S/R for Ayush Dispensary at village Dhulawat in Nuh District.

Amount

Earth Work in Excavation in foundations, trenches, etc. in all kinds of Soils not exceeding 2 meter depth including dressing of bottom and sides of trenches stacking and excavated Soil clear from the edge of Excavation and subsequent filling around masonry in 15cm layers with Compaction including disposal surplus Soil as directed within a lead of 30 meters (HSR 6.6)

Scraping cement plaster (HSR 8.32 (c))

Cement Concrete 1:8:16 with stone aggregate 40 mm nominal size in foundation & plinth (HSR 10.28)

Cement concrete 1:4:8 with stone aggregate 40mm nominal size in foundation and plinth. (HSR 10.39)

Cement concrete 1 : 1½ : 3 with stone aggregate 20mm nominal Size for reinforced concrete work in slabs with inclination Not exceeding 25 degree with horizontal, excluding steel Reinforcement, but including centering and shuttering, laid in position, complete in all respect. (HSR 10.82+10.95 (a))

Damp proof course 40 mm thick of cement concrete 1:2:4 Using stone aggregate 20 mm nominal size with 2 coats of bitumen 20/30 penetration at 1.65 Kg. per sqm laid Hot and sanded. (HSR 10.114)

Providing and laying 80mm thick interlocking paver blocks of all shapes and colours in design mix cement M-35 over a bed of 30mm thick fine sand complete in all respect. (HSR 10.159)

First class brickwork laid in cement sand mortar 1:6 in foundation and plinth. (HSR 11.2)

First class brick work laid in cement sand mortar in cement sand mortar in 1:6 in first storey upto 4 metres above plinth level (HSR 11.7)

Terracing consisting of tiles 22.86 cm X 11.43 cm X 3.81 cm laid over 87.50 mm mud filling on a layer of 25 mm mud plaster and an other layer of mud mortar for laying the tiles, including two coats of bitumen laid hot at1.65 Kg. per sqm on top of R.C.C. slab including grouting with cement sand mortar 1:3 and top surface to be left clean etc. (HSR 13.13)

Base course of floors consisting of 100 mm thick cement concrete 1:8:16 and 100 mm sand or stone filling. (HSR 14.1)

Providing and fixing vitrified tiles of size 600x600mm of approved make in flooring laid in any pattern as specified over base of 20mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade to tiles. Note:- Tile shall be of premium quality (first quality) of reputed manufacturer like: RAK, NITCO, KAJARIA (Double charged tiles shall be used as approved by Engineer in charge. (HSR 14.89)

Providing and fixing vitrified tiles of size 600 x 600mm of approved make in skirting / dado laid in any pattern as specified over base of 12mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade to tiles. Note:- Tile shall be of premium quality (first quality) of reputed manufacturer like: NITCO, KAJARIA, RAK (Double charged tiles shall be used as approved by Engineer in charge). (HSR 14.90)

Providing & fixing ceramic tiles/anti skid tiles of size 400mm x 400mm or above size of approved make in flooring, laid in any pattern as specified over base of 20 mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade of tiles. Note:- Tile shall be of premium quality (first quality) of reputed manufacturer like:- RAK, NITCO, KAJARIA, SOMANI, JOHNSONS, ORIENTBELL shall be used as approved by Engineer-in-charge. (HSR 14.91)

Providing and fixing 1st quality ceramic glazed wall tiles confirming to I.S. 15622 (thickness to be specified by the manufacturer) of approved make in all colors, shades except burgundy, bottle green, black of any size as approved by Engineer-In-Charge in skirting, risers of steps and dados over 12mm thick bed of cement mortar 1:3 coarse and jointed with grey cement slurry, including pointing in white cement mixed with pigment of matching shades complete. (HSR 14.92)

Laying and fixing vitrified /ceramic anti skid tiles of any size of approved make in skirting, dado, pillars, wall facing laid in any pattern as specified over base of 20mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade of tiles. Note:-Tile shall be of premium quality (first quality) of reputed manufacturer like NITCO, RAK & KAJARIA (Tiles shall be supplied by the Department) (HSR 14.94) (Double charged will be used)

12 mm thick cement plaster 1:6 on walls (HSR 15.7)

15 mm thick cement plaster 1:6 on the rough side of single or half brick wall (HSR 15.12)

10mm thick Cement plaster 1:4 on under side of ceiling (HSR 15.52)

Applying pink primer or aluminium priming coat on wood work including preparation of surface, knotting and stopping etc. (Note:- First quality paint/primer of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge). (HSR 16.2)

Painting two coats excluding priming coat with synthetic enamel paint in all shades on new wood work or metallic or plastered or concrete surfaces to give an even shade. (Note:- First quality paint of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge). (HSR 16.3)

Distempering with washable oil bound distemper (of approved manufacture) two coats over one priming coat on new work. (Note:- First quality paint of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge). (HSR 16.58)

Providing two coats of exterior acrylic emulsion paint. (Note:- First quality paint of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge). (HSR 16.79 (b))

Providing and applying two coats white cement based putty paver plastered surface and grining the surface smooth with sand paper to get an even and smooth finish including cost and carriage of all material, labour charges, scaffolding, sundries etc., complete. (J.K./Birla make) (16.81)

Cost of aluminum fitting complete for doors and windows, such as tower bolt, handles etc. screws for these fittings (excluding sliding bolt) complete. Single leaf shutter (HSR 17.72 (a))

Factory manufactured paneled door or glazed window, shutters, hard wood, such as hollock, champ, Chikrassy and chaplash etc. (Non coniferous timber other than teak, conforming I.S. specification No.1003, kiln seasoned) with 100mm wide bottom rail and 100mm wide vertical style, 150mm wide other rails, with panels of 15mm thck, tongued and grooved of commercial hard wood and including cost of iron hinges, screws, chocks. cleats, stops nails etc. complete, fixed in position (excluding the cost of any fitting other than specified above but including labour for fixing the same in position) 30mm thick (HSR 17.90 (a)) - Note I under 17.18)

Factory –manufactured wire gauze door and window shutters of commercial hard wood such as hollock, champ, chikrassy and chaplash ,etc. (non coniferous timber other teak, conforming to I.S. specification No. 1003, kiln seasoned) with 100 mm wide vertical styles, 150 mm wide lock rail 200 mm wide bottom rail, and wire gauze of 140 G or 120 G designation including cost of iron hinges, screws chock/cleats, stops nails etc., complete fixed position (excluding the cost of any fittings, other than specified above, but including labour for fixing the same in position ) ii) 30mm thick (HSR 17.92 (i))

Factory manufactured solid flush door shutters, with block board core as per I.S No.1659 – 1969 bonded with water proof type phenol formaldehyde synthetic resin, hot-pressed, conforming to I.S 2202 part I & II, fixed in position, including iron hinges, screws, chocks / cleats and stops, etc.(excluding the cost of any fittings other than specified above, but including labour for fixing the samein position:- Commercial veneering with vertical grins or cross bands and faceveneer on both sides commercial facing with laminated core and lipped edges) 35mm thick (HSR 17.93 (iii))

Fe-500 EQR TMT steel bars for RCC works, where not including in the complete rate of RCC including bending, binding and placing in position complete. (NS) Note:- Reinforcement shall be measured in length including hooks, if any, separately for different diameters as actually used in work, excluding overlaps. From the length so measured, the weight of reinforcement shall be calculated in tones on the basis of IS:1732.Wastage, overlaps, couplings, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire or other methods for binding and placing, shall not be measured and cost of these items shall be deemed to be included in the rates for reinforcement.

Pressed steel sheet frames (chowkats) consisting of 2mm thick sheet of specified section including iron lugs (hole fasts) iron hings, conforming to PWD specifications, including bolts for fixing stops locknotch, provision for receiving tower bolts, and finished with one coat of ready-mixed paint red lead non-setting primer, of approved quality, fixed in position including the cost of cement concrete 1:3:6 for filling in the frame, and cement concrete 1:3:6 for lugs complete, door and window frame of size 76mm x 38mm with 35mm wide single rebate. (HSR 18.34 (b))

Excavation for pipe lines running under pressure in trenches and pits in open areas, where disposal of surplus earth is done alongwith the alignment and restoration of unmetalled or unpaved surface to its original condition, ordinary soil. (HSR 6.8 (a))

Cement Concrete 1:8:16 with brick ballast 40 mm nominal size in foundation & plinth (HSR 10.26)

Labour for laying, jointing, fixing and testing G.I./P.V.C./W.I. pipe lines and specials tees bends, sockets elbows etc. inside building and tesitn etc., complete i/c cutting threading. (HSR 28.18) 15mm i/d

Extra for fixing and jointing union coupling in GI and WI pipeline. (HSR 28.21) 15mm dia

20mm dia

Cutting holes upto 23cm through square through brick work in mud walls for pipes and making good including repainting replastering and finishing according to existing finish where required. (HSR 28.23).11.43cm thickness of walls 11.43cm thick wall

22.86cm thick wall

Fixing and jointing gun metal peet (valves Heavy pattern) including cartage. (HSR 28.29) 20mm dia

BAILING OUT WATER FROM THE TRENCHES FOR MAKING NEW CONNECTIONS IN FULLY CHARGED PIPE-LINES including cleaning trimming and dressing the trenches to correct alignment and grade as required by the Engineer-in-charge. (HSR 28.47)

Constructing brick masonry inspection chamber sizes as given below upto 0.60 meter average depth benching 12mm thick cement plaster 1 : 2 RCC 1:2:4 slab 100mm thick / cement concrete topping 50mm thick with 455mmx 455mmx610mm inside light duty C.I. inspection chamber cover and frame with 3 coats of black bitumastic. (HSR 29.84) c) Size 450mm x 450mm inside.

Providing & fixing PVC Rain water pipe 6Kg Pressure of ISI mark in cement mortar during masonry work. 100mm dia PVC pipe 6 Kg. Pressure. (HSR 13.89 (a))

Providing & fixing PVC Bend ISI Mark. (a) 100mm dia PVC Bend (HSR 13.90 (a))

Providing and fixing in position best Indian make (to the approval of the Engineer-in-charge). Indian type orissa or orya water closet suite for sinking into floor, with raised foot treads complete with 100mm H.C.I. ‘P’ Trap with or without vent as required and all other necessary fitting as fully described in item No.30.1 Above (HSR 30.2)

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE EUROPEAN TYPE WATER CLOSET SUITE WITH CONCEALED ‘P’ or ‘S’ TRAP with or without vent (as approved by the Engineer-in-charge) and all other necessary fittings as fully described in item no. 30.3 above (i) White. (HSR 30.6 (i))

Extra over item no. 30.1 to 30.4 for providing and fixing 15 litres capacity low level vitreus china ware cistern complete with flush bend all other necessary fitting instead of C.I. high level citern complete with fitting. (HSR 30.12). I) white plastic seat (solid)

Extra over item nos. 30.3 to 30.6 for providing and fixing best Indian make plastic hygienic seat with lid complete instead of hollow black or white plastic seat and lid. (HSR 30.13). i) white plastic seat (solid)

Proving and fixing in position best Indian make lavatory uites consisting of. (HSR 30.41) (iv) Size 550mm x 400mm with one no. Tap

Providing and fixing in position 15mm i/d C.P. brass bib cocks of best quality (as required by the Engineer-in-Charge). (HSR 30.75) Bib cock long body

Bib cock

Providing and fixing in position C.P. brass stop cocks ( as approved by the Engineer-in-Charge) (HSR 30.76)

Prov. and fixing in position best Indian make flexible tube connection. (HSR 30.82) (a) C.P. brass.

Providing for laying, jointing, fixing and testing G.I. (Medium class "B" type of Tata & Jindal make) pipe lines and specials tees bends, sockets, elbows etc. inside building and testing etc. complete including cutting threading. G.I. specials shall be of Make:- UNIK, TATA, ZOLOTO. (N.S) 15mm I/d

20mm dia

Providing and fixing and jointing union couplings in G.I. and W.I. pipelines. 15mm dia

20mm dia

Providing, Fixing and jointing gun metal peet valves (heavy pattern) with hand wheels, on G.I. pipelines laid in the ground or inside building including cartage from divisional stores or nearest railway station to site of works. (NS) 20mm dia

Providing and fixing HDPE water storage tank of Sintex, Diplast, O.K., Supreme make with covers. Lids marked with IS: 12701 on roof top of buildings including cost of hoisting and placing in position, making connections with inlet and outlet pipes, providing overflow and scour provisions with suitable plus on scour pipe including cost of nipples, washers, flanges for connections in tanks complete in all respects to the satisfaction of Engineer-in-Charge (except civil work) (HSR 30.119) (i) 500 Ltrs.

First class brick work laid in cement sand mortar 1:4 in foundation and plinth (HSR 11.4)

The Rahul Khan Coop LnC Society Ltd.

The Friends Coop L&C Society Ltd.

Shri Shyam Construction Co.

The Sunrise Coop. LNC Society Ltd.

The Arman Co.Op. L and C Society Ltd. Shikrawa

The Unique Co.Op. L and C Society Ltd. Nuh

sahil

NISAR CONSTRUCTION

Ajaj BMS and RMC Plant