CA NO GE(H)-63/2023-24 PROVN OF DINING HALL AND PROVN OF B VEHICLE SHED WITH HARD STANDING THE AOR OF AGE B/R-I UNDER GE HISAR AT HISAR MIL STN

Amount

Surface excavation not exc 30cm deep and averaging 15cm deep and getting out in soft/loose soil.

Excavating in post holes (or similar holes) each not exc 0.50 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers n.exc 25cm, watering, and removing surplus soil to a distance n.exc 50 m and making good surface in soft/ loose soil.

Excavation in trenches not exceeding 1.5 m wide and not exc. 1.5 m depth for laying cables, foundation for pole etc and getting out in soft/loose soil complete all as specified and as directed.

Returning filling in incl spreading leveling watering and well ramming in layers n. exc 25cm thick etc complete all as specified and as directed.

Removing excavated material to distance n. exc 50m and depositing where directed at a level n. exc 1.5m above the starting point etc complete all as specified and as directed

M&L for hardcore of broken stone or boulders, gauge not exc. 63mm, deposited, spread and leveled in layers not exc 15 cm thick, watered and rammed to a true surface all as directed.

M&L reinforced cement concrete 1:2:4 type B1 using 20mm graded stone aggregate in beams, cantilevers, bressummers, lintels over 1.5m span and the like. Note :- Reinforcement & formwork shall be measured and paid for separately.

M&L formwork to sides and soffits of floor or roof beams, beam haunching, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. for rough finished flat surfaces of concrete.

M&L PCC 1:4:8 type D2 using 40 mm graded stone aggregate in foundations, filling and mass concrete.

M&L for 75mm thick PCC (1:4:8) type D2 using 40 mm graded crushed stone aggregate as in sub base, surface finished fair and even complete all as specified.

M&L for 100mm thick PCC 1:2:4 type B1 using 20mm graded crushed stone aggregate as in floor finished with spike rolling to surfaces or making impressions of expanded metal, whilst the concrete is green, all as directed

M&L for brick work with old size sub-class ‘B’ bricks, straight or curved on plan exc 6.00 metre mean radius, built in cement mortar 1:6 complete all as specified.

M & L for rendering 15mm thick in cement mortar 1:6 on faces of brick work or concrete surfaces, finished even and smooth without using extra cement complete all as specified.

M&L for rough cast finish plaster by applying the under coat of cement and sand mortar 1:3 not less than 10 mm thick and while it is still in plastic state the roughcast mixture consisting of crushed stone or fine gravel aggregate (size between 6 to 12 mm depending on the texture required) mixed with coarse sand and cement in the ratio of 1: 1: 1 shall be applied and finished even complete .

M & L for rendering 15mm thick in cement mortar 1:4 on faces of brick work or concrete surfaces of walls, finished even and fair complete all as specified.

M&L for preparation of new plastered surfaces and applying two coats of oil emulsion distemper (OBD) of approved shade/tint over a coat of primer on walls all as specified & as directed..

M&L for preparation of newly plastered surfaces of wall & applying two coats of cement base paint of approved shade/tint on walls over a coat of primer all as specified & as directed.

M&L for reinforcement TMT bars 10 mm dia and over cut to length, bent to shape required, including cranking, bending spirally or hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia complete all as specified.

M&L for preparation of new steel and iron surfaces of any description over 10 cm in width or girth and applying two coats of synthetic enamel paint of approved tint over a coat of zinc chrome primer complete all as specified and directed.

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws or ‘L’ type or ‘J’ type or cranked hooks bolts complete all as specified & directed.

S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws or ‘L’ type or ‘J’ type or cranked hooks bolts complete all as specified & directed.

S&F factory made Steel windows, ISI marked, (Box Type) with side hung shutters including box type hinges with steel handle etc complete with glazing bars dovetailed or welded including one shop coat of Zinc chrome primer including making good disturbed surfaces of walls, complete. Notes:- (i) The rate quoted by the contractor are deemed to be included for one shop coat of red oxide zinc chrome primer on steel windows. Nothing shall extra paid on this account. (ii) Glass pane/wire gauze shall be measured and paid separately.

S&F factory made Steel windows, ISI marked, (Box Type) with side hung shutters including box type hinges with steel handle etc complete without glazing bars dovetailed or welded including one shop coat of Zinc chrome primer including making good disturbed surfaces of walls, complete. Notes:- (i) The rate quoted by the contractor are deemed to be included for one shop coat of red oxide zinc chrome primer on steel windows. Nothing shall extra paid on this account. (ii) Glass pane/wire gauze shall be measured and paid separately.

S&F rolled mild steel work as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats, necessary welding etc. conforming to Gde E-250 (Fe 410-W) quality `A’ ISI marked (IS-2062) all as specified and as directed.

S&F rolled mild steel work as in Plates (plain or chequered) channels, Square cut or notched (ordinary and counter sunk) forming holes, without any attachment including necessary welding etc. conforming to Gde E-250 (Fe 410-W) quality `A’ all as specified and as directed.

S&F mild steel framed work as in steel frames, chowkats, doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, doors etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging, also fastening and fixing, conforming to Grade E-165 (Fe 290), complete, all as specified & directed.

S&F mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc 30cm long and dia of neck in exc 20mm but n exc 25mm complete all as specified

S&F mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc 5 cm bot not exc 10cm long and dia of neck not less than 10mm complete all as specified

Supply and fixing factory made 35 mm thick plain framed, paneled shutter (Two panels) with lock rail and panel of 9mm thick BWP commercial ply or 12 mm thick veneered particle board with commercial veneering on both faces, size of rail and styles as per IS : 1003 (Part-I), kiln seasoned and chemically pressure treated using second class Hard Wood rail and styles, fixed to chowkat, complete all as specified & directed.

M&L for PCC 1:2:4 type B1 using 20mm graded crushed stone aggregate as in levelling course 25mm thick finished fair & even complete all as specified & as directed.

M&L for vitrified ceramic tiles 1st quality, 10mm thick (square/rectangular), polished, coloured (light shade as approved), area of each tiles not exceeding 0.36 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles laid over & including 15mm thick screed bed in cement & sand mortar 1:6 complete all as specified and directed.

M&L for vitrified ceramic tiles 1st quality, 10mm thick (square/rectangular), polished, coloured (light shade as approved), area of each tile not exceeding 0.36 sqm, on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles laid over & including 10mm thick screed bed in cement & sand mortar 1:4 complete all as specified and as directed.

M&L for glazed ceramic tiles (coloured) 1st quality, 450mm x 350mm x 7mm thick, on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles laid over & including 10mm thick rendering (as screed bed) in cement & sand mortar 1:4 complete all as specified and as directed.

M&L for 20mm thick Granite slab of approved shade, as in platform etc, bedded & jointed with grey cement slurry and pointed with white cement with admixture of pigment to match with shade of Granite stone including cutting, grinding and polishing (mirror polish i.e. full granite polish as per local trade practice) including required cutting to suit the size of oval type wash hand basin over & including 20mm thick screed bed in cement & sand mortar 1:4 complete all as specified and as directed.

S&F 3mm thick polycarbonate solid sheet, in square/rectangular size, smooth surface, weather resistant, fine finish, bent and pressed including aluminium glazing clips, rubber beading and clear silicon or glazing with oil putty with putty or fixed with beads complete all as specified and directed.

S&F GI powder coated snap grid of sizes 605 mm x 605 mm frame work for false ceiling with main tee 32 x 24 x 1mm thick, cross Tee 26 x 24 x 1mm and wall angle 24 x 24 x 1mm thick, flange covered with PVC thin includng hangers 6mm dia GI (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia 40mm long including Gypsum board 9-12mm thick duly finished surface (thin PVC layer on gypsum board as per maunfacturer's instructions) of size 600mmx600mm thick and the same shall be placed in snap grid as in false ceiling complete all as specified & directed.

M&L for 50mm thick PCC 1:3:6 type C1 using 20 mm graded crushed stone aggregate as in plinth protection surface finished fair and even complete all as specified. Note :- Plinth protection shall be of width as directed and shall be laid to slope of 1:30 in alternative bays not exceeding 3 meter in length. Joints of 6 mm wide and 10 mm deep shall be provided along the wall and bays and same shall be filled with bitumen mastic (1:3).

M&L for galvanized steel water tubing medium grade of 15mm bore with & including all fittings and fixed complete to walls and ceilings or laid in floors all as specified and directed.

S&F Bib taps,cast copper alloy with crutch or butterfly handle, chromium plated, fancy type , screwed for iron pipe or for brass ferrule, for 15 mm bore GI pipe complete all as specified and directed.

S&F 15mm bore stop valve, / Angle valve cast copper alloy, screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions.

S&F Grating doom 125 mm dia with waste hole of PTMT (Minimum weight 40 gms) all as directed.

S&F 20mm bore mild steel powder coated curtain rod with 02 Nos decorative ball type brackets (for each opening) and 02 Nos decorative side stoppers (for each opening) fixed on wall with wooden gutties & screws complete all as specified & as directed.

Supply and fixing 1000 Litre capacity Rotational moulded polyethylene water storage tanks (colour other than black as approved by Engineer-in-charge) triple layered (cylindrical vertical with closed top) ISI marked, hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. complete as specified in SSR Part-I.

S&F Gun metal gate valve with iron wheel head, screwed both ends for iron pipe of 15mm bore.

S&F galvanized mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks or galvanized wire staple complete all as specified.

S&F factory made 35mm thick glazed and skeleton shutters made of second class hard wood, open rebated and prepared to receive glass, gauze etc (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc., sizes of members of shutters as specified in clause 8.24 of Section 8 in SSR Part-I, kiln seasoned and chemically pressure treated, fixed to chowkat, complete all as specified & directed.

S&F in repair kitchen sink with drainage board (overall size 915mm x 460mm and bowl size 410mm x 330mm x 160mm or nearest higher size) ) made from high grade AISI-304 (18/8) stainless steel of 1mm thickness including 32mm bore brass CP waste coupling, plug, washer, 32mm bore and 600mm long PVC waste pipe including fixing cantilever brackets made of MS angle iron 30x30x3mm and flat iron 25x3mm both duly painted with two coats of synthetic enamel paint over a coat of red oxide primer, cutting for and pinning of ends of brackets to errecting stand into wall and making good distrubed portion in CM (1:2) on in PCC (1:2:4) using 20mm graded stone aggregate and connecting union to pipe complete all as specified and directed.

S&F 5mm thick hollow PVC wall lining, single side prelaminated with flat or fancy patterned on laminated side, PVC sheet inclusive of fixing with screws or with solvent cement required at site on walls including necessary corner angles, filltes etc required at site complete all as specified and directed.

M&L for coloured tiles, glossy finish, 25cm x 25cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors with grey cement & pigment, laid over & including 20mm thick screed bed in cement & sand mortar 1:4, complete, all as specified & as directed.

M&L for Continuous brick edging using sub-class 'B' bricks, with width equal to the width of the brick, laid dry on end vertically complete all as specified.

M&L for 150mm bore reinforced concrete pipe, class NP2, laid and jointed (in CM 1:1) complete with collars all as specified & as directed

Material and labour PCC 1:3:6 type C-2 using 40 mm graded stone aggregate in concrete bed to drain pipes including forming cradles in after they are laid and tested complete for 150 mm bore pipe all as specified and as directed.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement including forms, moulds, mitred/stopped ends etc.

M&L for point wiring for one light point controlled by one, one way switch with 1.50 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLS cable 1100 Volt grade including 1.50 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLS cable 1100 Volt grade as continuous earth wire in green colour to common earth and connected to earth dolly laid/drawn into and including concealed PVC rigid non metallic conduit 20mm dia medium grade (ISI marked) with all fittings such as tees, bends etc including sunk type pressed steel box covered with and including 3 mm thick new bakelite laminated sheet top cover ‘Hylam’, complete, all as specified & directed. (Note :- Switches, sockets etc shall be measured and paid for separately under appropriate items of BoQ' ).'

All as per item No 55.00 (here-in-before) but ceiling fan /exhaust fan point controlled by one Number one way switch.

All as per item No. 55.00 (here-in-before) but for one 5 Amp socket outlet on independent board controlled by one Number one way switch on independent board

All as per item No. 55.00 (here-in-before) but for one 5 Amp socket outlet on the same board controlled by one Number one way switch on same board.

All as per srl item No. 55.00 (here-in-before) but for 15 Amp socket out let by using 2.50 Sqmm PVC insulated unsheathed copper conductor cable FRLS multi stranded on independent board including provn of 2.50 Sqmm unsheathed, multistranded copper conductor cable FRLS continues as earth wire connected to earth dolly etc complete all as specified and directed by Engineer-in-Charge.

S&F switch piano, flush type, single pole, one way, 5/6 Amp, 230 Volts all as specified & directed.

S&F switch piano flush type, single pole, one way, 15 Amp, 230 Volts.all as specified & directed.

S&F flush type socket outlet multipurpose 3 Pin 5/6 Amp (with 2 pin outlet also) 230 volts AC complete all as specified and directed.

S&F flush type socket outlet multipurpose 3 Pin 15/16 Amp (with 3 pin 5/6 Amp outlet also) 230 volts AC complete all as specified and directed.

S&F ceiling rose surface bakelite 65mm x 50mm, 3 terminals with back plate etc complete all as specified and directed.

S&F Ceiling fan regulator electronic step type of suitable wattage, 230V suitable for 1200/1400 mm ceiling fan etc complete all as specified and directed.

S&F sheet metal enclosure distribution board SP&N, 8 way, double door, powder coated, protection class IP-42, suitable for mounting MCB, DBs confirming to IS-13032, IS-8632, BS-5484 with min 200 Amp rating copper bus bar, complete all as specified & directed.

S & F MCB SP, 6 to 32 Amps 240 Volts , 'C' curve, 10 KA, IS-8828 marked for fixing in DB complete all as specified & directed. . Note :-Make of MCB shall be same of that DB.

S & F MCB SPN, 40 Amps 240 Volts , 'C' curve, 10 KA, complete. Note :-Make of MCB shall be same of that DB.

S&F Sub main wiring with two single core cable PVC insulated unsheathed of copper multi stranded conductor FRLS cable of size 4 sqmm, 1100 votls grade drawing through and including concealed conduit 25 mm dia medium duty including acessories such as Tee, bend, Elbow etc, ISI marked with and including PVC insulated 4 sqmm unsheathed multistranded FRLS copper conductor cable for earth continuity and connected to common earth dolly including cutting chasing of wall, if required and making good disturbed surface in CM (1:3) and finishig the surface to match with existing surface, etc complete all as specified and directed by Engineer-in-charge including taking down old unserviceable submain wiring. Note:- Two lengths of 4 Sqmm cable, one length of 4 Sqmm cable and one length of PVC conduit will be measured as one length.

S&F LED light fitting 1x22W, decorative ultra slim square profile aluminium LED lighting fixture with high lumen output, environmental friendly, energy efficient ready to use pack all as specified and directed. Make : Havells Cat Part No LHEXBTP7IN1S022 of Havells or Surya Cat Part No 22W - STELLA or equivalent of makes as mentioned in Appx 'C' list of makes.

S&F LED light fitting 1x20W, regal batten for LED incl ultra bright glass LED tube light with very high efficiency, singel / double side connection all as specified and directed. Make : Havells Cat Part No LUMILINEBS20WLED865SPCWH of Havells or Crompton Cat part No CCS-100-20-65-HL2-DP-NWH or equivalent of makes as mentioned in Appx 'C' list of makes.

S&F street light LED light fitting 20 Watt, pressure die cast housing with epoxy powder coating, IP65, connected with and including 0.5 sqmm flexible copper multistranded conductor cable including security light bracket made to shape out of GI pipe 25mm dia light grade 1.5m length and fixed with MS clamps of size 40x5mm - 2 Nos, nuts, bolts and washers fixed on wall all as specified and directed. Make : Cat Part No ENDURAPEARLSL20WLED757SASYTOPCMP of Havells or Cat No LTESSI20WLED of C&S or equivalent of make as mentioned in Appx 'C' list of makes here-in-after

M&L for earthing complete with galvanized steel earth plate electrode 60cmx60cmx6mm thick burried directly in ground (earth pit not less than 2.25 m deep below ground level) with top edge of plate not less than 1.5 m deep below normal ground level and connected to and including galvanized iron earth wire 4 mm dia by means of GI nuts, bolts, check nuts, washers thimbles, etc as shown in electrical plate No 3 of SSR Part-I and connection to main switch board/Test point/panel/equipment and testing on completion including excavation and earth work in any type of soil, returning filling in, and removal of surplus spoil to a distance not exc 50 metre, charcoal and salt in alternate layer 15 cm thick all around the earth plate electrode, MS funnel with wire mesh, GI pipe medium grade 20 mm bore for watering and 15 mm bore upto 7.50 metre long GI pipe light grade for earth wire protection fixed with poles/wall with two clamps, made from MS flat 25 mmx3mm, bolts, nuts and washers, PCC chamber (1:3:6) type C1, 40mm thick precast RCC cover 1:2:4 type B1 shall be provided on CI frame etc complete including taking down existing u/s earthing all as specified & as directed. Note :- PCC chamber shall be constructed at least 1.5m away from the earth electrode and pipe for watering shall be provided in slanting manners.

S&F rigid non-metallic PVC conduit 20/25mm dia with fittings like tees , bends, elbow, reducer, bell mouth tube ends and fixing accessories such as coupler lock, nuts, saddles, pipe hooks etc complete fixed on wall / ceiling all as specified and as directed.

S&F cable FRLS, PVC insulated and PVC sheathed size 1.5sqmm three core multistranded copper conductor cable including PVCwire connection complete all as specified & directed

Supply and fixing ceiling fans copper winding complete with blades, down rods, and accessories 230 V , 1200mm sweep. Min air delivery 210 CFM with service value 6.00 BEE and Five Star rated with brushless with direct current moter (BLDC) with remove control unit complete.

Supply & fixing and testing steel body exhaust fan of 300mm sweep heavy duty, double ball bearing, 1400 RPM, suitable for SP 230 / 250 volt, 50 Hz AC supply complete with louver shutter including fixing / grouting of frame in wall & cutting opening complete with covers & connecting with & including 3 Nos 1.5 sqmm single core, PVC insulated but unsheathed FRLS 1100 volts grade cable with multi-stranded copper conductor from ceiling rose to fan complete.

S&F in replacement LED flood light fitting of cap 120 Watt (or nearest higher Cap), energy saving, environmental friendly, long life, exclusive innovative, die-cast aluminium IP66 protection with high power LEDs as light source, suitable for high mast including all accessories for fixing or mounting complete all as specified and directed.

S&F in replacement twin core flat 6 Sqmm size 1100 volt grade heavy duty cable PVC insulated with aluminum solid conductor over all PVC sheathed complete all as specified and directed.

S&F Air circulator fans heavy duty (Metal body) 230volts single phase oscillating 750mm sweep suitable for wall mounting complete all as specified and directed. Make:- Havells, Bajaj, Crompton

Supply , laying , jointing, testing and commissioning of size 16 sqmm 2 core LT underground cable , 1100 volts grade, XLPE insulated and PVC sheathed, armoured heavy duty with multistrand aluminium conductors IS-7098, laid in trenches /fixed on wall /floor /road /culverts /pole or encased in GI pipe complete all as specified. Note : Sand cushioning, cable protection, GI protection pipe, clamps, jointing kits and excavation & earth work shall be measured & paid for separately.

S&F MS heavy duty down rod of 15mm dia and 1000mm length with necessary cutting / drilling holes and painting for ceiling fans complete all as specified and directed.

S&F LED recess mounting panels 2 feet x 2 feet luminaire of capacity 36 watt suitable to be fixed in ceiling having extruded aluminium frame and super bright LEDs of complete all as specified and directed. Make : Surya Cat Part No SLE FP 36 R22 or Cat Part No VENUSNEOHE2X2R36WLED840PIRSENSOR of Havells or Cat Part No LTCRP36WLED2X2 of C&S or equivalent of makes as mentioned in Appx 'C' list of makes.

M&L for brick covering to underground electric cable using sub class ‘B’ bricks, laid dry, flat, perpendicular to the direction of cable etc complete all as specified and directed.

M&L for Sand cushioning 230mm thickness with dry sand (one layer of 80mm thickness before laying of cable and other layer of 150mm thickness after laying of cable) and punned down to 180mm after laying of cable in trenches for protection of cable complete all as directed. Note :- For the purpose of payment only punned thickness shall be measured.

PRINCE CONSTRUCTION

M/S RR ENGINEERING CO

Balaji Construction Co.

Puja Traders

M/S KAVITA CONSTRUCTION

M/S RAJESH KUMAR & SONS

M/S SM BUILDER CO

M/s Rao Constructions, 1173 Urban Estate-II, Hisar

M/s Durga Traders