painting MS angle iron post in PCC base etc with following. a) Corner and end post with MS angle of size 50mmx50mmx5mm b) Ength not less than 1800 mm only duly slotted and bottom torque and splayed.

Fenching Area

Item 29/APWD(B) 2.2.1.A.a :- Providing and laying plain/reinforced cement croncrete works cement with coarse sand & 20mm down graded stone aggregate including dewatering if necessary, and curing complete but excluding cost of form work and reinforcement for reinforced cement concrete work (form work and reinforcement will be measured and paid separately)

Post hole

i) Aproach Road: Item 30/APWD(B) 4.1.1(a):- Providing soiling in foundation and under floor with stone / best quality picked jhama brick, sand packed and laid to level and in panel after preparing the sub grade as directed including all labour and materials and if necessary dewatering complete (a)Brick on flat soling

Soling under Approach Road

Item 31/APWD(B) 5.1.4 - 40 mm thick cement concrete floor consisting of 25mm under l;ayer of cement concrete in prop. 1:3:6(1 cement:3 coarsesand: 6 coarse aggregate of 25mm and down) and 15 mm thick wearing layer in cement concrete in prop 1:1:2 (of size 10mm down) laid in panels and finished with a floting coat of neat cemant finish ( using cement slurry for bond @ 2.75 kg per sq meter of floor area) including curing etc complete as directed

Approach Road Flooring

j) Shed Over Hatchery: Item 32/APWD 1.1(A)(b) :Earthwork in Excavation for foundation trenches of wall, footing of column, steps, septic tank etc. Including refilling thequantity as necessary after competion of work, breaking clods in return filling, dresssing, watering and ramming etc and removal of surplus earth with all lead and lift as directed and specified in the following classiofication of soils including bailing out water where necessary as directed and specified.(A) Upto a depth of 2.00m below the existing ground level.(b) In hard/ dense soil (Earth Work for Nursery 1 Column)

Excavation for foundation

Item 33/APWD(B) 2.2.1.A.a :- Providing and laying plain/reinforced cement croncrete works cement with coarse sand & 20mm down graded stone aggregate including dewatering if necessary, and curing complete but excluding cost of form work and reinforcement for reinforced cement concrete work (form work and reinforcement will be measured and paid separately)

Post hole

Item 34/APWD(B) 18.3.1. a :- Roof Truss providing fitting hoisting and fixing of roof trusses including purlins fabricated using MS circular hollow section conforming to relevant IS code as per approved design and drawing including providing MS cleats base plates bolts and nuts and one coat of red oxide zinc chromate primer and two coats of approved enamel paints complete including fitting necessary cleats etc for fixing ceiling joists as per design and drawing as directed (a) TATA make circular Hollow section CHS of Grade YST-310 conforming to I.S specification: 1161-1998

Vertical Post

Rafter 1

Rafter 2

Purlin 1

Purlin 2

Item 35/APWD(B) 8.1.33. v. :- Providing Pre Painted Galvanized Iron Sheet Roofing (PPGI) (Dyna roof / Sathyam/ Durakolor/ Century Wells) at all levels including fitting and fixing with self drilling, self tapping screws complete. (Roof trusses, purlins etc. to bemeasured and paid separately.) 0.60 mm thick

Roof Area 1

Roof Area 2

k) Deep Tube Well: Item 36/APWD(B) 5.3.2 :- Labour for test boring with 40mm (internal) dia G.I. pipes including keeping surplus of earth and every 2m after first 3.00m depth and delivering the same in nearest PWD camp in the samll tin container (container scaffolding tools etc. will have to be arranged by the contractor at his own cost).

Test Boring

Item 37/APWD(snws) 5.3.4 :- Labour for boring hole for inserting tube well pipes through different soil/rock media including hire charges of drill pipes, scaffolding, tools and plants as necessary and taking out the same and lowering pipes,fittings complete as directed by the department. ii) Bore hole of 100mm diameter

Boring Hole

Item 38/APWD(B) 5.3.5:- Supplying, fitting and fixing pipes plain/bevel ended for casing, conforming to relevant IS codes of practice including supplying and fitting of tube well accessories, lowering of assembly pipes concentrically in the borehole followed by supplying and paking of pea gravel free from dirt, dust and other forien materials in the annular space between the borehole and assembly pipes complete as directed by the Department. G.I. pipe (a) TATA/SAIL (mediam) iii) 100mm diameter

GI Pipe 100 mm Diameter

Item 39/APWD(B) 5.3.6:- Supplying, fitting and fixing suction pipes plain/bevel ended , conforming to relevant IS codes of practice including supplying and fitting of accessories, lowering of assembly pipes concentrically in the casing pipes complete as directed . G.I. pipe (a) TATA/SAIL (mediam) iii) 40mm diameter

GI Pipe 40 mm Diameter

Item 40/APWD(B) 5.3.10:-Supply fitting and fixing ribbed screen PVC filter 3.00 meter long (d) 100mm diameter

Filter pipe

Item 41/APWD(B) 5.3.12:- Development of the tubewell with compressor or by over pumping unit for 48 hours till sand free discharge is obtained.

Development of Tube Well

Item 42/APWD(B) 39.7:- Supplying including installation of submersible type water supply motor pumpset with all accessories including panel board on CC foundation of proportion 1:2:4 jammed with MS Nuts and bolts wire rope submersible cable without suction G I Pipe including making necessary connection etc. as reqd. copmlete. Stage 5 to 18 with MCB controlled submersible motor pumpset.

Submersible motor pump set

SYED ABUL HASSAN

MS D.P ENTERPRISE