Construction of Community Centre at Sansad No- XII, Teesta Valley TG, Limbu Gaon,Gahari Gaon, Tamang Gaon, Rangli GP

Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course, scaffolding/staging where necessary (Ground floor).[Excluding cost of chipping over concrete surface](ii) With 1:4 cement mortar (a) 20 mm thick plaster

Neat cement punning about 1.5mm thick in wall, dado, windowsill, floor etc.NOTE:Cement 0.152 cu.m per100 sq.m.

(b) Rendring the surface of walls and ceiling with white cement based wall putty of approved make and brand (15mm thick).

Providing & fixing factory made 30 mm thick factory made solid pvc door shuttermade out of single piece extruded solid pvc profile . The style & rails shall be ofsize of 75 x 30 mm having wall thickness of 5 mm. The style and top bottom railshall have one side a thickness of 15 mm integrally extruded on the hinge side ofthe profile for better screw holding power. 15 mm thickness shall be of singlepiece extruded solid pvc profile whereas it shall be not be made of sheet pastedprofile) . The styles and rails shall be reinforced with MS tube of size 18 mm(±)1mm x 18 mm (±) 1mm x 1mm painted with primer all four corners ofreinforcement to be welded or sealed . solid pvc extruded bidding (push fit type)will be set inside the styles and rails with a cavity to receive single piece extruded5 mm pvc sheet as panel. The styles and rails will be metered cut and join with thehelp of pvc solvent cement, self tapping screw and braket of size 200 x 75 mm /welded at each corner. Single piece extruded solid pvc lockrail of size 100 x 30mm with a wall thickness 5 mm & 15 mm integrally extruded in the middle oflockrail & fixed with styles with the help of PVC solvent cement & self driven selftapping screws of size 100mm x 8mm complete as per manufacturersspecifications and direction of Engineer-in-Charge.a) Factory made Single piece non decorative extruded PVC profiles doorshutter(mat / plain finish)

Iron butt hinges of approved quality fitted and fixed with steel screws, with ISI mark.(viii) 100 mm x 75mm x 3.50 mm.

Anodised aluminium skelecton bolt of approved quality manufactured form extruded section conforming to I.S. specifiction (I.S.204/74) fitted and fixed with cadmium plated screws:.(ii) 225 mm long x 12 mm dia. bolt.

Anodised aliminium D-type handle of approved quality manufactured from extruded section conforming to I.S. specification (I.S.230/72) fitted and fixed complete:.(a) With continuous plate base (hexagonal/round rod).(v) 125 mm grip x 12 mm dia rod.

Supplying, fitting and fixing windows and ventilators with or withoutintegrated grills conforming to IS 1038-1975 and manufactured fromrolled steel sections conforming to IS 7452-1974 with non-frictionprojecting type, box type hinges, glazing clips, lugs locking bracket,handle plate etc, including hoisting in position, straightening ifrequired, fixing lugs in cement concrete ( 1:2:4) with stone chips 20mm down cutting holes and mending good damages to match withexisting surface complete in all respect excluding glazing.(Add extra @ 1.2 % for each additional floors upto 4th floor and @1.5% for each addl. Floor above 4th floor.)In Ground floorFlash butt welded windows and ventilators(No shop priming will be allowed to facilitate inspection ofworkmanship)Without integrated grill(b) Openable steel windows as per IS sizes with side hung shuttersand horizotal glazing bars. [The extra rate admissible for theopenable portion only]

(a) Priming one coat on steel or other metal surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc.

(b) Priming one coat on timber or plastered surface with synthetic enamel oil bound primer of approved quality including smoothening surfaces by sand papering etc.