ADDN/ALTN TO EXISTINING ALUMINIUM WIRING IN CERTAIN MD ACCN AT AIRFORCE CAMP BALLYGUNGE

Amount

Taking down chowkhats or frames with shutters (without taking off shutter from frames) of any sizes nexc 1.5 Sqm complete all as specified and directed.

Taking down cement plaster of any description on brick work or stone msonary wall including racking ot joints hacking for key scrubbing down with water etc. complete all as specified and directed.

Surface dressing not exc. 150mm deep and getting out in Soft/Loose Soil, complete all as specified and as directed.

Surface Excavation exc. 45 Cm but nexc 60cm deep and ave. 45 Cm deep and getting out in Soft/Loose Soil, complete all as specified and as directed.

Excavating in trenches, n exc 1.50 m wide and n exc 1.50 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sqm on plan and n exc 1.5 m in depth and getting out in soft and loose soil complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 Cm as in soft/loose soil complete all as specified and directed.

Removing excavated material ( soils of any type) not exc. 50 m and depositing where directed at a level not exc 1.5 m above the starting point complete all as specified and directed.

M&L Hardcore (broken stone or boulders) of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L Treating the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface (Area of the sub structure in contact with backfill to be measured) complete all as specified and directed.

M&L Treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface complete all as specified and directed.

M&L Treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area complete all as specified and directed.

M&L Treating the soil along with external perimeter of building at the rate of 2.25 litre of emulsion per metre of the perimeter wall complete all as specified and directed.

M&L for Cement concrete type 1:3:6 type C-2 (Using 40mm graded crushed stone aggregate) as in foundations, filling and mass concrete complete all as specified and directed.

M&L Reinforced Cement Concrete (Design Mix) M-25 in Roof Beams, Cantilevers, Bres-summers, Lintels over 1.50 Metre Span, complete all as specified and as directed. NOTE : Formwork and Reinforcement shall be Measured and Paid for separately under relevant Items.

M&L Reinforced Cement Concrete (Design Mix) M-25 in Chajja, etc., complete all as specified and as directed. NOTE : Formwork and Reinforcement shall be Measured and Paid for separately under relevant Items.

M&L Plain Cement Concrete type C-1, (1:3:6) (40mm graded crushed stone aggregate) as in Coping bed plate,hold fast etc,block benching,channeling slightly rounded or chamfered angle and throating including form work and finishing all exposed faces of cement concrete complete all as specified and as directed.

Cutting chase, pinning in making good to facing where required and pointing in CM 1:3 to end or edges of landing steps, cills, sunshades, shelves, lintels etc. and cutting chase for concealed water pipe etc. and making good cutting not exc 10Cm girth.

M&L fly ash bricks pulverizes using class 'A 'old size bricks straigth or curved on plan exc 6m mean radius built in CM (1:6) cmplete all as specified and directed.

M&L Formwork to Sides and Soffits of Floor or Roof Beams, Beam Haunchings, Girders, Bres-Summers, Lintels, Cantilevers, Shelves including supports, overhangs, etc. also splays between floors and beams, etc., flat, rough finished surfaces of concrete, complete all as specified and as directed.

M&L Formwork to Chajjas and chulla Similar Items including edges, flat, rough finished surfaces of concrete, complete all as specified and as directed.

Providing and fixing factory made uPVC white colour sliding window (Area of each window not exceeding 2.00 sqm) Three track made of extrueded profiles with wall thickness of 2.3mm (+-0.2mm). Window profile with hollow section with multi chamber. Frame (88mm x 52 mm), sliding sash (42mm x 67mm). Sliding mesh sash (42mmx57mm) Sliding interlock (one vertical length in each shutters) (45.5mmx28mm), Glazing bead (24.5mmx16mm) will be mitered cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gastket, 1.2 (+-0.2mm) thick galvanised steel fr Frame (30mmx18mm) 2 Nos, sliding sash (30mmx18mm) , sliding mesh sash (36mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mmx 100mm long fasteners, hardware (Touch Lock of Zinc alloyed (white powder coated), steel roller system. Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperature 1.40 mm and required accessoreis (Note:- The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Net Opening will be measured for payment purpose.)

Supply and fixing factory made UPVC door frame made of UPVC extrude sections having an overall dimension (extrude section profile) 48x40mm (tolerance +-1mm) with wall thickness 2.00 mm (+-0.2mm) corners of the door frame jointed with galvanized brackets and stainless steel screws, joints, miterd and plastic welded. the hinge side vertical of the frames reinforced by galvanized MS Tube of size 19x19mm and 1mm (+-0.1mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame completed all as specified by the manufacturer and as per directions of Engr in charge.

Supply and fixing factory made UPVC white colour Casement door with 3D Hinges made of (big series) frame 67x64mm & sasg 67x 110 mm both having wall thickness of 2.3 +-0.2mm and glazing bead/double glazing bead of appropriate dimension. Comprising of UPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 +-0.2mm thick galvanized mild steel section made from roll forming process of required length (shape and size according to UPVC profile), UPVC extruded glazing beads of appropriate dimensions, EPDM gasket, zinc alloy (white powder coated) 3 D hinges and one handle on each side of panels alongwith zinc plated mild steel multi point locking having transmission gear, cylinder with keeps and one side key, GI fastners 100x8mm size for fixing frame to finished wall and neccessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners mullion(if required) shall be also fusion welded including drilling of holes for fixing hardwares and drainage of water etc. after fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and approved quality complete all as specified and directed by Engr in charge (glass shall be paid separately)

S&F Mortice lock, Brass, 4 Levers, vertical type, size 75 mm and fixed, complete all as specified and as directed.

S&F Double action floor spring hydraulically regulated, made up of minimum 1.25mm thick aluminiun alloy sheet foundation box, main body with stainless steel cover ,governing piovet made of brass ,other parts made of mild steel heavy duty and fixed complete all as specified and as directed. Make -Godrej Cat no - 4102 or equivalent.

M&L Mild steel TMT bars 10mm dia and over, cut to length bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality conforming to fe 410-S.complete all as specified and as directed.

M&L TMT Bars 8 mm dia , cut to length, bent to shape required including crank-ing, bending and binding with and including Mild Steel Wire (annealed) not less than 0.90 mm, complete all as specified and as directed.

M&L TMT Bars 8 mm dia , cut to length, bent to shape required including crank-ing, bending and binding with and including Mild Steel Wire (annealed) not less than 0.90 mm, as in stirrups spacers and binders complete all as specified and as directed.

S&F for Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed.

M&L Steel Work in Tubular Post/Trusses hollow section including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS-4923 grade YSt.-240 complete all as specified and as directed.

S&F Plates (Plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment conforming toFe-410-W (Gde-E- 250 quality -B) complete all as speci-fied and as directed.

M&L Mild Steel Screw Bolts (machine made) 16mm to 20mm diameter of neck and length of bolt exc 15 Cm and not exc. 22.5 Cm with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, complete all as specified and as directed.

Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS:733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top,bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle,Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge.

S&F Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing powder coated aluminium handle, tower bolt, door stopper as required including the cost of EPDM rubber/neoprene gasket required with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws complete all as specified and directed of Engineer-in-charge

Supply and fixing of 5mm thick ACP (Aluminium Composite Panel) exc 0.5 sqm in each pane complete all as specified and as directed

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated/semi corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screw complete all as specified and directed.

M&L False ceiling with 'E' board "Classic" , reinforced, designer series, board with HPSC of size 600 mm x 600 mm x 4 mm thick fixed on aluminium powder coated snap grid to support the boards/files with aluminium anodised main 'T' section 35mm x 23mm x 1.50mm cross tee 35mm x 23mm x 1.50mm thick and aluminium angle 25mm x 25mm x 1.40mm as on edges/sides duly suspended with 4mm dia GI hanger fixed with GI hooks 4mm dia and fastner as required at the site and applying two coats of oil bound distemper over a coat of alkali resistant primer on exposed surfaces complete all as specified and as directed.

M&L for 150mm thick plain cement concrete type C-2 (1:3:6) (Using 40 mm graded crushed stone aggregate) as in sub base complete all as specified and directed.

M&L Cement Concrete type D2 (1:4:8) using 40mm graded aggregate 75mm thick in Sub-bases, finishing concrete surfaces fair and even, complete all as specified and as directed.

M&L 75mm thick PCC (1:3:6) type C-2 (Using 40mm graded stone aggregate) as in plinth protection laid in panels, finish the top surfaces even and smooth without using extra cement complete all as specified and directed Note:- Construction joints will be provided at interval of 2.5m length and filled with bitumen 80/20 mix with sand in ratio of 1:3 and cost of the same shall be deemed included in quoted rate

M&L 25mm thick PCC (1:2:4) type B-0 (using 12.50mm graded stone aggregate) as in sub base of floor complete all as specified.

Providing and laying 80mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour,design & pattern as in footparth, parks,lawns, drive ways or light traffic parking etc.,of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, complete all as spcified and directed.

M&L Double charge Vitrified Ceramic Tiles 10 mm thick (square/ rectangular) in light Shade, Polished, area of each tile not exc 0.36 sqm as in Floors, etc. Set and Jointed in Neat Cement Slurry and Pointed in White or Coloured Cement to match the Shade of the Tiles over 20mm thick screed bed in cement sand mortar (1:6) complete all as specified and as directed.

M&L Double Charge Vitrified Ceramic Tiles 10 mm thick (square/ rectangular) in Light Shade, Polished, Area of Each Tile nexc. 0.36 Sqm as in vertical surface such as Skirting, Dados, Risers to Steps etc. Set and Jointed in Neat Cement Slurry and Pointed in White or Coloured Cement to match the Shade of the Tiles, complete over 15 mm thick backing layer cement mortar (1:4) complete all as specified and as directed.

M&L rendering 15mm thick in CM (1:6) on other than fair faces of brick work or concrete surfaces even & smoth without using extra cement complete all as specified and directed.

M&L Rendering 15mm thick in Cement Mortar (1:4) on fair faces of brick work or concrete surface of wall using water proofing compound and finishing the surface even and smooth without using extra cement complete all as specified and as directed. (NOTE:-WPC shall be measured and paid separately)

M&L rendering 5mm thick in CM (1:3) as in ceiling surfaces even & smoth without using extra cement complete all as specified and directed.

"Supply only" liquid water proofing compound (ISI marked) complete all as specified and directed.

M&L Preparing new Surfaces of Walls and applying Two Coats of Distemper Oil Emulsion over a coat of primer and applied over 2mm thick BIRLA/JK water proof wall care putty including rubbing with emmery paper to make wall surface smooth and even complete all as specified and directed.

M&L preparing newly plastered surfaces and Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) complete all as specified & directed.

M&L Preparing new Steel or Iron Surfaces of any description, over 10 Cm width or girth and applying Two Coats of Synthetic Enamel Paint (First quality) over a coat of Red Oxide/ Zinc Chrome Primer, complete all as specified and as directed.

S&F Tinted glass with sheet glass 4.80mm thick , pin head type and glazing in squares exc 0.5 sq. M in each pane complete all as specified and as directed.

Taking down point wiring (light, fan, socket and power complete including fixtures and fittings such as switches ceiling roses, pendents , regulators, sockets, light fittings etc. removing materials to store for keeping in safe custody for refixing or for taking credit (credit for above items should be made as per conditions separately) and making good distrubed surfaces of walls, floors, etc.complete all as directed by Engineer-in-Charge.

M&L for Point wiring with PVC insulated and unsheathed FRLSH cable single core multistranded copper conductor 1.5 sqmm size, 1100 volts grade cable conforming to IS - 694 1990 drawn through and including PVC concealed conduit 20mm dia medium duty with all accessories including fabricated 1.6 mm thick MS terminal boxes fixed flush with wall surface with 3 mm thick plastic masonite laminated sheet top cover fixed with cadmium screw for mounting switches, sockets, regulator etc including 1.5 sq mm FRLSH stranded PVC insulated and unsheathed copper conductor earth continuity conductor to common earth and connecting to earth dolly all as specified for one light or fan point controlled by one switch single pole one way for light/ ceiling fan/ exhaust fan/call bell point/ Switch socket outlet 5 amps complete all as specified and as directed. Note: (i) Red coloured cable shall be used for live connection, black coloured cable shall be used for neutral connection and green coloured cable shall be used for earthing. Separate cable for earthing and neutral to be used for each individual circuit from the distribution board. (ii) Cutting Chases pinning shall be measured and paid separately under relevant item of Sch A

All as per item No 54.00 here-in-before but one 3 pin 5 amps socket outlet on the same board with other switch complete all as specified and directed by Engineer-in-charge.

All as per item No. 54.00 here-in-before but one 3 pin 5 amps switch socket outlet on the independent board with other switch complete all as specified and directed by Engineer-in-charge.

M&L Point wiring with 2.5 sqmm (Nominal Area) PVC insulated stranded single core unsheathed FRLSH copper conductor cable 1100 Volts grade drawn through with and including PVC concealed conduit 20mm dia medium duty with all fittings and accessories of casing caping (like Tee, Bend etc) complete fixed to walls / ceiling etc with and including 2.5 Sqmm (nominal area) PVC insulated unsheathed, stranded, single core FRLSH copper cable as earth continuity wire connecting to common earth point (including supply & fixing of 1.6 mm thick pressed mild steel terminal boxes of suitable size with 3 mm thick PVC /plastic laminated sheet, top cover suitable sizes of brass screws and washers etc. for mounting sockets for 5 pin, 16 Amp socket outlet on independent board complete all as specified and directed. Note: (i) Red coloured cable shall be used for live connection, black coloured cable shall be used for neutral connection and green coloured cable shall be used for earthing. Separate cable for earthing and neutral to be used for each individual circuit from the distribution board. (ii) Cutting Chases pinning shall be measured and paid separately under relevant item of sch A

M&L fo Point wiring surface type with 4.0 sqmm (Nominal Area) PVC insulated stranded single core unsheathed FRLSH copper conductor cable 1100 Volts grade drawn through with and including PVC concealed conduit with all fittings and accessories (like Tee, Bend etc) complete fixed to walls / ceiling etc with and including 4.0 Sqmm (nominal area) PVC insulated unsheathed, stranded, single core FRLSH copper cable as earth continuity wire connecting to common earth point (including supply & fixing of 1.6 mm thick pressed mild steel terminal boxes of suitable size with 3 mm thick PVC /plastic laminated sheet, top cover suitable sizes of brass screws and washers etc. for mounting sockets for 5 pin, 16 Amp Switch socket combination on independent board complete all as specified and directed. Note: Red coloured cable shall be used for live connection, black coloured cable shall be used for neutral connection and green coloured cable shall be used for earthing. Separate cable for earthing and neutral to be used for each individual circuit from the distribution board..

S&F Modular type switch 6 Amps 230V AC single module one way 1 module complete all as specified and as directed.

S&F Modular type switch 15 Amps 230V AC single module one way 1 module complete all as specified and as directed.

S&F Modular socket out let 3 pin 5 Amps flush type 2 module same board complete all as specified and as directed.

S&F Modular socket out let 3 pin 5 Amps flush type 2 module independent board complete all as specified and as directed.

S&F Modular socket outlet multipurpose 3 pin 15 Amps and one pin 5 Amps controlled by one switch complete all as specified and as directed.

S&F Modular electronic step type fan regulator by step type 230 volt.120watt,2 module complete all as specified and as directed.

S&F Modular bell push, 6/10 Amps 230V AC single module complete all as specified and as directed. Make:- Anchor Cat Part No. 21044 / Legrand-574824 / Havells-AHCSBXW100

S&F Modular cover plate with frame for fixing of modular switches/sockets complete for 1 modules complete all as specified and as directed. Make:- Anchor Cat part No.30216WH / CONA - 10801/Legrand- 675601

S&F Modular cover plate with frame for fixing of modular switches/sockets complete for 2 modules complete all as specified and as directed. Make:- Anchor Cat part No.30227WH /CONA - 10702/Legrand- WH 675562

S&F Modular cover plate with frame for fixing of modular switches/sockets complete for 3 modules complete all as specified and as directed. Make:- Anchor Cat part No.30228WH or equivalent model from make:- Legrand -WH 675563 / CONA - 30250.

S&F Modular cover plate with frame for fixing of modular switches/sockets complete for 6 modules complete all as specified and as directed. Make:- Anchor Cat part No.30250WH/ CONA - 10506/Legrand- WH 675566

S&F Modular cover plate with frame for fixing of modular switches/sockets complete for 8 modules complete all as specified and as directed. Make:- Anchor Cat part No.30260WH/ Legrand-WH 675567 / Cona- 10321

S&F Modular cover plate with frame for fixing of modular switches/sockets complete for 12 modules complete all as specified and as directed. Make:- Anchor Cat part No.30271WH / Legrand- WH 675572 / CONA- 10812

S&F Sunken flush metal GI boxes for fixing of modular switches/sockets flush to the walls. 1 Module/ 2 Module complete complete all as specified and as directed. Make:- Anchor Cat Part No. 35796 / Legrand-689007 / Havells-AHBXMIIX01.

S&F Sunken flush metal GI boxes for fixing of modular switches/sockets flush to the walls 3 Module complete complete all as specified and as directed. Make:- Anchor Cat Part No. 21452 / Legrand-689010 / Havells-AHBXMIZX03

S&F Sunken flush metal GI boxes for fixing of modular switches/sockets flush to the walls 6 Module complete all as specified and as directed. Make:- Anchor Cat Part No. 21463 / Legrand-6890106 / Havells-AHBXMIIX06

S&F Sunken flush metal GI boxes for fixing of modular switches/sockets flush to the walls12 Module complete all as specified and as directed. Make:- Anchor Cat Part No. 21485 / Legrand-689011 / Havells-AHBXMIIX12

S&F Ceiling rose surface bakelite three terminals 240 volts complete all as specified and as directed.

S&F Lamp holder suitable for batten fittings complete all as specified and directed by the Engr-in-Charge.

S&F Call bell, ding dong AC 230 volts, single pole complete all as specified and as directed. Make:- Anchor code 38921/Havells cat no-AHNWEMW000/Legrand cat no-673034/ Plaza / Cona.

S&F Ceiling fans complete with blades, down rods, electronic regulator and acessories 230 V 1200 mm sweep Min air delivery 210 CFM with service Value 6.00 BEE 5 Star rated with brushless direct current motor (BLDC) complete all as directed and specifed. Make:- Havells/CG/Philips/Orient or equivalent Note: Taking down old fan and depositing to MES store

S&F Wall fans complete with blades, 230 V ,RPM 1350,sweep 400mm Air Delivery (CMM) 85 complete all as directed and specifed. Note: Taking down old fan and depositing to MES store

Supply and fixing 1x1 ceiling light with superior efficacy thin and light weight back lit design lay into drop ceiling with system eficacay>90lmw CRI 80+IP 20 complete all as directed by engr in charge Make Magik Cat No PCHP024W

Supply and fix spot light 9 watt tunable 3000 to 6500K CRI> 90, 30 degree beam angle complete with all connection as directed. Make Magik Cate No CTEV009T3000TMW or equivalent in philips Surya Jaguar

S&F LED lamps of 10 watts lumen output 950lm ,colour temp 6500K ,base of B22 including taking down old unserviceable one complete all as specified and as directed. Make:- Havell's Cat No-LHLDDDAIA5R010 or equivalent Philips/ / Surya Roshni Ltd/ Bajaj/ Wipro/ C&S Electric Ltd.

S&F Energy efficient LED fittings of capacity 10 W suspended type / wall mounted type complete with LED tube Lamp and fitting with copper flexible PVC cable of 0.50 sq mm twin core not more than one metre in length including taking down old unserviceable one complete all as specified and as directed. Make:- Crompton cat no CIS.103-10.3-SL or equivalent in Havells Cat No-ENDURALINEARNEOBS10WLED830SPCWH/ Bajaj cat no-BCLSB 10 WH

S&F Energy efficient LED fittings of capacity 20W suspended type / wall mounted type complete with LED tube Lamp and fitting with copper flexible PVC cable of 0.50 sq mm twin core not more than one metre in length including taking down old unserviceable one complete all as specified and as directed. Make:- Crompton cat no CIS-305-40-57SL or equivalent in Havells Cat No-ENDURALINEARNEOBS20WLED865SPCWH/ Bajaj cat no-BRTX20W LED

S&F LED fittings with lamps of 30 watts for bldg security light IP 66 power Coated pressure die cast aluminium compact high power LED street light with compact size & rough design 32 mm GI Bend including taking down old unserviceable one complete all as specified and as directed. Make :- Crompton Cat No LSTS-35-CDL-M /Bajaj cat no-BCLST 35W LED/Havells Cat No-ENDURACITYLITEPLATPLUSSL35WLED757SASYBOPC.

Taking down unserviceable rusted / damaged MCB DBs of any type and way along with any type MCB and keeping serviceable MCB in safe custody in re-use in the work and making good to the distubed surfaces of walls etc. complete all as specified and as directed.

S&F MCB SPN DB made up with sheet metal single door, phosphorised, power coated, neutral link, earth bar and din rail, 4 way with 200 amps rated bus bar, 240 volts complete all as specified and as directed. Note- Found Unserviceable MCBs will be contractor property and will be measured under Schedule of Credit.

S&F Sheet metal enclosure doubleDoor for DB's where MCBs to be used 8 way single pole and neutral with 200 amps rated bus bar complete all as specified and as directed. Note- Found Unserviceable MCBs will be contractor property and will be measured under Schedule of Credit.

S&F Sheet metal double door enclosure for DB's when MCBs to be used 12 way single pole and neutral double door with 200 amps rated bus bar complete including connection complete all as specified and as directed. Make:- L&T Cat part No.-DBSPN012DD/Legrand cat no- 507602or equivalent ABB/ C&S Electric Ltd.

S&F MCB TPN DB made up with sheet metal double door, phosphorised, power coated, neutral link, earth bar and din rail, 4 way TPN with 200 amps rated bus bar,415 volts complete all as specified and as directed. Make:- L&T Cat part No.-DBTPE004DD/Legrand cat no- 507660 or equivalent ABB/ C&S Electric Ltd.

S&F MCB TPN DB made up with sheet metal double door, phosphorised, power coated, neutral link, earth bar and din rail, 8 way TPN with 200 amps rated bus bar, 415 volts complete all as specified and as directed. Make:- L&T Cat part No.-DBTPE008DD/Legrand cat no- 507662 or equivalent ABB/ C&S Electric Ltd.

S&F MCB 6 to 32 Amps, SP, 240 Volts ,C- Curve breaking capacity 10 KA complete all as specified and as directed. Make:- Legrand Cat Part No 408595, L & T Cat part No.BB10060C to BB10320C or equivalent in Hager/ Siemens/ ABB/ Schneider.

S&F MCB 6 to 32 Amps, DP 240 Volts ,C- Curve breaking capacity 10 KA complete all as specified and as directed. Make:- Legrand Cat Part No 408617 or equivalent in L&T Cat part No.BB20060C to BB20320C/ Hager/ Siemens/ ABB/ Schneider.

S&F MCB 6 to 32 Amps, SP, 240 Volts , 'C' curve braking capacity 10 kA including taking down old one complete all as specified and as directed.

S&F FP 63 Amps, 415 Volts ,C- Curve breaking capacity 10 KA complete all as specified and as directed. Make:- Legrand Cat Part No 408683 or equivalent in L&T Cat part No.BB40630C/ Hager/ Siemens/ ABB/ Schneider.

M&L Earthing complete with galvanised steel earth plate electrode 60 cm x 60 cm x 6.00 mm thick burried in ground (earth pit not less than 2.25 m deep below ground level) with top edge of the plate not less than 1.5 m below normal ground level, connected to GI wire 4mm as earthing lead by means of bolts, nuts, check nuts and washers of GI or steel, GI strip proected by 40 mm bore light grade GI pipe and other end connected to earth test point as directed including funnel with watering pipe 20 mm bore light grade galvanised iron, wire mesh, charcoal or coke common salt laid in alternative layer of 15 cm (complete thickness) all round the earth electrode, concrete earth pit in PCC (1:3:6) type C-1, 50 mm thick pre-cast RCC (1:2:4) type B-1 normal mix cover slab reinforced with 8 mm dia TMT bar 10 cm c/c bothways and single handle of 10 mm dia round bar including necessary excavation, earth work etc. in soft / loose soil and disposal pf soil to a distance n. exc. 50 m and necessary testing on completion all as shown in electrical plate No. 3 MES Schedule Part-I complete all as specified and as directed.

Material and labour for earthing complete with galvanised steel earth plate electrode 60 cm x 60 cm x 6.00 mm thick burried in ground (earth pit not less than 2.25 m deep below ground level) with top edge of the plate not less than 1.5 m below normal ground level, connected to GI strip 32x6 mm as earthing lead by means of bolts, nuts, check nuts and washers of GI or steel, GI strip proected by 40 mm bore light grade GI pipe and other end connected to earth test point as directed including funnel with watering pipe 20 mm bore light grade galvanised iron, wire mesh, charcoal or coke common salt laid in alternative layer of 15 cm (complete thickness) all round the earth electrode, concrete earth pit in PCC (1:3:6) type C-1, 50 mm thick pre-cast RCC (1:2:4) type B-1 normal mix cover slab reinforced with 8 mm dia TMT bar 10 cm c/c bothways and single handle of 10 mm dia round bar including necessary excavation, earth work etc. in soft / loose soil and disposal of soil to a distance n. exc. 50 m and necessary testing on completion all as shown in electrical plate No. 3 MES Schedule Part-I including taking out of old unserviceable earth pit with all accessories complete all as specified and as directed. Note-: Excavation to be measured and paid under sch item no- 1 above and PCC will be& paid under sch item no 10 above.contractor its following iteams have not been considered against items no-29 (i0 funnel with watering pipe,wire mesh and copper lugs. (ii) GI protector pipe (iii) Test point

Taking down old burnt/unserviceable submain wiring with aluminum/copper conductor PVC insulated cable of any size drawn through PVC casing caping/ PVC Conduit pipe including GI wire accessories etc. and making good disturbed surfaces of walls, floors, etc complete all as specified and directed.

M&L Sub main wiring with 2 runs of single core FRLSH type PVC insulated unsheathed stranded copper conductor of size 6.0 Sqmm and one run of PVC insulated unsheathed multistrand copper conductor FRLSH type of size 6.0 Sqmm as earth lead drawn into rigid non metalic PVC conduit of size 20 mm dia including all fittings complete all as specified and as directed. Note:- Two runs of 6.0 Sqmm conductor as main wire and one run of 6.0 Sqmm conductor as earth wire with one run of PVC conduit shall be measured as one unit.

M&L Sub main wiring with 2 runs of single core FRLSH type PVC insulated unsheathed stranded copper conductor of size 4.0 Sqmm and one run of PVC insulated unsheathed multistrand copper conductor FRLSH type of size 4.0 Sqmm as earth lead drawn into rigid non metalic PVC concealed conduit of size 20 mm dia including all fittings complete all as specified and as directed. Note:- Two runs of 4.0 Sqmm conductor as main wire and one run of 4.0 Sqmm conductor as earth wire with one run of PVC conduit shall be measured as one unit.

S&F Power supply unit consisting of starter with 11-18 Amp over load protection, MCB of 25 Amp with socket complete for AC 240 Volt single phase including taking down old unseviceable one complete all as specified and as directed.

S&F LED bed side light 12 watt design complete all as specified and as directed. Make:-Philips cat No-1739330 /Wipro- D651227/Havell's Cat No-LHEBHDP51Z1W012

Taking down and opening out the ceiling fan/wall mounted fan upto1400 mm sweep for inspection, removing bush / bearing, cleaning of bush / bearing, replacement of unserviceable / worn out bearing / bush, shaft, removing burnt out coils from the slots, cleaning and repairing of slots complete including materials like split pin,rubber reel etc reassembling spray painting including filling with cavities with filler and refixing of fan with any hook required (1.5m length) in same position or any other situation complete all as specified and as directed. Note : Spare parts shall be measured & paid separately under relevant item.

Tirupati Buildcon Pvt. Ltd.

BHARUKA ENTERPRISES

ARJUN DAS VALECHA

MAZUMDER ENTERPRISE

DEEPAK KHATTAR

JHAWAR SUPPLIERS