Provn of A veh repair shed with hard standing near adjacent to wksp floor under AGE B/R-II at Tibri Mil Stn, GE Gurdaspur.

Amount

Excavation over areas in soft/loose soil not exceeding 1.50m deep and getting out complete all as specified

Excavating in trenches, n exc 1.5m wide and n exc 1.5 m depth; for foundation, etc. or for shafts, wells, cesspits, manholes,pier holes, etc. n exc 10 sq m on plan and n exc 1.5m in depth and getting out in soft loose soil.

M&L Cement concrete type B-2, 1:2:4 using 40mm graded agregate as in foundations, filling and mass concrete.

M & L for design mix RCC type M-25 (20 mm graded agrregate stones) as in foundation , including rafts, footings , foundation beams , plinth beams, bases for columns etc basement slabs, under reamed piles and mass concrete

M & L for design mix RCC type M-25 (20 mm graded agrregate stones) as in columns, pillars, piers, posts, and struts complete all as specified

M & L for design mix RCC type M-25 (20 mm graded agrregate stones) as in beams, cantilevers, bressummers, lintels over 1.5m span.

M & L for RCC design mix M-25 (20 mm graded agrregate stones) in slab as in supported on walls , beams and columns in floors , roofs landing balconis etc as specified and directed

M&L for precast RCC 1:2:4 type B-1 using 20mm graded stone aggregate as cover slab for manhole and similar work etc complete all as specified and directed.

M & L for form work to rough finished flat surfaces of sides of concrete foundations, footings, bases of columns , raft and raft beams sides and soffits (if any) of foundation and plinth beams and similar work vertical or to batter.

M & L for form work to rough finished square/rectangular surfaces of sides of sides of pillars , posts, struts, piers, columns, and stanchions complete all as specified.

M & L for form work to rough finished flat surfaces of sides and soffits of floor or roof beams, beam haunchings, girders, bressumers, lintels, cantilevers, shelves, including supports, overhangs etc also splays between floors and beams etc complete all as specified.

M&L for form work to rough finished flat surfaces of soffits of suspended slab such as roof slab Floor slab, shelves and chajjas etc not cxc 200mm thick (Horizontal or sloping) complete.

Formwork rough finished surfaces of concrete to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, opening in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls , horizontal or sloping and similar work exc 10 cm but n exc 20 cm wide.

S&F Mild steel TMT bars 10mm dia and over cut to length, bent to shape required, including cranking bending spirally for hooping for columns , hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or scouring with clips.

S&F Mild steel TMT bars 5mm dia and over upto and including 10mm dia in stirrups, spacers, and binders cut to length, bent to shape required, including cranking bending spirally for hooping for columns , hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or scouring with clips.

Returning, filling in, including spreading, levelling , watering and well ramming in layers not exc 25 cm.in soft/loose soil

Removing excavated soil exc. 250 m but n exc 250m and depositing where directed

Rolling and consolidating formation surfaces in cutting/ filling including watering as required, filling in hollows and depression which occur during the process of rolling using 8 to 12 tonne roller to required gradient or camber complete all as specified.

Material and labour for 150 mm thick (spread thickness) soling (or sub base ) with broken boulders or quarried granite, trap or basalt stone, interstices filled, surface formed and rolled with 8 to 12 tonne power road roller and consolidated to required gradient and camber complete all as specified and directed

Cement concrete work in pavement / hard standing flexural strength 40 kg/ per sq centimetres in field using 400 kg of cement per cubic metre thickness of concrete 100mm

Forming 12 mm thick expansion joints filled with pre formed bituminous filler and top 30mm primed and sealed with sealing compound Grade 'A'

Forming contraction (dummy joints ) 30mm deep and 10mm wide filled with sealing compound grade A complete all as specified

M and L for stone set flooring with stone setts of size 200 to 250mm long , 150 to 200mm wide and 150mm deep and sides dressed bedded in CM 1:3 joints 20mm thick grouted in cement mortar 1:2 with an admixture of mettalic floor hardner 5 % by weight of cement and struck flush complete all as specified.

M and L for Edges stone to flooring with stone setts of size 250 to 300 mm long x 150 to 200mm wide and 450mm deep and sides dressed bedded in CM 1:3 joints 20mm thick grouted in cement mortar 1:2 with an admixture of mettalic floor hardner 5 % by weight of cement and struck flush complete all as specified.

S&F rolled mild steel Fe 410 Gde E-250 quality A as in roof trusses, (framed), trussed purlins, crane gantries, rails and fastenings and heavy bracket framing , base plate (Beam, tee,angle,channel or flat sections) including distance pieces , cleats/nut bolts etc complete all as specified. Note:- Truss to be fixed at a height about 6m above ground.

S&F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws as specified.

S & F 0.56mm thick plain aluminium sheeting Alloy 31000H4 in ridges , hips valiey , gutter drip and straight flashing (length and girth as fixed)

M&L Cement concrete type D-2, 1:4:8 using 40mm graded agregate as in foundations, filling and mass concrete.

M&L brick work with sub class old size 'B' bricks straight or curved on plan exc 6 mean radius built in CM 1:4.

M&L Damp proof course in Cement conrete 1:2:4type B-0 40mm thick to horizontal or vertical surfaces including necessary formwork

M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces on walls in CM 1:4. finishing even and smooth without using extra cement complete all as specified and directed

M&L for rendering 5 mm thick on fair faces of reinforced concrete surfaces on walls in CM 1:4. finishing even and smooth without using extra cement complete all as specified and directed

M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces on walls in CM 1:6. finishing even and smooth without using extra cement complete all as specified and directed

M&L for rendering 5 mm thick on fair faces of brick work or concrete surfaces on ceiling in CM 1:3. finishing even and smooth without using extra cement complete all as specified and directed

M&L for prepration of newly plastered/un plastered surfaces of wall and applying two coats of cement base paint of shade as approved over a coat of cement primer complete all as specified and directed.

M&L for preparation of new surface and applying two coats of oil bound distemper over a coat of primer on walls complete all as specified and directed

Material and labour for providing and fixing pvc insulation panel thickness 10mm with EPS stuck to 1mm plain pvc sheet suitably fixed and placed in false ceiling grid made of Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre including Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified

M&L for Prepration of newly plastered surface and applying three coat of white wash as on ceiling.

M and L for sand filling under floors or in foundation including watering and consolidation

M&L Hardcore of broken bricks, gauge n exc. 63 mm, deposited , spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface

Material and labour for cement concrete in foundation, sub base of floors and mass concrete type E-2 1:5:10 (using 40mm graded stone aggregate) complete all as specified

M&L 75mm thick Cement concrete type C-2 , 1:3:6 using 40 mm graded stone aggregate finished even and fair as in plinth protection / path complete all as specified

M&L for 25mm thick PCC 1:2:4 type B-0 (using 12.5mm graded stone aggregate) as in floor Finishing fair and even.

S&F non skid ceramic coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm in floors etc set and jointed in neat cement slurry and pointed in white or colour cement to match the colour of tiles over and including 15mm thick screed bed in CM 1:6 & complete all as specified and directed.

S&F glazed ceramic coloured tiles thick, etc. on vertical surfaces such as skirting , dados and risers to steps etc. 350x250x7mm/450x350x7mm thick set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match over and including 10mm thick rendering plaster in CM 1:4 on brick surface complete all as specified and directed.

S&F MS framed work as in door or gates of angle or other section with gusset plates,rail, braces,etc and similar work incl primer conform-ing to Fe 290 Gde E-165 complete.

Supply and fix for factory made solid Panel PVC door shutter, 30mm thick (style) consisiting of frame made out of MS tubes for top and bottom rails. M.S. frame shall covered with heat moulded plain colour PVC "C" channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail, bottom rail; panelling of plain colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement, suppling and fixing in the frame at site as per specification and drawing including fittings complete all as specified and as directed.

S&F 35mm thick Flush shutters , solid core construction , with block board core and plywood face panels, commercial type on both sides Complete all as specified and directed. ISI Marked.

S&F steel window 1.25mm thick box type (primer coated) ERW hollow P section of size 60mmx25mm double rebated comprises of glazed & gauged skelton shutter of (required no of gauged shutters and glazed shutters with or without AC opening) ERW section 50mm x 20mm & 1mm thick with one or two openable leaf consisting of two number sash bars of T-Section 20mm x 3mm complete welded to frame with one vertical mullion of ERW box type T-Section of size 60mmx25mm and 1`.25mm thick including cutting holes and making good dismantled portion in PCC 1:2:4 type B-1 (four Nos for each window) including following fittings welded to the frame shutter :- Ref Drg No CE JZ/TD-1020/08. (i) Hold fast 150mm long mild steel flat iron 12x3mm made to shape- 04 Nos per window. (ii) Handle of Z section 20mmx25mm, 100mm long – 01 No per leaf. (iii) MS tower bolt 150mm long 2 No per leaf. (iv) Z section 20mmx25mm, 100mm long stopper – 01 Nos per leaf. (v) Cleat 55mm long of hollow square 15mmx12mm - 02 Nos per leaf (vi) Fabrication and fixing arrangements as per Drg No CE JZ/TD-1020/08 (vii) MS Guard bars 12mm square bars @ 12cm c/c fixed horizontally. Note :- Glass and wire cloth shall by measured and paid separately.

S&F MS box type window/ventilator fixed type with glazing bar single as per Drg No CE JZ-1019/08 with guard bar including priming coat complete all as specified and directed. Note :- Glass/ wire cloth shall be measured and paid separately.

S&F Sheet glass figured, 3mm thick ordinary quality, in squares, not exceeding 0.50 sqm in each pane including wooden beading fixed nails complete all as specified and directed

S&F Sheet glass, 3mm thick ordinary quality, in squares, not exceeding 0.50 sqm in each pane including wooden beading fixed nails complete all as specified and directed

S&F GI wire cloth, 0.56 mm nominal dia. of wire and average width of aperture 1.18 mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and directed

S&F 300mm long Aluminium alloy. Anodised, sliding door bolt with hasp, staple ( bolt type) and fixing clips of sheet , cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed

S&F 100mm long butt Hinges, medium weight, cold rolled mild steel and fixed.

S&F200 mm Aluminium, anodised, barrel tower bolts of extruded section and fixed

S&F 150 mm Extruded aluminium alloy handles, fabricated type, anodised

S&F150 mm Aluminium, anodised, barrel tower bolts of extruded section and fixed

S&F 100 mm Extruded aluminium alloy handles, fabricated type, anodised

M&L for preparation of untreated steel/iron surfaces of any description , over 10 cm in width or girth, not otherwise described and applying two coats of sythetic enamel paint over and incl one coat of red oxide primer complete all as specified.

M&L two coats of synthetic enamel painting on wooden surfaces of any description over 10 cm in width or girth not otherwise described above pink primer including prepration of surfaces.

M&L for applying evenly a tack coat of industrial bitumen 85/25 grade @ 1.2 Kg/Sqm including cleaning surfaces etc complete all as specified and directed

S&F (minimum) 3mm thick APP film based poly meric membrance minimum weighing 3Kg per Sqm reinforced with polyester non wove fabric (weight not less than 150 gms/sqm) land on primed surface including primer @ 0.30 litre/ sqm by forced application over entire roof area with over lapping minimum 100mm to either sides and 150mm at the end and sealed in after cleaning down the roof by brooms complete all as specified and directed.

Supply and fixing vitreous china squatting pan ( Orissa Pattern) size 580 x 440 mm (white), with PVC (SWR) P or S trap, integral foot rest including water connection to trap and flushing pipe, flushing cistern etc complete and bedding in PCC 1:7:12 type F-2 all as specified. Note :- Flush pipe and flushing cistern to be measured and paid separately.

S&F 10 Ltr capacity PVC valveless symphonic action type flushing cistern white low level with ball valve flote handle including bracket and flush pipe of polythylene of low or high density or PVC,32mm dia complete all as specified and directed

S&F vitreous China wash basin white, flat back size 550mm x400mm including PTMT waste coupling 32mm bore,waste PVC pipe and cast copper alloy Pillar Tap CP fencing type 15mm size, screwed down high pressure complete

Supply & Fixing in repairs vitreous china urinal half stall type with CP cast copper alloy spreader white with grating and union for discharge pipe, including providing and fixing plug, bedding urinal against wall in cement mortar 1:2 securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back in cement fixing with brackets, flush pipe, grating and union for discharge pipe complete all as specified and directed

S&F PVC connection 15mm size with PTMT nuts of length 450mm.

S&F rotational moulded polythene, triple layers, water storage tank 500 Ltr capacity, closed top, cylindrical, hoisted and fixed in position including S&F 20mm bore PTMT ball valve epoxy coated minium weight 210gms with aluminium rod complete all as specified and directed

S&F 15mm dia GI tubes medium grade with all fitting and fixed complete to walls and ceiling or laid in floors all as specified and directed.

S&F 20mm dia GI tubes medium grade with all fitting and fixed complete to walls and ceiling or laid in floors all as specified and directed.

S&F 20mm dia GI tubes medium grade with all fitting and fixed complete laid in trenches all as specified and directed.

S&F in 15mm bore stop cock cast copper alloy CP screwed down high pressure with crutch or butterfly handle complete.

S&F in 20mm bore stop cock cast copper alloy CP screwed down high pressure with crutch or butterfly handle complete.

S&F of brass cromium brass plated fancy type bib taps 15 mm bore long nose screwed down screwed for iron pipe or for brass complete all as specified and directed

S&F 100mm dia, stainless steel grating with or without hinge type or hole type complete all specified and directed.

S&F 110mm bore PVC(SWR) pipes single socketed in any length fixed to floors or including all fittings complete all as specified and directed by Engineer-in-charge.

S&F 110mm bore PVC (SWR) bends any radius With access door

S&F 110 mm bore( SWR) vent cowl

M&L 75mm bore PVC (SWR) floor trap ,plain with grating including jointing with solvent cement

M&L for PCC 1:4:8 type D2 (using 40mm graded stone aggregate) as concrete bed, laid to falls in trenches in any depth including packing under, and haunching against the sides of RCC /SGSW pipes 150mm bore, after the pipes have been laid and tested including complete all as specified and directed

M&L salt glazed stoneware drain pipes 150mm bore laid in trenches and jointed completed with collar complete all as specified and directed.

Cutting into existing manhole of 150 mm internal diameter of pipe for connecting new drains making good to pipe and rendering cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B1 smooth finished and reforming benching as required

PCC (1:3:6) type D-2 using 40 mm graded stone aggregate as in surface channel , drains, finishing exposed surface even and smooth without using extra cement etc complete all as specified and directed

M &L for Brick work using sub class “B” bricks (old size) ,straight or curved on plan to any radius in half brick thick wall in cement mortar (1:4) complete all as specified.

M&L Extra for forming fair finished drain or channel exc 30cm inner girth in cement concrete ,using extra cement including forms, moulds , mitred/stopped ends etc complete all as specified .

Material and labor for flush pointing to brick walls in CM (1:3) complete all as specified.

KAILASH CONSTRUCTION CO

talwinder singh and co

AVTAR SINGH RAJU

Harbhajan electric co