SITC of Lift along with related Electrical works at Integrated Office Building,Cooch Behar

SITC of Automatic Lift ( as per manufacturer design & as per detailed specification below conforming to IS ) and putting into operation after final testing in the existing lift shaft complete with all accessories and repairing the damage wall / floor/or any civil work if any etc to complete as required.

Make : Categary-I- OTIS / KONE/SCHINDLER

Type:Bed Cum Passanger Lift.

Load : 13 Passenger / 884 Kg

Control: Microprocessor based with AC variable voltage & variable frequency ( VVVF)

Machine:- Energy efficient machine, Gearless without Machine Room

Position of Machine Room: MRL

Speed: 1.0 Mtrs./ Sec

Floor served: G + 3

Landing: 4 , all on same side

Total Rise: 10.8 m

Operation: Microprocessor based simplex full collective with or without attendant.

Signals: Digital car position indicator,car travels direction indicator in car & at all landing with call registration indicator.

Traveling accuracy:± 5 mm(Micro levelling arrangement )

Car inside :1600 mm wide x 1350 mm deep x 2200 mm high

Door Dimension: 900 mm wide x 2000 mm internal height

Car Enclosure: Stainless Steel sheet (20 SWG) with Hairline finish with hand rail.

Car Ceiling & Lighting: Stainless Steel with hairline finish with LED lighting and Fan

Car Ventilation: Pressure fan with anodised aluminium grill.

Car Flooring : Decorative granite flooring (As per direcion of EIC and according to this Department's Order).

Car Door: Stainless Steel centre opening/Telescopic automatic door provided with V3F controlled door drive system

Landing Door: Stainless steel centre opening automatic door provided with V3F controlled door drive system

Door type: Two-panel to Center opening

Door Opening: Automatic power oprated door with full length Photocell assembly light curtain sensor

PROTECTIVE DEVICES & OTHER ACESSORIES

ARD: Automatic rescue device complete with dry maintenance free batteries as required.for automatic evacuation to the nearest floor in case of power failure / single phasing/others.

Overload Protection:Fully loaded with overload protection.On overloading the lift car will not start with door remaining open and give audio display indication

Emergency lighting in car: Battery operated emergency lighting in the lift car.

Intercom system: Battery operated intercom system in Lift Car, Machine Room & Control Room

Emergency Alarm: Battery operated alarm bell system in lift car and control room

Fireman switch: Fireman switch at main landing terminal.

Voice Synthesizer: Voice announcement system (Voice Synthesizer) in the car to announce the position of the elevator in the hoist way as the car passes or stops at a floor served by the elevator.

Main rope - As per manufacturer's standard conforming to IS

DIMENSION OF SHAFT & POWER SUPPLY

Available Shaft Dimension:2300 mm width and 2300 mm depth

Pit Depth :1350 mm

Overhead : 4200 mm

Electric power supply: AC 415 Volt 3phase, 50 Hz, terminated in machine room as per IS

Note: 1) Rates should be quoted with minor civil works, wall cutting and mending good the damages to the original finish. 2) All the above rates should be quoted inclusive of all taxes & duties, District charges and LWC as applicable, with cost of maintenance, servicing, supply & replacement of spares for 01 (One) year from the date of commissioning. 3) The Agency must procure the materials from the manufacture/OEM or their authorised sales Channel so that the standard warranty/support of the manufacturerer/OEM becomes applicable to the product to be delivered and installed by them. Documents that authenticate such procurement from the manufacturer/OEM or from their authorised sales Channel and standard warranty/support should be sent from the e-mail of Engineer-in-Charge and hard copy of it to be submitted during execution of work/submission of bill. If any refubrished materials are supplied and installed, penal action will be taken as per existing rule. Before execution of the work the prospective bider has to submit layout drawing as per design of OEM dully approved by the OEM. 4) Total is rounded off to the nearest rupees