SPECIAL REPAIR DRAINAGE SYSTEM AT 51 SUB AREA SIGNL PL CHAIN LINK FENCING AT CERTAIN LOC IN THE AOR OF PH II AREA AND NCC LINE BLDG NO 01 AT NARANGI MIL STN UNDER GE NARANGI

Amount

Dismantling of plain or corrugated steel sheeting any gauge/thickness in roof or wall covering complete all as specified and as directed

Material and labour Pre- painted hot dip aluminium Zinc alloy metalic coated trapezoidal profile steel sheet 0.50mm thick (Total coated thickness), any pattern corresponding to IS 15965 : 2012 of durability class 3, four (4) coat atmospheric classification category 3, coating class AZ 150 of an approved colour having yield strength of 550 Mpa as in roof covering/wall cladding, fixed with self tapping screws complete all as specified and as directed.

Material and labour Pre- painted hot dip aluminium Zinc alloy metalic coated plain steel sheet 0.50mm thick (Total coated thickness), any pattern corresponding to IS 15965 : 2012 of durability class 3, four (4) coat atmospheric classification category 3, coating class AZ 150 of an approved colour having yield strength of 550 Mpa as in roof covering/wall cladding, fixed with self tapping screws as specified complete all as specified and as directed. Note: To be executed for provision of ridges and hips.

Dismantling of wall and ceiling boards (fibre, pulp, insulation etc) or insulation boards/slabs of any thickness including cover fillets complete all as specified and as directed

Supply and fix false ceiling with suspended system of size 600X600mm of standard section consisting of main runner of size 15X32mmX0.30mm thick , cross Tee (15X32mmX0.30mm) and wall angle (15X15mm X0.30mm , ceiling suspended with 4 mm dia GI wire hanger fixed with steel dash fastner, butter fly clips, hold down clips etc (Main corner, cross tee& wall angle of MS galvanized with 4 mm thick E board HPSC self textured design pre primered non asbestos fibre cement building boards fixed to false ceiling etc complete all as specified and as directed

Dismantling wrought iron or mild steel work of any description not otherwise provided,complete all as specified.

Material and labour Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates confirming to Fe 410 -W (Gde- E- 250) quality-A etc complete all as specified and as directed

Supply and fix mild steel work in wind tie for roof including securing bolts conforming to Fe 290 grade E 165 etc complete all as specified and as directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) not exc 1.5 Sqm each complete as specified & directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) exc 1.5 sqm but n. exc 4 sqm each complete as specified & directed.

Supply and fix factory made 1.25 mm thick pressed steel frame of size 125 X 60 mm for door with double rebate includings necessary fixing lugs, hinges, locks strike plate etc complete all as specified and as directed

Supply and fix 30 mm thick flush shutter, solid core construction with particle board core and plywood face panel, commercial type on both side complete all as specified and as directed

Supply and fix 35mm thick second class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauge etc (with out sash bar), edges of framing with plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc, sizes of members of shutters all as specified in SSR part-I section 8 clause 8.24 (a) complete all as specified and as directed

Supply and fix powder coated (Miimium thickness of powder coating 50 micron) aluminium sliding glazed window shutter (double leaf glazed shutter and single leaf mosquito proof shutter each in single frame work) without sash bars with anodized aluminium shutter of section 40.00mmx20.00mmx1.10mm thick and window chowkat of section 92.00mmx29.50mmx1.20mm thick including necessary jointing cleats, glazing clips, rubber packing, snap beading, screws, handle, tower bolts and locking arrangement etc. and including 4mm thick sheet glass, tinted quality on panel and stainless steel wirecloth or aluminium anodized wire cloth for mosquito proofing, 0.36mm nominal dia and average width of aperture 1.40mm fixed with aluminium screws and tacks and making good to disturbed surfaces complete all as specified and as directed

Supply and fix mild steel framed work such as grills, gratings, angle iron, mild steel sheets, mild steel round bar, MS flat iron etc.. for chowkhats or doors shutters or windows etc with ends of bars shouldered and/or riveted, wlded or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165 complete all as specified.

Supply and fixing 150mm long aluminium anodised barrel tower bolts of extruded section complete all as specified and as directed

Supply and fix 150mm in size extruded aluminium handles, fabricated type, anodised complete all as specified and as directed

Supply and fixing aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolt of extruded section or cast aluminium alloy and fixed 300mm long complete all as specified and as directed

Supply and fix strainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or galvanized wire staples complete all as specified and as directed

Demolition of brick or stone masonry work built in cement mortar including all quoins, arches, pillars etc complete all as specified and as directed.

Demolition of bricks (laid flat or on edge) or brick tiles in floors, channels, kerbs, aprons, etc. (each layer) pointed in any mortar complete all as specified and directed.

Material and labour for brick work with sub class ‘B’ bricks (locally available best quality) straight or curved on plan exceeding 6m mean radius, built in cement mortar 1:6 complete all as specified and as directed.

Material and labour for Brick work but except bricks using class 'B' old sized bricks straight or curved on plan exc 6m mean radius and built in CM 1:6 etc complete all as directed. (Note: Old serviceable bricks as obtained from item no 20 against demolition)

Material and labour for Bricks, sub class B,(using old size bricks) laid flat, in to sides of drain bedded and jointed in cement mortar (1:6) and pointed in cement mortar (1:3) complete all as specified and as directed.

All as per item no 24 here-in-before but except brick, old brick obtained from item no 21 here-in- before shall be re-used complete all as specified and directed.

Material and labour for Bricks, sub class B,(using old size bricks) brick laid on edge of drain bedded and jointed in cement mortar (1:6) and pointed in cement mortar (1:3) complete all as specified and as directed.

All as per item no 26 here-in-before but except brick, old brick obtained from item no 21 here-in- before shall be re-used complete all as specified and directed.

Material and labour Brickwork with sub class 'B' bricks straight or curve on plan exc 6 m mean radius, built in cement mortar 1:4 complete all as specified and directed.

Taking down cement plaster on brick or stone walls, etc including raking out joints, hacking for key, scrubbing down with water complete all as specified and as directed

Material and labour for 15mm thick rendering in cement mortar (1:4), in two layers, under coat of 10 mm thick & top of 5 mm thick, to fair faces of brick or concrete wall surfaces, top layer 5 mm thick mixed with water proofing compound (@ 200ml/50 kg by weight of cement or as per manufacture's instructions), finished even and smooth without using extra cement complete all as specified and as directed. Note : Water proofing compound to be measured and paid separately as "Supply only".

Material and labour for rendering 15mm thick in cement mortar (1:6) on fair faces of brick work as in compound wall finished even and smooth without using extra cement complete all as specified and as directed

Material and labour for rendering 15 mm thick in CM (1:4) on fair faces of brick work or concrete surface finished even and smooth without using extra cement etc complete all as specified and as directed

Supply only water proofing compound (Liquid) complete all as specified and as directed.

Material and labour for prepration of newaly plaster surfaces of wall, applying a coat of wall care 1.00 mm thick and two coat of acrylic distemper over one coat of primer complete all as specified and directed .

Material and labour for preparation of newely plastered surface of walls and applying two coats of cement based paint over one coat of alkali resitant primer complete all as specified and directed.

Material and labour for preparation of new or previously untreated surfaces of wood and wood based surfaces of any description, not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed

Material and labour for preparation of new or previously untreated surfaces of steel and steel based surfaces of any description, not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint complete all as specified and as directed

Material and labour for two coats of synthetic enamel paints over a coat of primer to surfaces of any description n.exc 10 cm width or girth complete all as specified and as directed.

Demolition of plain cement concrete unreiforced of any description and in any position not other wise specifically provided for complete all as specified and as directed.

Demolition of reinforced cement concrete (reinforcement cut as required to facilitate demolition) of any description and in any position not otherwise specifically provided for complete all as specified and as directed.

Material and labour for cement concrete 1:2:4 type, B1 (using 20 mm graded stone aggregates) as in copings, Chajja kerbs, roof padding/staging of water tank etc including necessary fromwork, weathering, slightly rounded or chamfered angles and throating complete all as specified and as directed

Material and labour for cement concrete 1:4:8 (40mm graded stone aggregate) in Foundations, Filling and Mass Concrete, Foundation of Pole etc. including use and waste of Formwork as required/ordered at Site(s), complete all as specified and as directed.

Material and labour for pre cast RCC cover slab, type B-1, 1:2:4 (Using 20 mm graded crushed stone aggregate ) as in manhole cover slab etc., and set in cement mortar 1:4 including necessary form work complete all as specified and as directed

Material and labour for cement concrete 1:3:6 type C-1 (using 20mm graded aggregate) as in hold fast and filling of pressed steel chowkat etc complete all as specified and as directed

Material and labour for 100 mm thick plain cement concrete (1:2:4) type B2 (using 40 mm graded crushed stone aggregate) as in flooring/ hard standing etc complete all as specified and as directed

Dismantling floor, hearth and wall tiling including cement mortar bedding (but excluding backing), removing rubbish off the premises complete all as specified and as directed

Material and labour for glazed ceramic coloured tiles 300X450X7mm thick set and jointed in neat cement slurry and pointed in coloured cement as in vertical surfaces such as skirting, dados and risers to steps over and including 10 mm thick rendering in cement mortar (1:4) complete all as specified and as directed

Material and labour for coloured Non-skid ceramic tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.18 SQM but not exceeding 0.38 SQM in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match existing surfaces over and including 15mm thick screed bed in cement mortar (1:4) complete all as specified and as directed

Dismantling of stone slabs and tiles of any description or thickness in floors/aprons laid bedded and pointed in any mortar

Material and labour for machine presssd pre-cast concrete interlocking coloured paving Block of glass fibre reinfoced glossy finished vibro compacted any shape and size confirming to IS-15658-2006 of 60 mm thick, M-35 grade to match with grey cement and pigment incl 50 mm thick M Sand cushioning etc complete all as specified and as directed

Material and labour for Factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified & directed.

Material and labour for mild steel TMT bars 10 mm dia and over cut to length, bent to shape as required including cranking, bending and binding with mild steel wire (annealed) not less than 0.9 mm dia as in reinforcement bar complete all as specified and as directed.

Dismantling posts or struts (wood, steel or R.C.C.) any section embedded in natural ground, including taking out embedded portion and making good disturbed ground

Dismantling old unserviceable barbed wire fixed in any type of post complete all as specified and directed.

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, and getting out in Soft/Loose Soil, complete all as specified and as directed.

Material and labour for MS posts and struts as in fencing post including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work like wind ties for roof incl securing bolts etc conforming to Fe-290 Gde E-165 complete all as specified and directed.

Supply and fix straps, supports or stays for rainwater, ventilating pipes, including bolts, if required, hooks (stay), heavy, for large gates, flat iron for fixing chinlink fencing to RCC post, hook and pintle hinges, large hasps and staples; chains' hand made sliding bolts; clamps; hold fasts; will ties; hooks for handing fans; plain angle clats for securing purlins to wood trusses or rafters; knee piece inserts two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and as directed.

Fixing only chain link fencing and including line wire, any mesh, size and type to any type of standards, rails, straining bolts, etc. Including provision binding wire complete all specified and as directed.

Supply only chain link MS galvanized fencing of mesh size 100 MM X 100 MM & 3.15 MM dia of wire etc complete all as specified complete all as specified and as directed.

Material and labour for round bar 10mm dia & over conforming to FE 290 (Gde-e-165) cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and bindingwith the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips cut to length bend to shape complete all as specified and as directed.

Supply and fix for 5 to 10 mm dia Mild steel, screw bold (machine made) with hexagonal or square head at one end and screwed the other, or screwed both ends, each screwed ends to be fitted with washers and one hexagonal or square nuts exc 5cm but n exc 10 cm long complete all as specified and as directed.

Supply and fix for Galvanised. 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails strain- ing bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed (each line wire to be measured).

Taking down carefully aluminium/ copper point wiring for light/fan/ socket/bell or power point incl. All fittings i.e. switch, sockets, ceiling rose, regulators, batten holders, etc. complete removing materials to store for keeping in safe custody site or handed over to contractor as schedule of credit and making good disturbed surfaces of walls, floors, etc complete all as specified and as directed.

Taking down ceiling/exhaust/wall fan including connection wires carefully and deposit to MES store in safe custody complete all as specified and as directed.

Material and labour for point wiring with PVC insulated and unsheathed cable single core multistranded copper conductor 1.5 sqmm size, 1100 volts, FR-LSH grade cable conforming to IS-694 1990 drawn in and including PVC Conduit conclead with all accessories including fabricated MS/PVC terminal boxes fixed flush with wall surface with 3mm thick masonite laminated sheet top cover fixed with brass screw for mounting switches, sockets, regulator etc including 1.5 sqmm single core PVC insulated and unsheathed copper conductor earth continuity conductor to common earth and connecting to earth dolly all as specified for One light or fan point controlled by one 5 Amps switch one way complete all as specified and as directed.

All as per item serial No 65 here-in-before but One 3 pin socket outlet 6 amps on the same board with other switches complete all as specified and as directed.

All as per item serial No 65 here-in-before but One socket outlet 3 pin 6 Amp on independent board complete all as specified and as directed.

All as per item serial No 65 here-in-before but with 2.5 Sqmm single core multistranded copper conductor cable for 6 pin 15 Amp socket outlet on independent board and earth continuity wire with 2.5 sqmm cable complete all as specified and as directed.

Supply and fix switch modular type 6 Amp 240 Volts single one way (ISI marked) complete all as specified and as directed.

Supply and fix modular socket, 6 Amp 2/3 pin combined, 2 module complete all as specified and as directed.

Supply and fix modular switch 1 way 16 amp, 1 module complete all as specified and as directed.

Supply and fix modular socket, 16 Amp 2/3 pin combined, 2 module complete all as specified and as directed.

Supply and fix stepped type modular electronic fan regulator, two module size, flush type complete all as specified and as directed.

Supply and fix ceiling rose, 3 phase/PVC/polycarbonate, isolated body complete all as specified and as directed.

Supply and fixing in repair LED lights fitting 1x 20W, 220V, AC decorative batten type connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed.

Supplyand fix in repair/replacement MCB DB of sheet metal enclosure double door SPN 8 way IP -43 with 200 A rated bus bar and grouted in wall with PCC(1:2:4) type B-1 using 20 mm graded stone aggregate complete all as specified and as directed.

Supply and fix in repair/replacement MCBs, SP 6 to 32 Amps In accordance with IS/IEC 60898-1, 240 V, 50 Hz, 10 kA ,B-series marked fixing in DBs (DBs catered separately in this Schedule) complete all as specified and as directed.

Supply and fix in repair/replacement MCBs, SPN 32 Amps In accordance with IS/IEC 60898-1, 240 V, 50 Hz, 10 kA ,B-series marked fixing in DBs (DBs catered separately in this Schedule) complete all as specified and as directed.

Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and as directed.

Earthing complete with GI earth plate electrode of size 60cm x 60cm x 6mm buried directly in ground vertically at a depth not less than 2.25 metre below normal ground level with top edge of earth plate at a depth not less than 1.5 metre below normal ground level sorrounded from all sides by 15cm thick and packed layer of charcoal dust and common salt fliing in alternate layers etc and connected to and including galvanised earth lead wire 4 mm upto 7.5 mtr by means of bolts, nuts, check nuts and washers made of galvanised iron and protected by light grade 20 mm dia GI pipe connected to main control board and GI pipe medium grade 40 mm bore for watering and including funnel, wire mesh, charcoal salt etc RCC pit cover flush to earth pit 50mm thick reinforced with 8mm TMT bar 100mmC/C and PCC chamber pit with PCC (1:3:6) type C1 (using 20mm graded aggregate) including excavation and earthwork disposal of surplus soil to distance not exceeding 50 metre) and testing after completion all as specified and shown on plate No 3 of SSR Part-I 2009

Supply and fix in repair/replacement LED 60 W building secruity light made up of pressure die cast housing with high efficient LED as lighting source and PC cover having TOP Opening separate driver compartment with IP66 protection and impact resistance of IK07 and suitable for dia upto 43 mm complete all as specified and as directed.

Material and labour for building secruity light bracket made out of 40 mm bore light grade GI Pipe with two sets clamps, with nuts and bolts, bend to shape for fixing street light luminaries all as directed, length of GI Pipe shall not be less than 2.0 mtrs complete all as specified and as directed.

Material and labour for wiring with 2 runs of 4 sqmm, single core,FR-LSH PVC insulated & unsheathed cable conforming to IS-694, 1100 volts with copper conductor multi stranded drawn in and including 20mm dian non metallic PVC grey conduit with all accessories such as Tees, Elbows, junction box, reducers etc as requied alongwith single run of 4 sqmm single core FR-LSH PVC insulated & unsheathed copper conductor as continuos earth wire dolly and connecting to existing main switch board / distribution board of each building / qtr as ordered and testing on completion including taking down old wiring and type of conduit complete all as specified and directed. Note: 2 run of 4 Sqmm cable and 1 run of 4 Sqmm cable along with conduit altogether shall be measured as one unit.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 16.0 sq mm 4 core complete all as specified and as directed.

Supply and spreading clean dry river sand in cable trenches as in cable cushioning complete all as specified and as directed. (Note: Punned thickness shall be measured and paid)

Material and labour for bricks sub class ‘B’ brick old size for cable protection laid in flat in trenches over the cable perpendicular to the direction of cable complete all as specified

Excavation in trenches not exc 1.50 m wide and not exc 1.50 m deep for foundation or for shafts, wells cesspits,man holes etc not exc 10 Sqm on plan and n exc 1.5m in depth and getting out in soft / loose soil complete all as specified and as directed.

Returning filling in including spreading, levelling, watering and well ramming in layers n.exc. 25cm thick complete all as specified and directed.

Removing of excavated soil not exc 50cm & depositing where as directed at a level n.exc 1.5m above starting point complete all as specified and directed.

V.V.Construction (BID ID -3415850)

R S TRADERS (BID ID -3416129)

KAKWANI BUILDERS (BID ID -3409470)

M.P.SUPPLY (BID ID -3409272)