SPECIAL REPAIR REPLACEMENT OF RUSTED GI RAISING PIPES WITH PPR PIPES AT SECTOR C AND CERTAIN REVENUE WORKS AT DINJAN MIL STATION UNDER GE DINJAN

Amount

Excavation in trenches not exceeding 1.00mtr wide and not exceeding 1.5m in depth for taking out/ laying of cables, poles, pipe line etc not exceeding 10 Sqm in plan and getting out in soft/loose soil complete all as specified and as directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick in soft/loose soil complete all as specified and as directed.

Removing and excavated materials not exceeding 50 mtr and depositing where directed at a level not exceeding 1.5 m above starting point in soil complete all as specified and as directed.

M&L for sand cushioning with dry clean sand 15cm below cable and 8cm above the cable complete all as specified and as directed. Note : Punned thickness shall be measured for payments.

Material & Labour for common burnt clay building bricks (locally available best quality), sub-class ‘B’ designation 75 of suitable size available in market to cover LT underground cables, laid dry and flat abutting each other with gaps not exceeding 10mm including taking down old unserviceable bricks complete all as specified and directed.

M&L for 32 mm bore, steel tubes, galvanised, light grade with all fittings, laid in floor/road crossing/drain etc as in UG cable protection complete to walls and ceilings or laid in floors complete all as specified and as directed.

Supply, Laying and testing cable LT XLPE sheathed,PVC insulated screened PVC bedded,galvanised steel strip of wire armoured electric power cable heavy duty with stranded aluminium conductor 1100 volt grade, laid in trenches/surface of wall/in GI pipe along with pole for connection to OH lines,including brass cable glands,clamps,etc of 2 core 16 sqmm. Note : (1) Pipes shall be measured and paid separately under relevant items of this schedule. (2) Excvation and earth work shall be measured and paid seperately.

Supply and lay 3 layer ( inner antimicrobial, outer UV stabilized) ISI marked,IS-15801 ,PP-R pipes SDR 7.4 (PN-16) and PP-R plain plain and brass threaded fittings laid in concealed work complete of size outer dia 25 mm

Supply and fix ball Valves (Brass Insert) of 25 mm bore.

M&L for Cutting existing pipe of any size for inserting of TEE for connection of PPR pipe of 32mm dia complete all as directed.

S&F ceiling fanccomplete with electronic type regulator and accessories 230 Volt, 1200mm sweep, BEE 5 star rated, complete all as specified and directed.

Burning out existing lead joint in position, including removing old lead and keeping in safe custody for re-use for CI pipe 150 mm bore complete all as specified and as directed.

Burning out existing lead joint in position, including removing old lead and keeping in safe custody for re-use for CI pipe 100 mm bore complete all as specified and as directed.

Burning out existing lead joint in position, including removing old lead and keeping in safe custody for re-use for CI pipe 80 mm bore complete all as specified and as directed.

M&L for run lead joint for cast iron spigot and socket pipes and fittings 150 mm bore with new lead and other jointing materials complete all as specified and as directed.

M&L for run lead joint for cast iron spigot and socket pipes and fittings 100 mm bore with new lead and other jointing materials complete all as specified and as directed.

M&L for run lead joint for cast iron spigot and socket pipes and fittings 80 mm bore with new lead and other jointing materials complete all as specified and as directed.

Taking up or down 50 mm bore steel water tubing galvanised including connections from trenches/wall/floor/ceiling etc and keeping serviceable quantity in safe custody for re-use at same site or other site complete all as specified and as directed. Note : Excavation and earth work shall be measured and paid separately under relevant item.

Taking up or down 40 mm bore steel water tubing galvanised including connections from trenches/wall/floor/ceiling etc and keeping serviceable quantity in safe custody for re-use at same site or other site complete all as specified and as directed. Note : Excavation and earth work shall be measured and paid separately under relevant item.

Taking up or down 25 mm bore steel water tubing galvanised including connections from trenches/wall/floor/ceiling etc and keeping serviceable quantity in safe custody for re-use at same site or other site complete all as specified and as directed. Note : Excavation and earth work shall be measured and paid separately under relevant item.

Taking up or down 20 mm bore steel water tubing galvanised including connections from trenches/wall/floor/ceiling etc and keeping serviceable quantity in safe custody for re-use at same site or other site complete all as specified and as directed. Note : Excavation and earth work shall be measured and paid separately under relevant item.

Taking up or down 15 mm bore steel water tubing galvanised including connections from trenches/wall/floor/ceiling etc and keeping serviceable quantity in safe custody for re-use at same site or other site complete all as specified and as directed. Note : Excavation and earth work shall be measured and paid separately under relevant item.

Supply, laying, connection and testing 50 mm bore, steel water tubing, galvanised iron, medium grade conforming to IS 1239 (Part -1) : 2004 with all fittings conforming to IS 1239(Part -2):2011 and fixtures laid in trenches etc complete all as specified and as directed.

Supply, laying, connection and testing 40 mm bore, steel water tubing, galvanised iron, medium grade conforming to IS 1239 (Part -1) : 2004 with all fittings conforming to IS 1239(Part -2):2011 and fixtures laid in trenches etc complete all as specified and as directed.

Supply, laying, connection and testing 25 mm bore, steel water tubing, galvanised iron, medium grade conforming to IS 1239 (Part -1):2004 with all fittings conforming to IS 1239(Part -2):2011 and fixtures laid in trenches etc complete all as specified and as directed.

Supply, laying, connection and testing 20 mm bore, steel water tubing, galvanised iron, medium grade conforming to IS 1239 (Part -1) : 2004 with all fittings conforming to IS 1239(Part -2):2011 and fixtures laid in trenches etc complete all as specified and as directed.

Supply, laying, connection and testing 15 mm bore, steel water tubing, galvanised iron, medium grade conforming to IS 1239 (Part -1) : 2004 with all fittings conforming to IS 1239(Part -2):2011 and fixtures laid in trenches etc complete all as specified and as directed.

M&L in repairs making connection of PP-R distribution branch with PP-R main of size upto 40mm outer dia by providing and fixing tee including cutting and making fusion joint etc. complete all as specified and as directed.

M&L in repairs making connection of PP-R distribution branch with PP-R main of size upto 90mm outer dia by providing and fixing tee including cutting and making fusion joint etc. complete all as specified and as directed.

S&F in repairs PP-R gate valves of size 63 mm outer dia (brass insert) connect to PP-R pipe complete all as specified and as directed.

S&F in repairs PP-R gate valves of size 32 mm outer dia (brass insert) connect to PP-R pipe complete all as specified and as directed.

S&F in repairs PP-R gate valves of size 50 mm outer dia (brass insert) connect to PP-R pipe complete all as specified and as directed.

Supply, laying, connection and testing, 25mm outer dia 3- layer PP-R polypropylene random co-polymer pipes SDR 7.4 (PN16) stablised and anti microbial fusion welded having thermal stability for hot and cold water supply all PP-R plain and brass threaded polypropylene random fittings laid in trenches complete all as specified and as directed. Note : Excavation and earth work shall be measured and paid seperately.

Supply, laying, connection and testing, 32mm outer dia 3- layer PP-R polypropylene random co-polymer pipes SDR 7.4 (PN16) stablised and anti microbial fusion welded having thermal stability for hot and cold water supply all PP-R plain and brass threaded polypropylene random fittings laid in trenches complete all as specified and as directed. Note : Excavation and earth work shall be measured and paid seperately.

Supply, laying, connection and testing, 50mm outer dia 3- layer PP-R polypropylene random co-polymer pipes SDR 7.4 (PN16) stablised and anti microbial fusion welded having thermal stability for hot and cold water supply all PP-R plain and brass threaded polypropylene random fittings laid in trenches complete all as specified and as directed. Note : Excavation and earth work shall be measured and paid seperately.

Supply, laying, connection and testing, 63mm outer dia 3- layer PP-R polypropylene random co-polymer pipes SDR 7.4 (PN16) stablised and anti microbial fusion welded having thermal stability for hot and cold water supply all PP-R plain and brass threaded polypropylene random fittings laid in trenches complete all as specified and as directed. Note : Excavation and earth work shall be measured and paid seperately.

Repacking stuffing box of sluice valve spindle (200/150/100/80 mm) , any type including taking apart and reassembling complete all as specified and as directed.

Material & Labour for filling gland packing to control water leakage in sluice valve and centrifugal/monoblock pump sets of any capacity any type as and when required incl taking down old unserviceable one complete all as specified and as directed.

M&L in repairs 20 mm dia gate valve cast copper alloy screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or for union complete all as specified and as directed.

M&L in repairs 25 mm dia gate valve cast copper alloy screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or for union complete all as specified and as directed.

M&L in repairs 40 mm dia gate valve cast copper alloy screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or for union complete all as specified and as directed.

M&L in repairs 50 mm dia gate valve cast copper alloy screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or for union complete all as specified and as directed.

S&F for 20 mm bore, ball valves high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed (Minimum weight - 210 gms) complete all as specified and as directed.

Surface dressing not exceeding 15 cm deep in soft/loose soil and rubishes to a distance not exceeding 50m including spraying pesticides (roundup or equivalent) to control the grass growth complete all as specified and as directed.

Demolition of damaged brick masonry valve pit of size 150cm x 100cm x 100 cm (internal dimensions) including concrete work and construction of similar size valve pit with one brick thick wall in cement mortar (1:4) on 100 mm thick PCC (1:4:8) type D2 (using 40mm graded broken stone aggregate) as in foundation lean concrete, including PCC (1:3:6) type C-1 (using 20mm graded crushed stone aggregate) as in benching and coping and 10mm thick cement plaster in CM (1:4) internally and externally upto 15cm below ground level providing valve pit cover made out of 40x40x6mm angle iron frame all-round fixed by means of 4 Nos holdfast 150mm long made out of flat iron 40x6mm embedded in PCC block (1:2:4) type B-1 (using 20mm graded crushed stone aggregate) of size 230x200x100mm incl provn of hinges welded with angle iron frame and MS cover 3mm thck sheet, MS handle of suitable length and size welded with MS cover and suitable locking arrangement and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed.

Demolition of damaged brick masonry valve pit of size 45cm x 45cm x 45 cm (internal dimensions) including concrete work and construction of similar size valve pit with one brick thick wall in cement mortar (1:4) on 100 mm thick PCC (1:4:8) type D2 (using 40mm graded broken stone aggregate) as in foundation lean concrete, including PCC (1:3:6) type C-1 (using 20mm graded crushed stone aggregate) as in benching and coping and 10mm thick cement plaster in CM (1:4) internally and externally upto 15cm below ground level providing valve pit cover made out of 40x40x6mm angle iron frame all-round fixed by means of 4 Nos holdfast 150mm long made out of flat iron 40x6mm embedded in PCC block (1:2:4) type B-1 (using 20mm graded crushed stone aggregate) of size 230x200x100mm incl provn of hinges welded with angle iron frame and MS cover 3mm thck sheet, MS handle of suitable length and size welded with MS cover and suitable locking arrangement and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed.

M&L for preparation of old painted steel surfaces (horizontally or vertically 18 mtr height) and applying one coat of synthetic enamel paint any description over 10 cm in width or girth not otherwise described with colour as approved including temporary bamboo stagging arrangement as required complete all as specified and as directed.

Demolition of plain cement concrete (unreinforced) in ground floors and pavings not exceeding 15 cm thickness. (below or above ground level) complete all as specified and as directed.

M&L for plain cement concrete (1:3:6) type C-1 (using 20 mm graded stone aggregate) in foundation of pipe supports/platform etc. including necessary form work complete all as specified and as directed.

M&L for rendering 10 mm thick in cement mortar (1:4) on fair faces of brick masonry or concrete surfaces and finishing the surfaces even and fair without using extra cement complete all as specified and as directed.

M&L for cast iron fittings for spigot and socketed pipe, such as bends (any type, radius and angle) tapers any type, (straight, bend, increasing, decreasing or double socket etc.) Tee pieces single branch. "Y" junction, double branch, cross (all sockets or socket and pigot) collars, caps and plugs etc upto 150mm bore complete all as specified and as directed.

M&L for concealed point wiring with FRLSH PVC insulated unsheathed multistranded copper conductor cables of 1.5 sqmm size alongwith one earth continuity conductor with FRLSH PVC insulated unsheathed multistranded copper conductor cable of 1.5 sqmm size passing through and including suitable PVC conduit with all fittings and accessories of PVC conduit (like Tee, bend etc.) complete fixed to walls /ceiling etc , including cutting chases, making good with cement mortar 1:3, terminated in and including providing PVC/modular metal box of suitable size with 3mm thick hylam sheet cover for fixing of switches, sockets, fan regulators etc for one light/fan/bell/buzzer point controlled by one, one way switches complete all as specified and as directed. Note :- Cost of PVC conduit, cutting chases of wall, making good disturbed wall surfaces including finishing with cement mortor 1:4, matching with existing colour/paint of surface are deemed to be included in the quoted rate.

All as per item No 52 above but for one 3 pin 5 Amps, socket outlet, on Independent board.

All as per item No 52 above but for one 5 Amps, 3 pin socket outlet on the same board with other switches.

All as per item No. 52 above but wiring with cables of size 2.5 sqmm & cables of size 2.5 sqmm as continuous earth wire for one 15/16 amp multi socket out let on independent board.

S&F for switch piano, flush type single pole, 230 volts, 5 Amp one way bearing ISI marked complete all as specified and as directed.

S&F for socket outlet, 2 in 1, 3 pin, 5 Amps, 240V bearing ISI marked complete all as specified and as directed.

S&F for switch socket combination, 2 in 1, 5 Amps, flush type, 240 volts bearing ISI marked complete all as specified and as directed.

S&F for switch socket combination, 5 in 1, 5/16 Amps, 240 volts, bearing ISI marked flush type complete all as specified and as directed.

S&F for ceiling rose, 3 phase/ PVC/ polycarbonate, isolated body bearing ISI marked and including PVC box complete all as specified and as directed.

S&F for stepped type (five steps), electronic fan regulator, flush type (socket type) complete all as specified and as directed.

S&F in repair lamp holder PVC/Polycarbonate type with back plate suitable for batten fittings including 9 watt LED lamp complete all as specified and as directed.

S&F 20 Watt surface and wall mounting type LED batten with polycarbonate housing & integrated complete all as specified and as directed.

S&F in repairs 25 Watt LED building security light new generation energy saving and environmental friendly long life LED street light made up of pressure die cast aluminium housing with high power LED as lighting source and lens embeded PC cover having TOP OPENING separate driver compartment with IP65 protection and impact resistance of IK07 including all fixing arrangement and taking down old light fittings of any type complete all as specified and as directed.

Supply and fixing in repair of MCB Distribution board SPN 4 Way for mounting SPN/ SP MCBs as Incoming / outgoing, factory made, confirming to IS, fabricated out of CRCA sheet , fitted with DIN channel, neutral link and suitable rated bus bar, DBs shall be semi glossy finished with epoxy polyester based powder paint sprayed and backed at high temperature, between powder paint process the sheet steel having to go through the anti rust conditioning in not less than seven tank process to ensure smooth finish and protection against corrosion atmosphere. The DBs shall be double door type with hinged door with locking arrangement. The DBs shall be of IP 43 - IK 09 with metal door complete all as specified and directed by Engr-in-charge.

S&F for factory made board distribution (DB) double door in sheet metal enclosure with common bus bar at incomming end, single pole & neutral, 8 way, 240 Volts suitable for housing MCBs including complete all as specified and as directed.

Supply & fix of MCB double pole 6-32 Amps, 'C' Series 10 KA 240 volts complete all as specified and directed.

Supply & fix of MCB SPN 40 Amps, 'B' Series 10 KA 240 volts complete all as specified and directed.

Supply & fix of MCB SP 6-32 Amps, 'B' Series 10 KA, 240 volts complete all as specified and directed.

Supply & fix of MCB dummy blank plate complete all as specified and directed.

Material and labour for earthing complete with galvanised steel earth plate electrode of size 600 x 600 x 6 mm thick, burried directly in ground (earth pit not less than 2.25 m below normal ground level) with top edge of the plate not less than 1.5 m below normal ground level connected to galvanised wire of dia 4 mm as earthing lead by means of nuts, bolts and washers of galvanised iron and earth lead protected by galvanised iron pipe 15 mm bore (light grade) and connected to earth test point and including cement concrete pit in PCC (1:3:6) type C-1(using 20 mm graded aggregate) and pre-cast RCC cover slab of size 540 x 540 x 50 mm thick, reinforced with 8 mm dia TMT bars both ways and one handle for lifting made with 10 mm dia mild steel bar,funnel, wire mesh 20 mm bore galvanised (light grade) for watering, charcoal and salt in alternate layers including necessary execuation and eath works in any types of soil complete all as shown on Electrical plate No 3 of MES SSR-I including taking out the old earthing material complete all as specified and directed. Note:No extra payment will be for the earthing GI wire of size 4 mm dia

Supply & fix exhaust fans metallic body AC single phase 230/240V of size 300mm sweep with louver complete all as specified and directed.

M&L for cutting of circular hole at any type of wall suitable size for fixing of exhaust fan of size 300mm sweep, grouting 04 Nos 100mm long 12mm dia stud bolt including,making good to disturbed surfaces of wall and colour wash to match as per the existing colour complete as directed and specified by engineer-in-charge.

S&F street light bracket fabricated out of GI Tubing light grade 32 mm bore Bend to the shape as directed and of length 1.5 mtr complete with mounting MS clamp of flat iron size 40X5mm of suitable length 02 pairs incl nut bolts etc of suitable size, including taking down old corroded one all as specified and directed.

M&L for 15 mm bore, steel tubes, galvanised, light grade with all fittings, laid in floor/road crossing/drain etc as in UG cable protection complete to walls and ceilings or laid in floors complete all as specified and as directed.

S&F 15mm bore bib taps cast copper alloy, screwed down high pressure with crutch or butterfly handle fancy type chromium plated screwed for iron pipe for brass furule and fixed complete all as specified and directed.

S&F 15 mm bore dia cast copper alloy fancy type, chromium plated stop valves, crewed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed.

Excavating in post holes ( or similar holes) each n.exc 0.5 cum getting out , returning, filling in and ramming earth or broken rubble mixed with earth around, in layers n.exc 25 cm watering, and removing surplus soil to a distance n.exc 50m and making good surface, in soft/loose soil.

Demolition of unreinforced cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed

M&L for plain cement concrete (1:3:6) type C-2, (using 40 mm graded stone aggregate) as in foundation filling and mass concrete for fixing post , etc complete all as specified and as directed.

M&L for plain cement concrete (1:4:8) type D-2 (using 40 mm graded stone aggregate) as in foundation filling and mass concrete, etc complete all as specified and as directed.

S&F for rolled mild steel in steel work tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS.1161- 1979 grade St.-240 complete all as specified and as directed.

S&F for rolled mild steel work in Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, with riveted, bolted or welded attachment quality confirming to Fe-290 (Gde E-165) as specified and as directed.

M&L for hardcore of broken stone aggregate of guage n.exc 63mm , deposited, spread and levelled in layers n exc. 15 cm thick, consolidated, watered and rolled/rammed to a true surface complete all as specified and as directed.

M&L for 100 mm thick plain cement concrete (1:3:6), type C2 (using 40mm graded stone aggregate) as in sub base of floor, etc complete all as specified and as directed.

S&F for 0.50mm thick Hi-rib trapezoidal corrugated pre-painted galvalume steel sheet (1060mm) of 550 Mpa strength with 30mm crest height and 200mm pitch distance with guard film, side lap and end la as in roof covering, fixed with self tapping screws / 'J' type crank hook bolts and washers as per manufacturer's instruction complete all as specified and as directed.

M&L for preparation of new steel surfaces of any description, over 10 cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of zinc chrome red oxide primer complete all as specified and as directed.

M&L for preparing newly plastered surfaces of walls, etc and applying three coats of white wash complete all as specified and as directed.

M&L for preparation of new plastered surfaces of ceiling and applying three coats of white wash complete all as specified and as directed.

M&L for plain cement concrete (1:3:6) type C-2, (using 40 mm graded stone aggregate) as in surface channel, drains, batching of manholes etc complete all as specified and as directed.

M&L for 75 mm thick plain cement concrete (1:3:6), type C1, (using 40mm graded stone aggregate) as in plinth protection, finishing surface even and smooth without using extra cement, complete all as specified and as directed

M&L for 100 mm thick plain cement concrete (1:3:6), type C2 (using 40mm graded stone aggregate) as in sub base of floor, etc complete all as specified and as directed.

M&L for brick work with sub class 'B' bricks straight or curved on plan exceeding 6 m mean radius built in cement mortar (1:6) complete all as specified and as directed.

M&L for brick work with sub class ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar in (1:4) complete all as specified and as directed

M&L for rendering 15 mm thick in cement mortar (1:6) on other than fair faces of brick masonry or concrete surfaces and finishing the surfaces even and smooth without using extra cement complete all as specified and as directed.

M&L for rendering 15 mm thick on fair faces of external wall of brick work or stone surfaces in two layers (10 mm and 5 mm thick) in cement mortar (1:4) using water proofing compound in top layer (water proofing compound measured as separately) and finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 15 mm thick of internal wall on fair faces of brick work or concrete surfaces in cement mortar in (1:4) and finished even and smooth with using extra cement complete all as specified and directed.

M&L for rendering 5 mm thick on ceiling in cement mortar (1:3) finished even & smooth without using extra cement complete all as specified and directed

Supply only Liquid water proofing compound complete all as specified and directed.

M&L for non-skid coloured ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, as in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15 mm thick screed bed or bedding layer of cement mortar in (1:6) for laying floor finishes complete all as specified and as directed

M&L for coloured glazed ceramic tiles in vertical surface of size 450X 350X 7 mm thick over 10 mm thick back coat of cement mortar in (1:4) set and jointed in neat cement slurry and pointed in white or colour cement to match over complete all as specified and as directed.

M&L for RCC (nominal mix ) type B1 1:2:4 (20 mm graded aggregate) in foundations, including rafts, footings, foundation beams ; plinth beams; bases for columns, etc ; basement slabs, under reamed piles and mass concrete complete all as specified and directed.

M&L for RCC (nominal mix ) type B1 1:2:4 (20 mm graded aggregate) in Beams, cantilevers, bressummer, lintels over 1.5 span complete all as specified and directed.

M&L for reinforced cement concrete 1:2:4 (nominal mix) , type B-1 (Using 20 mm graded stone aggregate) as in slab supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves etc complete all as specified and directed. (Note : reinforcement shall be measured and paid separately against respective item).

M&L for RCC (nominal mix ) type B-1, 1:2:4 (20 mm graded aggregate) in columns, pillars, piers, post and struts etc complete all as specified and directed.

M&L for RCC (nominal mix ) type B-1, 1:2:4 (20 mm graded aggregate) in chajjas complete all as specified and directed.

Use and waste of form work to flat sides of cocnrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams ; and similar work ; vertical or to batter complete all as specified and directed.

Use and waste form work to flat sides of soffits of floor or roof beams, beam hauching, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc also splays between floors and beam, etc complete all as specified and directed.

Use and waste form work to flat sides of pillars, posts, struts, piers, columns and stanchions complete all as specified and directed.

S&F form work to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200 mm thick (Horizontal or sloping) for flat rough finished surfaces of concrete complete all as specified and directed.

S&F for mild steel TMT steel bars 10mm dia and over, cut to length, bend to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and as directed.

M&L for mild steel TMT bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders ,cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and as directed.

S&F for solid PVC door frames of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube complete all as specified and as directed.

S&F for factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded, plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour 5mm thick PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement, complete all as specified and as directed by Engr-in-Charge.

S&F 75 mm size stainless steel, butt hinges, medium weight, cold rolled, complete all as specified and as directed.

S&F 150 mm long, aluminium handles, cast type, anodised complete all as specified and as directed.

S&F 150mm long aluminium, anodised, barrel tower bolts of extruded section complete all as specified and as directed.

S&F for steel ventilators with top hung shutter including two pairs of brass cup pivots, catch spring and pulley wheel complete all as specified and as directed.

S&F for 4 mm thick, Figured glass, pin head type and glazing with oil putty in squares n exc 0.5 sq. m in each pane complete all as specified and as directed.

S&F for vitreous china bowl urinal, flat back size of 465x355x265mm whitw with grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe) but fixing plug bedding urinal against wall in cement mortar (1:2) securing urinal to plug including 60mm long brass screws pointing around urinal back in cement mortar including 15mm brass stop cock and waste coupling brass CP complete all as specified and as directed.

S&F vitreous china wash basin, size 550x400mm, white, flat back, with PVC waste pipe, CP waste coupling, chain, plug and porcelain stopper & brackets including cutting for and pinning in ends of brackets but excluding tap complete all as specified and as directed. Make : Cat No. C0406 of Parryware/Hindware/Cera.

S&F PVC low level flushing cistern, 10 litre capacity, valveless, symphonic action type with inlet, ball valve, float and handle incl bracket, PVC conection pipe and flush pipe of polyethylene of low or high density or PVC 32 mm dia complete all as specified and directed

S&F vitreous china squatting pan, 'Orissa' pattern, size 580 x 440 mm white with integral foot rest and 'P' or 'S' trap, including provision of lime concrete bedding, connection to trap and flushing pipe providing 110mm PVC WC connector etc complete including making good to disturbed surfaces of floor to match with existing specifications complete all as specified and as directed.

S&F vitreous china wash down water closet pan (closed pattern), wall hung EWC/ white/ ivory/ off white, including connection to outgoing drain and flushing pipe, anti syphonic pipe with seat and cover, including flushing cistern and flush pipe complete all as specified and as directed.

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth complete all as specified and directed.

S&F in repairs 15 mm bore, bib taps, cast copper alloy, chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and as directed.

S&F 15mm dia angular stop cock cast copper alloy, screwed down high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions complete all as specified and as directed. Make : Cat No. T3507A1 of Parryware/Hindware/Cera.

S&F 15mm stop valves (concealed type), cast copper alloy fancy type chromium plated, long sunk and cup, screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed.

S&F 15 mm bore, pillar taps, fancy type, cast copper alloy, chromium plated with capstan heads, screwed down high pressure with or without lettered 'Hot or Cold' with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and as directed.

S&F 15mm bore, PVC connection pipe 600mm long with PTMT nuts at both ends complete all as specified and as directed.

S&F for brass chromium plated shower rose, 125 mm size, with or without swivel joint any size incl fixing to steel pipe or union complete all as specified and as directed

S&F for 75mm dia, PVC (SWR) floor trap, plain with grating including jointing with solvent cement to waste pipe fixed in cement concrete type B-1 (1:2:4), complete all as specified and as directed.

M&L for Salt-glazed stoneware gully traps of size 150 x 150 mm, square or round mouthed, type 'P', complete all as specified and as directed.

S&F for 20mm bore, gun metal gate valves with iron wheel head screwed both ends for iron pipes or for unions complete all as specified and as directed.

S&F in repairs 50mm bore, high density poly-ethylene pipes (HDPE) of pressure rating 6 kgf/cm2 fixed to wall, ceiling or in floors complete all as specified and as directed.

Supply, laying, connection and testing, 15mm bore, steel water tubing, galvanised, medium grade conforming to IS 1239 (Part -1):2004 with all fittings conforming to IS 1239 (Part -2):2011 and fixtures fixed to walls and ceilings or laid in floors, etc complete all as specified and as directed.

Supply, laying, connection and testing, 20mm bore, steel water tubing, galvanised, medium grade conforming to IS 1239 (Part -1):2004 with all fittings conforming to IS 1239 (Part -2):2011 and fixtures fixed to walls and ceilings or laid in floors, etc complete all as specified and as directed.

S&F for brass chromium plated tubular towel rail, D type, 60cm long, 20mm dia with brackets complete all as specified and as directed.

M&L for salt glazed stone ware drain pipes 150 mm bore, grade 'A' laid in trenches, jointed and tested complete all as specified and as directed.

M&L for plain cement concrete (1:3:6) type C-2 (using 40 mm graded stone aggragate) as in concrete bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for 150 mm bore SGSW/RCC drain pipes complete all as specified and as directed .

S&F 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls complete all as specified and as directed.

S&F in repairs 75 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls complete all as specified and as directed.

S&F for 110 mm bore PVC (SWR) junction single, (Single T) equal or unequal complete all as specified and as directed.

S&F for 110 mm bore PVC (SWR) bends any radius complete all as specified and as directed.

S&F for 110 mm bore PVC (SWR) bends with acces any radius complete all as specified and as directed.

S&F for 75 mm bore PVC (SWR) bends any radius complete all as specified and as directed.

S&F for 75 mm bore PVC (SWR) bends with acces any radius complete all as specified and as directed.

S&F for 110mm PVC (SWR), reducers complete all as specified and as directed.

S&F for 110 mm bore PVC (SWR) vent cowl complete all as specified and as directed.

M&L for cutting into existing manholes for connecting new drains, making good to pipe and plastering the distrubed portions in cement mortar (1:3) to match with surround surfaces, cutting out existing benching and forming branch channel (1/2 round or 3/4 round section) in cement concrete (1:2:4) type B-1 finished smooth and reforming benching as required for 150/160mm bore pipe complete all as specified and as directed.

S&F for 1000 litres capacity rotational moulded polyethylene water storage tanks (cylindrical or vertical with closed top) as per IS 12701:1996, hoisted and fixed in position including provision of 20/15mm bore medium grade pipe for connecting inlet, outlet, overflow and washout pipe complete all as specified and as directed.

S&F for 20 mm bore, ball brass valves, high pressure, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and as directed.

CHETIA CONSTRUCTION

M/s GANDHESWAR PHUKAN

Construction House

R D Enterprises

M/S Build Tech

M/S BORAH BROTHERS