Provn of certain sanctioned Minor and Revenue works in the area of AGE B/R-1 and AGE E/M under GE (West) Delhi Cantt-10

Surface excavation n exc 30cm deep and averaging 15cm deep including getting out in any type of soil complete all as specified and as directed.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in any type of soil complete all as specified Insurance of workmen & cleaning of site, removal of all hindrance's/obstractions unforeseen item like Electric cable, Gas Pipe line etc permission from other department should be responsibility of contractor (MES will only assit in getting permission etc) restoring and getting the same constructed/Repaired/Replacement complete & nothing extra shall be payable. and as directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm. complete all as specified and as directed.

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and as directed.

Filling under floor, spreading and levelling in layers n exc 25cm thick well raming including watering as requred complete all as specified and directed

M&L for Treating the bottom and sides of excavation at the rate of 5 ltr of emulsion per square metre of surface area complete all as specified and as directed.

M&L for Treating the top surface of filled earth and under plinth protection at the rate of 5 litres of emulsion per square metre of surface under sub base flooring or plinth protection etc. complete all as specified and as directed.

M&L for PCC 1:4:8 type D2 using 40mm graded stone aggregate as in foundation filling and mass concrete complete all as specified and as directed.

M&L for PCC 1:2:4 type B1 using 20mm graded stone aggregate as in base flooring coping, bed plates, kerbs including weathering slightly rounded or chamfered and throating complete all as specified and as directed.

M&L for 75mm thick PCC 1:3:6 type C-2 (40mm graded agg) for plinth protection laid in bays and finished even and fair incl filling the joint with bitumen mastic complete all as specified and directed .

M&L for RCC M25 design mix, using 20mm graded stone aggregate in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and as directed.

M&l for RCC M25 design mix, using 20mm graded stone aggregate in Columns, pillars, piers, posts and struts complete all as specified and as directed.

M&L for RCC M25 design mix using 20mm graded stone aggregate in Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and as directed.

M&L for RCC M25 design mix using 20mm graded stone aggregate in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed.

M&L for RCC M25 design mix using 20mm graded stone aggregate in Chajjas complete all as specified and as directed.

Use and waste for Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified and as directed.

Use and waste Formwork to sides of pillars,posts, struts, piers, columns and stanchions complete all as specified and as directed.

Use and waste for Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc.for rough finish surface complete all as specified and as directed.

Use and waste for Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) for rough finish surface complete all as specified and as directed.

M&L for brick work with well burnt sub-class B bricks straight or curved on plain exc 6m mean radius built in CM 1:6 complete all as specified and as directed.

Use and waste for Formwork to chullah hoods, chajjas, troughs and similar items including edges complete all as specified and as directed.

M&L for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

Ditto as above but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders complete all as specified and as directed.

M&L for 18-20mm thick diamond cut calibrated, diamond pre-polished kota stone slab flooring area of each stone slab exceeding 0.30sqm and not exceeding 1.50sqm each in squre (as approved by GE) in floor, steps laid over and including cement screed base 20mm thick screed bedding layer in CM 1:6 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including moulding & bull nosing on the edges and polishing including applying cement slury @ 3kg per sqm complete all as specified and as directed.

M&L for 15mm thick cement plaster on brick or concrete surface in CM 1:4 finished even and smooth surface using extra cement complete all as specified and as directed.

M&L for 10mm thick cement plaster on brick or concrete surface in CM 1:4 finished even and smooth surface using extra cement complete all as specified and as directed.

M&L for 5 mm thick cement plaster on concrete surface of ceiling finished even and fair surface without using extra cement complete all as specified and as directed.

M&L for preparing of newly plastered surface of wall and applying two coat of oil bound distemper over one coat of primer white or tinted and including 1mm thick wall care putty all as specified and directed.

M&L for preparing of new surface of ceiling and applying three coats of white lime wash on ceiling over one coat of primer and including 1mm thick wall care putty complete all as specified and as directed.

M&L for applying Two or more coats of 100% Premium Acrylic Emulsion paint having VOC less than 50gm/ltr and UV resistant as per IS 15489:2004,Alkali &fungal resistance, dirt resistance exterior paint of required shade (Company Depot tinted) with silicon additives @1.43 ltr/10Sqm over and incl priming coat of exterior primer applied @0.90 ltr/10 sqm over new surface with including 1mm thick wall care putty complete all as specified and directed

M&L for water proofing treatment to roof surface with APP water proofing membrane 3mm thick & weighing not less than 3.0 kg/sqm of approved make black finish & reinforced with non woven polyester matt of min 150 gm/sqm laid over a coat of bitumen primer conforming to IS-3384 @ 0.4 Ltr/sqm over prepared roof surfaces, forcing overlap with a propane or a butane gas torch with a overlap of 75mm at sides & 100mm at ends & sealing as per manufacturer's instructions over and including two coat of aluminium paint (0.2 ltr/sqm) on treated surface complete all as specified and directed. Note :- 1. Water proofing treatment shall be got carried out by the manufacturer or their authorised applicator only. 2. Bitumen primer, bitumen and membrane shall be of same make/manufacturer. 3. The APP Membrane to be inserted in the parapet wall/wall by cutting chases of atleast 65X50mm size & making good in CM 1:3. complete all as specified and directed.

M&L for brushing neat cement slurry with 3Kg of cement per sqm complete all as specified and directed

M&L for cement concrete 1:2:4 type B1 using 20mm graded stone aggregate as in roof padding/kerb, mud slopes, rounded or chamfered edge complete all as specified and directed

S & F of box type steel window with side hung shutters including chowkhats and box type hinges with steel handle, hold fast and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and directed.

S&F for Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors/door frames; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as spd and directed.

S&F Factory made 35mm thick second class hard wood plain framed panelled door shutters (Minimum three panels) with lock rail and panels of 9mm thick BWP commercial ply or 12mm thick veneered particle board with commercial veneering on both faces. The sizes of rail and stiles as per IS:1003 ( Part I), kiln seasoned and chemically pressure treated and fixed in position complete all as spd & directed .

S&F factory made 35mm thick 2nd class hard wood glazed / gauged shutters(three panels), open, rebated prepared to receive glass , guage etc W/O sash bars for doors as specified in SSR Part I complete all as spd & directed .

S&F mild steel butt hinges 100mm size complete all as spd & directed.

S&F aluminum anodized barrel tower bolts of extruded section of size 150 mm complete all as spd & directed.

S&F aluminum handles cast type anodised of size 150 mm complete all as spd & directed.

S&F aluminium alloy, anodised, sliding door bolt (length of bolt 300 mm) with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed all as spd & directed.

M&L for preparting new wooden surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as spd & directed .

M&L for stainless steel steel wire cloth 0.36mm nominal dia of wire and average width of apertutre 1.40mm fixed in repair complete all as specified and as directed.

M&L for preparation of new steel surface and applying two coat of synthetic enamel paint over one coat of red oxide primer

Dismantling stone slabs/ kota stone in roofs,suspended floors,chajjas,landings etc any thickness jointed in mortar including thatching any type, mud phuska etc including cleaning the surface by water/air pressure and removal of debrish beyond MOD land complete all as specified and directed

M&L for rendering 10mm thick cement mortar 1:4 on fair face of brick work or green concrete surface alongwith mixing of WPC @3% of cement content complete all as specified and as directed.(Note: WPC rates are included in quoted rate of the item)

M&L for cutting groove in brick wall 75mm wide and 65mm deep and shaping horiaontal face of groove with cement Mortar 1:3 for fixing of APP membrane and filling the groove with PCC 1:2:4 type B0 using 12.5mm graded stone aggregate after inserting membrane complete all as specified and directed.

Supply and fixing Heat Resistant Terrace Tiles (300 mm x 300 mm x 20 mm) with SRI (solar refractive index) > 78, solar reflection > 0.70 and initial emittance > 0.75 on waterproof and sloped surface of terrace, laid on 20 mm thick cement sand mortar in the ratio of 1:4 (1 cement : 4 coarse sand) and grouting the joints with mix of white cement & marble powder in ratio of 1:1, including rubbing and polishing of the surface upto 3 cuts complete, including providing skirting upto 150 mm height along the parapet walls in the same manner.

M & L Rendering 12-15mm thick in Ready Mix plaster on brick work, parapet wall, roof beam floor beam and coloumn etc on brick or concrete surfaces and finished even and smooth, work including taking down cement plaster any description from wall surface and removing rubbish beyond MOD land complete all as specified and directed and necessary scafolding. Note :( See the site before quoting rate and height of bilding up to 4 Storey) .

S&F 1000 Ltr rotational moulded polyethylene water storage tanks cylindrical vertical with closed top) hoisted and fixed in position including necessary fittings after dismantling of old tank all as specified and directed.

Taking up or down 20mm bore dia steel tubing and connections, including cleaning for refixing or removal to store

S&F 20mm bore dia Tube medium grade galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors.

Taking up or down 15mm bore dia steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and as directed.

S&F 15mm bore dia Tube medium grade galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed.

S&F in repair 20mm ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed complete all as specified and as directed.

M&L for providing PMM (Polymer modified cementitious mortar):- (i) Dry sub strate surface and free of debris & dust (ii) Applying Epoxy bond coat on the sound substrate using approved spray machine & ensuring that no pin holes are visible. (In case pin holes are still visible after a coat, a second coat shall be applied to ensure absence of pin holes). (iii) Immediately after application of epoxy bond coat as above apply PMM (Polymer modified cementitious mortar) of 25mm thickness. Note : Application of PMM shall be preferably be in coats of appx 10mm thickness. PMM work shall be executed in fairely rapid successions so as entire work is completed with in 30 mins). PMM shall be pre packed ready to use. (iv) PMM surface to be moist cured for three days followed by air curing in temperature as recommended by manufactuer complete all as specified and directed.

Preparing surface by complete removal of existing treatment of wall any layer incl brooming down or steel wire brushing; scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots all as specified and directed

Preparation of newly plastered surface on wall and priming plaster and other surface with alkali resistant priming paint complete all as specified and directed.

M&L for providing 1mm thick wall care putty on wall surface complete all as specified and directed.

M&L for preparing surface of wall and applying two coat of oil bound distemper all as specified and directed.

S&F Grating doom 100/125mm dia of SS (Minimum weight 25gms) complete all as specified and directed.

S&F in repair PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls 110mm bore of pipecomplete all as specified and directed.

S&F PVC (SWR) couplers 110mm complete all as specified and directed.

S&F pre-painted galvatume aluminium zinc coated GI based corrugated steel sheet 0.50 mm thick of any colour as approved by GE having tensile strength of 550Mpa as in roof covering, ridge, fixed with self tapping screws complete including necessary cutting chases to wall for inserting sheet adjoining to wall complete all as spd & directed.

S&F false ceiling with powder coated GI grid of size 600x600 mm using main Tee of size 24x28x0.40mm prepunched to accept cross tee of size 24x28x0.40mm and wall angles of size 25x25x0.40mm fixed with wall around of size with and including fiber cement board 6mm thick white colour designer tiles as approved by GE of size 595x595 mm placed in the grid and held in position duly suspended by 4mm dia GI wire hanger from the roof with holding down clips, butter fly clips and necessary provision for light fixture etc complete as per manufacturers instructions complete all as spd & directed including dismantling old false ceiling any type.

M&L for mild steel work of squar/rectangular tubular section in post, Roof trusses (framed), trussed, purlins, rafter, crane gantries, rails and fastenings and heavy bracket framing of tube sections including distance pieces, cleats etc. specified and directed.

M&L for preparation of old painted steel & iron surfaces of any description over 10cm in width or girth not otherwise described and applying two coats of syntethic enamel paint complete all as spd & directed.

M&L for powder coated Anodised aluminium door shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, ruber neoprene packing,(handles 2 Nos in each door, 03 Nos hinges , 02 Nos tower bolt in each shutter ) anodised aluminum snap beading screws etc. complete all as specified and directed.

M&L for powder coated Anodised aluminium frame for doors, windows, ventilators, grill, partitions, sliding tracks, aluminium section for shutters suitable for two/three/four track window and aluminium section sliding members incl all necessary fittings and fixtures, jointing cleats, rubber packing etc complete all as specified and directed.

M&L for 4mm thick ACP sheet (Aluminium composite Panel sheet) fixed in aluminium partition/doors/window work including necessary jointing cleats, rubber beading, clips,etc complete all as specified and directed.

M&L for stainless steel wire cloth 0.36 mm nominal dia of wire and average width of apperture 1.40 mm fixed to door / window (steel/wooden) complete all as specified & directed.

M&L for 10 mm thick Virified Ceramic tiles double charged/ultra charged (square / rectangular) polished, area of each tiles exceeding 0.18 sqm but not exceeding 1.00 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bedding in CM 1:6. includig dismantling floor hearth/tiles complete all as specified and directed.

M&L for Glazed ceramic coloured tiles 600x1200mm in vertical surface, (square/ rectangular) set and jointed in neat cement slurry and pointed in white or colour cement to match over and including 10mm thick screed bed/backing in CM 1:4 including taking down plaster/hearth complete all as specified and directed.

M&L for applyinge two coat of plastic emulsion paint surfaces of any description over 10cm girth or width, not otherwise described complete all as specified and directed.

M&L for brick work with sub class 'B' straight or curved on plan exc 6m mean radius and built in CM 1:4 complete all as specified and directed.

S&F for 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC frame as per specification and drawing complete all as spd & directed.

S&F for solid PVC wall lining consisting of 5mm thick wood grain printed PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing complete all as spd & directed including PVC strip/channel/angle etc. complete all as specified and directed.

M&L for cement concrete 1:3:6 type C-2 using 40mm graded agg incl packing under and haunching against sides of 150mm dia (Internal dia) pipe after they are laid and tested complete all as specified (Thickness of concrete bed 150mm) complete all as specified & directed.

M&L for cement concrete 1:3:6 type C-2 using 40mm graded agg incl packing under and haunching against sides of 200mm dia (Internal dia) pipe after they are laid and tested complete all as specified (Thickness of concrete bed 150mm) complete all as specified & directed.

M&L for cement concrete 1:3:6 type C-2 using 40mm graded agg incl packing under and haunching against sides of 300mm dia (Internal dia) pipe after they are laid and tested complete all as specified (Thickness of concrete bed 150mm) complete all as specified & directed.

M&L for Reinforced concrete pipe class NP2, 150mm dia laid in trenches & jointed in cement mortar (1:2) with collars complete all as specified and directed.

M&L for Reinforced concrete pipe class NP2, 200mm dia laid in trenches & jointed in cement mortar (1:2) with collars complete all as specified and directed.

M&L for Reinforced concrete pipe class NP2, 300mm dia laid in trenches & jointed in cement mortar (1:2) with collars complete all as specified and directed.

S&F factory made SFRC drain cover 75mm thick size not exc 1.5 sqm each with enravel marking of year of construction on top of each cover complete all as specified and directed.

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out in hard/dense soil complete all as specified and directed.

PCC 1:2:4 type B1 using 40mm graded stone aggregate as in foundation filling and mass concrete complete all as specified and directed.

M&L for 100mm thick PCC 1:4:8 type D2 using 40mm graded stone aggregate as in sub base flooring complete all as specified and directed.

M & L for light shade or printed Glazed vitrified tiles 10mm thick (square/rectangular) polished, area of each tile n. exc 0.36 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match in patch work repair including 15mm thick Screed bed rendering in CM 1:4 on fair faces of brick work or concrete surfaces including dismantling old tile with backing complete all as specified and directed.

Dismantling Brick tiles or terracing tiles, single layer on roofs including thatching any type, mud phuska etc including cleaning the surface by water/air pressure and removal of debrish beyond MOD land complete all as specified and directed

M & L Rendering 12-15mm thick in ready mix on brick work or concrete surfaces including taking down cement plaster complete all as specified and directed.

M&L for preparation of old treated surfaces of walls and applying two coat of cement base paint using spray gun/roller brushes complete all as specified and directed by Engr-in-Charge.

M&L for preparing surface of wall and applying two coat of oil bound distemper all as specified and directed.

M&L preparation old plastered surfaces of ceiling and applying one coats of white wash all as specified and directed.

M&L for machine cut kota stone slab 20-22mm thick as in floor, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab incl rubbing and polishing surface and incl roughing of old surface complete all as spd & directed.

M&L for machine pressed coloured precast concrete interlocking paver block any shape and size conforming to IS 15658-2006 of 60mm thickness, M-35 grade with grey cement and pigment complete all as specified and directed.

M&L for sand filling under floors as cushion bed for interlocking paver blocks all as spd & directed.

M&L point wiring complete with 1.5 Sqm single core PVC insulated unsheathed FRLS cable 1100 volts grade (ISI marked) with multi stranded copper conductor drawn through and including non-metallic rigid PVC medium grade conduit and conduit accessories (ISI) marked concealed in wall/fixed to roof, ceiling etc and incl provn of 1.5 sqmm PVC insulated multistranded unsheathed copper conductor cable FRLS (ISI marked) as earth continuity conductor, fabricated sunken terminal box made out of 1.60 mm thick sheet steel duly painted concealed in walls, with modular cover plates for housing switches, socket outlets, fan regulators etc, all as specified and as directed.

(a) One light /Ceiling fan/exhaust fan point controlled by one switch.

(b) One 3 pin 5 Amps socket outlet point controlled by one No one way switch on independent board.

(c) One 3 pin 5 Amps socket outlet point controlled by one No one way switch on same board

M&L point wiring with PVC unsheathed multi stranded copper conductor cable 2.5 sqmm FRLS 1100 Volts in New PVC concealed conduit medium grade ISI Marked not less than 20 mm dia in new M S steel terminal boxes modular including one run of using 2.5 sqmm FRLS 1100 Volts copper conductor cable as earth continuity connected to common earth for one 15 A switch socket power point, all as specified

M&L switch Modular type 6 Amp SP one way ISI marked complete all as specified

M&L switch Modular type type 16 Amp SP one way, ISI marked complete all as specified

M&LModular type socket outlet 5 pin 6 Amp flush type, ISI marked complete all as specified

M&L Modular type socket outlet 2 in 1,5 pin 6/16 Amps, ISI marked complete all as specified

M&L ceiling rose 3 phase PVC polycorbonate,isolated body, complete all as specified

S & F Modular electronic fan regulator step type,2 module ,360 degree rotation complete all as specified and directed by engr-in charge.

M&L for earthing of machinery/equipment/panel/installed at power house/subatation, complete with galvanised steel earth palte electrode 600 x 600 x 6 mm thick buried directly in ground (Earth pit not less than 2.5 mtrs deep below ground level) with top edge of the plate not less than 1.5 mtrs below normal ground level connecting to galvanised iron strip 25 x 4 mm as earthing lead by means of bolts, nuts, check nuts and washers of galvanised iron or steel and earth protected by 40 mm dia GI pipe medium grade and connected to distribution board/earthing test point all as shown in electrical plate No.3 of SSR Part-I )2009) and testing on completion all as specified and directed.

Supply and fix in replacement MCB DB SPN 8 way Horizontal, IP - 43 Protection double door 240 V AC 50Hz with for MCB SPN as incomer and SP MCBs as out going with tinned copper bus bar ,neutral link earth link complete.

M&L MCB SPN 40 Amp "B" curve, 10 kA complete all as specified.

M&L MCB SP 6 to 32 Amp "B" curve ,10 kA. complete all as specified.

Supply and fix in replacement LED batten luminaire surface mounted, 4 feet system wattage of 20 Watts with lifetime of 25000 burning hours with 70% of its initial lumen maintained. CRI>80, Power Factor > 0.90, THD< 20%, colour temperature - 6500K, surge protection 3KV in CM, IP-20 protected, meets LED IS specifications, Class - 1, Short circuit and over circuit protection, voltage range - 150 to 270 Volts AC, temperature range 0 to 50 DegreeC, system efficacy at luminarie level > 120 Lumens/watt and including connecting up with PVC sheathed 1.5 sqmm 3 core copper conductor flexible wire from ceiling rose to fitting fixed complete. ..

Supply and fix in replacement 10 watts bulkhead fitting with powder coated die cast aluminium housing with glass/ non yellowing polycarbonate cover, IP65 Protection, System level efficacy of the Luminary - is >100lm/W with a life class of 25,000 burning hours at L70 criteria, Power Factor >0.95, driver with Voltage range 150-270V, Temperature range 0 to 50 Deg, Driver efficiency >85%,THD<20%, CRI>80, Color Temperature-6500K, Surge protection of 4.0 KV, including connecting up with necessary PVC sheathed 3 core 1.5Sqmm copper conductor flexible wire fixed complete all as specified and directed.

Supply and fixing new BLDC fan against old ceiling fans three blade, Robust and reliable inverter motor (brush less DC Motor) powered by ECM technology, BEE 5 star rating for energy saving, rated Air delivery >220 cum/min, AC single phase 230/240 V of size 1200 mm sweep including making connection with three core flexible, copper cable pvc insulated of suitable length, complete all as directed. Note BLDC Fan should work on existing electronic fan regulator.

S & F in replacement pressure die cast aluminium housing LED street light luminaires with IP66 deg. of protection suitable for 40 watt LED fitting duly fixed on 40 mm dia GI mast including 50X 6 mm thick MS flat with suitable size of fastner including making connection flexible copper conductor cable from ceiling rose to fitting complete all as specified and directed. Note : The Contractor quoated the rates incl all accessories like suitable GI pipe mast, 50x6 mm thick MS flat, fashner, nut & bolts, suitable length of flexiable wire.