Loading…
Loading…
| # | Company | Quoted % | Amount | Rank | Status |
|---|---|---|---|---|---|
| 1 | L1₹37.5 LAdmitted-Finance | -24.99% | ₹37.5 L | L1 | Admitted-Finance |
| 2 | L2₹47.5 LAdmitted-Finance | -5.04% | ₹47.5 L | L2 | Admitted-Finance |
| 3 | Rejected-Technical | - | - | - | Rejected-Technical Non Responsive |
Tender Value
₹50 L
EMD Value
₹1 L
Closing Date
29 Dec 2025, 5:00 pmClosed
VMOU, Kota
VMOU, Kota
Annual Rate Contact for Civil Maintenance Work in University Campus, Kota
2025_VMOU_521236_1
NIB No. 20/2025-26
Open Tender
Civil Works
365 days
Kota
Please refer Tender documents.
2 documents required · 2 mandatory
₹1,500
VMOU, Kota
₹1 L
12 Jan 2026
18 Dec 2025
30 Dec 2025
18 Dec 2025
29 Dec 2025
18 Dec 2025
Earth work in rough excavation, banking excavated earth in layers not exceeding 20cm in depth, breaking clods watering, rolling each layer with 1/2 tonne roller, or stone or steel rammers and rolling every 3rd and top- most layer with power roller of minimum 8-10 tonne capacity and dressing up in embankment for roads, flood banks marginal banks and guide banks or filling up ground depressions, lead up to 50 Mtr. and lift up to 1.5 Mtr. All kinds of soil
Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30cm in depth. 1.5m in width as well as 10 sqm on plan) including disposal of excavated earth, lead upto 50m and lift upto 1.5 mtr., disposed earth to be levelled and neatly dressed : All kinds of soil
Earth work in excavation/ by mechanical means (Hydraulic Excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5m in width as well as 10 sqm on plan) including disposal of excavated earth, lead upto 50 m and lift upto 1.5 m, disposed earth to be levelled and neatly dressed: Ordinary rock.
Hard rock (blasting prohibited) useful material 30%
Providing and Fixing M.S. sheet 1mm thick single leaf door shutter in angle iron frame 35×35×5mm suitably diagonally braced with 25×3mm flat iron above and below lock rail of size 50×5mm beading extra including all fittings, as per direction of Engg. incharge but excluding cost of chowkhats : including two coats of anit-corrosive red oxide primer paint.
Add extra for double leaf shutters.
Earth work in excavation by mechanical means (Hydraulic Excavator)/ manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including taking out the excavated soil and depositing and refilling of jhiri with watering & ramming and disposal of surplus excavated soil as directed with in a lead of 50 meter. All kinds of soils
Excavating trenches of required width for pipe cables, etc. including excavation for sockets, and dressing of sides, ramming of bottoms, depth up to 1.5 Mtr. including taking out the excavated soil, and then returning the soil as required in layers not exceeding 20cm in depth including consolidating each deposited layer by ramming, watering etc. and disposal of surplus excavated soil as directed within a lead of 50 Mtr.: All kinds of soil. Pipes cables etc. not exceeding 80 mm dia.
Pipes cables, etc. exceeding 80mm dia but not exceeding 300mm dia.
Filling available excavated earth (excluding rock) in trenches, plinth side of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering including lead up to 50 meter and with all lift.
Supplying and Filling in plinth with river sand under floors including watering ramming consolidating and dressing complete including cost of sand.
Supplying and Filling in plinth with blown sand under floors including watering ramming consolidating and dressing complete including cost of sand.
Surface dressing of the ground including removing vegetation and inequalities not exceeding 15cm deep and disposal of rubbish lead up to 50 Mtr. and lift up to 1.5 Mtr. : All kinds of soil.
Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth upto 30 cm measured at a height of 1 m above ground level and removal of rubbish upto a distance of 50 m outside the periphery of the area cleared.
Clearing grass and removal of the rubbish upto a distance of 50 m outside the periphery of the area cleared.
Diluting and injecting by hand operated pressure pumps chemical Emulsion timber ground treatment [TCGT] in ratio 1:2 as per manufacturers specification for POST CONSTRUCTIONAL Anti-termite treatment (as per IS 6313) part - III 1971 as amended from time to time) (excluding the cost of chemical emulsion) :
Along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. with Chlorpyriphos / Lindane E.C. 20% with 1% concentration
Treatment of existing masonry using chemical emulsion@ one litre per hole at 300mm interval including drilling holes at 45 degree and plugging them with cement mortar 1:2 (1 cement : 2 coarse sand) to the full depth of the hole. With Chlorpyriphos/Lindane E.C. 20% with 1% concentration
Anti-termite treatment of existing floor and wall using Imidacloprid 30.5% EC non repellent, odorless, low dose, environmentally safe Termiticide with rapid action non corrosive stain free, by injecting the emulsion as per specification and plug
ging with cement mortar 1:2 (1 cement : 2 coarse sand) in the whole floor area. The pesticide emulsion of imidacloprid 30.5% EC mixed with water in the ration of 1:474 will be pumped by a motorized spray pump specified manner. The net floor and wall area treated will be measured for payment.
Anti termite treatment of floor using Imidacloprid 30.5% EC non repellent, odorless, low dose, environmentally safe terniticide with rapid action non corrosive stain free, by drilling 12mm diameter holes 300mm apart injecting the emulsion as per specification and plugging with cement mortar 1:2 (1 cement : 2 coarse sand) in the whole floor area DPE 12mm dia termitube system with required number of junction boxes are to be installed. The termitube will run all along the perimeter wall both inside & outside. In the middle area the termitube to be installed at an interval of 1.00 mtr. or less both ways as required with sufficient number of junction boxes to pump the emulsion. After successful testing of termitube, pesticide emulsion of imidacloprid 30.5% EC mixed with water in the
ration of 1:474 will be pumped by a motorized spray pump from the junction box in specified manner. The plinth area of the area treated will be measured for payment.
Providing and Laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering - All work up to plinth level.
M-20 grade Nominal Mix, 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20mm nominal size).
M-15 grade Nominal Mix, 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size).
Anti termite treatment of floor using Imidacloprid 30.5% EC non repellent, odorless, low dose, environmentally safe terniticide with rapid action non corrosive stain free, by drilling 12mm diameter holes 300mm apart injecting the emulsion as per specification and plugging with cement mortar 1:2 (1 cement : 2 coarse sand) in the whole floor area DPE 12mm dia termitube system with required number of junction boxes are to be installed. The termitube will run all along the perimeter wall both inside & outside. In the middle area the termitube to be installed at an interval of 1.00 mtr. or less both ways as required with sufficient number of junction boxes to pump the emulsion. After successful testing of termitube, pesticide emulsion of imidacloprid 30.5% EC mixed with water in the
ration of 1:474 will be pumped by a motorized spray pump from the junction box in specified manner. The plinth area of the area treated will be measured for payment.
Providing and laying damp-proof course with cement concrete grade M-150 (1:2:4) mortar prepared with 1% solution of water-proof compound complete as per specification. 75 mm thick.
Brick work with F.P.S. bricks of class designation 75 in superstructure above plinth level upto floor V level in all shapes and sizes in : Cement mortar 1 : 6 (1 cement : 6 coarse sand)
Half brick masonry in Superstructure, above plinth level upto floor V level using bricks of designation 75 in : Cement mortar 1:6 (1cement : 6 coarse sand)
Brick work in partition in super structure upto five storey 7cm thick (brick on edges) using bricks of class designation 75 in : Cement mortar 1: 4 (1 cement : 4 coarse sand)
Random Rubble stone masonry for with hard stone in foundation and plinth in Cement Sand mortar above 30 CM thick wall in : Cement Mortar 1:6 (1 cement : 6 sand).
Random Rubble stone masonry with hard stone in superstructure above plinth level and upto five level above 30cm thick walls in : Cement Mortar 1:6 (1 cement : 6 sand).
Add extra for facing as per design and detailed specifications including additional cost of stones. Course rubble facing Second sort.
Providing and Fixing stainless steel cramps of required size and shape for anchoring stone wall lining to the backing or securing adjacent stones in stone wall lining in cement mortar 1:2 (1 cement : 2 coarse sand) including making the necessary chases in stone and holes in walls wherever required.
Supplying and Fixing in walls machine cut and polished stone shelves, tands and in CM 1:3 with machine cut edges : Sand or other approved stone 25 mm thick.
Providing and Fixing Marble stone flooring table rubbed, 15-18 mm thick over 20mm (Av.) thick base of CM 1:4 (1 cement : 4 coarse sand) jointing with white cement mortar 1:2 (1 white cement : 2 marble dust) with pigment to match the shade of the marble slab in
cluding grinding, rubbing and polishing complete. OR Providing and Fixing stone slabs table rubbed, 15-18 mm thick in Walls, Steps, Pillars, Counters, Jambs, Shelves, Sills etc. laid on 12mm (Av.) thick base of CM 1:3 (1 cement : 3 coarse sand) jointing with white cement mortar 1:2 (1white cement : 2 marble dust) with pigment to match the shade of the marble slab including grinding, rubbing and polishing complete. Makrana ‘Adanga’ 1501 Cm2 to 3600 Cm2 Tiles.
Providing and Fixing Granite stone slab mirror polished and machine edge cut in walls, pillars, steps, Shelves, Sills Counters, Floors etc. laid on 12mm (Av.) thick base of cement mortar 1:3 (1 cement : 3 coarse sand) jointing with white cement mortar 1:2 (1white cement : 2 marble dust) with pigment to match the shade of the marble slab including grinding, rubbing and polishing complete. South (Red)
1501 Cm2 to 3600 Cm2 Tiles
Above 3601 Cm2 Slabs
Extra for providing edge moulding to 15-18mm thick marble/ Granite/Kota stone counters, Vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. Marble work. Full Edge moulding
Granite/Kota Stone Work – Full Edge moulding
Fixing chowkhats in existing opening including embedding chowkhats in floors or walls cutting masonry for holdfasts embedding hold fasts in cement concrete blocks with cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) painting two coats of coal tar to sides of chaukhats and making good the damages to walls and floors as required complete including disposal of rubbish to the dumping ground within 50 metres lead.
Repairs to plaster of thickness 12mm to 20mm in patches of area 2.5 sq. metres and under including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete including disposal of rubbish to the dumping ground within 50 m lead With cement mortar 1:4 (1 cement : 4 coarse sand)
Extra for using Marble printed/ Granite shade or dark shade tiles instead of white, grey, ivory, fume red brown, light green, light blue and other light shades in glazed tiles and MAT finished tiles.
Extra for using size above 200×300mm in glazed tiles and for using 400mm×400mm MAT finished tiles in place of 300mm × 300mm size.
P & F 1st Quality Vitrified Porcelain Polished tiles on floor, skirting and steps etc. in different sizes (thickness to be specified by manufacturer) with water absortion less than 0.08% and conforming to IS 15622 of approved make in all colour and shade, laid with 20 mm thick CM 1:4 including grounting the joints with white cement and matching pigment etc complete. Size 600 mm × 600 mm
Add extra for Fixing glazed/ Ceramic/ Vitrified floor tiles with cement based high polymer modified quick-set tile adhesive (Water based) conforming to IS: 15477 , using 5kg. adhesive per sqm of tile area, in average 3mm thickness instead of cement mortar.
P & F 1st Quality Heavy Duty Vitrified Polished Digital tiles on floor, skirting and steps etc. in different sizes (thickness minimum 10mm) with water absortion less than or equal 0.08% and conforming to IS-15622 of approved make in all colour and shade, laid with 20 mm thick CM 1:4 including grouting the joints with white cement and matching pigment etc complete. Size 600 mm × 1200 mm
Providing non slip grooves to granite/ kota stone flooring, counters, vanities etc. using groove cutter V type including machine polishing to groove to give high gloss finish etc. complete as per design approved by engineer in charge
Granite/Kota Stone Work – Half Edge moulding
IS 710-1976 marked 9 mm thick Teak BWR ply both side
IS 710- 1976 marked 12 mm thick commercial ply
IS 710-1976 marked 19 mm thick commercial ply
IS 710-1976 marked 12mm thick Teak ply BWR both side
Wire gauge 24 gauge 14 mesh of IS 1568-1970 marked 85 gauge of dia 0.56 mm
SS wire gauge 14 mesh × 24 gauge
ISI 2202-67 marked using Phenol formal dehyderesin in glue both sides with approved steel fittings complete as per annexure 'A' : Commercial Veneer both side 30 mm thick.
Providing and Fixing external grade board solid core single leaf flush door shutters
Extra for providing external lipping with 2nd class teak wood battens 6 mm minimum depth on all edges of shutters (over all area of door shutter to be measured) Over item no. 8.13.
Providing and Fixing wall panelling using soft wood frame of size 50×25mm @600 mm c/c in both directions duly treated with anti-termite treatment making grooves painting of grooves specification and drawing using : ISI-9 mm teak ply one side BWR
Providing and Fixing expandable fastners of specified size with necessary plastic sleeves and galvanised M.S. screws including drilling holes in masonry work /CC/R.C.C. and making good etc. complete.
25 mm long
32 mm long
40 mm long
Providing and Fixing Nigeria / Ghana / Ivory Coast Teak wood grade-I mouldings and beadings in doors and windows size : 25×12 mm
Providing and Fixing 18 mm thick, 150 mm wide pelmet of flat pressed 3 layer or graded wood particle board medium density grade-I, IS:3087 marked including top cover of 6 mm commercial ply wood conforming to IS: 303 BWR grade, nickel plate MS-20 mm dia curtain rod with nickel plated bracket including fixing with 25×3 mm MS flat 10 cm long all complete
Providing and Fixing curtain rods of 1.25 mm thick chromium plated brass plate, with two chromium plated brass brackets fixed with C.P. brass screws and wooden plugs, etc., wherever necessary complete: 20 mm
Providing and Fixing IS:3564 marked Aluminium die cast body tubular type universal hydraulic door closer with necessary accessories and screws etc. complete.
Providing and fixing bright finished Mortice lock of approved make Godrej or equivalent with pair of CP handles for doors with necessary screws etc complete (Best make of approved quality) as per direction of Engineer-in-charge.
Providing and fixing Almirah lock (50 to 70 mm size) of approved make without pair of handles for door with necessary screws etc. complete as per direction of Engineer-in-charge.
Providing & Fixing of ward robe shutters made out of 19mm thick BWP block board ISI of superior quality make with following details
Extra for Fixing marble /granite stone over and above corresponding basic item, in facia and drops of width upto 150 mm with epoxy resin based adhesive including cleaning etc. complete.
Providing and Fixing cramps of required size & shape in RCC/ CC backing with cement mortar 1:2 (1 cement : 2 coarse sand) including drilling necessary hole in stones and embedding the cramp in the hole . Stainless steel cramps.
Providing and Fixing 1st quality standard white, grey, ivory, fume red brown, light green, light blue and other light shades glazed tiles confirming to IS : 13753 & IS:15622 of size 200mm×300mm in walls, floors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in the white cement mixed with pigment to match the shade of the tile complete (excluding the cost of cement plaster on walls and pillar).
Providing & Fixing mica of approved make for inner/outer side of shutters with fevicol & nails complete as per approved by engineer in charge. 0.6 mm thick mica.
0.8 mm thick mica.
Providing & Fixing decorative veneer of approved make for inner/outer side of shutters with fevicol & nails complete as per approved by engineer in charge. 4.0 mm thick veneer.
Providing and Fixing S.S. Rod 30mm dia (304 grade, 16 SWG) including brackets fixed with C.P. brass screws and rawl plugs, etc., wherever necessary complete two side central all fittings.
Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry, making of lines or groove etc complete but excluding the cost of nosing of steps etc. complete. 40 mm thick with 20 mm thick nominal size aggregate.
30 mm thick - Shesham wood grade-I
Providing and Fixing wood panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled and glazed shutter 25 mm to 40 mm thick. Wood panel grade-I Shesham wood grade-I.
Front side Finishing with 1mm thick superior quality mica approved make and 0.8mm thick approved shade mica in the inner side. Covering with teak wood beading 25×12mm all the sides of shutter & 35×12mm on outer frame for making good the wall joint including heavy brass S.S. fittings (Handle 200mm 2 Nos., Tower Bolt 150mm 2 Nos., Brass Lock 1 Nos., Magnetic Catcher 2 Nos., Brass Hinges 75×40×2.5 mm 6 Nos., SS Hanger Rod 20mm dia) complete as per drawing and design approved by Engineer in Charge.
Providing & Fixing drawer handle of approved make for drawers with screws complete as per approved
Providing & Fixing drawer lock of approved make for drawers with screws complete as per approved by engineer in charge.
Providing and Fixing T-iron frames for doors, windows and ventilators of mild steel Tee-sections, joints mitred and welded with 15x3 mm lugs 10cm long embedded in cement concrete blocks 15×10×10 cm of 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) or with wooden plugs and screws or rawl plugs and screws or with fixing clips or with bolts and nuts as require including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer.
Powder coating aluminum (minimum thickness of powder coating 50 micron)
Extra for shutters of sliding aluminum windows
Providing and Fixing in position collapsible steel shutters with vertical M.S. Channels 20×10×2mm and bracket with flat iron diagonals 20×5mm size with top and bottom rail of T-iron 40×40×6mm with 40mm dia steel pulleys/ball bearing complete with bolts, nuts locking arrangements inside and outside stoppers, handles etc. as per specification including applying a priming coat of approved steel primer. (To be measured and paid as per outer dimension).
Providing and Fixing 1mm thick M.S. sheet sliding-shutters with frame & diagonals braces of 40×40×6mm. angle iron 3mm M.S. gusset plates at the junction and corners, 25mm dia pulley 40×40×6mm angle and T-iron guide at the top and bottom respectively including applying a priming coat of approved steel primer.
Supplying and Fixing rolling shutters of approved make, made of 80×1.25mm. M.S. laths interlocked together through their entire length and jointed together at the end by end locks mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete including cost of spring hooks, providing and fixing necessary 25.3cm. long wire springs grade No. 2 and M.S. top cover 1.25mm thick for rolling shutters as per design & IS 6248- 1979. (Clear openable area to be measured for payment).
Providing & fixing ball bearing for rolling shutters
Extra for providing mechanical device chain and crank operation for operating rolling shutters. Exceeding 16.80 Sqm in the area.
Fixing standard steel glazed doors, windows and ventilators in walls with 15×3mm lugs 10cm long embedded in cement concrete blocks 15×10×10 cm of 1:3:6 (1 cement: 3 coarse sand: 6 graded stone aggregate 20 mm nominal size) or with wooden plugs and screws or rawl plugs and screws or with fixing clips or with bolts and nuts as required, including fixing of glass panes with glazing clips and special metal-sash putty of approved make, or metal beading with screws (only steel windows with lugs, glass pane cut to size and glazing clips or metal beading with screws, shall be supplied by department free of cost.).
Providing and Fixing steel glazed doors windows and ventilator shutters of standard rolled steel section (IS 1038-1983) joints mitred and welded with steel lugs 13×3mm, 10cm long embedded in cement concrete block 15×10×10cm of 1:3:6 (1cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size) or with wooden plugs and screws or rawl plugs and screws with fixing clips or with bolts and nuts as required including providing and fixing of plain glass panes 4mm thick with cooper glazing clips and special metal sash putty of approved make or metal beading with screws complete including priming coat of approval steel primer, excluding the cost of metal beading and other fitting except necessary hinges of pivots steel handles peg stay etc. as required :
Doors
Windows fixed
Windows side hung /Ventilators top or centre hung (openable)
Partly fixed and partly openable [fixed area not to exceed 33%]
Providing brass handles/peg stays and fittings in place of oxidized fitting
Supplying and Fixing fixed wire gauge of 14 mesh × 24 gauge to the metal frame of rolled section by metal beading 20×3mm with suitable screw at not exceeding 150mm distance.
Supplying and Fixing of chain link fencing with angle iron posts 50×50×6mm placed at every 3 Mtr. apart 30cm in ground embedded in cement concrete 1:3:6 (30×30×45cm) corner and every tenth post to be strutted with (50×50×6cm) angle iron provided and fixed and fitted with posts including earth work in excavation etc. complete with chain link size. 75 mm × 3.15 mm.
Providing and Fixing welded mesh/expanded metal mesh in frame work, flat iron beading 20×3mm including top cross laps inside and out sides welding, iron bolts, crews, clips etc. complete (excluding frame work) of size. Welded mesh 25 mm × 25 mm × 2.1 mm
Expended metal size 20-25 mm size 18SWG
Providing and Fixing of double leaf steel shutter for cupboard, the frame is made of pressed steel ISI section 80 × 25 mm × 1.25 mm thick with 1.00 mm MS sheet to spot welded including holdfasts of 15×3mm, MS oxidized fittings such as butt hinges, sliding doors bolts, handles, tower bolts and twin peg etc complete including applying priming coat of approved steel primer of red oxide zinc chromate and spray painting in approved shade with deco paint of approved quality complete as per direction of Engineer In Charge.
Grading roof for water proofing treatment with water proofing compound. Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size).
Cement mortar 1:3 (1 cement : 3 coarse sand)
Providing gola 75×75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10mm and down gauge) including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design :
Making khurras 450 × 450mm with average minimum thickness 50mm cement concrete 1:2:4 over P.V.C. Sheet 1 Mtr. × 1 Mtr. × 40 micron finished with 12mm cement plaster 1:3 and one coat of neat cement, rounding edges and making and finishing the out let complete.
Providing & Fixing UV stabilised fiberglass reinforced plastic sheet roofing upto any pitch including fixing with polymer coated ‘J’ or ‘L’ hooks, bolts & nuts 8mm dia. G.I plain/bitumen washers complete but excluding the cost of purlins, rafters, trusses etc. The sheets shall be manufactured out of 2400 TEX panel rovigs incorporating minimum 0.3% Ultra-voilet stabiliser in resin system under approximately 2400 psi and hot cured. They shall be of uniform pigmentation and thickness without air pockets and shall conform to IS 10192 and IS 12866.The sheets shall be opaque or translucent, clear or pigmented, textured or smooth as specified. 2.0 mm thick (Wt. 3.3 Kg. / Mtr. Sq.).
Water bound macadam road (average thickness 250 mm)
Providing and Fixing 1st quality MAT finished ceremic tile size 300×300mm confirming to IS : 13755 and IS : 15622 colour such as white, grey, ivory, fume red brown, light green, light blue and other light shades in floors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in the white cement mixed with pigment to match the shade of the tile complete (including the cost of cement mortar bed 1:4).
clips of 10.5mm at 450mm centre to centre shall be fixed in a direction perpendicular to G.I. channel with connecting clips made out of 2.64mm dia × 230mm long G.I. wire at every junction including fixing the gypsum board with ceiling section and perimeter channels 0.5mm thick 27mm high having flanges of 20mm and 30mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450mm centre to centre with 25mm long drive-all screws @ 230mm interval including jointing and fixing to a flush finish of tapered and square edges of the board with recommended filler, jointing tapes, finisher and two coats of primer suitable for board as per manufactures specification and also
Providing and Laying cement concrete including curing, compaction etc. complete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, levelling course etc. up to floor five level excluding the cost of centering and shuttering.
Providing and Fixing 50mm thick cement concrete flooring with Metallic concrete hardener topping, under layer of 38mm thick cement concrete 1:2:4 (1-cement : 2-coarse sand : 4-graded stone aggregate 20mm thick nominal size) and top layer of 12mm thick metallic concrete hardener consisting of mix 1:2 (1 cement : 2 stone aggregate, 6mm nominal size) by volume & mixed with metallic hardening compound of approved quality @ 2Kg./Sqm including cement slurry, rounding off edges etc. but excluding the cost of nosing of step etc. complete.
Chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard jointed with neat cement slurry mixed with pigment to match the shade of tiles including rubbing and cleaning etc. complete on 20 mm thick bed of cement mortar 1:4 (1 cement : 4 coarse sand). Dark shade using ordinary cement.
Add Extra for polished chequered precast cement concrete tiles over item No. 105
Kota stone slab flooring 25 mm thick over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete with base of cement mortar 1:4 (1 cement : 4 coarse sand) For area of each slab from 901 to 2000 Sq. Cm
For area of each slab from 2001 to 5000 Sq.Cm
Kota stone slabs 25 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete. For area of each slab upto 2001 Sq. Cm
Rough Chisel dressed Kota stone 35 mm thick flooring of approved shade set in pattern over 20mm thick base of cement mortar 1:6 (1 cement : 6 coarse sand) and pointing with cement sand mortar 1:3 with pigment to match the shade of stone with joint thickness up to 15 mm complete in all respects :
including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed all complete as per drawing and specification and direction of the Engineer in Charge but excluding the cost of painting.
Fine dressed & machine cut edges 30-35 mm thick sand stone flooring over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) jointed grey cement slurry mixed with pigment to match the shade of stone complete as per design drawing and instruction of EI. Red sand stone
Karauli stone
Mandana stone
Random rubble dry stone Kharanja under floor.
M-35, 60mm thick to be used in light traffic (Light traffic is defined as a daily traffic up to 150 commercial vehicles exceeding 30 KN laden weight, or an equivalent up to 0.5 million standard axles (MSA) for a design life of 20 years (A standard axle is defined as a single axle load of 81.6 KN) like pedestrian plazas, shopping complexes ramps, car parks, office driveways, housing colonies, office complexes, rural roads with low volume traffic, farm houses, beach sites, tourist resorts, local authority footways, residential roads, etc. Category A Denated units to key into each other on four faces zigzag shape as per IRC SP 63 : 2004
Add extra over rates of item No. 11.38, A to C if colored paver blocks are used
25mm thick fine dressed and machine grinded surface stone flooring over 20mm (av.) thick base in cement in CM 1:6 with joints finished flush with: Red sand stone.
Providing and fixing aluminum work for doors, windows, ventilators and partition with extruded built up standard tubular / appropriate Z sections and other sections of approved make conforming to IS :733 and IS :1285, fixed with rawl plugs and screws or with fixing clips ,or with expansion hold fasteners including necessary filling up of gap. at junctions, at top, bottom and sides with required PVC/neoprene felt etc. Aluminium section shall be smooth, rust free, straight, mitered and jointed mechanically wherever required including cleat angle Aluminium snap beading for glazing /paneling, C.P. brass/ stainless steel screws Al. Tower bolt & Al. handle & Al. Aldrop etc.,all complete as per architectural drawings and the directions of Engineer- in – charge. (Glazing and paneling to be paid for separately). For fixed portion
Providing and Applying ACRYLIC emulsion polymer waterproofing chemical coating, on over roof on over roof slabs / terrace / balconies / parapet wall etc. with following method/specification: Paint the surface with regular paint brush so as to obtain approximately 0.3mm thickness coating. apply the 2nd coat next day at right angles to the 1st coat so that total thickness of the coating should be approximately 0.6mm coverage by using above formulation will be 40 ft. 2/litre of chemical painted surface does not require any external water curing since chemical will hold sufficient water for curing. After the primer coat Apply 2 coats of modified acrylic emulsion polymer water proofing compound having solar heat reduction properties coating @ 0.330 KG/SQM on the surface of the interval of 3-4 hours. Undulation on the surface is repair before the waterproofing work.
specification and direction of the Engineer in Charge but excluding the cost of painting of thickness of calcium silicate board as below : 8 mm thick.
Providing & Laying Tactile tile (for vision impaired persons is standard of size 300×300×20mm and confirming to IS 1231 of 1980 (Re affirmed in 2006) in all colours & sheds further product should confirm ASTM 303 for shad resistance and DIN 51099 for colour fastness etc. laid on 20mm thick base of cement mortar 1:4 (1 cement : 4 course sand) in all shapes & patterns including grouting the joint which white cement mixer) will matching pigments etc complete is per direction of Engineer-in-charges. Grade M-30
Plaster on new surface on walls in cement sand mortar 1:6 including racking of joint etc. complete fine finish :
25 mm thick.
20 mm thick.
Finishing with neat cement (punning).
Extra for providing and mixing water proofing material in cement plaster work in proportion recommended by the manufacturers.
Providing and applying white cement based putty over plastered surface to prepare the surface even and smooth complete.
New Plastered Surface (three or more coats).
Old Plastered Surface (two or more coats)
Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete
Pointing on stone masonry in cement sand mortar 1:3 (1 cement : 3 sand) : Flush/ Ruled/ Struck or weathered pointing.
Providing and Fixing Cushion Vinyl/Fully flexible Vinyl Flooring confirming to I.S.-3462 Flooring of approved make with fibre base using rubber base adhesives including rolling with light wooden roller complete : 2.0 mm thick.
igh-density fiber board with a density of 850 Kg/per Mtr. having a click system tongue and groove joint to secure a long lasting joint. The planks are or termite resistant and water protected with both side lamination Wooden flooring Planks of size 1208×194×8 mm / 1215×294×8 mm (8mm thick laminated floor class of use 23/31 having a wear resistance level of AC-3, impact resistance > 9mm, moisture resistance 3-10% as per (EN-424, EN – 438 EN – 425 EN – 417–2) or PREN 3329 complete in all respect as per direction of EI.
Providing and laying wooden flooring with a direct laminated surface treated with aluminum oxide on top of a h
Providing and laying of skirting 89 mm wide having both side laminations with moulding in upper side with matching of floor fixing with nails and screws & fevicol complete in all respect as per direction of EI.
Colour washing of all shades to give an even shade including all scaffolding : Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches by sandla/loi. (only for colour changing).
Old work (one or more coats) including scrapping surface and necessary repairs. (a) Same colour
New work (two or more coats) over and including scrapping and priming coat with cement primer.
Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade including all scaffolding:
Removing dry or oil bound distemper by scrapping sand papering and preparing surface smooth including necessary repairs to scratches by sandla/loi and all scaffolding (for colour changing only)
Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade including all scaffolding:
Two or more coats on new work including preparation of base with primer, putty, lippy etc complete in all respect.
Old work (One or more coats)
Finishing wall with water proofing cement paint of approved brand and manufacture and or required shade to give an even shade including all scaffolding:
New work (Two or more coats applied @ 3.84 kg/10 sqm).
Old work (One or more coats).
Painting exterior surface of Wall with 100% acrylic exterior paint of approved brand and manufacture to give an even shade with two or more coats including preparation of base with sand papering, primer, putty, etc. complete in all respect including scaffolding and safety provision.
New work
Old Work
Applying priming coat :
With ready mix pink or gray primer of approved brand and manufacture on wood work hard and soft wood.
With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/steel works
Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :
With ready mix pink or gray primer of approved brand and manufacture on wood work hard and soft wood.
Two or more coats on new work.
One or more coats on old work.
French sprit polishing :
Two or more coats on new work including a coat of wood filler.
Providing and applying Melamine polish on teak wood work of approved brand and manufacture to give an even shade with two or more coats by compressor including sand papering, wood filler coat etc complete in all respect:
New Surface
Old Surface
Painting (two or more coats) on rain water, soil, waste and vent pipes and fittings with synthetic enamel paint of approved brand and manufacture and required colour over a priming coat of approved steel primer on old work.
Two or more coats on new work including preparation of base with primer, putty, lippy etc complete in all respect.
50 mm dia pipes.
75mm dia Pipes.
Painting with oil type wood preservative of approved brand and manufacture:
New work (Two or more coats).
Face lifting (Doba Wash) with washing of stones by (1:20) acid & water solution, rubbing by brush, washing by clear water, pointing of damaged grooves & doba washing with good quality lime water and painting of doors, windows, ventilators upto all height & lead including all scaffolding and T&P etc. complete as per instructions and direction of Engineer-in-charge.
Making the opening in masonry including dismantling in floor or walls by cutting masonry and making good the damages to walls, flooring and jambs complete to match existing surface including disposal of mulba/ rubbish to the nearest municipal dumping ground. For door / windows / clerestory windows
Renewing glass panes, with putty and nails wherever necessary. Float glass panes of thickness 4 mm.
Renewal of old putty of glass panes (length)
Refixing old glass panes with putty and nails
Providing and fixing 16 mm M.S. Fan clamps of standard shape and size in existing R.C.C. slab including cutting chase and making good and painting exposed portion of the clamps complete.
Repair to stone masonry in cement sand mortar 1:6 with old and new stone.
Repair to brick masonry in cement sand mortar 1:6 with new brick.
Patch repair to cement concrete floor including digging out old floor in regular shape and removal of rubbish curing etc. complete in all respects.
Making holes in stone masonry wall upto 450 mm × 450 mm size and making good in CM 1:6.
Grinding of existing floor with : 60, 80, 120 and 360 No. Carborundum stone including cost of wax polishing complete.
Providing and fixing double scaffolding system on the exterior side, upto five story made with 4" wooden member 1.5 m c/c horizontal and vertical direction joining with rassi, clamps, challies. The scaffolding system shall be stiffened with bracing, runner, connection of building if necessary with all essential safety features for the workmen etc complete as per direction of EI. The lavation area of the scaffolding shall be measured for payment. The payment will be made once irrespective of duration of scaffolding. Note : This item to be used for maintenance work judicially
Repair of existing steel glazed doors, windows and ventilator, MS sheet door, gage doors, compound wall gates etc. by welding drilling complete include. Cost of welding rods and hire charge of welding machine and TP etc complete.
Labour charges for repair to door / window without using any material such as applying randha (finishing) tightening of bolts & screw etc.
L/C for fixing of GI/AC sheet include. Cutting jhiri and repair, cutting of sheet, fixing of sheet with J or L hook and bitumen washer as per direction of EI
Repair of rolling shutter with replacement of shutter spring incl. removal of old spring in the existing rolling shutter incld. Cost of new spring
Repair of rolling shutter with using any material such as bend repair, tightening of spring, bolt and screw etc. complete
Re-fabrication work with existing steel work including cutting, welding & re-fabrication as per requirement with fixing at site complete as per direction of Engineer In charge
Repair to damaged RCC slabs, beams & columns etc. for strengthening with cement mortar 1:2 in following steps : (i) Choping losse & cracked concrete to required depth, cleaning the exposed surface of steel & concrete with wire brush & sand papering, cleaning of concrete surface with water as necessary & getting dried. (ii) Applying Epoxy primer on the exposed steel bars. (iii) Applying Epoxy hardener & resin mix (as per manufactured's specification) on concrete & steel bars with brush. (iv) Spreading dry cement mortar 1:2 mix over epoxy treated wet surface & allow it to dry for one day. (v) Plastering the surface with cement sand mortar 1:3 upto depth of 30mm complete. (vi) Cure the plastered surface for 15 days, all work including scaffolding etc. complete in all respect.
Repair of door, window shutters including cost of material and labour for change of damaged :
Style / rail of teak wood 30mm thick/ Aluminium Section (4" wide)
Style / rail of teak wood 30mm thick/ Aluminium Section (6" wide)
Panel by (Shuttering Ply - 9mm thick (Commercial))
Panel by (Wire Gauge 14 mesh × 24 gauge)
Aldrop of mild Steel (12" long × 12mm dia)
Aldrop of mild Steel (8" long × 10mm dia)
Stopper of Aluminium with (Single Rubber Gutka)
Stopper of Aluminium with (Double Rubber Gutka)
Door Springs of mild Steel
Steel Hinges (For Wooden Chowkhat, 3" size)
Steel Hinges (For Wooden Chowkhat, 4" size)
Steel Hinges (For Stone Chowkhat, 4"size)
Mild Steel Tower Bolt 6" long
Steel Locking Bolt
Steel Handle 6" size
Making of hole in R.C.C. slab/wall/beams and masonry wall (width up to 450 mm) by core cutting machine complete as per direction of EI. From diameter 100 mm to 150 mm
Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer-in-charge. 1:3:6 or richer mix.
Demolishing R.B. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge.
Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. In cement mortar.
Demolishing stone rubble masonry manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge : In cement mortar.
Dismantling doors, windows and clearstory windows steel or wood shutter including chowkhats and holdfasts etc. complete and stacking within 50 meters lead :
Of area 3 square meter and below.
Of area exceeding 3 square meter.
Taking out doors, windows and clearstory windows shutters (steel or wood) including stacking within 50 meters lead:
Of area 3 square meter and below.
Of area exceeding 3 square meter.
Providing and Fixing fully panelled/partly paneled / double leaf shutter frame for doors as per approved design and drawings with approved ordinary C.P. / oxidised steel fittings as per Annexure - 'A' and width of styles & top rails of 100mm and lock rails width of 150mm and bottom rails of 200mm width including teak wood beading of size 19mm × 12mm on both faces complete : 35 mm thick - Shesham wood grade-I
P & F 1st quality Heavy Duty Vitrified Double Charged tiles on floor, skirting and steps etc. in different sizes (thickness minimum 10mm) with water absortion less than or equal 0.08% and conforming to IS 15622 of approved make in all colour and shade, laid with 20 mm thick CM 1:4 including grounting the joints with white cement and matching pigment etc complete. Size 600 mm × 600 mm
P & F 1st quality Heavy Duty Vitrified glazed MAT tiles on floor, skirting and steps etc. in different sizes (thickness minimum 10mm) with water absortion less than or equal 0.08% and conforming to IS:15622 of approved make in all colour and shade, laid with 20 mm thick CM 1:4 including grounting the joints with white cement and matching pigment etc complete. Size 600 mm × 600 mm
Providing & Fixing telescopic channel of approved make for drawers with screws complete as per approved by engineer in charge. 450 mm long.
Providing & Fixing BWR ISI marked 19 mm board of approved make for making wardrobe/shelves and other furniture with fevicol & nails complete as per approved by engineer in charge.
Dismantling steel work in single sections including dismembering and stacking within 50 meters lead in: Channels, angles, tees & flats.
Dismantling steel work in built up sections in angles, tees, flats and channels including all gusset plates, bolts, nuts, cutting rivets, welding etc. including dismembering and stacking within 50metres lead.
Dismantling steel work manually/ by mechanical means in built up sections without dismembering and stacking within 50 metres lead as per direction of Engineer-in-charge.
Extra for dismantling trusses, rafters, purlins etc. of steel work for every additional span of one metre or part thereof beyond 10 metres
Extra for dismantling trusses, rafters, purlins etc. of steel work for every additional height of one metre or part thereof beyond 5 metres.
Extra for making of structural steel work required to be re-erected.
Dismantling tile work in floors and roofs laid in cement mortar including stacking of serviceable material and disposal of unserviceable material within 50 meter lead: For thickness of tiles 10 mm to 25 mm.
Dismantling stone slab/ terrazo chip flooring laid in cement mortar including stacking of serviceable material and disposal of unserviceable material within 50 meters lead.
Dismantling brick tiles covering in terracing including stacking of serviceable material and disposal of unserviceable material within 50 meters lead.
Dismantling roofing including ridges, hips, valleys and rafters etc. and stacking the within 50 meter lead of: Asbestos Sheet.
Dismantling barbed wire or chain link fencing including bending making rolls and stacking within 50-meter lead.
Dismantling CI or asbestos rain water pipe with fitting and clamps including stacking within 50 meter lead:
Up to 80 mm dia pipe.
100mm dia pipe.
Dismantling tar felt over roofing complete including stacking of serviceable material and disposal of unserviceable material within 50-meter lead.
Dismantling GI pipes (external work) including excavation and refilling trenches after taking out the pipes and including stacking of pipes within 50 meter lead: 15 mm to 40 mm nominal bore.
Above 40mm nominal bore.
Dismantling CI pipes including excavation and refilling trenches after taking out the pipes, breaking lead caulked joints, melting of lead and making into block, including stacking of pipes lead at site within 50 meter, of dia: Up to 150 mm dia.
Above 150mm dia. up to 300mm dia.
Dismantling asbestos cement pressure pipes including excavation and refilling trenches after taking out the pipes, and stacking the same within a lead of 50 meter, of dia:
UP to 150 mm.
Above 150mm.
Dismantling of gully chamber of various sizes including CI grating with frame including stacking of useful materials near the site and disposal of unserviceable material within 50 meter lead including refilling the gap.
Dismantling of flushing cistern of any size including stacking of useful materials near the site and disposal of unserviceable material within 50 meter lead.
Dismantling of CI sluice valve including stacking of useful materials within a lead of 50 meter: Up to 150 mm dia.
Dismantling old plaster or skirting, raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 meter lead.
Dismantling CC jali including cost of making grooves in plaster and making good and including disposal of unserviceable surplus material and stacking of serviceable material with in 50 meters lead as directed by Engineer-in-charge.
Removing aluminium/Gypsum partitions, doors, windows, fixed glazing and false ceiling including disposal of unserviceable material and stacking of serviceable material with in 50 meters lead as directed by Engineer-in-charge.
Making of hole (width up to 150 mm) in R.C.C. slab/wall/beams by power driven drilling machine complete as per direction of EI :
upto 150 mm thick.
Extra if square, rectangular hollow tubular sections are used or grill made by flats only
Providing and Fixing cow catcher made of R.S. joist angles channels MS rounds including cutting welding and fabrication with priming coat of red oxide (as per design).
Supplying and providing of two components poly sulphide sealant containing solid contents, confirming to standard specification and approved compatible primer, for priming vertical faces prior to application of poly sulphide sealant including all labour charges for sealing of expansion joints after drill mixing of two components sealing compound. Cleaning and preparation of expansion joint using wire brush sand papering with emery paper and filing with suitable mechanical means. The work includes racking and cleaning of joints, sticking, debonding tape on bottom of joint, applying primer on edges, using masking tape on edges, providing of sealant and removal of masking tape immediately after providing sealant in joint.
To vertical joint between RCC columns, bricks & stone masonry in size 40 mm width and 12 mm depth, including providing back up material (Thermocol foam) if required.
Providing and fixing 150 mm wide sheet covering over expansion joints with iron screws as per design to match the colour / shade of wall treatment. Aluminum fluted strips 2 mm thick.
Providing and Fixing calcium silicate board false ceiling at all heights including providing and fixing of frame work made of special sections power pressed from M.S. sheet and galvanised in accordance with zinc coating of grade 350 as per IS : 277 and consisting of angle cleats of size 25mm wide × 1.6mm thick with flanges of 22mm and 37mm at 1200mm centre to centre one flange fixed to the ceiling with dash fastener 12.5mm dia × 40mm long with 6mm dia bolts to the angle hangers of 25×25×0.55mm of required length, and other end of angle hanger being fixed with nut and bolts to G.I. channels 45×15×0.9mm running at the rate of 1200mm centre to centre to which the ceiling section 0.5mm thick bottom wedge of 80mm with tapered flanges of 26mm each having clips of 10.5mm at 450mm centre to centre shall be fixed in a direction
perpendicular to G.I. channel with connecting clips made out of 2.64mm dia × 230mm long G.I. wire at every junction including fixing the calcium silicate board with ceiling section and perimeter channels 0.5mm thick 27mm high having flanges of 20mm and 30mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450mm centre to centre with 25mm long drive-all screws @ 230mm interval including jointing and fixing to a flush finish of tapered and square edges of the board with recommended filler, jointing tapes, finisher and two coats of primer suitable for board as per manufactures specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed all complete as per drawing and
Providing and filling in position bitumen sealing compound grade-A (IS:1834) in expansion joints.
Providing and filling in position bitumen mix filler of proportion 80 Kg. of hot bitumen, 1 Kg. of cement and 0.25 cubic meter of coarse sand for expansion joints.
Anodised aluminum (anodised transparent 81 dyed to required shade according to IS : 1868. (Minimum anodic coating of grade AC 15, Anodizing to be got done from approved Anodizer)
Providing and filling in position bitumen sealing compound grade-A (IS:1834) in expansion joints.
Powder coating aluminum (minimum thickness of powder coating 50 micron)
For shutters builtup standard tubular sections of openable doors, windows & ventilators including providing & fixing hinges / rollers etc. and making provision for fixing of fittings wherever required (lockers shall be paid for separately).
Providing and fixing 12 mm thick prelaminated three layer medium density (exterior grade) particle board Grade I, Type II conforming to IS : 12823 bonded formaldehyde synthetic resin ,of approved brand and manufacture in paneling fixed in aluminium doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and direction of engineer-in-charge. Pre-laminated particle board with decorative lamination on one side and balancing lamination on other side.
Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with PVS / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge. (Cost of aluminium snap beading shall be paid in basic item) With float glass panes of 5.0 mm thickness (weight not less than 13.50 kg/sqm)
Providing and Fixing double action hydraulic floor spring of approved brand and manufacture IS : 6315 marked, for doors including cost of cutting floors as required, embedding in floors and cover plates with brass pivot and single piece M.S. With stainless steel cover plate.
Filling the gap upto 5 mm depth and 5 mm width in between aluminium frame & adjacent RCC/ Brick/ Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete.
Providing and fixing 100mm brass locks (best make of approved quality) for aluminium doors including necessary cutting and making good etc. complete.
Providing and fixing aluminium U shape handle of size 100mm with SS screws etc. Complete as per direction of Engineer-in-charge.
Anodized (AC 15) aluminium.
Powder coated minimum thickness 50 micron aluminium
S&F fixed wire gauge of stainless steel of 14 mesh × 24 gauge to the aluminium window by Aluminium beading 20×3mm with suitable screws not exceeding 150mm distance at all heights with all lead and lift with scafolding.
P&F vertical Blinds, headrail shall be oriented aluminum alloy 50 mm wide × 18 mm high the thickness shall be 1.2 mm control unit shall be made of high grade polymer and shall be housed in side the headrail, which shall transfer motion from chain tilter to tilt rod. Chain tilter shall be made of plastic bead of diameter 4.5 mm through which 2 mm thick polyester code passes. Tilt rod shall be extruded aluminum having 3 key ways. Runner shall be moulded plastic & shall have to plastic wheels mounted on plastic axles to enable runner to slide unhindered in headrail. Luver shall be made of fabric 100 mm colour fast & shall have protective scotchgard coating to resist stains & dust. Bottom mechanism consist bottom weight made of powder coated galvanized steel for maximum corrosion resistance. The bottom weight shall be attached with bottom.
Providing and Fixing sun control film, thickness of film 1 Mil Visible Light Transmittance 4-24% & Solar Energy Transmittance 42-51% & Total solar Energy rejection 37-43%of approved colour and shade, complete in all respect, at all level, as directed by engineer-in-charge.
Providing and Fixing of wall paneling on grid made out of PVC profile section of size 21×17mm with a wall thickness of 1.5mm+/-0.2mm, fixed on the existing wall with wood screw of size 50mm X 8mm with rowel plug at a spacing of 900mm center. uPVC profile section of size 150mm × 10mm with a wall thickness of 1.0mm+/-0.2mm to be fixed on the grid by self tapping screw of size 19mm × 6mm.Necessary cutouts for electrical connection to be provided at required places. The edge and periphery, finally to be covered by extruded PVC beading section of size 28mm × 12mm with a wall thickness of 1.0mm+/-0.2mm complete as per manufacture’s specification and direction of Engineer-in-charge.
Providing and Fixing expanded grill made of aluminum as per design and drawing having members section of size 7.5mm × 6.0mm and opening of size 50mm×48mm to aluminum window/vent with required screws, Y and H aluminium section (as per drawing) at the ends and middle joints respectively complete in all respect as per direction of engineer in charge.
Providing and filling in position bitumen sealing compound grade-A (IS:1834) in expansion joints.
Powder coating aluminum (minimum thickness of powder coating 50 micron)
Providing and Fixing Aluminium composite panel of approved make 3mm thick with 0.5mm thick skin & PVDF coated approved shade for wall panelling. Main framing work to be done using 50mm×25mm×1.6mm tubular section of approved make. Stainless steel screw to be used to fix the ACP panel to be fixed to the main frame with industrial adhesive tape and panel groove to be sealed with weather proof silicon sealant suitable for glass/aluminium etc. complete in all respect as approved by Engineer-in-charge.
P/F wall mounted inverted L-Shaped grab bar with 700mm long bar as approved design, made of 35mm stainless steel pipe having anti-bacterial Nylon surface with contour finish for better grip. Grab bar should be mounted on wall at height of 700mm from the finish floor level complete in all respect as per Harmonized guideline & Satisfaction of Engineer-in-Charge. Cera make (B2210103)
Supplying and fixing Rollor Blinds of good quality and approved make made out of Imported fabric including Roller Mechanism and lock with chain system with all necessary hooks etc. complete as per direction and sample approved by engineer-in-charge.
Providing & Fixing Aluminium composite panel of indo bond/euro/flexi bond of equivalent made 3mm that with 0.5mm thick skin& PVDF coated of approved shads for toilet door in double layer in Aluminium frame complete in all respect as per sample approved by Engineer in Charges.
Providing & Fixing brass handle 125mm with plate 175×22mm with screw complete in all respect as per direction of Engineer in charges.
Labour Charges for removing and refixing Aluminium Partitions door including minor repair on alteration in the same.
Providing and fixing thermal insulation with Resin Bonded rock wool conforming to IS:8183, having density 48 kg/m3, 50 mm thick, fixed on the roof top with screws, rawel plug & washers and held and in position by criss crossing GI wire etc. complete as per directions of Engineer-in-charge.
P/F wall mounted 600mm long grab bar as approved design, made of 35mm stainless steel pipe having anti-bacterial Nylon surface with contour finish for better grip. Grab bar should be mounted on wall at height of 800mm from the finish floor level complete in all respect as per Harmonized guideline & Satisfaction of Engineer-in Charges. Make Cera (B2210106)
Supply and fixing of solid stainless steel grade 304 C type door handle of dia 32mm length 600 (outside measurement) having hole dia 14 mm of with i/c key arrangement.
Providing and applying treatment of plaster and masonry cracks with pre-mixed, ready to use, geo polymer based mortar & confirming to ASTM C 1600 upto 15 mm width and 15 mm depth by making V-Groove with following property – (i) Curing Free, compressive strength of 15 MPa within 2 hours, Quick Setting and with bond strength of 4 MPa within 24 hours with all scaffolding. Note : (This item is to be used in only emergency situation after decided by Engineer in charge)
m each having
Providing and Fixing 12.5 mm thick tapered edge gypsum board conforming to IS 2095-Part I at all height false ceiling including providing and fixing of frame work made of special sections power pressed from M.S. sheet and galvanised in accordance with zinc coating of grade 350 as per IS : 277 and consisting of angle cleats of size 25mm wide × 1.6mm thick with flanges of 22mm and 37mm at 1200mm centre to centre one flange fixed to the ceiling with dash fastener 12.5mm diax40mm long with 6mm dia bolts to the angle hangers of 25×25×0.55mm of required length, and other end of angle hanger being fixed with nut and bolts to G.I. channels 45×15×0.9mm running at the rate of 1200mm centre to centre to which the ceiling section 0.5mm thick bottom wedge of 80mm with tapered flanges of 26m
per cm depth per cm witdth for 100 mtr. Length
per cm width per cm depth per 100 mtr. length
Providing and Laying Water Proofing Treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : (i) first layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @0.253 kg//sqm. This layer will be allowed to air cure for 4 hours. (ii) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed by water curing for 48 hours. The rates includes preparation of surface treatment & sealing of all joints, corners, junction with polymer mixed slurry.
Bituminous Road (average thickness 300 mm)
stage.html
html • 0.03 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Tendernotice_1.pdf
PDF • 0.23 MB
BOQ_929890.xls
BOQ • 0.66 MB
TenderDocument.pdf
Tender Documents • 1.19 MB
Download all tender documents and submit your bid