MS Structure for AC Plant Room near Ward Block,ACTREC

Amount

EXCAVATION -Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth with inthe ACTREC campus, levelling including all lead and lift, as directed by Engineer-incharge.

SOLING: Providing & laying rubble stone soling using spotless stones below floors roads/pavements etc. mechanically / manually consolidated thickness as specified below with stones vertically handset interstices packed with smaller stone chips, binding with murrum & sprinkling water for proper consolidating and finishing to required levels in quantities as and when required etc. complete all as directed by the Engineer-in-Charge.

BACK FILLING WITH SOIL/MURRUM : Filling under floors with available earth / murrum/debris or brought from outside sources spreading in 200mm thicklayer, watering consolidating to 150mm thickness and finished to desired levels etc. complete. (disposing/taking away the debris outside the premises & diposing as per the guidelines of statutory authorised, complete as directed and instructed

PLAIN CEMENT CONCRETE:(PCC)-M-15 Plain cement concrete using graced stone aggregate of 20mm / 40mm max. size including consolidation using vibrator & needle if required finishing, curing, form work shuttering, centering etc. complete all as per specification and in quantity as & when required by the Engineer-in-Charge,

REINFORCED CEMENT CONCRETE: (RCC-M-25-RMC) Ready Mix Concrete in Reinforced cement concrete of specific grade grade using graded stone aggregate of 20mm max. size including consolidation with vibrator & needle of required capacity, centring, shuttering, scafolding, de-shuttering, curing in floors, lintels, columns, footings, roofs, challjas, walls etc complete as directed and instructed by Engineer-in-charge.

REINFORCEMENT: Reinforcement for reinforced cement concrete at all floors and levels including supplying cutting bending fixing and binding in position with 1.6mm dia soft drawn GI annealed binding wire including cost of binding wire labour etc. complete all as per specifications and as directed by the Engineer-in-Charge. With high yield strength deformed bars (TMT bars) & MS round bars, placing ready made cover blocks complete as directed and insturcted by engineer-in-charge.

BRICK WORK: Brick work at all floor level with cement mortar 1:4 using well burnt locally available bricks of approved quality including scaffolding, raking out joints above ground level simultaneous and as directed by engineer in charge. In foundation & plinth drain walls chambers & superstructure of all floor levels.

GI Chain link mesh : Providing and fixing G.I. chain link fabric fencing of required width in mesh size 50x50 mm including strengthening with 20x4 mm flat with nuts, bolts and washers as required complete as per the direction of Engineer-in-charge.

Steel worjk in Built up sections like Angles, T, channel etc Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. all inclusive of scafolding for erection, wastage, safety precaution etc comple as directed and instructed by E-I-C.

Providing and fixing roofing consist of 1.2 mm thick galvanized steel deck sheet confirming to IS 277:1992 used as permanent shuttering over which MS wire mesh 3mm laid at 100x100 mm grid including edge trim covered with concrete. This metal deck will be supported on structural steel beam with shear studs. (Structural steel like Beam,column, joists etc. & concrete of different grade as per design will be paid separately), with necessarry support at the time of pouring the concrete.

CORRUGATED./PLAIN : PPGI SHEET: 0.8MM-Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.60 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerin- charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape including crimping wherever required. complete as directed and instructed.

Rolling shutter+Grill+Gear Supplying and fixing rolling shutters of approved make, made of required, size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters. with grill made of MS bars and flats of required height and width of plant room. Meachanical operation with handle and gear/ball bearing arrangment for smooth handling while opening & closing of rolling shutter, complete as directed and instructed.

SAND FACED CEMENT PLASTER: Sand faced cement plaster 20mm thick in two coats over exterior & internal masonry and concrete surfaces with base coat in cement mortar 1:4, 12mm thick and finishing coat in cement mortar 1:3 8mm thick final rendering at all floors and level in quantities as required at site including double scaffolding upto 20' height wherever necessary including hacking of concrete surfaces curing etc. complete all as directed by the Engineer-In-Charge. (Disposing/Taking away debris outside the premises & disposing as per the instruction of Engineer -in charge if required is also in scope) curing complete as directed and instructed.

KOTA STONE FLOORING: Kota stone flooring / dado / skirting at all floors and levels using 25mm to 30mm thick hand cut/machine cut mirror polished kota stone slabs laid over 20mm thick cement mortar CM-1:4 bedding as specified below close jointed and pointed with matching slurry of cement finished to levels or slope or plumb in quantities as required at site for new work and or repairs to old flooring / dados / skirting including curing etc. complete all as directed by the E-I-C.

Terrace water proofing with laying brick bat coba laid on CM 1:4 with waterporing compound, to required slope, finishing top with CM 1:3 with waterproof compound, making false marking with threat at 300 x 300 size icluding flashing, rain water dips, curing with ponding etc. The waterproofing compound shall be added as per manufacturer's specification.

Rain water pipe 100 mm dia with fitings :- P.V.C. PIPES:Providing, laying, jointing, fitting, testing heavy quality P.V.C. pipes of Prince, Supreme etc. make & of required dia including all fittings required as per site requirement & laying the same at any floor levels including scaffolding all jointing materials & clamping in wooden blocks if required etc. complete as directed & specified by Engineer-In-Charge.

EXTERNAL PAINTING-Scrapping by wire brush & cleaning existing surface. Providing and Applying 100% external emulsion grade paint two coats paint of approved make,Inclusive one coat of primer before painting and as per manufractures specifications to the required approved colour scheme at sand faced smooth plaster new wall or old wall surface area etc Inclusive of Scaffolding, Dust Cleaning by using jet water pressure system on old painted surface / new surface area. Crack Filling, Labour Charges with adhering to saftey measures during the painting work, ( Saftey Belt, Helmate Etc) complete Job as directed by Engineer-In-Charge.

Painting wood/steel work/plaster surface with two coats of SYNTHETIC ENAMEL PAINT of approved shade & make over one coat of approved wood/steel primer including preparing surfaces, filling with putty wherever required, scaffolding & cleaning cost of all materials, labour, all as per drawing, specifications and as directed by Engineer Incharge etc. complete.

B L ENGINEERING

SHREE MAHALAKSHMI ENTERPRISES

JAYLAXMI ENTERPRISE

B G CONSTRUCTIONS

G-TECH CONSTRUCTION & FABRICATORS