Improvement of B.B. Pitha Square to Via-Choudhury Sahi, Panda Sahi, Hanuman Mandir of Ganjam NAC ODR from 0/00 to 0/756.

Clearing and grubbing road land including uprooting rank vegetation, grass, bushes, shrubs, saplings and trees girth up to 300 mm, removal of stumps of trees cut earlier and disposal of unserviceable materials and stacking of serviceable material to be used or auctioned, up to a lead of 1000 metres including removal and disposal of top organic soil not exceeding 150 mm in thickness incluidng labour & T&P required etc complete as per the OPWD Specification and direction of the Engineer-in-charge.

Excavation for roadwork in soil with hydraulic excavator of 0.9 cum bucket capacity including cutting and loading in tippers, trimming bottom and side slopes, in accordance with requirements of lines, grades and cross sections, and transporting to the embankment location within all lifts and lead upto 1000m. incluidng labour & T&P required etc complete as per the OPWD Specification and direction of the Engineer-in-charge.

Construction of embankment with approved materials deposited at site from roadway cutting and excavation from drain and foundation of other structures graded and compacted to meet requirement of table 300-2 as per approved Drawing & Technical Specifications & direction of Engineer in Charge and Clause -305 of MoRT&H Specifications for Road & Bridge works (5th Revision) as per direction of Engineer-In-Charge.

Loosening, leveling and Compacting original ground supporting embankment to facilitate placement of first layer of embankment, scarified to a depth of 150 mm, mixed with water at OMC and then compacted by rolling so as to achieve minimum dry density incluidng labour & T&P required etc complete as per the OPWD Specification and direction of the Engineer-in-charge.

Construction of Granular Sub-Base by providing Grading-VI material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with vibratory roller to achieve the desired density, complete as per clause 401 etc complete and direction of the Engineer-in-charge.

Providing, laying, spreading and compacting graded stone aggregates to wet mix macadam specification including premixing the materials with water at OMC in mechanical mix plant carriage of mixed materials by tipper to site laying in uniform layers with Paver in sub-base/ base course on well prepared surface and compacting with vibratory roller to achieve the desired density etc complete and as per OPWD Specification and direction of Engineer-In-Charge.

Construction of dry lean cement concrete Sub-base over a prepared sub-grade with coarse and fine aggregate conforming to IS: 383, the size of coarse aggregate not exceeding 25mm, aggregate cement ratio not to exceeded 15:1, aggregate gradation after blending to be as per Table 600.1, cement content not to be less than 150kg/cum, optimum moisture content to be determined during trial length construction, concrete strength not to be less than 10Mpa at 7 days, mixed in a batching plant, transported to site,laid with a paver and compaction with vibratory roller, finishing and curing as per Clause 601 of MoSRT&H Specifications of Road & Bridge Works (4th Revision)

Construction of un-reinforced, dowel jointed, plain cement concrete pavement over a prepared sub base with 43 grade cement @ 400 kg per cum, coarse and fine aggregate conforming to IS 383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a batching and mixing plant as per approved mix design, transported to site, laid with a fixed form or slip form paver, spread, compacted and finished in a continuous operation including provision of contraction, expansion, construction and longitudinal joints, joint filler, separation membrane, sealant primer, joint sealant, debonding strip, dowel bar, tie rod, admixtures as approved, curing compound, finishing to lines and grades as per drawing and as per Clause 602 of MoSRT&H Specifications for Road & Bridge works (4th Revision) as per direction of Engineer-In-Charge.

Providing and laying 80 mm thick factory made cement concrete interlocking paver block of M-40 grade made by block making machine with storng vibratory compaction of approved size, design & shape, laid in required colour and pattern as per drawing including all labour, transporting, T&P etc complete as per OPWD specification & direction of Engineer-in-charge.

Dismantling Rubble stone masonary in cement mortar including T&P and scaffolding wherever necessary, sorting the dismantled material, disposal of unserviceable material and stacking the serviceable material with all lifts and lead of 1000 metres as per OPWD specification and direction of the Engineer-in-charge.