Repair of Quarter no14 NGO colony occupied by Surinder Kumar Sharma Lab boy residing behind Girls hostel GMC Jammu

Taking out doors, windows and clerestory window shutters (steel or wood) including stacking within 50 meters lead : 15.13.1 Of area of 3 sqm. and below

Providing and fixing aluminum work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixed with dash fastener of required dia. and size including necessary filling up of gaps at junctions i.e, at top, bottom and sides with required EPDM rubber / neoprene gasket felt etc. Aluminum sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminum snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge (glazing, panelling and dash fasteners to be paid for separately.) 22.1.1 For fixed portion 22.1.1.1 Anodized aluminum (Anodized transparent or dyed to required shade according to IS:1868, minimum anodic coating of grade AC 15)

Providing and fixing aluminum work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixed with dash fastener of required dia. and size including necessary filling up of gaps at junctions i.e, at top, bottom and sides with required EPDM rubber / neoprene gasket felt etc. Aluminum sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminum snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge (glazing, panelling and dash fasteners to be paid for separately.) 22.1.2 For shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately.) 22.1.2.1 Anodized aluminum (Anodized transparent or dyed to required shade according to IS:1868, minimum anodic coating of grade AC 15)

Providing and fixing wire gauze shutters using galvanized M.S. wire gauze of average width for aperture 1.4 mm in both directions with wire of dia. 0.63 mm for doors, windows and clerestory windows with ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws as per direction of Engineer-in-charge : Second class Kail wood (35mm)

Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. (Note: -Butt hinges and necessary screws shall be paid separately). Second kail wood (35mm)

Providing and fixing ISI marked oxidized M.S. handles conforming to IS : 4992 with necessary screws etc. complete : 125 mm

Providing and fixing ISI marked oxidized M.S. tower bolt black finish, (Barrel type) with necessary screws etc complete. 9.61.1 250x10 mm

Providing and fixing ISI marked oxidized M.S. sliding door bolts with nuts and screws etc. complete : 9.60.1 300x16 mm

Providing and fixing aluminum sliding door bolts ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete : 9.98.2 250x16 mm

Providing and fixing aluminum tower bolts ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete : 9.99.2 250x10 mm

Providing and fixing aluminum handles ISI marked anodized (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour and shade with necessary screws etc. complete.9.102.2 100 mm

Providing and fixing magnetic catcher of approved quality in cupboard/ward robe shutters including fixing with necessary screws etc. complete. 9.116.1 Triple strip (Vertical type)

Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete.

Providing and applying white cement based putty of specified thickness, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. 13.88.1 1 mm thick

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface.

Wall painting with acrylic emulsion paint, having VOC (Volatile Organic Compound) content less than 50 grams/ liter, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour. 13.90.2 Two coats

Supplying /Providing and fixing wire gauze of average width for aperture 1.4 mm in both directions with wire of dia. 0.63 mm for doors, windows and clerestory windows with ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws as per direction of \Engineer-in-charge

Renewing glass panes, with wooden fillets wherever necessary : 14.7.1 Float glass panes of thickness 4.0 mm (weight not less than 10kg/sqm)

Providing and fixing glazing in aluminum door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineerin-charge. (Cost of aluminum snap beading shall be paid in basic item.) 22.3.2 With float glass panes of 5.0 mm thickness (weight not less than 12.50 kg / sqm)

Providing and fixing 12mm thick prelaminated particle board flat pressed three layer or graded wood particle board (conforming to IS: 12823 Grade-I type-II) in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-incharge. 22.2.1 Pre-laminated particle board with decorative lamination on one side and balancing lamination on other side.

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade, one or more coats on old work.

Finishing walls with Acrylic smooth exterior paint of required shade: 13.119.1 Old work (two or more coats applied @ 1.67 liters/10sqm on existing cement paint surface)

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 meters lead. 15.23.1 For thickness of tiles 10 mm to 25 mm

Providing and fixing 1st quality ceramic glazed floor tiles conforming toIS : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete.

Dismantling old plaster or skirting, raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 meters lead.

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer- in-Charge, in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 ( 1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Raking out joints in lime or cement mortar and preparing the surface for re-pointing or re-plastering, including disposal of rubbish to the dumping ground within 50 meters lead.

Flush pointing with cement mortar 1:3 (1 cement : 3 fine sand) mixed with 2% of integral water proofing compound by weight of cement for flat tile bricks on top of mud phaska : 14.21.1 With non modular brick tiles

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,having thermal stability for hot and cold water supply, including all CP VC plain and brass threaded fittings. This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer-in-charge.19.3.2 Internal work Concealed fixing the pipe with clamps at 1.00 meter spacing including cutting chases and making good the wall etc. 19.3.2.1 15mm nominal outer dia pipes.

19.3.2.2 20mm nominal outer dia pipes.

19.3.2.3 25mm nominal outer dia pipes.

Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required:- (a) White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixer

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C waste fittings complete: 18.28.1 Semi rigid pipe 18.28.1.1 32 mm dia

Providing and fixing 15 mm nominal bore C.P. brass bib cock of approved quality conforming to IS : 8931

Providing and fixing PTMT Waste Coupling for wash basin and sink, of approved quality and colour: 18.69.1 Waste coupling 31mm of 79 mm length and 62 mm breadth weighing not less than 45gms.

Providing and fixing PTMT grating of approved quality and colour. 19.49.1 Circular type 19.49.1.1 100 mm nominal dia.

Providing and fixing PTMT grating of approved quality and colour. 19.49.1 Circular type 19.49.1.2 125 mm nominal dia with 25mm waste hole

Providing and fixing 15 mm nominal bore C.P. brass angle valve for basin mixer and geyser points of approved make conforming to IS : 8931

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622 of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1cement :4 coarse sand) including grouting the joints with white cement and matching pigments etc. complete 11.52.2 Size of tile 600x600 mm

Supplying/providing/ fixing of 4mm to 8 mm thick A.C.P. sheet of superior quality including material, labour, carriage, etc complete job

Supplying/Providing/Fixing of P.V.C Pipe of superior quality including cost material, labour etc complete.(Finolex/Supreme) 75mm diameter

Supplying/Providing/Fixing of P.V.C Pipe of superior quality including cost material,labour etc complete.100mm 6Kg pressure

Supplying/Providing/Fixing of P.V.C fittings of superior quality including cost material,labour etc complete.75MM dia plain bend

110MM dia plain bend

75MM dia door bend

75 mm dia door tee

reducer tee 110mm to 75 mm dia

Labour engaged for cleaning of site

Engaging plumbers

engaging carpenters

engaging welders including welding rod and welding set

Providing and fixing 15 mm nominal bore C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank

Disposal of malba/ dismantled material by way of trolley