PROVISION OF AMPHIBIOUS TRAINING EQUIPMENT STORE ROOM AT NARIYAL BAGICHA TOILET BLOCK FOR GUARD AT NARIYAL BAGEECHA AND NEAR DINING HALL OF OFFR TRANSIT ACCN AT BRICHGUNJ MIL STN PORT BLAIR UNDER GE BRICHGUNJ

Amount

Surface dressing not exceeding 15cm deep and getting out in hard/dense soil complete all as specified and directed

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in hard / dense soil complete all as specified and directed

Excavating in trenches, n exc 1.5 m wide and n exc 1.5m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sqm on plan and n exc 1.5 m in depth and getting out Soft/loose Soil complete all as specified and directed

Returning filling including spreading, levelling, watering and well ramming in layers n.exc 25cm complete all as specified and directed

Removing excavated soil to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and directed.

Material & labour Filling under floors or in foundations including watering and consolidation complete all as specified and directed. Note: approved earth obtained from excavation shall be used for filling

Material & Labour for Moorum/Red Bajri in Filling in floors or pavings, laid in layers n exc 15cm thick, spread, levelled and rammed including watering and complete all as specified and directed

Material & Labourfor hard-core of gauge not exceeding 63 mm of broken granite stone, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface complete all as specified and directed

Material & labour for treating the bottom & sides of excavation @ the rate of 5 Lit of anti termite emulsion per sqm of surface area complete all as specified and directed

Material & labour for Anti termite treatment on top of earth filling @ 5 lits of anti termite emulsion per sqm complete all as specified and directed

Material and labour for Cement concrete 1:3:6 Type C-2 (using 40mm grade stone aggregate) to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested, for 110mm bore drain pipes complete all as specified and directed

Material & labour for 75mm thick Cement concrete in (1:3:6) Type C1 using 20mm graded stone aggregate as in plinth protection and finished even and smooth with using extra cement complete all as specified and directed.

Material & labour for 40mm thick Damp proof course in cement concrete 1:2:4 Type B0 (using 12.5mm grade stone aggregate) to horizontal or vertical surface including necessary formwork complete all as specified and directed

Material & labour 100 mm thick PCC 1:3:6 Type C-2 (using 40 mm graded granite stone aggregate) for Sub Base complete all as specified and directed

Material & labour for 75mm thick PCC 1:4:8 Type D2 (40mm graded aggregate) as sub base complete all as specified and directed

Material & labour 75mm thick PCC(1:2:4) Type B2 using 20mm graded stone aggregate as in flooring finished even and smooth using extra cement complete all as specified and directed

Material and labour Plain Cement Concrete 1:4:8 Type D2 (using 40 mm graded granite stone aggregate) in foundations, filling and mass concrete complete all as specified and directed

Material and labour for precast cement concrete solid block masonry with solid blocks using PCC 1:3:6 Type C1 using 20mm graded stone aggregate n.exc 10cm in width and setting in cement mortar (1:4) etc complete all as specified.

All as per item No 18 here in before but exc 10cm in width

All as per item No 19 here in before but setting in cement mortar 1:6

Material & labour for Reinforced cement concrete M30 (design mix) in foundations, including rafts, footings, foundation beams, plinth beams, bases for columns, etc, basement slabs, under reamed piles and mass concrete complete all as specified.

Material & labour Reinforced cement concrete (design mix) M-30 grade using 20mm graded aggregate) like Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed

Material & labour for Reinforced cement concrete M30 (design mix) in columns, pillars, piers, posts and struts etc complete all as specified and directed

Material & labour for Reinforced cement concrete M30 (design mix) in Slab supported on walls, beams and columns in floors, roofs, landings, balconies canopies, deck slabs and in shelves and the like complete all as specified and directed

Use and waste Form work to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floors and roofs n.exc 20cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work all exceeding 10cm wide and n.exc 20cm wide with rough finished surfaces complete all as specified and directed

Use and waste form work to sides of rough finished concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits if any of foundation and plinth beams and similar work vertical or to batter complete all as specified and as directed by Engineer in Charge.

Use and waste form work to sides of Pillars, posts, struts, piers, columns and sanctions complete all as specified and directed

Use and waste Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. complete all as specified and directed

Use and waste form work to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick(Horizontal or sloping) complete all as specified and directed

Material & labour for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed

All as per item No 30 here in before, but 6mm to 8mm dia

Material & labour for TMT bars 5mm dia and over upto and incl 10mm dia in stirrups, spacers, and binders in reinforcement cut to length, bent to shape required including cranking hooking ends and binding with mild steel wire complete all as specified and directed

Material & labour for Rendering 15mm thick with cement plaster in CM 1 :4 on concrete surfaces mixed with WPC @ 3% by weight of cement complete all as specified and directed by the Engineer-in-Charge. Note: WPC shall be measured and paid separately

Material & labour for rendering 10mm thick on fair faces of brick/concrete surface in CM (1:6) finished even and smooth without using extra cement complete all as specified and directed.

Material and labour for 15mm thick external rendering in two layers of 5mm thick in CM (1:4) mixed with water proofing compound (water proofing compound shall be @3% weight of cement) over and including a coat of 10mm thick in CM (1:6) over brick or concrete surfaces finished even and fair. Note: Supply only WPC will be measured and paid separately

Material & labour for 5mm thick rendering on fair faces concrete surface of ceiling in CM (1:3) finished even and smooth without using extra cement complete all as specified and directed

Material & labour 10mm thick cement plaster in cement concrete (1:3) on top of roof slab complete all as specified and directed

Supply only water proofing compound conforming to IS-2645 1975 complete all as specified and directed

Material & labour for preparation of new plastered wall surfaces and applying two coats of oil bound distemper over a coat of primer including one layer of wall care putty complete all as specified and as directed by engineer-in-charge.

Material & labour for oil bound distempering two coats over a coat of alkali resistant priming paint including preparation of new plastered or unplastered surfaces of wall complete all as specified and directed by Engineer - in -Charge.

All as per item No 40 here in before, but on ceiling

Material & labour for two coat of weather proof exterior acrylic emulsion paint with anti-fungal property over a coat of primer and a coat of external wall putty on newly plastered wall surfaces including preparation of surfaces etc complete all as specified and as directed.

Material & labour for preparation of new or previously untreated steel surfaces & applying a two coats of synthetic enamel paint over a coat of red oxide primer over 10cm in width or girth, not otherwise described.

Material & labour for for preparation of new or previously untreated wood surface of any description, exceeding 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified and as directed

Material & labour for Plates (Plain or Chequered) channels, square or notched (Ordinary and counter sunk) forming holes, without any attachment of Fe 290 (Gde E-165) complete all as specified and as directed by Engineer in Charge.

Material & labour tubular trusses using Fe 410 -W (GdeE- 250) quality A (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc complete all as specified and as directed

Material & labour Mild Steel works for wind ties for roof & supporting tie for valley gutter including securing bolts including all necessary drilling, bolting or riveting, welding etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified and as directed

Material & labour Mild steel screw bolts (machine made) with hexagonal or square heads with dia of neck 11 to 15 mm at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc 10 cm long and n.exc 15 cm long all as specified and directed by engineer in charge

Supply and fix Pre- painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self-tapping screws all as specified.

Supply and fix Pre- painted galvalume aluminium zinc coating GI based Plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self-tapping screws all as specified.

Material and Labour false ceiling with aluminium grid work (size of grid 605x605mm) with 35x25x1.5mm main tee and 25x25x1.4mm, cross tee and wall angle and suspended with 3.15mm dia, GI wire, hooked to roof with needful adjustment bolts at an interval of 1.20m, centre to centre staggered and board with Eco board, decorative type, size 600x600x4mm thick, finished with two coats of oil bound distemper over a coat of primer complete all as specified and as directed by Engineer-in-Charge.

Material and Labour for apply water proofing treatment with the following specifications complete all as specified and as per manufacturer’s instructions:- (i) Rendering 10mm thick in CM 1:4 on concrete surfaces mixed with water proofing compound @ 3% by weight of cement as leveling course (ii) Apply a coat of hot blown bitumen 85/25 @ 1.20 kg/sqm over a coat of bituminous primer @ 0.3 ltr per sqm. (iii) Laying APP membrane (STP Aquashield or equivalent) weighing not less than 3.5Kg/sqm, reinforced with polyster non woven fabric (weighing not less than 150 gms/sqm) with 100mm over laps both longitudinally and transversally and overlaps shall be sealed by torch, membrane shall be taken to the parapet through fillet and shall be tucked in inside after a height of 300 mm. (iv) Apply one coat of hot blown bitumen 85/25 @ 1.2 kg/sqm over the membrane. Note:- Water proofing compound shall be measured and paid separately)

Material & labour Non skid ceramic tiles each tile area (sqr/rectangle) exc 0.06Sqm but not exceeding 0.11Sqm tile thickness 7 to 8 mm, in floors etc set and joined in neat cement slurry and pointed in white or coloured cement to match incl Screed bed or bedding layer with 20 mm thick, cement mortar 1:6 for laying floor finishes all as specified .

Material & labour for Coloured ceramic tiles joint free area exc 0.11 Sqm but exc 0.18 Sqm as in floor, set, jointed and pointed in white or coloured cement to match over screed bed in 20 mm thick, cement mortar 1:6, all as specified and directed

Material & labour Glazed ceramic tiles coloured 350x 250x5/ 450X 350X 7mm thick on vertical surfaces such as skirting, dado etc set and jointed in neat cement slurry and pointed in white or coloured cement to match incl 10mm thick in cement mortar 1:3 as backing coat for fixing dado tiles all as specified.

Material & labour Glazed ceramic tiles coloured 300x 200x5 to 6mm thick on vertical surfaces such as skirting, dado etc set and jointed in neat cement slurry and pointed in white or coloured cement to match incl 10mm thick in cement mortar 1:3 as backing coat for fixing dado tiles all as specified.

Material & labour for glazed, polished chequered cement concrete tiles 300 x 300mm x 25mm thick, set, jointed and pointed in neat cement slurry, including creed bedding layer in 20 mm thick, cement mortar 1:6, in flooring, complete all as specified and as directed by Engineer-in-Charge.

Material & labour for Granite (of any type) tiles 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete including 20mm screed bed cement concrete 1:6 complete all as specified and as directed

Supply and fix 2nd class hardwood, plain, solid, straight chowkats and frames wrought, framed, rebated on the solid, rounded or chamfered, put together with glue, pinned at joints complete all as specified and as directed.

Supply and fix 2nd class hard wood 35 mm thick, plain, framed, paneled shutter factory made ( any number of panels) with panels of timber flat on both sides ( feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers, the sizes of members of shutters shall be specified and as directed by Engineer-in-Charge

Supply and fix 2nd class hardwood 35mm thick glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut and mitred beads of securing glass, gauze etc and fitted to chowkats complete all as specified and directed.

Supply and fix Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S Square tube, supplying & fixing in opening as per specification & drawing

Supply and fix Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded plain colour PVC `C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S frame welded/ sealed to the stiles, & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawing.

Material & labour for aluminium anodised sections(Minimum thickness of anodisation 15 micron) for partitions, window and door with frame and shutters fully or partly glazed, side hung type (two numbers glazed and gauzed ) without sash bars , with panel inserts of sheet glass, gauzes including necessary jointing cleats, glazing clips, rubber beading, neoprene packing, aluminium snap beading screws, aluminium fittings such as handles, aluminium butt hinges aluminium tower bolts, the size of aluminium section shall be all as specified and as directed by engineering charge ( Notes: (i) Supply only panel inserts of glass / gauze will be measured and paid separately as supply only.(ii) Weight of aluminium sections only shall be accounted for payment purpose. However unit rate quoted shall be deemed to include for cost of rubber beading, glazing clips neoprene packing, fittings such as handles, butt hinges, tower bolts and fixing only of panel inserts of glass/ particle board/ gauge, etc(iii) Weight of aluminium handles, butt hinges& tower bolts shall not be accounted for payment purpose)..

Material & labour for powder coated aluminium sections(Minimum thickness of powder coating 50 micron) for partitions, window and door with frame and shutters fully or partly glazed, side hung type (two numbers glazed and gauzed ) without sash bars , with panel inserts of sheet glass, gauzes including necessary jointing cleats, glazing clips, rubber beading, neoprene packing, aluminium snap beading screws, aluminium fittings such as handles, aluminium butt hinges aluminium tower bolts, the size of aluminium section shall be all as specified and as directed by engineering charge ( Notes: (i) Supply only panel inserts of glass / gauze will be measured and paid separately as supply only.(ii) Weight of aluminium sections only shall be accounted for payment purpose. However unit rate quoted shall be deemed to include for cost of rubber beading, glazing clips neoprene packing, fittings such as handles, butt hinges, tower bolts and fixing only of panel inserts of glass/ particle board/ gauge, etc(iii) Weight of aluminium handles, butt hinges& tower bolts shall not be accounted for payment purpose).

Supply only 4 mm thick sheet glass ordinary quality and glazing with rubber packing around the glass, in squares not exceeding 0.50 sqm in each pane complete all as specified and as directed.

Supply only aluminium alloy wire mesh 0.45 nominal dia of wire and average width of aperture 1.40mm fixed with aluminium wire staples complete all as directed by Engineer-in-Charge.

Supply and fix 4 mm thick sheet figured glass and glazing with rubber packing around the glass, in squares exceeding 0.50 sqm in each pane complete all as specified and as directed.

Supply & fix aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40 mm complete all as specified and as directed

Supply and fix 150mm long extruded aluminium alloy anodised handles fabricated type complete all as specified and as directed

Supply and fix Aluminium anodised barrel tower bolt of extruded section of size 150mm long complete all as specified and as directed

Supply and fix Aluminium alloy anodised sliding door bolt with hasp, staple (bolt type) 300 mm long and fixing clips to sheet cast or extruded sections and fixing bolt or cast aluminium alloy complete all as specified and as directed

Supply and fix Aluminium anodised butt hinges 100 mm long extruded aluminium, alloy with galvanised mild steel hinge pin, type C-22

Supply and fix Butt hinges, Size of hinge 100mm extruded brass, with mild steel hinge pin, bright polished and fixed, type B-21 complete all as specified and as directed

Supply and fix Towel rail 600mm long & including Chromium plated brass screws & wooden / plastic cleats (Minimum weight 190gms) complete all as specified and as directed

Supply and fix of brass, chromium plated toilet paper holder fixed to walls with chromium plated brass screws complete all as specified and as directed

Supply and fix stainless steel, towel rack, 600mm long with 10mm dia four rods and 20mm dia four hooks complete all as specified and as directed

Supply and fix of PTMT gratings 125mm dia, complete all as specified and as directed by Engineer-in-Charge

Supply and fix repairs chromium plated hand shower (health faucet) 1 meter, with PVC tube with wall hook, complete all as specified and as directed by Engineer-in-Charge. (Make : Jaquar cat No ALD-CHR-593 or equivalent)

Supply and fix wash hand basin of size 375X475X130mm including all fittings and bracket etc of Jaquar Cat No. JDS-WHT-25907 or equivalent complete all as specified.

Supply and fix vitreous China wash hand basin, 'OVAL TYPE' 545x 545x185 mm including with single tap hole fixed in granite including chromium plated CP waste coupling, chain and plug, waste fitting, union and waste pipe 32 mm dia of required length and all necessary 450 mm long outlet and inlet PVC connectns pipe with PTMT check nuts complete all as specified and as directed. Make: Jaquar cat Part No. FSS-WHT-29601 or equivalent

Supply and fix vitreous China wash hand basin of 590 X 450mm (CAT no.324RHINE of make Neycer or equivalent of Parryware/Hindustan), including 15mm dia swan neck fancy type chromium plated pillar tap (Cat No.G0203A1, Make - Parryware or equivalent), CP waste coupling, chain and plug, waste fitting, union and waste pipe 32mm dia, brackets, PVC connection 450mm long with check nut, including cutting for and pinning in ends of brackets or erecting stand, complete all as specified and as directed by Engineer-in-Charge.

Supply and fix of 10 ltr capacity, PVC flushing cistern, white, syphonic action type, low level, with inlet, ball valve float and handle, PVC flush pipe, brackets etc including taking down unserviceable flushing cistern etc, complete all as specified and as directed by Engineer-in-Charge.

Supply and fix vitreous China urinal, half stall type complete including waste pipe, flush pipe & providing and fixing plugs, bedding urinal against wall in cement mortar 1:2 securing urinal to plugs with and including 60mm long brass screws pointing around urinal back in cement etc, and including connection to flushing pipe and outgoing pipes fixed complete all as specified and as directed by Engineer-in-Charge.

Supply and fix vitreous china EWC model CASCADE type of size 640 x 360 x 690 mm in approved colour all as specified and directed as per ISI mark. Make : Jaquar cat Part No. SLS-WHT-6851P or equivalent in Neycer, Johnson.

Supply and fix water closet pan (pedestal pattern) white, os size 650X360X800mm of Jaquar Cat. No. OPS-WHT-15751 and with flushing Cistern & fittings of Jaquar Cat.No. ZPS-WHT-15201 complete all as specified

Supply and fix in Vitreous China wash down water closet pan (pedestal pattern), white including connection to trap and to flushing pipe, anti syphonge pipe etc, including making good the floor complete all as specified and as directed.

Supply and fix Chromium plated 125mm shower roses with or without swivel joints, any size, including fixing to steel pipe or union complete all as specified and as directed

Supply and fix of Bib tap cast copper alloy chromium plated 15mm dia with fancy type screwed down screwed for iron pipe or brass ferule etc complete all as specified and as directed by Engineer-in-Charge

Supply & Fix 20mm dia ball valve high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed, minimum weight 142 gms, complete all as specified and directed by Engineer-in-Charge

Supply and fix for 20 mm dia bore gun metal , globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed.

Supply and fix of stop valves cast copper alloy, screwed down, high pressure, with fancy type, chromium plated, screw both ends for 15mm dia iron pipe or for union and fixed.

Supply and fix of PVC connection 15mm size with CP brass Nuts of length 450mm complete all as specified and as directed by Engineer-in-Charge

Supply and fix 75 mm dia PVC (SWR) floor trap plain with grating including jointing with solvent cement

Supply and fix PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement

Supply and fix 25 mm dia ball valves high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed, complete all as specified and as directed

Supply and fix 25 mm bore Gun Metal gate valve with iron wheel head ISI Marked screwed both ends suitable for GI tubing complete all as specified and directed

Supply and fix PVC (SWR) bends any radius 110mm bore complete all as specified and as directed

Supply and fix PVC (SWR) vent cowl 110mm bore complete all as specified and as directed

Supply and fix PVC (SWR) pipes 110 mm dia double socketed in any length with rubber ring joints fixed to walls complete all as specified and as directed

Material and Labour for 110mm PVC (SWR) pipes single socketed in any length with rubber ring joints, laid in trenches or in floors

Material & labour for 20 mm bore unplasticised PVC pipes of pressure rating 10 Kgf/Sqcm fixed complete to walls, ceilings or in floors etc any type of pipe all as specified and as directed.

Material & labour for 15 mm bore unplasticised PVC pipes of pressure rating 10 Kgf/Sqcm fixed complete to walls, ceilings or in floors etc any type of pipe all as specified and as directed.

Supply and fix 25 mm bore GI tubing medium grade laid in trenches / floor or fixed to wall in any length with screwed and socket joints together with all galvanised GI fitting such as sockets, bends, elbows, tees, reducers, unions, jointing materials etc and pressure testing, washing out complete all as specified and directed

Supply and fix rotational moulded polyethylene water storage tanks 500 ltrs capacity (cylindrical or vertical with closed top) hoisted and fixed in position, complete all as specified and directed by Engineer-in-Charge

Supply and fix rotational moulded polyethylene water storage tanks 1000 ltrs capacity (cylindrical or vertical with closed top) hoisted and fixed in position, complete all as specified and directed by Engineer-in-Charge

Material & labour for cutting existing 50mm GI line and making branch connection of 40 mm dia GI line complete all as specified and directed

Material & labour for point wiring as per colour coding with 1.5 sqmm FRLS PVC insulated unsheathed stranded copper conductor cable drawn through in and including 19 mm thick rigid non metallic PVC concealed conduit medium quality including new sunken terminal boxes duly epoxy painted and 3mm thick plastic laminated sheet top cover and continuity earth wire PVC insulated copper conductor standard unsheathed of size 1.5sqmm including Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills sunshades, shelves, lintels, etc.; and cutting chases for concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth in brick wall for One light/E/fan point controlled by one switch complete all as specified and as directed by Engineer-in-Charge.

All as per item No 109 here in before, but One fan point controlled by one switch and one regulator

All as per item No 109 here in before, but One three pin 5 Amp switch socket on same board

All as per item No 109 here in before, but One three pin 5 amp switch socket outlet multi-purpose on independent board

Supply and fixing in replacement of switch piano flush type single pole one way 5 Amp all as specified and directed.

Supply and fix switch socket outlet 3 & 2 pin (mult pin) 5 amps flush/box type, complete all as specified and as directed by Engineer-in-Charge

Supply and fix ceiling rose surface Bakelite 65 x 50 mm 3 terminal, complete all as specified and as directed by Engineer-in-Charge

Supply and fix fan speed regulator, electronic suitable for single phase AC, 240 volts, 50 Hz,100 watts, complete all as specified and as directed by Engineer-in-Charge Make:-Anchor/Havells/Bajaj

Supply and fix metal enclosure distribution board SPN, 4 way 240 volts, with 200 amps rated bus bar, with IP 42 protection and double door, suitable for mounting MCBs, including taking down old MCB/DB, complete all as as specified and as directed. Make- Havells or equivalent Legrand/L&T/Schneider

Supply and fix MCB single pole, 240 volts, 5 to 32 Amps, all as specified and as directed. Make : Havells or equivalent Legrand/L&T/Schneider

Supply and fix MCB single pole and neutral, 240 volts, 6 to 32 amps, complete all as specified and as directed by Engineer-in-Charge

Supply and fix metal enclosure distribution board SPN, 2 way 240 volts, with 200 amps rated bus bar, with IP 42 protection and double door, suitable for mounting MCBs, Complete all as as specified and as directed by Engineer-in-Charge. Note:- Incoming & Outgoing connections from the DB shall be provided with proper lugs/thimbles etc...

Supply, lay, test and commissioning underground XLPE insulated and PVC sheathed, armoured heavy duty underground cable, suitable for earthed system, laying in trenches/duct sleeving through pipe in duct, ISI marked with aluminium stranded conductor 1100 volt grade of cross section area 2 Core 6 sq mm Complete all as as specified and as directed

Supply & lay cable protection pipe of HDPE double wall corrugated (DWC) incl couplers, bends etc of size 50 mm OD and ID 38mm confirming to IS 14930 -II and ISI Marked all specified and directed.

Supply and fixing energy efficient LED Smart bright batten 22 watt fitting 4ft in length nano diffuser technology to ensure minimum loss in light transmitted, long life of over 30000 hours including lamp and connecting with twin core sheathed cable from fitting to ceiling rose all as specified and as directed. Make : Philips Cat No BN021C LED20S PSU CDL/NW GR or eqvt in make of Bajaj/Wipro.

Supply and fix New generation energy saving & envoi mental friendly long life versatile pressure dia cast aluminium IP65 road way luminaire with high power 25 w LEDs as light and electronic driver complete with necessary brackets (made out of 25 mm bore GI light grade pipe approx. 0.6 M long) nuts, bolts etc to be fixed as on walls complete as directed. Make: Philips Cat No BRPO20 LED HP/CW 240 V 25 w or equivalent model of Wipro / Havells

Supply and fixing energy efficient LED Smart bright batten 22 watt fitting 4ft in length nano diffuser technology to ensure minimum loss in light transmitted, long life of over 30000 hours including lamp and connecting with twin core sheathed cable from fitting to ceiling rose all as specified and as directed. incl taking down old unsv light fitting. Make : Philips Cat No BN021 LED 25S 4000 PSU GR S1 or eqvt in make of Bajaj/Wipro/Crompton.

Supply and fixing energy efficient LED Smart bright batten 10 watt fitting 2ft in length nano diffuser technology to ensure minimum loss in light transmitted, long life of over 25000 hours including lamp and connecting with twin core sheathed cable from fitting to ceiling rose all as specified and as directed. Make : Philips Cat No BN021C LED10S -6500 PSU GR S1 or eqvt in make of Bajaj/Wipro/Crompton.

Supply and fix ceiling fan suitable for working on AC 230 volts, 50 Hz,1200 mm sweep 5 star rating with down rod and canopy colour of milky white including suitable fan hook anchor fastener for fixing of fan on ceiling complete all as specified and as directed.

Supply and fix ventilating fan Celso suitable for on working of AC 230 V ,50 Hz 200 mm sweep ,incl louvers complete all as specified Make: Havells HSN code 8414 or equivalent in Crompton/Orient

Material & labour for sub main wiring complete with two runs of 4 Sqmm FRLS single core PVC insulated unsheathed single core cable 1100 volts grade, multistranded with copper conductor (ISI Marked) drawn through and including PVC Casing and caping and all accessories fixed to wall/ roofs/ floors etc with one run of 4 sqmm FRLS single core multistranded copper conductor as earth continuity conductor, including dismantling unserviceable sub main wiring including accessories, complete all as specified and as directed by Engineer-in-Charge. Note : (1) Two runs of cable one run of Casing and caping & one run of earth continuity conductor shall be measured as one running metre.

Material & labour for earthing complete with galvanised steel earth plate electrode 60 x 60 cm x 6 mm thick buried directly in ground ( earth pit not less than 2.25 M deep below ground level) with top edge of the plate not less than 1.5 Meter below normal ground level connected to GI wire 4 mm dia by means of bolts, nuts , check nuts and washers of GI and GI tubing 20 mm bore light grade for earth lead protection up to main earth test point and including concrete pit in PCC (1:3:6) Type C1 pre cast RCC (1:2:4) Type B1 cover slab 54 x 54 x 5 cm with one handle for lifting made out of 8 mm dia MS bar, wire mesh, 20 mm bore GI tubing (LG) for watering, charcoal or coal and salt in alternate layers including excavation earth work complete all as specified and directed electrical plate No. 3 of SSR part - I

Hindustan Traders

T.THIYAGARAJAN

M/s Kamal Electrical

Ravi Enterprises