Special repair/rewiring to Bldg No. NP-01, TS-22, Hangers and other connected Bldgs related with flying operation at Army Aviation Squadron under GE Nagrota.

Amount

Schedule 'A' Part-I (Internal Electrification)

Taking down carefully aluminium conductor point wiring (light fan, socket and power) complete with fittings such as switches, sockets, lamps holder, utility light fitting, fan regulator etc and making good disturbed surface of walls and floors etc. and keeping in safe custody for taking credit, complete all as specified and directed by Engr-in-Charge.

Taking down ceiling fan any sweep, removing blades, cleaning the fan completly for dust and dirt and hanging the same back to its original position including connecting the 3 core flexible copper wire to ceiing rose etc after the completion the point wiring including replacement old unservicable fan hook, rubber pad, nut bolts and washers etc, complete all as specified and directed by Engineer in charge.

M&L for point wiring with PVC insulated unsheathed 1100 volt grade FRLS cable with multi stranded copper conductor of size 1.5 Sq mm (Nominal area) drawn through and including non metallic rigid PVC conduit medium grade ISI marked not less than 20mm dia ,concealed in wall and surface on ceiling with all conduit fittings & fixing acessories inculding sunken anodised pressed steel terminal box not less than 1.2mm thick covered with 3 mm thick plastic laminated sheet cover of suitable size with brass screws for mounting switches, sockets, regulators with and including 1.5sqmm FRLS multi stranded copper conductor drawing as continuous earth wire connected to main earth and earth dolly, complete all as specified and directed for the following:-

(a) One light point controlled by one switch 5 Amp.

(b) One ceiling fan/exhaust fan point controlled by one switch 5Amp

(c) One socket outlet 5Amp controlled by one switch on same board.

(d) One socket outlet 5 Amp controlled by one switch on independent board.

All as per item No 1.03 here in before but point wiring with 2.5sqmm FRLS multi stranded copper conductor cable for main circuit and 2.5sqmm cable as earth continuity conductor for one 15 Amp socket out let controlled by one 15 Amp switch on independat board.

S&F switch piano flush type 5 Amps single pole one way, complete all as specified and directed.

S&F switch socket combination 2 in 1, 3 pin, 5 Amp flush type, complete all as specified and directed.

S&F switch socket combination 2 in 1 5 pin 5 /15 Amps flush type, complete all as specified and directed.

S&F of ceiling rose 3 terminal PVC/Polycarbonate isolated body, complete all as specified and directed.

S&F stepped type electronic fan regulator flush type on the existing phenolic laminated sheet etc as required, complete all as specified and directed.

S & F Integrel sleek extruded batten aluminium /CRCA channel fitting with LED 18 watt complete with all accessories and including connecting up with three core twisted flexible copper conductor cable with suitable size of 230V, 50 Hz, Cat part No. BLRB DB 118 ( for batten fitting) & Cat part no. BLRB18W CW LED (for LED 18 watt ) of Bajaj or equivalent in approved make, complete all as specified and directed.

S & F batten integrated LED channel of 5W, 230 V frequency 50/60 Hz integral sleek extruded polycarbonate LED channel with white acrylic cover, power factor not less than 0.9 as per Cat No BCLSB 05 WH of Bajaj or equivalent in approved make, complete all as specified and directed.

S & F decorative wall mounted luminair with & including 9 watt LED lamp complete as per Cat No LHFHCHE1TL1W020 of Havells or equivalent in approved make, complete all as specified and directed.

S & F white powder coated CRCA housing with LEDs 36 W, 230 V, 50 Hz recess mounting LED 2 feet x 2 feet luminaries, samless front frame with flat white hight transmission acrylic cover complete with all accessories including connecting up with twin core twisted flexible copper conductor cable with suitable size. Cat Part No BZRSQL 36 W GZ WH of Bajaj or equivalant in approved make, complete all as specified and directed.

S & F 80W LED Floodlight luminair with secondary optics made in pressure die cast housing and heat sink in aluminium extrusion with IP66 of cat part No BJFL80W LED of Bajaj or equivalent in approved make, complete all as specified and directed.

S & F LED light fitting 1x9W bulk head luminaries IP 65 complete with all accessories including LED lamp 10 watt , connecting up with twin core twisted flexible copper conductor cable with suitable size of 230V 50 Hz, complete all as specified and directed.

S&F lamp holder PVC/polycarbonate type with back plate suitable for batten fittings complete all as specified and directed.

S & F LED bulb 7 watt complete all as specified and directed.

S&F in rpeiar sheet metal enclosure distribution board SPN 12 way 230 V, 50 Hz double door with neutral, Earthing bar and din rail, complete all as specified and directed.

S&F in repair sheet metal enclosure distribution board SPN 8 way 230 V, 50 Hz double door with neutral, Earthing bar and din rail complete all as specified and directed.

S & F in repair Sheet metal enclosure double door for distribution board factory made for MCB DB load link TPN 4 way suitable for MCCB as incomer, 125 Amp,4 pole. (when MCB's are to be used) with suitable size of busbar complete,fixed flush in wall including chases wall for fixing DB and making good the distributed wall surfaces to match with existing specification, complete all as specified and directed.

S & F MCB SPN 32/40 Amps, 10 KA, 230 volts 'C' series, complete all as specified and directed.

S & F MCB single pole 6 to 30 Amps, 10KA, 230 volts 'C' series, complete all as specified and directed.

S & F MCB single pole 40 Amps, 10KA, 230 volts 'C' series, complete all as specified and directed.

S & F MCCB 63 Amp, 4 Pole, 16 KA ,415 volts, with fixed magnetic and fixed thermal setting, complete all as specified and directed.

S & F MCCB 125 Amp, 4 Pole, 16 KA, 415 volts, with fixed magnetic and fixed thermal setting, complete all as specified and directed.

S & F sheet metal enclosure single pole and neutral with a two pin and earth plug and socket complete with one single pole MCB SP 32/40 Amps, complete all as specified and directed.

S & F sheet metal enclosure single pole and neutral with a two pin and earth plug and socket complete with one single pole MCB SP 40/63 Amps, complete all as specified and directed.

S&F sub main wiring with two single core FRLS PVC insulated unsheathed 1100 volts grade cable with stranded copper conductor of size 4 Sqmm drawing through and including concealed rigid non metallic PVC conduit medium grade ISI marked 20 mm dia including one single core FRLS PVC insulated unsheathed 1100 volts grade cable with stranded copper conductor of size 4 sqmm as earth continuity conductor connected to common earth and earth dolly complete all as specified and directed.

S&F sub main wiring with two single core FRLS PVC insulated unsheathed 1100 volts grade cable with stranded copper conductor of size 10 Sqmm drawing through and including concealed rigid non metallic PVC conduit medium grade ISI marked 25 mm dia including one single core FRLS PVC insulated unsheathed 1100 volts grade cable with stranded copper conductor of size 10 sqmm as earth continuity conductor connected to common earth and earth dolly, complete all as specified and directed.

Supply and laying or fixing including removing of existing cable 1100 volts grade cable PVC insulated aluminium conductor un-armoured of 16 Sqmm 2 core flat or circular, served with inner sheathing of pace tape and overall PVC sheathed in service connection suspended by insulated hangers not more than one Mtr apart including 4 mm dia suspension GI wire, complete all as specified and as directed by Engr-in-Charge.

Supply and fixing Exhaust fan 300 mm sweep single phase AC 230/240V complete with louvers for wall mounting including grouting, holding down bolts, nuts, washers and provision of flexible copper conductor cable 3 core 23/0.0076 size from ceiling rose to exhaust fan including cutting of the hole, complete all as specified and directed.

M&L for earthing complete for bldg with galvanized mild steel earth plate electrode 60cm x 60cm x 6mm thick buried directly in ground (earth pit not less than 2.25 meters below ground level) with top edge of earth plate not less than 1.5 meters below ground level connected to galvanized earth wire 4.00 mm dia by means of nuts, bolts, thimbles, chuck nuts, washers of GI or steel, PCC (concrete chamber of size 300 mm x 300 mm x 300 mm inside dimension) shall be PCC 1:3:6 type C-1 using 20mm graded stone aggregate with fair finish , internal surface of concrete chamber shall be given 15mm thick plaster in CM 1:4, funnel with wire mesh of 22 gauge, 80 mm thick PCC pit cover 320 mm x 320 mm of RCC 1:2:4 type B-1 using 20 mm graded stone aggregate reinforced with XPM, JALLI pit shall be filled with charcoal dust and common salt all as shown in electrical plate No 3 of MES SSR Part-I (2009) as specified including provision of 15mm dia medium grade GI pipe for earth wire protection and 20 mm dia for watering complete , all excavation and earth work & connecting the earthing to an earthing test point / main switch board as specified and testing on completion, complete all as specified and directed.

Schedule 'A' Part-II (External Electrification)

Excavation in trenches in any type of soil not exc 1.5m wide and n.exc 1.5m in depth for electric poles stay foundation and under ground electric power cables and getting out, complete all as specified and directed.

Returning, filling in. including spreading, leveling, watering and well ramming in layers not exceeding 25cm thick in any type of soil, complete all as specified and directed.

Removing excavated surplus material to a distance not exc 50m and depositing where directed at a level not exceeding 1.5m above the starting point, complete all as specified and directed.

Supply,laying and spreading in layers dry clean river sand for cable cushioning with a layer of sand 8 cm depth before laying & 15 cm depth after laying the cable punned down to a depth of 10 cm above the top of the cable, complete all as specified and directed.

Brick covering with width equal to length of brick as mechanical protection to cables with well burnt sub class ‘B’ (old size) bricks laid dry flat, complete all as specified and directed.

Supply, laying, jointing and testing XLPE insulated PVC sheathed armoured under ground cable heavy duty with aluminium conductor LT 1100 V grade cross sectional area 120 Sqmm 3.5 core, complete all as specified and directed by Engineer-in-Charge.

Supply, laying, jointing and testing XLPE insulated PVC sheathed armoured under ground cable heavy duty with aluminium conductor LT 1100 V grade cross sectional area 95 Sqmm 3.5 core, complete all as specified and directed by Engineer-in-Charge.

Supply, laying, jointing and testing XLPE insulated PVC sheathed armoured under ground cable heavy duty with aluminium conductor LT 1100 V grade cross sectional area 70 Sqmm 3.5 core, complete all as specified and directed by Engineer-in-Charge.

Supply, laying, jointing and testing XLPE insulated PVC sheathed armoured under ground cable heavy duty with aluminium conductor LT 1100 V grade cross sectional area 50 Sqmm 3.5 core, complete all as specified and directed by Engineer-in-Charge.

Supply, laying, jointing and testing XLPE insulated PVC sheathed armoured under ground cable heavy duty with aluminium conductor LT 1100 V grade cross sectional area 35 Sqmm 3.5 core, complete all as specified and directed by Engineer-in-Charge.

Supply, laying, jointing and testing XLPE insulated PVC sheathed armoured under ground cable heavy duty with aluminium conductor LT 1100 V grade cross sectional area 16 Sqmm 4 core, complete all as specified and directed by Engineer-in-Charge.

Supply, laying, jointing and testing XLPE insulated PVC sheathed armoured under ground cable heavy duty with aluminium conductor LT 1100 V grade cross sectional area 16 Sqmm 2 core, complete all as specified and directed by Engineer-in-Charge.

supply and fixing of Wall Mounted Bus Bar of Capacity 200 Amp Duly fixed on wall with nuts bolts washers, complete all as specified and directed.

Feeder piller box out door type ‘factory made’ made out from 16 SWG MS sheet supported with legs of 45cm long made of iron angle 25x25x4mm thick of size 75cm x60cm x45 cm with 04 Nos aluminium bus bar of 200 Amps mounted on porcelain insulator duly drilled hole for cable connection including front and rear side opening with locking arrangement provn for incoming and outgoing cables with glands including painting with two coat of smoke grey synthetic enamel paint over a coats of red oxide primer, complete all as specified and directed by Engineer-in-Charge Note:- Feeder pillar box shall be mounted on brickwork in CM 1:4 not less than 30 cm above ground level with suitable foundation, rendering 15 mm in CM 1:6 and two coats of cement base paint and the rates shall be inclusive in the quoted rate.

Supply and Fixing in Replacement of Garden Light of Capacity 10 W IP 65 Rated LED Bollard with robust design and efficient light distribution , Make CG Cat Part No LBLSR-10-CDL or equivalent in approved make, complete all as specified and directed.

Supply and fixing Junction box made of mild steel 1.6 mm thick of size 150 mm x 100 x 75 mm including 02 Nos aluminium bus bar of 3 mm thick duly fitted on suitable insulator with fixing arrangement and including , PVC pipe of suitable size from junction box to light fitting properly clamped with pole/fixed on wall and including taking out old unserviceable boxes complete all as specified and directed by the Engineer-In-Charge.

Supply and Fixing in replacement of GATE Light of capacity 20 W , IP 65 rated Led Post Top ideal to lit up parks , garden ways and heritage sites complete including wiring , fitting and fixtures complete. Make CG Cate Part No LPTH -20-WW or equivalent in approved make, complete all as specified and directed.

M&L for earthing complete for bldg with galvanized mild steel earth plate electrode 60cm x 60cm x 6mm thick buried directly in ground (earth pit not less than 2.25 meters below ground level) with top edge of earth plate not less than 1.5 meters below ground level connected to galvanized earth strip 25x4.00 mm by means of nuts, bolts, thimbles, chuck nuts, washers of GI or steel, PCC (concrete chamber of size 300 mm x 300 mm x 300 mm inside dimension) shall be PCC 1:3:6 type C-1 using 20mm graded stone aggregate with fair finish , internal surface of concrete chamber shall be given 15mm thick plaster in CM 1:4, funnel with wire mesh of 22 gauge, 80 mm thick PCC pit cover 320 mm x 320 mm of RCC 1:2:4 type B-1 using 20 mm graded stone aggregate reinforced with XPM, JALLI pit shall be filled with charcoal dust and common salt all as shown in electrical plate No 5 of MES SSR Part-I (2009) as specified including provision of 15mm dia medium grade GI pipe for earth wire protection and 20 mm dia for watering complete , all excavation and earth work & connecting the earthing to an earthing test point / main switch board as specified and testing on completion, complete all as specified and directed.

Deduction to be made from BOQ for schedule of credit (Sch 'A' Part - III) Amount of Rs. 51157.00 during AOC Note:- Tenderers shall not quote for this Schedule

Kalsi Engineers and contractors

Nitika electricals and engineers works

U K Engineering Works

M/S Shankardass Devidass

VIJAY BUILDERS

ASHOKA ENGINEERS AND BUILDERS