REPAIR TO FLOORING JOINERY PLASTER PLUMBING AND SANITARY WORKS AT NEW NAVY NAGAR UNDER AGE BR I OF GE NW NAVY NAGAR COLABA MUMBAI

Amount

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises

S & F Non Skid ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) size 300x 300 mm area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15 mm thick screed bedding layer in CM 1:4 complete all as specified

S&F Glazed colour ceramic tiles in vertical surfaces 300 x 200x 7 mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match including 10 mm thick redering as backing layer in CM 1:4 complete all as specified.

S & F Non Skid rectified ceramic floor tiles 8 to 9 mm thick of size 600x 600 mm as in floors etc approved colour pointed in white or coloured cement to match and including 15 mm thick cement screed base (1:6) laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete (Note : (i) The rate includes the cost of cement screed bed

Taking down cement plaster of any description including racking out joints, hacking for key scrubbing down with water & removed debrises out MD land.

M&L rendering 15mm thick in CM (1:6) on wall finished even and fair without using extra cement as in patches all as specified and directed by Engr -in- Charge.

M&L for preparing newly plastered surfaces of wall with wall care putty and applying two coats of oil emulsion distemper over a coat of primer all as specified and as directed

Demolition of cement Concrete unreinforced in ground floors and pavings n exc 15 cm thickness (below or above ground level)

M&L 40 mm thick PCC 1:2:4 type B-1 using 20mm graded aggregate as in flooring, finished even and smooth with using extra cement.

S&F 125 mm extruded aluminium handles, fabricated type anodised fixed in repairs.

S&F 150mm aluminium anodised barrel tower bolts of extruded section fixed in repairs.

S&F 100mm aluminium anodised barrel tower bolts of extruded section fixed in repairs.

S&F in repairs 300 mm long aluminium alloy, anodised sliding door bolt with hasp and staple ( bolt type ) and fixing bolt and sliding bolts of extruded section or cast aluminium alloy.

Taking down chawkhats or frame (w/o taking off shutters from the frames) n.exc 1.50 Sqm complete all as specified .

S & F Factory made solid panel pvc door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing.

S & F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, fixing in opening as per specification

Cutting holes in brick walls but in brick walls built in cement mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement lime mortar in cm 1:2;4 type B-1 not exceeding half brick as required depth of embedded portion of holdfasts

M & L MS works in holdfast made of fe -290 of length

S & F Aluminium, anodised, barrel tower bolts of extruded section and fixed 100 mm length.

S & F Aluminium handles, cast type, anodised of length 100 mm

S & F in SS butt hinges 100 mm size

Taking down shutters of any description exc 2.00 sqm each complete all as specified.

S & F 30 mm thick flush shutters, solid core construction, with particle board core complete all as specified.

Suppling and fixing 2nd class hardwood 35mm thick skelton shutters, open rebated and prepared to receive wire mesh edge of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing mesh etc, sizes of members of shutters as specified in SSR complete all as specified and directed by Engg-In- Charge.

Supply and fixing Marine ply 18mm thick as in cupboard shutter including fixed with piano hinges complete all as specified and directed by Engg-In- Charge.

M&L for welded mesh n.exc 4kg/ Sqm including beading, fillets, nails including dismantling old unserviceable mesh complete all as specified and as directed by Engg-In- Charge

Supply and fixing 2nd class hardwood bullnosed splayed, chamfered or rounded on edge fillets rectangular in section, sectional area exc 6 but n. exc 13 Sqcm fixed in repairs fixed with nails complete all as specified and directed by Engg-In- Charge

All as per item No 27 above but sectional area exc 13 sq cm and not exc 25 sq cm complete all as specified and directed by Engg-In- Charge .

S & F Aluminium, anodised, barrel tower bolts of extruded section and fixed 150 mm length.

S & F Aluminium handles, cast type, anodised of length 150 mm

S & F in SS butt hinges 150 mm size

S & F Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed of length 300 mm

S & F in repairs Aluminium alloy wire cloth,0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed withaluminium wire staples.

Hacking out broken glass panes of any description from wooden frames fixed with beads.

S&F 4mm thick pin headed type ordinary quality in square n.exc 0.50 sqm each fixed to aluminium window frame.

M&L aluminium powder coated drapery rod of 20 mm dia including curtain rings (minimum 6 Nos for each curtain rod) complete.

S&F aluminium powder coated fancy type domes cum bracket (20 mm dia) fixed to both ends of the drapery rod and wall complete all as specified and directed.

M&L applying one coats of white wash on old plastred surfaces including preparation of surfaces as in ceiling all as specified.

M&L applying one coat of oil emulsion distemper white or tinted on wall after necessary preparation of surface including removal of swelled popup paint, cracks and applying wall care putty to make the surface even complete all as specified.

Complete removal of existing treatment of wall by washing, rubbing down complete

S & F in repairs Pillar taps of 15 mm dia , cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot' or ‘Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed.

S & F pvc connectors of 15 mm size with PTMT nuts of length 600 mm length

S & Fin repairs PVC waste pipe of 32 mm dia 800 mm length

S & F in repairs CP grating of size 100 mm

S & F in repairs 10 ltrs capacity PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets.

S & F in repairs Stainless steel sink coupling of external 110mm dia along with necessary fittings.

S & F in repairs Vitreous China wash basin, white, flat back, size 550 x 400 mm excluding water taps waste chain plugs and porcelian stopper but including brackets

S&F CP brass pillar tap 15mm, screwed down high pressure fancy type.

Taking down & refixing PVC SWR 110/150 mm bore pipes single socketed in any lengths & to any height with rubber ring joints fixed to wall complete all as specified and directed.

Taking down CI soil/ waste/ vent/ pipes including all fittings like shoes bends swan necks etc of any dia all as specified and as directed. ( Inclusive of scaffolding of any hight )

S & F CI soil/ waste/ vent pipe s in any length with ears 100mm bore ISI marked (sand cast) in any length with cement joints fixed to walls complete all as specified and directed

S & F CI bends or tee( any radius ) for soil / waste pipes 100 mm bore diminishing pieces or tapers on walls complete all as specified.

S & F CI branch pieces single (equal or unequal ) ordinary or inverted (spigot or socket type) wirh parallel branches for 100mm bore pipe all as specified and directed

Demolition of lime/cement Concrete of any description and in any position not otherwise specifically provided for including china mosaic & wc debries remove from MoD land.

M&L for roughening the surfaces of old cement concrete floor by picking, cleaning and washing down with water to remove dust etc. rendering 15 mm thick in CM 1:3 mixed with water proofing compound and applying two coats of hot bitumen 85/25 grade @ 1.70 Kg/Sqm over vertical sides of sunken floors. (Note : WPC shall be measured and paid seperately)

M&L cement concrete type F2 1:7:12 with 40mm graded stone coarse aggregate in sunken floor all as specified and directed.

Supply only water proofing compound of ISI make.

S & F in repairs Vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe ) including trap set in concrete bedding.

S & F 100 mm bore cast iron 'P' or 'S' trap fixed complete with M-SEAL joint to cast iron 100 mm bore pipe duly fixed in position in repairs complete including closing the wall opening in cm 1:3 or as directed

M&L 32 mm galvanised tubing medium grade as in spout pipe each 50 cm long, cutting to shape as required, cutting through wall of any thickness, fixing in PCC 1:2:4 tpe B-1 making good the damaged portion by rendering in CM (1:4) and finished the surface to match the existing surface complete all as specified.

Unitech Enterprises

P LAXMI AND CO.

ASHOK CONSTRUCTION

Angrahit Services Trading Co

BOB ENTERPRISES

David Construction Co.

M/S V N ENTERPRISES

Nilesh Construction