SPECIAL REPAIR TO BLDG NO P 76 KOTE OF 7 GARH RIF SI LINES BHOPAL UNDER GE BHOPAL

Note :(i) Please refer Sch A/ BOQ Notes before quoting the tender for all phases/ items mentioned below. (ii) Amount of Schedule of credit shall be deducted offline

Demolition of cement concrete of any description and in any position complete all as specified and directed.

Demolition of cement concrete reinforced (reinforcement cut as required to facilitate demolition) in any description and in any position not other wise specifically provided for complete all as specified and directed.

Demolition of brick work, built in cement mortar including all quoins, arches, pillars etc complete all as specified and directed.

S&F for mild steel work as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastening and heavy brackets framing (beam, tee, angle, channel or flat section) including distance pieces, cleats, etc. of Gde Fe 410-W (Gde-E-250) quality-A including dismantling of old structural steel complete all as specified and directed.

S&F of mild steel framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc; complete, drilled for fixing of steel sheeting or other covering, doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing, steel of Fe 410-W (Gde E-250) quality including dismantling of old steel doors/gates etc. complete all as specified and directed.

S&F of mild steel framed work such as grills, gratings, cooler stands etc., with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work conforming to Fe 290 Gde E-165 incl necessary fixing to openings complete all as specified and directed.

S&F of pre-painted galvalume aluminum zinc coating GI based corrugated steel sheeting 0.50 mm thick of an colour having tensile strength of 550 Mpa (AZ-150) as in roof covering / cladding to wall, chajjas, etc. and fixed with self tapping screws complete all as specified and directed.

S&F of pre-painted galvalume aluminum zinc coating GI based corrugated steel sheeting 0.50 mm thick of an colour having tensile strength of 550 Mpa (AZ-150) as in ridges, hips, valley gutters, drip, straight flashing etc. (length and gith as fixed) and fixed with self tapping screws complete all as specified and directed.

M&L for 25mm thick in PCC 1:2:4 type B-0 (using 12.5 mm graded stone aggregate) as in bedding layer for laying in floor as in levelling course complete all as specified and directed.

M&L for grinding and mirror polishing on marble/ granite/ kota stone/ stone work where ever required to give high gloss finish complete all as specified and directed.

M&L for 18-20 mm thick machine cut kota stone slab in flooring over and including 20 mm thick cement screed base in CM 1:4, laid and jointed with grey cement slurry including rubbing and mirror polishing and dismantling of old stone slab complete all as specified and directed.

M&L for 18-20 mm thick machine cut, single piece, kota stone slab as in steps and risers with anti-skid thread marking as required, fixed over and including 20 mm thick cement screed base in CM 1:4, laid and jointed with grey cement slurry including rubbing and mirror polishing and dismantling of old stone slab complete all as specified and directed.

M&L for non-skid coloured ceramic tiles 7 to 8 mm thick (area of each tiles exceeding 0.11 sqm but not exceeding 0.18 sqm) as in floors and skirting laid over and including 15 mm thick screed bed n CM 1:6, set and jointed in neat cement slurry and pointed in white or coloured cement to match with shade of tiles including dismantling of old tiles fixed in any mortar and position complete all as specified and directed.

M&L for glazed ceramic colour tiles with suitable matching high lighter in vertical surfaces (design and pattern as approved by GE) of size not less than 450 x 300 x 7-8 mm thick, laid over and including 10 mm thick rendering in CM 1:4 as backing coat; set and jointed in neat cement slurry and pointed in white or colour cement to match the shade of tiles including dismantling of old tiles fixed in any mortar and position complete all as specified and directed.

M&L for heavy duty parking /outdoor tiles 9 to 10 mm thick (square/ rectangular) area of each tiles not exc 0.11 sqm as in floors, laid over and including 15 mm thick screed bed in CM 1:4; set and jointed in neat cement slurry and pointed in white or colour cement to match the shade of tiles including dismantling of old tiles fixed in any mortar and position complete all as specified and directed.

M&L for 605 x 605 mm size anodised aluminium snap grid frame work for false ceiling including G.I. hanger wire of 6 mm dia (upto 1200 mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of G.I. flat 40 x 3 mm size & 60 mm long and expansion hold fasteners and dismantling of old ceiling frame with board of any type and size complete all as specified and directed.

M&L for exposed metal frame ceiling with 8 mm PVC coated calcium silicate board of siliceous and calcareous material reinforced with cellulose fibre for fixing in 600 x 600 mm grid complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) not exc. 1.5 sqm each complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) exc. 1.5 sqm but not exc 4.0 sqm each complete all as specified and directed.

Taking down shutters of any description area of each exc 1.0 sqm but n exc 2.0 sqm complete all as specified and directed.

Taking down and refixing shutters of any description of area exc 1.0 sqm but n exc 2.0 sqm complete all as specified and directed.

S&F of 125 x 60 mm pressed steel frames for doors with one or more rebates including necessary supply and fixing lugs, hinges, lock strike plate, etc. complete all as specified and directed.

M&L for cement concrete 1:2:4, type B-0 (using 12.5mm graded stone aggregate) as in filling of door frame of pressed steel, bed blocks and like etc complete all as specifed and directed.

S&F of factory made single extruded WPC (Wood Polymer Composite) solid door frames/ chowkhat of size 45 x 85 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant complete all as specified and directed.

S&F of factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30 mm thickness, comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws complete all as specified and directed.

S&F of factory made 35 mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

S&F for 150 mm long aluminium handles, cast type, anodised and fixed complete all as specified and directed.

S&F for 150 mm long aluminium anodized barrel tower bolts of extruded section and fixed complete all as specified and directed.

S&F for 300 mm long aluminium alloy anodised sliding door bolts with hasp and staple (bolt type) & fixing clip of sheet cast or extruded section & fixing bolt & sliding bolts of extruded section or cast aluminium alloy complete all as specified and directed.

S&F for 100 mm long stainless steel, butt hinges, heavy weight and fixed complete all as specified and directed.

M&L for preparation of newly wooden surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L for preparation of old painted wooden surfaces of any description, not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint complete all as specified and directed.

M&L for prepration of new steel surfaces of any description, not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and directed.

M&L for preparation of old painted steel surfaces of any description, not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint complete all as specified and directed.

S&F in repairs powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (fixed portions) frame and shutters with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, suitable aluminum handle, lock/ mortice lock for door shutter etc all complete as per architectural drawings complete all as specified and directed.

S&F of 4 mm thick plain sheet glass in area n exc 0.5 sqm in each pane and fixed in aluminium or wooden frames complete all as specified and directed.

S&F in replacemnt rotational moulded polyethylene water storage tanks, 3 layers (cylindrical vertical with closed top) of capacity 500 litres, hoisted including all fittings as required and fixed in position complete all as specified and directed.

S&F in repairs 20 mm bore float valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for pipes in water tank and fixed complete all as specified and directed.

S&F in replacement 15 mm bore GI tubing medium grade with all necessary fittings and fixed complete to wall and ceiling or laid in floors complete all as specified and directed.

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc; and making good, cutting not exc 10 cm girth complete all as specified and directed.

S&F in replacement 20 mm bore GI tubing medium grade with all necessary fittings and fixed complete to wall and ceiling or laid in floors complete all as specified and directed.

S&F in repairs 20mm bore gun metal, globe or gate valve with iron wheel head, screwed both ends for iron pipes and fixed complete all as specified and directed.

S&F in replacement vitreous china water closet squatting pan "Orissa Pattern" of size 580 x 440mm white with integral foot rests with and including provn of cement concrete bedding and 'P' or 'S' trap as required including connection to trap and to flush pipe, anti syphonage pipe, etc. and making good to floor complete all as specified and directed.

S&F in replacement vitreous china wash down water closet pan (Pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) with and including white plastic seat cover with aluminium hinging device complete all as specified and directed.

S&F in repairs vitreous china wash basin, white, flat back, size 450 x 300 mm including PVC connections 15mm size with PTMT nuts of length 450mm, brackets, cutting for and pinning in ends of brackets or erecting stand including CP waste coupling and PVC corrugated waste pipe complete all as specified and directed.

S&F in repairs vitreous china urinal half stall type with fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and incl 60 mm long brass screws, pointing around urinal back in white cement, PVC flush pipe and union for discharge pipe, PTMT spreader and PTMT waste coupling 32 mm bore & PVC connection pipe 450 mm long for flushing (excluding flushing cistern) complete all as specified and directed.

S&F in repairs 15 mm bore fancy type stop/ angle valves, cast copper alloy, chromium plated, fancy type (Concealed type) with long shank and cup and capstan head, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

S&F in repairs 15mm bore, fancy type, long body bib taps, cast copper alloy with capstan head, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S&F in repairs 15 mm bore long body pillar taps, cast copper alloy with capstan heads, chromium plated, fancy type, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed.

S&F in repairs for 10 ltrs capacity, PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets flushing cistern, PVC flushing pipe of suitable length and PVC connection 450 mm long complete all as specified and directed.

S&F of PVC connection 15 mm dia of length not less than 600 mm with brass fly nuts on both ends for water supply complete all as specified and directed.

S&F of sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf, 12 cm wide with chromium plated bracket guard and railing 60 cm long complete all as specified and directed.

S&F for stainless steel soap dish, any type, fixed to plugs with chromium plated brass screws complete all as specified and directed.

S&F for brass chromium plated tubular towel rail, 20 mm dia, D type, 60 cm long between flanges and fixed with screws complete all as specified and directed.

S&F in replacement 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches/floors or fixed to walls complete all as specified and directed.

S&F in replacement 75 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches/floors or fixed to walls complete all as specified and directed.

S&F of 75 mm bore PVC (SWR) bends of any radius with or without access door, fixed and jointed with solvent cement complete all as specified and direcetd.

S&F of 75 mm bore PVC (SWR) junction (single T) with access door equal or unequal, fixed and jointed with solvent cement complete all as specified and direcetd.

S&F of 75 mm bore PVC (SWR) floor trap/ multi trap, plain with ss grating including jointing with solvent cement complete all as specified and directed.

M&L for brick work with fly ash bricks, straight or curved on plan exc 6m mean radius, built in CM 1:6 complete all as specified and directed.

M&L for brick work with fly ash bricks, straight or curved on plan to any radius in half brick thick walls built in CM 1:4 complete all as specified and directed.

M&L for cement concrete 1:4:8, type D-2 ((using 40mm graded stone aggregate) as in foundations, filling and mass concrete etc complete all as specified and directed.

Surface excavation n. exc 30 cm deep and averaging 15 cm deep and getting out in hard/ dense soil complete all as specified and directed.

Taking out settled bricks/ Interlocking paver blocks of any thickness (laid flat or on edge) in path, floors, channels, kerbs, aprons, etc. (each layer) laid dry and refixing the same at same location over sand cushion complete all as specified and directed.

M&L for sand cushioning with clean dry sand for filling under floors or in foundations including watering and consolidation complete all as specified and directed.

Supply and laying 60 mm thick rubber moulded factory made chamfered edge cement concrete glossy finish paver block of M-35 grade of approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc; of required strength, thickness & size/ shape, laid in required colour & pattern over and including 50 mm thick compacted bed of river fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer and filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and directed.

M&L for 75 mm thick PCC 1:3:6 type C2 (using 40 mm graded stone aggregate) as in plinth protection, aprons, hard standing, path and like; finishing the surfaces even and smooth without using extra cement with and including making the grooves in bays n exc 2 m in length and cutting dummy joints 65 x 10 mm @ 3 m interval and at corners and filling the same with bitumen mastic 1:3 including dismantling of old concrete complete all as specified and directed.

M&L for cement concrete 1:2:4, type B-0 (using 12.5 mm graded stone aggregate) as in roof kerbs or mud stops, rounded or chamfered on edges using WPC of approved make as per manufacturers instruction complete all as specified and directed. Note: WPC shall be measured and paid separately.

M&L for 10 mm thick cement plaster in CM 1:3 over concrete surfaces, finished even and smooth without using extra cement with using WPC of approved make per manufacturers instruction complete all as specified and directed. Note: WPC shall be measured and paid separately.

M&L for preparation of newly plastered roof surfaces and applying two coats of Dr fixit roof seal classic or equivalent chemical with and comprising of the following steps:- Step-1: Marking 2 x 2 m area on roof surface. Step-2: Applying first coat on ready surface in one direction using 1.5 ltr/ 4 sqm area. Step-3: Applying second coat using 1.0 ltr/ 4 sqm after 12 hrs in perpendicular direction of first coat application.

M&L for 10 mm thick rendering cement plaster in CM 1:6 on brick/ concrete surfaces, finished even and smooth without using extra cement including taking down old plaster and raking out joints complete all as specified and directed.

M&L for 15 mm thick rendering cement plaster in CM 1:4 on brick/ concrete/ stone masonry surfaces, finished even and smooth without using extra cement with mixing water proofing compound as per manufacturer instruction including taking down old plaster and raking out joints complete all as specified and directed. Note: WPC will be measured and paid separately.

M&L 5 mm thick rendering cement plaster in CM 1:3 as on brick/ concrete ceiling surfaces, finished even and smooth without using extra cement including taking down old plaster and raking out joints complete all as specified and directed.

Supply only Integral water proofing compound complete all as specified and directed.

M&L for preparation of newly plastered surface of walls and applying two coats of oil bound distemper over a coat of 1 mm thick white cement based putty, finished even and smooth complete all as specified and directed.

Complete removal of old decorated surface of walls with and including M&L for applying two coats of oil emulsion distemper white/ tinted over a coat of 1 mm thick white cement based putty, finished even and smooth complete all as specified and directed.

M&L for preparation of newly plastered or unplastered surface of walls, soffits, facia, chajjas etc and applying two coats of exterior weather proof water based emulsion paint over a coat of compatible primer complete all as specified and directed.

M&L for preparation of old plastered or unplastered surfaces of walls, soffits, facia, chajjas and applying two coats of exterior weather proof water based emulsion paint complete all as specified and directed.

M&L for preparation of new plastered or unplastered surfaces of ceilings and applying three coats of white wash complete all as specified and directed.

M&L for prepration of old decorated surfaces of ceilings and applying two coats of white wash complete all as specified and directed.

S&F in replacement galvanised, 2 strand, mild steel barbed wire of 2.24 mm dia barbed with 2 mm dia barbs at 75 mm spacings including straining and fixing to any type of standard rails, straining bolts and securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed (each line wire to be measured) complete all as specified and directed.

Taking down copper/ aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc.for taking credit and making good disturbed surfaces of walls, floors, etc. complete all as specified and directed.

M&L for point wiring for one light / fan / bell point with multi-stranded copper conductor stranded copper conductor 1.5 Sqmm nominal cross-sectional area, single core, PVC insulated and unsheathed FRLS cable, 1100 volts grade in and including medium grade, PVC concealed conduit and conduit accessories of not less than 20 mm dia, concealed in wall/ floor etc, ISI marked with sheel metal mild steel flush box, white cover plate with frame for fixing modular switches, sockets and fan regulators etc. including PVC insulated multi-stranded copper conductor 1.5 Sq mm nominal cross sectional area single core FRLS cable as earth continuity conductor to common earth and connecting to earth dolly complete all as specified and directed at site for the following:- Note:- Cutting chase and making good will be included in the quated rates.

All as per ser item No. 85.00 here-in-before but one switch socket combination, 5/6 Amps on independent board complete.

All as per ser item No. 85.00 here-in-before but for one three pin socket outlet, 5 Amps on same board with other switches complete.

All as per ser item No. 85.00 here-in-before but for one light point controlled by 5/6 Amps, two two-way switches complete.

All as per Srl item No. 85.00 here-in-before but for one switch socket combination, 6 pin, 5/ 15 Amps on independent board with wire of size 2.5 Sqmm and 2.5 Sqmm as earth wire complete.

S&F of modular switch, two way, 6 Amps, one module, 240 volts complete all as specified and directed.

S&F of modular switch, one way, 6 Amps, one module, 240 volts complete all as specified and directed.

S&F of modular socket outlet, 2-in-1, 6 Amps, two module, 240 volts complete all as specified and directed.

S&F of modular switch, one way, 16 Amps, one module, 240 volts complete all as specified and directed.

S&F of modular socket outlet, 2-in-1, 6/16 Amps, two module, 240 volts complete all as specified and directed.

S&F of ceiling rose, 2/3 terminals, 65 x 25 mm dia poly carbonate isulated complete all as specified and directed.

S&F of modular type lamp holder insulated PVC/ polycarbonate body with back plate for conduit /batten fittings with 10 Watt LED bulb complete all as specified and directed.

S&F of modular type ceiling fan regulator, electronic step type, 240 Volts, AC 50 Hz, single pole, 100 watts, two module, flush/ socket type complete all as specified and directed.

S&F of LED tube light complete fitting 20 watts, 220 Volts, AC, decorative box type with driver, holder including LED tube light and making connection with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

S&F of LED invertor type lamp, 10 Watt, B22, CDL complete all as specified and directed.

S&F in replacement single pole and neutral sheet metal enclosure with two pin and earth, plug and socket, suitable for single phase 240 Volts with and including one single pole MCB of capacity 20 Amps having `C` charactristic, breaking capacity 10 KA including industial plug top complete all as specified and directed.

S&F in replacement sub main wiring with approved colour coding as per IS (Red, Black and Green for single phase circuits) with three single core PVC insulated FRLS cable 1100 V unsheathed with stranded copper conductor of 6.0 sqmm nominal cross section area and drawing into 20 mm external diameter rigid non metallic PVC conduit, ISI marked, medium grade inclusive of all fittings such as tees, bends, junction boxes, elbows, saddles, pipe hooks, couples, lock outs, etc. in concealed wiring system by cutting of walls (brick or stone) and making good disturbed surface of wall in CM 1:3 and PVC insulated FRLS stranded copper conductor of 6.0 sqmm nominal cross section area as earth wire complete all as specified and directed. Note: Three runs of 6.0 sqmm cable and PVC conduit pipe shall be measured as one unit length.

S&F in replacement sub main wiring with approved colour coding as per IS (Red, Black and Green for single phase circuits) with three single core PVC insulated FRLS cable 1100 V unsheathed with stranded copper conductor of 4.0 sqmm nominal cross section area and drawing into 20 mm external diameter rigid non metallic PVC conduit, ISI marked, medium grade inclusive of all fittings such as tees, bends, junction boxes, elbows, saddles, pipe hooks, couples, lock outs, etc. in concealed wiring system by cutting of walls (brick or stone) and making good disturbed surface of wall in CM 1:3 and PVC insulated FRLS stranded copper conductor of 4.0 sqmm nominal cross section area as earth wire complete all as specified and directed. Note: Three runs of 4.0 sqmm cable and PVC conduit pipe shall be measured as one unit length.

S&F in repairs sheet metal enclosure for MCB, DB, SPN, 240 Volts, 200 Amps rated bus bar, 8 way, double door enclosure made up of CRCA sheet steel, RAL 9003 powder coated, IP-54 protection, dust and vermin proof suitable for incorporation MCBs and isolators etc complete all as specified and directed. Note: MCB will be measured and paid separately.

S&F in repairs sheet metal enclosure for MCB, DB, TPN, 415 Volts, 200 amps rated busbar, 4 way, double door enclosure made up of CRCA sheet steel, RAL 9003 powder coated, IP-54 protection over and including wooden rectangle board of first class hardwood of suitable size for mounting of DB box complete all as specified and directed. Note: MCB will be measured and paid seperatly.

S&F in repairs factory made epoxy powder coated distribution board TP & N, 4 ways (VTPN MCCB DB) and space for MCCB as incomer with metal door (IP-54 protection) fabricated from CRCA sheet and fixed semi flush to wall and suitable for universal mounting and including isolated neutral bar, insulated bus bar assembly, neutral bar, standard DIN rail, earth bar and cable ties for cable management, top and bottom removable gland plates with knockouts complete all as specified and directed. Note: MCCB will be measured and paid seperatly.

S&F of MCCB, 160 Ampa, 3 polea, breaking capacity 36 KA and making electrical connections with suitable copper lugs complete all as specified and directed.

S & F in repairs MCB, SP suitable for 240 volts, AC supply 6 to 32 Amps with over load and short circuit protection and rupturing capacity not less than 10KA 'C' connection with suitable size copper lugs curve including complete all as specified and directed.

S&F of MCB, SPN, 32 Amps, 240 volts, AC with over load and short circuit protection and rupturing capacity not less than 10 KA of 'C' curve and making connection with suitable size copper lugs complete all as specified and directed.

S&F of MCB, TPN, 63 Amps, 240 volts, AC with over load and short circuit protection and rupturing capacity not less than 10 KA of 'B' curve and making connection with suitable size copper lugs complete all as specified and directed.

S&F in repairs integral LED building security light luminaire, 36 Watts of luman efficiency not less than 110 lm per watt, comprising of die cast alluminium housing enclosed with glass cover in frame, IP-66 protection suitable for voltage range 170 to 240 Volts complete fixed with and including bracket made out of GI pipe 32 mm dia (light grade) 1 metre long with MS clamps, nuts, bolts, washers and making connection with three core cable 1.5 sqmm from ceiling rose to fittings complete all as specified and directed.

S&F of exhaust fan, heavy duty, rust proof steel body, 230 Volts AC, single phase of size 300 mm sweep with blades, frame and louvers and all necessary fittings with and including drilling of hole and repair of disturbed surfaces complete all as specified and directed.

S&F of 1200 mm sweep ceiling fans complete with blades, down rods and accessories, 230 Volts, min air delivery 210 CFM with service value 6.00 BEE, five star rated with brushless direct current motor (BLDC) without remote controller complete all as specified and directed.

S&F of 400 mm sweep wall mounted fan, metal body with plastic blades, 1350 RPM, 55 watts, 240 V, 50 Hz, air deliver 65 m³ per minute and three Nos of speed controlling complete all as specified and directed.

M&L of earthing complete with galvanised steel earth plate electrode size 600 x 600 x 6 mm thick burried directly in ground vertically to a depth not less than 2.25m deep below normal ground level with top edge of earth plate not less than 1.5m deep below normal ground level and connected to and including GI earth lead wire 4 mm dia by means of bolts, nuts, check nuts & washers of galvanised iron and connected to test point all as shown in electrical plate No 3 of SSR Part-I (2009) including excavation and earth work in any type of strata available at site, PCC 1:3:6 type C-1 (using 20mm graded stone aggregate) earthing chamber, precast RCC cover 50 mm thick in cement concrete 1:2:4 type B-1 (using 20 mm graded stone aggregate) duly reinforced with welded steel wire fabric (XPM) weight not less than 4 kg/sqm, funnel, GI watering pipe of 20 mm bore medium grade, wire mesh and lugs, GI protection pipe of 15 mm bore, light grade up to 7.5 metre long and testing on completion complete all as specified and directed. Note: GI earth wire and protection pipe upto 7.5 metreis included in quoted rate.

Excavation in trenches n. exc. 1.5 mtr in wide and n. exc. 1.5 mtr in depth for laying of underground cable and getting out in hard/dense soil complete all as specified and directed.

Returning, filling in excavated soil in trenches including spreading, leveling, watering and well ramming in layers n. exc. 25 cm thick complete all as specified and directed

Removing of excavted soil to a distance n. exc. 50 mtr and deposited where directed at a level not exceeding 1.5 mtr above the starting point complete all as specified and directed.

M&L for sand filling with clean dry fine sand unwashed including gently punning around cables in trenches for cable protection (8 cm below cable & 15 cm above cable) complete all as specified and directed. Note:-Compacted/punned thickness shall be measured & paid.

Supply and laying of factory made precast concrete cable cover, class LV, Type I, flat, size 250 x 150 x 40 mm for cable protection cover laid flat and dry in trenches over the cable perpendicular to the direction of cable complete all as specified and directed.

Supply, laying, connecting and testing LT XLPE insulated, screened, PVC bedded, armoured, heavy duty cable with aluminium conductor of size 35 Sqmm, 3.5 core, 1100 volts grade, laid in trenches, passing through pipes/ducts, etc. complete all as specified and directed. Note: Excavation, earth work and pipe / sand / bricks for cable protection shall be measured and paid for separately.

S&F of 40 mm GI tubing light grade (as per IS -1239) with all fittings as required for passing through cables under floors, along the wall/ pole, etc; complete all as specified and directed.

S&F of 20 mm bore GI tubing medium grade with all necessary fittings and fixed complete to wall and ceiling or laid in floors complete all as specified and directed.

S&F of Gun-metal gate valves of size 20 mm with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

S&F of rotational moulded polyethylene water storage tanks, 3 layers (cylindrical vertical with closed top) of capacity 500 litres, hoisted including all fittings as required and fixed in position complete all as specified and directed.

S&F of 20 mm bore float valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for pipes in water tank and fixed complete all as specified and directed.

Deduct Schedule of credit (calculation will be done off line) Rs. 63317.00