Dharapuram Municipality Construction of Knowledge Center at NCP School at Ward No. 6, Suvery No.1 in Dharapuram Municipality

Amount

Earth work excavation for foundation by Mechanical means for Isolated & Combined Footing etc in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by the departmental officers with an initial lead of 100 mts and clearing and levelling including dressing of sides and raming of bottoms etc., complete complying with standard specification and as directed by the departmental officers.- Upto 2.00m Footing Depth.

"Earth work open excavation by manual means in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the excavated earth with a lead of 10 mts. within the compound in places shown by the departmental officers and clearing and levelling the site, etc., complete complying with standard specification and as direct-ed by the departmental officers. "

Supplying and filling in foundation, basement, etc with filling crushed stone sand in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers.

Cement Concrete 1:5:10 (One Cement, Five crushed stone sand and Ten hard broken stone jelly) using 40 mm gauge hard broken granite stone jelly for foundation including dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and including curing etc. complete complying with standard specification and as directed by the departmental officers -Mixing by mechanical means

Supplying and erecting steel centering including necessary supports for plane surfaces for Reinforced Cement Concrete works such as column footings, column pedestals, plinth beams, grade beams, staircase steps, Sill slabs etc. which require only nominal strutting using mild steel sheets of size 90cm x 60cm and 10 BG stiffened with welded mild steel angles of size 25mm x 25mm x 3 mm for boarding, laid with silver oak joists of size 10cm x 5cm & 7.5cm x 5cm as support runner , vertical stiffener, side support and Top Horizontal stiffener spaced at about 60cm to 90cm centre to centre or at suitable intervals etc. complete in all floors complying with standard specifcation. (Payment for centering shall be given after the concrete is laid).

For Grade beam and Footing

Supplying and erecting centering for plane surfaces such as RCC Floor/Roof Beam, Lintels, Cantilever Beams, Bed Blocks etc.. with necessary supports and strutting upto 3.60m height in all floors with all cross bracings using MS Sheets made of 10 gauge thick welded with MS angle of Size 25mm x 25mm x 3mm for boarding laid over Steel adjustable Span of Size 2m x 2m(expandable upto 3.60m) and Silver Oak Joists of Size 10 x 5 cm spaced at 50cm to 60cm c/c and supported by Steel Adjustable Telescopic Props of Size 2m x 2m (expandable upto 3.60m) made with outer steel pipe with dia 50mm (3.60mm thick) and inner steel pipe with dia 40mm (2.90mm thick) Spaced at not more than 50 to 60cm c/c , etc complete complying with standard specifications. Steel adjustable span and Steel Adjustable telescopic props shall be provided as directed by the departmental Officers. (Payment for centering shall be given after the concrete is laid).

for lintel ad Roof beam

Supplying and erecting centering for plane surfaces such as RCC Floor/Roof beam, Lintels, Cantilever Beams, Bed Blocks etc.. with necessary supports and strutting above 3.60m upto 4.90m height in all floors with all cross bracings using MS Sheets made of 10 gauge thick welded with MS angle of Size 25mm x 25mm x 3mm for boarding laid over Steel adjustable Span of Size 2m x 2m (expandable upto 3.60m) and Silver Oak Joists of Size 10 x 5 cm spaced at 50cm to 60cm c/c and supported by Steel Adjustable Telescopic Props of Size 2.40 x 3.0m (expandable upto 4.90m) made with outer steel pipe with dia 50mm (3.60mm thick) and inner steel pipe with dia 40mm (2.90mm thick) Spaced at not more than 50 to 60cm c/c and with Cross bracings provided at two levels at a spacing of 1.80m etc complete complying with standard specifications. Steel adjustable span and Steel Adjustable telescopic props shall be provided as directed by the departmental Officers. (Payment for centering shall be given after the concrete is laid).

for FF Lintel Roof beam

"Supplying and erecting centering for plane surfaces such as RCC Floor Slab, Roof Slab, Loft, Landing Slabs, etc with necessary supports and strutting upto 3.60m height in all floors with all cross bracings using MS Sheets made of 10 gauge thick welded with MS angle of Size 25mm x 25mm x 3mm for boarding laid over steel adjustable span of size 2m x 2m (expandable upto 3.60m) and supported by Steel Adjustable Telescopic Props of Size 2m x 2m (expandable upto 3.60m) made with outer steel pipe with dia 50mm (3.60mm thick) and inner steel pipe with dia 40mm (2.90mm thick) , etc complete complying with standard specifications. Steel adjustable span and Steel Adjustable telescopic props shall be provided as directed by the departmental Officers. (Payment for centering shall be given after the concrete is laid). "

For Ground floor Roof slab

Supplying and erecting centering for plane surfaces such as RCC Floor Slab, Roof Slab, Loft, Landing Slabs, etc with necessary supports and strutting above 3.60m upto 4.90m height in all floors with all cross bracings using MS Sheets made of 10 gauge thick welded with MS angle of Size 25mm x 25mm x 3mm for boarding laid over steel adjustable span of size 2m x 2m (expandable upto 3.60m) and supported by Steel Adjustable Telescopic Props of Size 2.40m x 3.00m (expandable upto 4.90m) made with outer steel pipe with dia 50mm (3.60mm thick) and inner steel pipe with dia 40mm (2.90mm thick) with Cross bracings provided at two levels at a spacing of 1.80m ,etc complete complying with standard specifications. Steel adjustable span and Steel Adjustable telescopic props shall be provided as directed by the departmental Officers (Payment for centering shall be given after the concrete is laid).

for First floor Roof Slab

Supplying and erecting steel centering including necessary supports For plane surfaces such as rectangular or square RCC columns etc. which require only nominal strutting using mild steel sheets made of 10 gauge thick welded with MS angle size 40mm x 40mm x 5 mm and supported by Steel Adjustable Telescopic Props of Size 2m x 2m (expandable upto 3.60m) made with outer steel pipe with dia 50mm (3.60mm thick) and inner steel pipe with dia 40mm (2.90mm thick).etc..complete in all floors complying with standard specification. Steel Adjustable telescopic props shall be provided as directed by the departmental Officers. (Payment for centering shall be given after the concrete is laid).

for column

Providing and laying in position, standardised concrete Mix M-20 Grade by insitu machine mix concrete adopting weighing batch method in accordance with IS 456 using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement content of 325 kg/m3 and maximum water cement ratio of 0.55, including admixture (plasticiser / super plasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improve workability without inspiring strength and durability with about (5 Cu.m) 7730 kg. of 20mm machine crushed stone jelly and with about (3.3 Cu.m) 5156 kg. of 10-12mm machine crushed stone jelly and with about (4.79 cu.m) 7670 kg. of crushed stone sand, but excluding cost ofreinforcement grill and fabricating charges, centering and shuttering and also including laying,vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor/ roof slabs wherever necessary without claiming extra, etc.,complete complying with standard specification and as directed by the departmental officers. The coarse and fine aggregates to be used should comply with the requirements of IS standards. (No separate payment will be made by the Department for the excess usage of materials).

Upto basement

Providing and laying in position, standardized concrete Mix M-20 Grade by insitu machine mix concrete adopting weighing batch method in accordance with IS 456 using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement content of 325 kg/m3 and maximum water cement ratio of 0.55, including admixture (plasticizer / super plasticizer) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improve workability without inspiring strength and durability with about (5 Cu.m) 7730 kg. of 20mm machine crushed stone jelly and with about (3.3 Cu.m) 5156 kg. of 10-12mm machine crushed stone jelly and with about (4.79 cu.m) 7670 kg. of crushed stone sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor/ roof slabs wherever necessary without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers. The coarse and fine aggregates to be used should comply with the requirements of IS standards. (No separate payment will be made by the Department for the excess usage of materials).

Above basement Ground Floor

Concrete Mix M-20 Grade in accordance with IS 456 - 2000 using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement content of 325Kg/ cum and maximum water cement ratio of 0.55 including admixture (Plasticizer / super plasticizer) in recommended proportions as per IS 9103 to accelerate, related setting of concrete, improve workability without impairing strength and durability with about (5.0cum), 7730Kg of 20mm machine crushed stone jelly and with about (3.3 cum), 5156kg of 10 - 12mm machine crushed stone jelly and with about (4.79cum) 7670 kg of sand, but excluding cost of reinforcement grill and fabricating charges centering and shuttering but including laying, vibrating with mechanical vibrators, finishing, curing, etc and providing fixtures like fan clamps in the RCC floor / roof slabs wherever necessary without claiming extra cost etc., complete complying with standard specification and as directed by the departmental officers - The Coarse and Fine aggregates to be used should comply with the requirements of IS standards. (No separate payment will be made by the Department for the excess usage of materials) - For First floor

For first floor

Supplying, fabricating and placing in position Mild Steel / Ribbed Tor Steel reinforcement grills of all variety like HYSD/CTD/TMTand all grade like Fe 500, Fe550D, Fe 500 D etc., for all RCC works as per design given including cost of steel reinforcement and G.I. binding wire, wastage etc. complete complying with standard specification and as directed by the departmental officers.(Contractor has to make his own arrangements for the supply of steel reinforcement and binding wire) upto plinth/Basement level

Supplying, fabricating and placing in position Mild Steel / Ribbed Tor Steel reinforcement grills of all variety like HYSD/CTD/TMTand all grade like Fe 500, Fe550D, Fe 500 D etc., for all RCC works as per design given including cost of steel reinforcement and G.I. binding wire, wastage etc. complete complying with standard specification and as directed by the departmental officers.(Contractor has to make his own arrangements for the supply of steel reinforcement and binding wire) Add additional labour for works above plinth/Basement level in every upper floor over the preceding floor or Ground level of 0 to 3.50m . Ground Floor

Supplying, fabricating and placing in position Mild Steel / Ribbed Tor Steel reinforcement grills of all variety like HYSD/CTD/TMTand all grade like Fe 500, Fe550D, Fe 500 D etc., for all RCC works as per design given including cost of steel reinforcement and G.I. binding wire, wastage etc. complete complying with standard specification and as directed by the departmental officers.(Contractor has to make his own arrangements for the supply of steel reinforcement and binding wire) Add additional labour for works above plinth/Basement level in every upper floor over the preceding floor or Ground level of 3.50m to 7.00m. For First Floor.

"Supplying and filling in foundation, basement, etc with conveyed earth in layers of not more than 150mm thick layers well watered, rammed with surface vibrator and consolidated including conveyance charges etc. complete complying with standard specification and as directed by the departmental officers.

"Brick work in Cement Mortar 1:5(One Cement and Five M sand) using best quality Burnt Clay Brick of size 9” x 4 3/8” x 2 3/4” with class designation of 7.5 conforming to IS 1077-1992 for foundation and basement including Cost of Mortar Plasticizer curing, etc., complete complying with standard specification and as directed by the departmental officers. Brickwork shall be done as per IS 2212-1991 adopting English Bond generally. Other type of bond shall be done as directed by the Executive Engineer in charge. Upto Basement

Brick work in Cement Mortar 1:5(One Cement and Five M sand) using best quality Burnt Clay Brick of size 9” x 4 3/8” x 2 3/4” with class designation of 7.5 conforming to IS 1077-1992 for foundation and basement including Cost of Mortar Plasticizer curing, etc., complete complying with standard specification and as directed by the departmental officers. Brickwork shall be done as per IS 2212-1991 adopting English Bond generally. Other type of bond shall be done as directed by the Executive Engineer in charge.- Ground Floor

"Brick work in Cement Mortar 1:5(One Cement and Five M sand) using best quality Burnt Clay Brick of size 9” x 4 3/8” x 2 3/4” with class designation of 7.5 conforming to IS 1077-1992 for foundation and basement including Cost of Mortar Plasticizer curing, etc., complete complying with standard specification and as directed by the departmental officers. Brickwork shall be done as per IS 2212-1991 adopting English Bond generally. Other type of bond shall be done as directed by the Executive Engineer in charge. First Floor

"Brick partition walls of 11.50cm thickness using best quality Burnt Clay Brick of size 9” x 4 3/8” x 2 3/4” with class designation of 7.5 conforming to IS 1077-1992 in Cement Mortar 1:3 (One Cement and Three CS Sand) using hoop iron reinforcement if found necessary including Cost of Mortar Plasticizer, curing etc. complete complying with standard specification and as directed by the departmental officers. (Hoop iron reinforcement will be measured and paid for separately)

"Plastering with Cement Mortar 1:5 (One cement and Five Plastering sand), 12mm thick in all floors including mortar plasticizer at 200ml per 50Kg of cement used, curing etc. complete complying with standard specification and as directed by the departmental officers.

Special ceiling plastering and finishing the exposed surface of all RCC items of work such as slabs, beams, sunshades, facial, canopy slab, staircase waist slab, landing slab etc., with Cement Mortar 1:3 (One Cement and Three Plastering Sand) 10mm thick including mortar plasticizer at 200ml per 50Kg of cement used , hacking the surfaces and curing, etc., in all floors complying with standard specification and as directed by the departmental officers

Supplying, fabricating and fixing in position of Aluminium anodized natural colour matt finish of double leaves door with half paneled with 12mm thick both side prelaminated particle board at bottom and half glazed using 5.50mm thick Plain glass at top. The outer frame shall be with aluminium box section 01.60x44.45x3.18m at 2.319kg/m and Shutter frame made of section-Vertical &Top rail: 50x44.45x2.50mm @ 1.292 kg/m and Bottom rail : 100 x 44.45 x 2.50mm @ 1.974 kg /m , Lock rail: 50x44.45x2.5mm @ 1.292 kg/m,Alu. Clips: 17.15x17.27x1.50mm @ 0.176 kg/m Alu. Handle: 100x30mm @ 0.988 kg/m and necessary accessories such as aluminium clips, rubber beading, PVC felt, handle for a length of shutter (both sides), locking arrangements, furniture fittings such as aluminium tower bolts-250x12mm - 2 Nos., aluminium tower bolt 200x12mm - 1No., aluminium Hydraulic door closer - 2Nos .,lock-1No., Door stopper with rubber bush including cost of materials, labour charges and power consumption charges required for fabrication including chipping, dismantling and making hole to the required extent in RCC column, beam masonry with power drill wherever necessary and redoing the damaged portion to the original condition afterfixing etc. complete complying with standard specification and as directed by the departmental officers.. All the Alu. sections are to be anodized with matt finish under eclectically controlled condition in accordance with IS 1868/1962 for an average anodic film thickness of 15 microns etc., complete. Aluminium sections, and furniture fittings shall be got approved by the Executive Engineer incharge.

"Supplying and Installing Metal False Ceiling using Fire Retardant Galvanized Steel Sheet Plain lay in tile size 600mm x 600mm, 0.5mm thick, powder coated on external surface and shall have flange on all four sides to rest on the exposed grids. The system to give 600mm x 600mm centre to centre 'T'. The 'T' shall be not be dipped GI Tee Section 3600mm long main Tee. 24mm wide and cross Tee panels are formed by running main runner of 'T' section of size 30mm x 24mm powder coated at bottom at intervals with powder coating at bottom. Necessary provision of inter locking of 'T' section are made at required intervals not exceeding 1200mm. The main runners are suspended from the ceiling by means of 4mmdia. GI rods fixed to the ceiling using anchor fasteners of 50mm x 8mm size with nylon inset and hooked to the main rubbers using clips. The last hangers at end of each rubber should not be greater than 600mm from the adjacent wall. The last panel shall be placed at the side wall using edge profile 'L' Angle of size 20mm x 20mm and fixed to the side wall the false ceiling should be fixed of same level and should present a neat look- PWD SOR 2025-26, Page No : 116 "

Dadooing walls with printed design colour glazed tiles of size 300 x 200 x 6 mm thick conforming to IS 15622 of following sizes in Cement Mortar 1:2 (One Cement and Two crushed stone sand),10 thick with Mortar Plasticizer and pointing the joints with Water Resistant Tile Epoxy Grout at the rate of 0.27 Kg. / sq.m. neatly in all floors, curing, etc., complete complying with standard specification and as directed by the departmental officers.(The make and brand of the tiles should be got approved by Executive Engineer before use on works)

"Paving the floor with pre-polished concrete anti-skid tiles (Required shape and design) of 20mm thick of approved quality and colour laid in accordance with IS 1443 over a cement mortar bed of 20mm thick in Cement Mortar 1:3 (One Cement and Three crushed stone sand) with required Cement Slurry and Mortar Plasticizer and pointed with white cement mixed with coloring pigment at the rate of 0.40 Kg. / sq.m., curing, etc., complete complying with standard specification and as directed by the departmental officers. (The make and brand of the tiles should be got approved by Executive Engineer before use on works) "

Paving the floor with best quality Vitrified Tiles of Size : Variety : Double Charged/ Nano polished /Other type 800x800x10mm of following size and variety conforming IS 15622 with water absorption less than 0.08% of approved colour and shade laid over cement mortar bed of 20mm thick in cement mortar 1:3 (one cement and three crushed stone sand) with required Cement Slurry and Mortar Plasticizer in all floors and the top pointed with Water Resistant Tile Epoxy Grout etc., complete complying with standard specification and as directed by the departmental officers. (The make and brand of the tiles should be got approved by Executive Engineer before use on works).

Painting New Plastered Wall Surface with Two finishing coats of ready mixed (Emulsion) of approved quality and colour over one coat priming coat in all floors including the cost of primer etc., complete complying with standard specification and as directed by the departmental officers.(The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)

Supplying and fixing Mild Steel grills for windows, ventilators etc.,including priming coat with one coat of best quality red oxide complete complying with standard specifications and as directed by the departmental officers.

Manufacturing, Supplying and Fixing of Stainless Steel Hand rails for staircase using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick at required locations to a height of 900mm from finished floor level welded to 38mm dia Stainless Steel pipe post of 1.00mm thick as vertical at 900mm centre with 2 Nos. of 25mm dia intermediate horizontal stainless steel pipe of 1.60mm thick in between. The vertical pipe has to be welded to the 100 X 100 X 6mm MS base plate encased in the base concrete. The rate is inclusive of the charges for cutting, bending, welding, grinding, polishing, conveyance, electrical char ges, etc. complete

"Weathering course in brick jelly lime concrete using broken brick jelly of size 20mm uniform gauge in pure slaked lime (no crushed stone sand to be used) to the proportion of brick jelly to lime being 32:12.5 by volume and laid over the RCC roof slab in a single layer of required slope and finished by beating the concrete with wooden beaters of approved pattern, keeping the surface constantly wet by sprinkling lime jaggery water, etc., complete as per standard specification and as directed by the departmental officers. "

"Finishing the top of roof with one course of machine pressed tiles of size 200 mm x 200 mm x 16-18 mm of approved quality in Cement Mortar 1:3 (One Cement add three sand) 12 mm thick mixed with water proofing compound conforming to ISS at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete as per standard specification. "

"Painting new iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with two coats of best approved first quality and colour of synthetic enamel paint over the existing red oxide priming coat in all floors excluding cost of priming coat etc., complete complying with standard specification and as directed by the departmental officers. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.) "

"Supply and fixing of Stainless steel (Salem stainless steel) Door frame ( Box section using stainless steel plate of 1.6mm thick) of size 100mm X 60mm with a rebate of 30 / 35mm X 15mm on one side of the frame including supplying and fixing dovetail splayed end stainless steel holdfast etc. "

"Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Windows of casement type (open) from the profile the size of outer frame 60mm x 58mm and shutter profile are reinforcement with GI/1mm 25GSM and 100% corrosion free, the profiles are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with over all the edges of frame and shutter the shutter will be provided with spag multi power point locks and also it operates as handle. The corners and joints should be welded and cleaned. Radiations free pin headed plain or brown color glass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and should have key lockable action, security protective hinges, strong locking systems and as per size for arresting noise and energy loss. The connecting mechanism between sash and outer frame that enables opening of the window. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The window should be got approved from the executive Engineer before use on work

"Supplying and fixing UPVC (Un-Plasticized Polyvinylchloride) Louvered Ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with GI/1mm 125GSM and 100% corrosion free, the profile are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with all over the edges of frame and shutter. The corners and joints should be welded and cleaned. Radiations pin headed glass 4mm thick should be provided in the louvers. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The ventilator should be got approved from the Executive Engineer before use on work

Providing and laying, spreading and compacting graded stone aggregate to wet mix macadam (WMM) specification including premixing the material with water at OMC in mechanical mix plant carriage to mixed material by tipper to site laying in uniform layers with paver in sub base / base course on well prepared surface and compacting with vibratory roller to achieve the desired density complete as per clause 406 of MORTH specifications.

Supplying and laying Rubberized interlocking Paver block M40 grade Providing and laying of 63mm thick high strength type conforming IS 15658-2006 of rubberized interlocking paver lock in size of minimum compressive strength of 40N/mm2 in uniform shape of approved make to be laid in flurring bone pattern with stone dust cushion below the uniform shape of approved non skirting surface in the top and the rate including levelling the base preparation of pavers as sub base, Stone Dust cushion 100mm thick laying out of pavement cut the pieces to fix the edge vibring the pavers, sweeping transporting loading unloading of laying paver block as per standard specification,.

Supplying, fabricating, erecting structural steel work for roofing welded or bolted type using MS channels, angles, plates and round bars etc. conforming to IS specification including primer coating and enamel painting as per Design given by the departmental officers etc, complete as per standard specification

Supplying , fixing and roofing with colour galvalume sheet of 0.47mm thick with all necessary accessories such as J/V bolt and nuts of suitable length with suitable bitumen washers complete complying with standard specification and as directed by the departmental officers.

Supplying and fixing of ball valve with, bolted bonnet, inside screw, non rising spindle, conforming to IS : 14846 (Sluice valve)/ASTM A105 (Ball valve) - (PN – 10.0) etc. including necessary fittings & testing of valve joints complete as per direction of Engineer in Charge (LR)

25 mm nominal bore

Supplying, laying and jointing PVC pipes (having working pressure 10 kg. / sq.cm) of approved quality and best variety conforming to BIS of the following dia including cutting, threading and fixing PVC specials using PVC adhesives (but excluding cost of such specials) and fixing into wall with teak wood plugs, PVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges upto 4 metre height above ground level, etc., complete complying with standard specifications. The PVC pipes shall be got approved by Executive Engineer before use on works. - External water supply - above ground level/Below ground level

20mm dia PVC pipe

25mm dia PVC pipe

Supplying and fixing in position white / colour glazed European Water Closet of best quality and approved make with 100 mm “P” or “S” trap connecting with CI pipe of 100mm dia / PVC pipe of 110mm dia, double flapped rigid PVC black seat and seat cover with CP brass hinges including cost of white cement, cement for packing, spun yarn,teak wood plugs, brass screws, etc., including supplying and fixing 10 litres capacity PVC / 12.5 litres capacity porcelain low level flushing tank with a pair of CI brackets, etc., complete with all fittings such as 15mm brass ball valve with polythene float with brass handle, union, coupling connected by means of 40mm white PVC flush hand using Indian adopter joint including all internal fittings such as 15mm brass connections, 15mm GM wheel valve, 15mm brass nipple (2 Nos.), 15mm nylon connection, TW plugs, screws and also giving necessary connection to the PVC pipe including cost of 600mm length of 110mm dia PVC pipe and painting the CI brackets with 2 coats of approved paint over one coat of red oxide primer, dismantling the masonry and re-doing the dismantled masonry to original condition etc. complete complying with standard specifications. (The EWC and flushing tank with all accessories should be got approved by the Executive Engineer before use on works)

Supplying and fixing in position Indian water closet of size 580 X 440mm, white glazed earthen ware of approved quality with 'P' trap or 'S' trap confirming to IS:2556 - Part XII with sand cushion and forming flooring alround the closet using 40mm broken brick jelly in lime concrete 1:2:5 ( one part of lime, two parts of sand and five parts of brick jelly) 100mm thick and finishing the top to required slope and including giving necessary connection to cast iron soil pipes/ PVC pipes by dismantling brick masonry, reinforced cement concrete roof/floor slab and making good the disturbed portion to original condition without leakage etc., complete complying with standard specifications and as directed by the departmental officers.

Supply and fixing in position of brass chromium plated screw down Tap 15 / 12mm Dia (Heavy Type) with necessary accessories, , etc.complete complying with standard specifications and as directed by the departmental officers.

Supply and fixing in position of chromium plated stop cock 15mm Dia with necessary accessories, , etc.complete complying with standard specifications and as directed by the departmental officers.

Supply and fixing in position of Porcelain soap dish of size 150mm x 150mm x 50mm with necessary TW plugs, clamps, screws, etc.complete complying with standard specifications and as directed by the departmental officers.

Supply and fixing in position of brass chromium plated towel rail 60cm long and 20mm dia with Brackets with necessary TW plugs, clamps, screws, etc.complete complying with standard specifications and as directed by the departmental officers.

Supply and fixing in position of PVC / Fibre Glass framed 600x450mm size & 5.5mm thick mirror, shelf type with Hard Board Backing with necessary TW plugs, clamps, screws, etc.complete complying with standard specifications and as directed by the departmental officers.

Supply and fixing in position of Stone ware gully trap of size 150mm x 100mm with cast Iron Double Gratings with necessary accessories, , etc.complete complying with standard specifications and as directed by the departmental officers.

Supplying and fixing position CI Nahani Trap / Floor Trap of the following sizes with best stainless steel gratings of approved brand and quality, fixed over a bed of brick jelly lime concrete 1:2:5 (One part of lime, two part of crushed stone sand and five part of 40mm gauge brick jelly) and finished with Cement Mortar 1:3 (One Cement, Three sand) including dismantling masonry works wherever found necessary and making good the dismantled portions to the original condition and giving connection to the CI / PVC pipes, etc., complete complying with standard specification. (The Nahani Trap should be got approved by the Executive Engineer before use on works)

Supplying and laying the following dia un plasticized PVC pipes 6KSC confirming to IS 4985/2000 and relevant specials including packing the joints with rubber /lubricant fixing ,holding wherever necessary and making good of the dismantled portion with necessary connections etc., complete as directed by engineer in charge.

75 mm dia PVC pipe 6KSC

110 mm dia PVC pipe 6KSC

Excavating trenches of required width for pipes including excavation for sockets, refilling.and dressing of sides, ramming of bottoms, depth up to 1.1m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m :

40 mm dia to 160 mm dia - (0.60 m width, 1.05 m depth)

Supply and fixing under ground sump and over head tank Cover with necessary accessories, , etc.complete complying with standard specifications and as directed by the departmental officers.

Manhole Cover Size 900x900 mm double seal, air tight, non-slip SFRC cover & frame for manhole

Manhole Cover Size 60 cm x 60 cm(heavy duty) with frame - SFRC

Supply and fixing of Precast RCC(M30) Bio septic tank of 2.25KLD consists of three chambers - sedimentation chamber,Bioprocessing chamber with PP flower media(virgin plastics bio balls) & settling chamber which shall be coated inside and outside of tank with PU paint for extended life of tank up to 25 years. 2nos of manholes of 500mm shall be provided for easy and safety service. Bio-enzyme shall be used which consists of 20 different types of enzymes and bacteria which can develop in both aerobic and anaerobic conditions and this will start to reduce the BOD and COD of the sewage water and the water will loses its hardness during this process and neutralizes the PH between 6.6 to 7.5. The settled sludge shall be self-digestive. Treated water is orderless and colorless and shall be discharged to Garden/Choke pit/connected to existing sewer line. (Q)

Providing Geophysical survey including all and conveyance, etc., complete

Drilling of Borewell 150 mm dia in Sedimentary formation and hard rock area including labour charges for inserting of casing pipes and supplying and packing of pebbles etc., complete

Supply and delivery of 150 mm dia PVC 6KSC Plain casing pipe etc., complete.as per standard specification

Supply and delivery and fixing of FOllowing liter HDPE tank as per IS 12701 / 1996 including loading, unloading, transportation and labour charges for fixing of the GI pipes and specials for pipe connection works including cutting, threading and fixing charges etc.,

2000 liter capacity HDPE tank

1000 liter capacity HDPE tank

Supplying and erecting in position of following 250 liters capacity Industrial Model Reverse Osmosis Water-cum-Purifier to deliver Potable Water with World Health Organization (WHO) Standards with following accessories. (a) MS Skid - 1 No. (b) Media 11054 No. Vessel with 20 nb Multiport Valve (with Media Pubble and Fine Sand and Activated Carbon Filling) set (c) Feed Pump 0.50 HP – 1 No. (d) Vertical Pump 2-9, 2.00 HP / Single Phase – 1 No. (e) Membrane 40 x 40 filmtech (or) equivalents / Osmonic (USA) - 1 No. and Membrane Pressure Vessel 40 x 40 -1 No. & Pressure Gauge - 2 Nos. (f) Flow Meter - 1 No. 20” Filter with Housing - 1 No., Low Pressure Switch - 1 No., Level Switch - 1 No. & Necessary CPVC Pipes and Fittings. The system shall be provide with Two Panel Control System with necessary Stainless Valves and Fittings and Float Control etc. The rate should be inclusive of all civil works, wherever necessary to install the System in position and intact.

Supply and delivery of clear water vertical wet type submersible pump suitable for 100mm dia borewell THREE PHASE SUBMERSIBLE PUMPSET SUITABLE FOR 100MM DIA BOREWELL AS PER IS 8034/2002 WITHOUT PANEL BOARD as amended thereafter and BEE 3 Star Rated capable of discharging noted LPM against head of water column due to all causes. The pump shall be with stainless steel shaft and dynamically balanced bronze or Cast SS impeller, brass screws and CI FG 200 grade pump bowl/diffuser with ISI mark. The pump shall be directly coupled to a continuous rated two pole suitable wet type vertical squirrel cage induction motor as per IS9283 /1995 and as amended there after, suitable for operation in AC three phase 415 V+/- 10 %, 50 HZ +/- 5 % (100LPM and 100M Head)

Supply and delivery of direct online starter 4 HP THREE PHASE PANEL BOARD- D.O.L WITH TWO LEVEL GUARD AND AUTO START, IEC60947-1 and as amended thereafter with suitable KW rating for operation in AC/Three Phase/50HZ(± 5%) and 415 V(±10%) including Ammeter, Voltmeter, Thermal Overload relay, 16 Amps 2 pole Magnetic Contactor with under Voltage protection, Indication lamp, starting capacitor, running capacitor and On/Off Push button switches, 5 way connector, wiring with 1 sq. mm/1.5 sq. mm copper PVC insulated cable, powder coated vermin proof box including the capacitor (the cost of capacitor is to be taken separately).

Supply and delivery of MS Kiosk of size 0.75m x 0.45m x 0.75m made up of MS angle of size 50mm x 50mmx 4mm alround covered with 16 gauge MS sheet and kiosk door made up of MS plates of size 25 mm x 3 mm including cutting, welding, grinding, locking arrangements and labour charges etc. WD-M1471

Supply and Fixing of PVC INSULATED AND SHEATHED 3 CORE FLAT TYPE COPPER CABLE CONFORMING TO IS 694/1990 AND AS AMENDED THEREAFTER 4 sqm 3 core copper cable TWAD SOR 2024-25, Page No : 124

Supply and fixing of 40 mm dia HDPE Hose pipe(4Kg/sqm) Including laboue and materials M-1057

Supply and fixing of following GI pipe and specials including cost of materials and fixing charges etc complete

32 mm dia GI hex nipple (TWAD page 44, item no - 5.1b)

32 mm GI pipe (TWAD page 40, item no - 5.0)

32 mm dia GM NRV (TWAD page 45, item no - 5.2)

32 mm dia GI union (TWAD page 44, item no - 5.1b)

Nylon rope (PWD SOR , Page 105)

Bore cover (PWD SOR , Page 105, Item No.393c)

M.S.Clamp set 150mm (Q)

32 mm x 20 mm dia GI reducer (PWD SOR , Page 47)

20 mm dia GI coupling (PWD SOR , Page 84)

32mm dia GI Coupling (PWD SOR , Page 84)

Supply and fixing of following PVC pipe and specials including cost of materials and fixing charges etc complete

32 mm dia PVC pipe (10Kg/sqm) (PWD SOR , Page 100)

32 mm dia PVC tee (PWD SOR , Page 100)

40mm dia PVC pipe (PWD SOR , Page 99)

40mm dia PVC Coupler (PWD SOR , Page 99)

40mm dia PVC Elbow (PWD SOR , Page 100)

40mm dia PVC Tee (PWD SOR , Page 100)

Wiring with 2x1.5 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100V grade insuitable PVC rigid pipe concealed in wall and ceiling with PVC accessories inflush with wall with 3mmthick hylum sheet cover withTW switch box and 5AFT switch with continuous earth wire connection of 1.5sq.mm copper wire for making good of the concealed portion with suitable colour for PVC concealed light point / fan point (for electronic regulator) SD 23

Wiring with 2 x 1.5 sqmm (22 /0.3 ) PVC insulated single core unsheathed copper conductor cable of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories inflush with wall with 150 x 100 x 113 mm TW switch box with 3mm hylum sheet cover for 5A 3 pin non inter locking CS plug with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour for concealed PVC plug point. SD 38

Supply and run of 2 of 1.5 sqmm (22/0.3) PVC insulated SC unsheathed Cu.Conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour. SD 54

Earthing as per P.W.D. standard with an earth electrode of 2Mtr. Class 'B' GI pipe of dia not less than 32mm complete with necessary masonry work.SD 222

Supply and fixing of Horizontal type 4 way triple pole neutral MCB distribution board in sheet steel enclosure with 40 A 4 pole MCB isolator as incoming and 12 Nos. 6A to 32 A SP MCB as outgoing in flush with wall and making good of the concealed portion with earth connection. The MCBDB and MCB's should be with the ISI mark (lik standard make) (SD. 540)

Supply and run of 2 of No.8 SWG GI wire for guarding with cradle with No.8 SWG GI wire at the equal interval of 1.5m (SD.75)

Supply and run of 4 X 6 sq.mm (84/0.3) 7/20sqmm PVC unshealed copper cable in suitable PVC rigid pipe concealed on wall and ceiling withcontinuos earth wire connection of 14 SWG TC wire with painting of suitable colour SD 68

Supply and fixing of 300mm (12") sweep AC exhaust fan complete with necessary wall opening and making good of the wall. SD 115

Wiring with 2 x 4sqmm (56 /0.3 ) PVC insulated single core unsheathed copper conductor cable of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories inflush with wall with 150 x 100 x 113 mm TW switch box with 3mm hylum sheet cover for 15A 3 pin non inter locking CS plug with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour for concealed PVC power plug point.SD 40

Supply and clarnping of 2 x 6 sq.mm. PVC armoured Copper LTUG cable on post or on wall with MS clamps etc complete as directed by the departmental officer SD 216)

Supplying and fixing of cable gland and termination with earth connection of size 2 core 10 sqmm etc, complete as per standard specification. (SD 160)

Supply and fixing of TNEB Board suitable for 3 Phases 63A service connection made up of suitable angle iron frame work of size 2 feet x 1 1/2 feet using angle iron of size 1 1/2" x 1 1/2" x 1/4" rigidly fixed on wall covered with hylem sheet of size 2 feet x 1/2 feet of 6mm thickness with necessary bolts and nuts supports and supply and fixing of 3 Nos 63A fuse units(500V) 1 No. Neutral link, copper earth flat of size 1" x 1/4" with inter connection of EB meter to fuse units by 7/16 PVC insulated copper wire with earth connection complete.SD 12

Supply and fixing of 32 A TPN MC switch on incoming and 3 Nos 32 A DPMC Switch (Front Handle) as outgoing with suitable adaptor box with suitable MS cable entry box trunking boxes and internal connections on internal connections on suitable AI frame work with earth connection etc, complete.SD 172

Supply and fixing of 4 way Horizontal Triple pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 No 32A 4P MCB as incoming and 12 Nos 6A to 32A SP MCB as outgoing in flush with wall with Earth connection only. Higher End.SD 547

Supply and run of 2 of 4sq.mm.PVC insulated SC unsheathed FRLS copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earthwire connection of 4sq.mm copper wire and making good of the concealed portion with suitable colour (SD 57)

Supplying and Laying of 3½ x 50 sq.mm PVC armoured LTUG cable in a trench to be excavated at a depth of 0.75 M putting 0.15 M layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good. [ SD 207]

Supplying of 4 x 10 sq.mm PVC armoured LTUG cable in a trench to be excavated at a depth of 0.75 M putting 0.15 M layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good. [SD 196 ]

Supply delivery of installation, testing and commissioning of pre-wired 18W LED Down light fitting suitable for Surface complete with all accessories etc.

Supply and fixing of 65mm dia GI pipe (Class 'B') of 4 metre length with 300mm x 300mm x 6mm MS base plate duly welded at the bottom and with concreting and construction on masonary pedestal with MS box of 30cm x 20cm x 10cm with angle iron frame work with door with lock and key arrangements and with supply and fixing of 25 W LED street light fitting with bulb and with supply and fixing of 16A fuse unit (500V), 5A SP switch inside the MS box and painting with suitable colour SD98

Supply and installation of 2.0TR spilt type AC unit-5 star rated Air conitioner with copper coil and 5 KVA capacity automatic vo;tage stabilizer with time delay relay with 5/8" and 3/8" copper pipe extra byond 3 meter with AC unit and fixing of MS stand for fixing out door unit etc complete as directed by the departmental officer

Supply and fixing of 1200mm sweep Ac ceiling fan with stepped electronic 300W regulator with the existing down rod on the existing clamp (SD -112)

Supply and fixing of 18W LED 3000K Square Type Recessed Fitting (indoor fittings) including cost fixing etc complete. SD 450

Furniture Items Supply and delivery of HIGH BACK CHAIR with Executive ergonomic mesh chair with headrest in Black, 700mm Aluminum base, Adjustable lumbar for excellent back support, Height adjustable back with 5 separate positions, Adjustable tension control, Dual pivot mechanism, Multi-functional 3D adjustable arms, Full diamond mesh, Extra-large executive headrest, Heavy duty SHS gas lift, Waterfall seat, Maximum Weight limit - 150kg, Suitable for 24- hours etc., complete

Supply and delivery of OFFICE CHAIR with Deluxe Mesh chair with folding Arms, Breathable Mesh Back, Air Flow Mesh Seat, Tilt Mechanism lockable in the upright position, Folding Arms, Heavy duty gas lift (110 kilos), Foam and Fabric conform to BS5852 UK FR, W690 x D755 x H960 1060mm etc., complete

Supply and delivery of READING CHAIR with Seat Material - Fabric, Back Type - Mid Back Arm Type - Fixed, Warranty - 1 Year, Brand - MBM Seating Height - 20 - 21 Inches, Color - Black, Height Adjustable - Yes, Seat Height Adjustable - Yes etc., complete

Supply and delivery of COMPUTER CHAIR with Low back chair with arms and plastic outer cover, Primary Material - Castors, Chair base, Gas lifter, chair arm, Press wood sheet, Plastic outer cover, Style - Modern, Finish - Fabric etc., complete

Supply and delivery of CHILDREN'S CHAIR with Lightweight and easy to move, About $15 in materials to build each chair, Easy to build plan designed for a novice woodworker, Uses basic tools, Classic style can is beautiful painted or stained, Storage compartment is big enough for notebooks and more, Works with standard children's tables, Measurement 0.42m X 0.33m X 0.55m etc., complete

Supply and delivery of CLASS ROOM CHAIR with Seat Material - Fabric, Back Type - Mid Back Arm Type - Fixed, Warranty - 1 Year, Brand - MBM Seating Height - 20 - 21 Inches, Color - Black, Height Adjustable - Yes, Seat Height Adjustable - Yes etc., complete

Supplying and fixing of Conference Hall - Half Round Table to site, by using of MDF (Medium Density Fiber) panel sheets for 15 nos of seating capacity, the cost including of material charges, required hinges at bottom support, nails, screws for joints and finish the top with Mica sheet, also including making and labour charges complete. (Total length(straight table) = 4.85m, Curve portion table length = 2.45m, Straight portion Table width = 0.90m) Curveature portion Table width = 0.70m Note: Reading table may also be provided as study table on theatre type having 8 to 10 seats on either side of the table in rows to accommodate 30 seats for reading even during training session.

Supplying and fixing of System table with Key Board Rack to site, by using of MDF (Medium Density Fiber) panel sheets, the cost including of material charges, making charges, Required hinges at bottom support, nails, screws for joints and labour complete. At computer Zone area tables based on number of computers. (Measurements for Computer tables, For each system cabin Length =0.90m, Width = 0.60m, Height of table top from ground = 0.76m, Cabin partition height from table top = 0.25m)

Supplying and fixing of Study Table with Cabin to site, Each cabin length = 0.9 m width = o.60 m height of table top from ground =0.77 m, cabin partition height from table top =0.43 m the cost including of all materials charges,making charges,required hinges at bottom support,nails, screws for joints and labour etc., complete

Supplying and fixing OF Reception table with Fittings to site, by using of MDF (Medium Density Fiber) panel sheets, the table with the size of 2.20m x 0.60m and Height = 0.90m with Required trays and draws and spaces as per site conditions. Computer The cost including of material charges, making charges and labour etc. complete

Supplying and fixing of Librarian table with Fittings to site, by using of MDF (Medium Density Fiber) panel sheets, the table vetch 11 the size of 2.20m x 0.60m and Height 0.90m with Required trays and draws and Computer spaces as per site conditions. The cost including of material charges, making charges and |abour etc., complete,

Supplying and fixing of Manager Room Table to site, by using of MDF (Medium Density Fiber) panel sheets system fittings and keyboard section with the over all table size of 2.20m x 1.10m with Height 12 0.77m to site with required trays and Draws both sides, the cost including of material charges, making charges and labour etc., complete,

Supplying and fixing of Paper Display to site, By using of MDF (Medium Density Fiber) panel sheets the display furniture table size of 2.50 x 0.45m and Height 13 1.23m with Magazine Bay opening Each = 0.25m at both sides ,the cost including of material charges, making charges and labour etc. complete

Supplying and fixing Book racks at Ramp side (4.16m Wgszx =9.81Sqm) to site, BY using of MDF (Medium Density Fiber) 14 panel sheets the cost including of material charges, making charges and labour etc, complete.

Supplying and fixing JO Book racks at Ramp side Off size 3.86m x 1.67m a 6.44 Sq.m, by using of MDF Medium Density Fiber) panel sheets the cost including of material charges, making charges and labour etc., complete,

Supplying and fixing of Book self size 2.45m x 2.22m X 2.22m, by using of MDF (Medium Density Fiber) panel sheets the cost including of material charges, making charges and labour etc., complete,

Supplying and fixing of Children's Table to site for in bottom of OTS area, By using of MDF (Medium Density Fiber) panel sheet and also the table top should be finished with mica sheet of variant colour as per the instruction of Departmental officers, the over all table size of 1.00m 1.00m to site With Height 0.55m with seating capacity of 5 nos (per each table) the cost of including of material charges,making charges and labour etc., complete

Supply, Delivery & Installation of Desktop (with display) with the following specification including cost of materials and labour charges for installing etc., Technical Specification : desktop computer intel core i5 processor,8GB Ram,512GB SSD,window 11,13th gen,keyboard mouse with 21 inch screen etc.SOR 2025-26 M-3113

Supply, fixing and commissioning of 3 PHASE UPS (Three Phase in & Single Phase out) CAPACITY - SYSTEM WITH BATTERY - 2 HOURS BACK-UP with 7.5 KVA including cost of all material and labor charges etc complete.(PWD SOR 2025-26,M-2113 , page no 256 )

Supply and fixing of stored pressure ABC (Mono Ammonium Phosphate) Powder Type Fire Extinguisher of 6 kg. capacity as per IS:15683 with pressure gauge, discharge hose & control nozzle, wall mounting bracket, safety clip etc., including conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition wherever found necessary etc, complete as per standard specification and as directed by the Departmental Officers. Make: EXCELLENT / SAFETY FIRST / EQUIVALENT (PWD SOR 2025-26,M-0851, page no 144 )

Providing rain water harvesting using 3 nos.of RCC well rings of 90cm inner dia (clear) with 5cm wall thickness made out of cement concrete 1:2:4 using 20mm hard broken jelly to a height of 30cm each supplying and fabricating 16 nos. of 6mm dia MS rod vertically and 3 nos. of 6mm dia MS rod circumferentially tied together with 18 gauge binding wire for well rings including necessary earth work excavation 1m dia to a depth of 1m, supplying and filling 40mm HBG inside the erected well ring to a depth of 90cm, and top covered with RCC circular perforated cover slab of 1m dia and 5cm thick which inclusive of cost and fabrication of 6mm M.S reinforcement at 15 cm spacing on both directions and one 6mm M.S rod ties at the edge of the slab circumferentially including cost of molding, curing, finishing and well placing in position and disposing off excavated earth with all initial leads and lifts in places as shown by the Departmental officers etc., complete in all respects.

Add for GST 18%

M MURUGESAN AND CO (BID ID -1483518)