WELCOME MAINTENANCE TO OFFICERs/JCOs/ ORs MD ACCN AND REPAIR/REPLACEMENT TO JOINERY IN JCOs/ ORs MD AND OTM ACCN AT K AREA AND SF ACCN SEC 28/29D UNDER GE CHANDIGARH.

Taking down Cement plaster or cement lime plaster on brick or stone walls including raking out joints, hacking for key & scrubbing down with water etc complete all as specified and directed by Engineer-in-Charge.

Demolition of cement concrete (reinforced) (reinforcement cut as required to facilitate demolition) as in roofs, floors (other than ground floors) beams, slabs, staircases, landing, chajjas, chimney in kitchen and similar suspended work complete all as specified and directed by Engineer-in-Charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed by Engineer-in-Charge.

Taking down chowkhats with shutters (without taking off shutter from frame) n exc 1.5 Sqm each with mongry including Cutting holes into through brick wall and making good to dismantled portion in CM (1:3) or PCC (1:2:4) complete all as specified and as directed.

Taking down chowkhats with shutters (without taking off shutter from frame)exc 1.5 Sqm but n exc 4 sqm each with mongry including Cutting holes into through brick wall and making good to dismantled portion in CM (1:3) or PCC (1:2:4) complete all as specified and as directed.

Taking down shutters of any description not exc 1 sqm each and removing from the site complete all as specified and directed by Engineer-in-Charge.

Taking down shutters of any description exc 1 sqm each but not exc 2 sqm each and removing from the site complete all as specified and directed by Engineer-in-Charge.

Dismantling Stone slabs and tiles/paver block of any description or thickness in floors, aprons etc, removing rubbish off the premises complete all as specified and directed by Engineer-in-Charge.

Dismantling of cast iron pipe/ PVC drain pipes/PVC (SWR) pipe etc, 110mm jointed in cement mortar and taking out of trenches and wall, if required complete all as specified and directed.

Dismantling of cast iron pipe/ PVC drain pipes/PVC (SWR) pipe etc, 75mm jointed in cement mortar and taking out of trenches and wall, if required complete all as specified and directed.

Dismantling wall and ceiling boards (fibre,pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets complete, all as specified and as directed by Engr-in-charge.

Taking up or down steel tubing and connections of 15mm bore in pipe, including cleaning for re-fixing or removal from site to store complete all as specified and directed by Engineer-in-Charge.

Taking up or down steel tubing and connections of 20mm bore in pipe, including cleaning for re-fixing or removal from site to store complete all as specified and directed by Engineer-in-Charge.

Hacking out old broken glass (any thickness, size, quality or description) from metal frame including punching or drilling out old glazing pins/spring clips and providing and fixing new ones (up to 4th storey of building) complete all as specified and directed by Engr-In-Charge.

Cutting grooves in brick wall,75mm wide and 65mm deep and shaping horizontal face of groove with cement mortar 1:3 all as specified and directed.

Disconnecting/dismantling existing tanks of capacity exc. 500 ltr & n. exc. 1000 ltr, setting aside and removing from site complete all as specified and directed by Engineer-in-Charge.

Disconnecting/dismantling existing tanks of capacity exc. 250 ltr & n. exc. 500 ltr, setting aside and removing from site complete all as specified and directed by Engineer-in-Charge.

Disconnecting existing tanks of capacity exc 250 ltr but not exc 500 ltr , setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position. (Cleaning repairing, etc. measured separately) complete all as specified and directed by Engineer-in-Charge.

All as per item No 18 but exc 500 ltr and n exc 1000 ltr.

Cleaning and removing all scale and dirt, etc, from tanks and from mouths of circulating pipes, etc of capacity exc 500 ltr but not exc 1000 ltr complete all as specified and directed by Engineer-in-Charge.

All as per item No.20 here-in-before but capacity exc 500 litres and n.exc 1000 litres.

Demolition of brick work or stone/boulder masonary built in cement mortar incl all quions arches, pillar or any other descrption etc complete all as specified and directed by Engineer-in-Charge.

M&L providing cement concrete type C1 1:3:6 (20cm graded aggregate) in coping,hold fast, bed blocks including form work all as specified and directed.

Reinforced Cement Concrete nominal mix 1:1.5:3 type A-1 using 20mm graded mechanically crushed stone aggregate as in slabs supported on walls, beams and columns in floors,chajjas,drilling ,welding in old steel, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed by Engineer-in-Charge.

TMT steel bars 10mm dia and over, of grade Fe-500D cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed by Engineer-in-Charge.

All as per item no. 27 above but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders complete all as specified and directed by Engineer-in-Charge.

Use & waste Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete rail ings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide (Rough finished surfaces of concrete) complete all as specified and directed by Engineer-in-Charge.

Use & waste Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) (Rough finished surfaces of concrete ) complete all as specified and directed by Engineer-in-Charge.

M&L for Glazed ceramic coloured /printed tiles of size 300mmx 450mmx7mm thick as in skirting/dado setting & jointed with 4 mm spacer and grouting the joint with epoxy grout mix of organic coated filler of desired shade , hardener,resin in the ratio of 8:1:2 over & including 10mm thick rendering of cement sand mortar (1:4) and pointed with appoxy coloured cement to match with surface of tiles complete all as specified and as directed.

Vitrified ceramic tiles double charged dark shade 10 mm thick (Square/rectangular) polished, area of each tiles not exceeding 0.36 Sqm, laid as in floors, set and jointed setting & jointed with 4 mm spacer and grouting the joint with epoxy grout mix of organic coated filler of desired shade , hardener,resin in the ratio of 8:1:2 over & including 15mm thick bedding of cement sand mortar (1:6) and pointed with appoxy coloured cement to match with surface of tiles complete all as specified and as directed.

M&L for coloured ceramic tiles 7 mm to 8 mm thick (square ,rectangular) area of each tile exceeding 0.11sqm but not exc 0.18 Sqm laid as in floors, set and jointed setting & jointed with 4 mm spacer and grouting the joint with epoxy grout mix of organic coated filler of desired shade , hardener,resin in the ratio of 8:1:2 over & including 15mm thick bedding of cement sand mortar (1:6) and pointed with appoxy coloured cement to match with surface of tiles complete all as specified and as directed.

M&L for coloured ceramic tiles 8 mm to 9 mm thick (square ,rectangular) area of each tile exceeding 0.18sqm but not exc 0.38 Sqm laid as in floors, set and jointed setting & jointed with 4 mm spacer and grouting the joint with epoxy grout mix of organic coated filler of desired shade , hardener,resin in the ratio of 8:1:2 over & including 10mm thick bedding of cement sand mortar (1:6) and pointed with appoxy coloured cement to match with surface of tiles complete all as specified and as directed.

All as per item No 34 but a in skirting over and including rendering 10 mm thick on brickwork or concrete surfaces finished even and fair in CM 1:4 complete all as specified and as directed.

Granite 18-20 mm thick, (table rubbed and polished) in single piece (in one direction) machine cut, machine polished, bedded and jointed with adhesive suitable for granite/stone & pointed with grout of matching shade including necessary cutting over & including 15 mm thick (average thickness) cement mortar (1:4) screed, as in cooking platform, shelves, RCC counters, window cills & similar situations rounded and chamfered edges of stone slab, complete all as specified and directed by Engineer-in-Charge.

Brick work with sub class 'B' bricks, class designation 100, old size bricks, straight or curved on plan exceeding 6.00 metre mean radius built in cement mortar 1:6 complete all as specified and directed by Engineer-in-Charge.

Material & labour for brick work with sub class 'B' bricks, old size, straight or curved on plan exceeding 6 mtr mean radius and built in cement mortar (1:6) complete all as specified and directed.

Rendering 15 mm thick in cement mortar 1:6, on other than fair faces of brick or concrete surfaces , trowelled to even and smooth surface without using extra cement, complete all as specified and directed by Engineer-in-Charge.

Rendering 15 mm thick in cement mortar 1:4, on brick or concrete surfaces in two layers mixed with water proofing compound on top layer, trowelled to even and smooth without using extra cement, (up to 4th storey of building) complete all as specified and directed by Engineer-in-Charge. NOTE: Water proofing compound shall be measured and paid separately.

Supply only liquid water proofing comound ISI Marked complete all as specified and directed.

Rendering 5 mm thick in cement mortar 1:3 as in ceiling/soffits of slabs/Chajja/ Sunshade finishing the plastered surface even & smooth without using extra cement etc complete all as specified and directed by Engineer-in-Charge.

Preparation of new plastered surfaces of wall and applying two coats of oil bound distemper on walls over and including 1 mm wall care puty including a coat of alkali resitant priming paint complete all as specified and directed.

Preparation of new plastered surfaces of ceilings and applying two coats of oil bound distemper on ceilings over and including a coat of primer including preparation of surface complete all as specified and directed.

Preparation of new plastered surfaces of wall and finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) complete all as specified and directed.

M&L for complete removal of existing surface and applying two coats of oil bound distemper over and including a coat of primer and 1 mm wall care puty on wall/ceiling surfaces (upto 4th story of bldg), complete all as specified and as directed.

Preparation of old Plastered of walls etc by brooming down or steel wire brushing, scrapping down smoke soot moulds, moss, efflorescence salts treating oil and greasy spots etc and applying two coats of oil bound distemper on walls (upto 4th story of bldg), complete all as specified and directed by Engineer-in-Charge.

M&L for applying 1 mm thick wall care putty to achieve smooth surfaces on old or new surface complete all as specified and as directed by Engr-in-Charge.

M&L for one coat of synthetic enamel paint over old painted wooden or wood based surfaces of any description, not otherwise described over 10 cm width or girth, including preparation of surfaces complete all as specified.

M&L for one coat of synthetic enamel paint over old painted steel surfaces of any description, not otherwise described over 10 cm width or girth, including preparation of surfaces complete all as specified.

Preparation of new or previously untreated wooden surface of any description not otherwise described over 10cm width or girth and applying two coat of synthetic enamel paint over one coat of pink primer complete all as specified and directed by Engineer-in-Charge.

Preparation of new or previously untreated steel and iron surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed by Engineer-in-Charge.

M&L for complete removal of existing surface and preparation of surfaces of ceiling, brooming down and applying two coats of white wash on walls complete all as specified and directed by Engineer-in-Charge.

All as per item No 53 above but one coat of white wash on ceiling ,complete all as specified.

Complete removal of existing treatment,preparation of surfaces and applying two coats of weather proof exterior emulsion paint(Ist quality) Apex over two coats of primer on damp surface as per manufacturers instructions etc including properly filling the cracks with putty,applied by approved applicator (upto 4th story of bldg), complete all as specified and directed by Engineer-in-Charge.

Factory made Pressed steel frames, confirming to IS, having profile 125 x 60 mm , 1.25 mm thick MS sheet for doors with one or more rebates including necessary fixing lugs, and 100 mm size hinges, lock strike plate, etc., with one shop coat of zinc chromate primer and fixing complete all as specified and directed by Engineer-in-Charge.

Factory made Pressed steel frames, confirming to IS, having profile 105 x 60 mm , 1.25 mm thick MS sheet for doors with one or more rebates including necessary fixing lugs, and 100 mm size hinges, lock strike plate, etc., with one shop coat of zinc chromate primer and fixing complete all as specified and directed by Engineer-in-Charge.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed Stainless steel screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/Stainless steel dash 100mm/125mm long fasteners of required dia complete as per direction of Engineer-in-Charge.

18 mm thick Factory made single extruded WPC (Wood Polymer Composite) solid plain board comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws including PVC beading on exposed surfaces, all as per direction of Engineer-In-Charge. NOTE :- Material test certificate and authentication shall be provided by the manufacturing company

Factory made single extruded WPC (Wood Polymer Composite) solid plain board of size 25 mm thick comprising of virgin polymer of K value 58-60 Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter including PVC beading on exposed surface complete all as specified and directed by Engineer-in-Charge.

Supply and fixing of factory made 25 mm thick single extruded WPC (Wood Polymer Composite) solid single side PVC Laminate with PVC foil of minimum 14 Microns thick of approved colour shade Board comprising of virgin polymer of K value 58-60 (suspension grade) calcium carbonate & Natural Fibers (wood power / rice husk /wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant , including PVC Beading on exposed surface all as per the direction of Engineer-In- Charge. Note : Material test certificate& authentication should be provided by the manufacturing company.

18 mm thick Factory made single extruded WPC (Wood Polymer Composite) solid plain board comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws including PVC beading on exposed surfaces, all as per direction of Engineer-In-Charge . NOTE :- Material test certificate and authentication shall be provided by the manufacturing company

18 mm thick Factory made single extruded WPC (Wood Polymer Composite) solid single side PVC laminate with PVC foil of minimum 14 microns thick of approved colour shade board comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws including PVC beading on exposed surfaces, all as per direction of Engineer-In-Charge . NOTE :- Material test certificate and authentication shall be provided by the manufacturing company

S&F for factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing complete all as specified and as directed.

M&L for 35 mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercialm type with 0.80 mm mica on both sides complet all as specified and directed.

35 mm thick factory made glazed & Skeleton shutters of 2nd class Hardwood open rebated & prepared to receive glass or gauze etc without sash bar open rebated with edges of framing plain, chamfered or rounded, fitted with cut & mitred beads for securing glass or guage etc size ofstiles rails etc as specified in sec 8 clause 8.24 (a) of SSR Part-I (2009) complete all as specified and directed by Engineer-in-Charge.

Solid PVC door frames of size 50mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube, and edges will be painted to match with printed sheet, supply & fixing in opening as per specification & drawing complete all as specified and directed by Engineer-in-Charge.

S&F aluminium powder coated (min thickness of powder coating 50 micron) frame for door , windows, ventilators and weight of aluminium section not les than 0.55 kg/Rm with one or more rebates including joining cleat/aluminium beading for fixing etc complete all as specified.

S&F aluminium powder coated (min thickness of powder coating 50 micron) anodised aluminium window and ventilator shutters, side hung type without sash bars,including (double shutter) glazing bars and without glazing bars weight of aluminium section not les than 0.55 kg/Rm including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). suitable handle D type (1 no.), tower bolt 2 Nos complete all as specified.

Aluminium anodised,barrel tower bolts of extruded section with length of bolt 150 mm and dia of bolt not less than 10 mm,ISI marked complete all as specified and directed by Engineer-in-Charge.

S&F stainless steel butt hinges 100mm size medium weight cold rolled mild steel of any frame as wooden/metal through nut&bolt/welding complete all as specified and directed.

300 mm long,Aluminium alloy, anodised,sliding door bolt with hasp,staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified & directed by Engineer in Charge.

S&F 144 mm long Stainless steel finish zinc chrome handles, curve design,fixed with stainless steel screws complete all as specified and directed by Engineer-in-Charge. Make: Godrej, Hettich, Hafale and equivalent.

150 mm long extruded aluminium alloy handles, fabricated type,anodised complete all as specified and directed by Engineer-in-Charge.

Floor door stopper of aluminium alloy body and tongue, anodised,with hard drawn steel spring,fixed in floor with overall length of cover plate 140 mm complete all as specified and directed by Engineer-in-Charge.

S&F mild steel helical door spring MS 300mm long ordinary rat tail pattern spring including roller & roller plate complete fixed to wooden/steel chowkats complete all as specified and directed by Engineer-in-Charge.

S&F in repair Continuous (piano hinges) 30mm width of flap in repairs Paino hinges, mild steel bright finish (width of flap 30mm) complete all as specified and directed by Engineer-in-Charge.

S&F in repair door closer (Aluminium die cast body) hydraulically regulated,designation No. 2,universal type, suitable for door shutters upto 1200mm in width and of weight between 36 to 60 kg and fixed complete all as specified and directed by Engineer-in-Charge.

Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm fixed with stainless steel wire staples complete all as specified and directed by Engineer-in-Charge.

Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm fixed with stainless steel wire staples complete fixed in reapir all as specified and directed by Engineer-in-Charge.

S&F Toughened glass 12 mm thick including fixing with cleat in floor,ceiling and lining alongwith hinges to hold door arrangements including hacking out old glass complete all as specified and directed by Engineer-in-Charge.

Sheet glass 4.8mm thick, ordinary quality and glazing with silicon sealant & spring glazing clips using Silicon for fixing of glass in addition to glazing putty, in squares not exceeding 0.5 Sq. mtr in each pane (up to 4th storey of building) complete all as specified and directed by Engineer-in-Charge.

Sheet glass 4.8mm thick tinted/plain/Figured glass type, ordinary quality and glazing with silicon sealant & spring glazing clips using Silicon for fixing of glass in addition to glazing putty, in squares not exceeding 0.5 Sq. mtr in each pane (up to 4th storey of building) complete all as specified and directed by Engineer-in-Charge.

Sheet glass 4mm thick, ordinary quality and glazing with silicon sealant & spring glazing clips using Silicon for fixing of glass in addition to glazing putty, in squares not exceeding 0.5 Sq. mtr in each pane (up to 4th storey of building) complete all as specified and directed by Engineer-in-Charge.

Sheet glass 4mm thick, ordinary quality and glazing with silicon sealant & spring glazing clips using Silicon for fixing of glass in addition to glazing putty, in squares exceeding 0.5 Sq. mtr in each pane (up to 4th storey of building) complete all as specified and directed by Engineer-in-Charge.

Material & labour for 25mm dia stainless steel pipe curtain rod, powder coated fixed with & including stainless steel hooks/ brackets and decorative finials (at both side), curtain rings (minimum 5 Nos rings per running mtr of curtain rod) shade as approved by GE complete all as specified includng fixing of long size rawl plugs in wall for MS hook including taking out the existing old pelmet box along with old curtain rods complete all as specified and directed.

M&L for providing and fixing stainless steel (Grade 304) railing made of hollow tubes, window grills, channels, plates, cap etc, including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including all asseary complete all as specified including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement complete all as specified.

Supply and fixing for chrome plated food grade stainless steel wire in any baskets of a moduler kitchen (storage basket, cup and saucer basket, jas basket, thali basket, cutlery basket, grain trolley, plain basket, bottle pull out etc), min loading capacity 65 KG, made by min 6 mm dia stainless steel round bars, proper welded and joints finish by grinding, chromium plated finish, fixed properly with WPC board of any thickness as per design approved, including fixing of auto closing hinges, ball bearing runners of any description, stainless steel handles fixing clips, sliding frame structure, Stainless steel screw etc complete ,all as specified and directed by Engineer-in-charge. Note : 1. Weight of fitting/fixtures like handles, hinges, ball bearing runners, telescopic channels etc will not be measured. 2. Only weight of Stainless steel wire basket will be measured before fixing. 3. Only Fixing of all Fitting/fixtures like handles, hinges, ball bearing runners, telescopic channels etc are included in this item supply of the same will be paid in saperate items as supply only.

Supply only Stainless steel soft auto closing hinges openable at 0 degree fixed with stainless steel screws to PVC/Wooden moulded shutters frame work in kitchen cabinets,cupboards etc complete all as specified and directed by Engineer-in-Charge. Make Godrej, Hettich, Hafale or equivalent as approved by GE.

Supply and fixing magnetic catcher cum silencer CP and fixed with standard steel screws, complete all as specified and directed.

Supply only of Ball bearing runners 45 mm Telescopic Channel ( 20 Inch ) full extension load capacity 50 kgs, Black powder coated, Make; ( Hettich, Ebco, Prime )

S&F Stainless steel cupboard locks, 2 levers with 2 no of keys complete all as specified and directed by Engineer-in-Charge.

Supply and fix in repair Floor machine heavy duty ISI marked for aluminium door with all accessories etc complete all as specified and directed by Engineer-in-Charge.

M&L for PVC prelaminated Gypsum Ceiling board 9mm thick with and including anodised aluminium snap grid framework for ceiling having grid size 605 x 605 mm comprising of wall angle of size 25 mm x 25 mm x1.3 mm,main runner of size 38 mm x 25 mm x1.3 mm. The grid system shall be suspended at every 1200 mm c/c in both directions by using 3.5 mm dia aqualine wire fixed to purlin or RCC roof with suitable fasteners to withstand the load of grid system with ceiling board complete all as specified and as directed by Engr-in-charge. Note :Colour to be decided by GE

S&F in repair 5mm thick coloured wood grain printed PVC sheet strips in wall panelling over and including PVC frame and overlap strips and corner angles complete inclusive of Solvent Cement and fixing at site as per manufacturer's instructions complete all as specified and directed.

S&F in repair for Vitreous China wash down water closet pan ( pedestal pattern) white ( excluding flushing cistern and flush pipe) including plastic water closet seat cover white with stainless steel L-type jet spray with 1 m hose pipe, closed pattern with flat botton and cover and mild steel chromium plated or aluminized hinging device incl P or S trap with connection complete all as specified and directed.

S&F for vitreous china white wash basin (flat back or angle back type) of size 550mmx400mm coloured including MS brackets, cutting for and pinning in ends of brackets, including bottle trap/ PVC waste pipe as in repairs complete all as specified and as directed.

S&F single piece WC of size 365x655x765 with flushing cistern and connection pipe, P or S trap (closed pattern incl all necessary accessories like rag bolts, kitt /gel gasket etc, (including flushing cistern, pvc seat cover , jet and flush pipe complete all as specifed and directed.

Supply and fixed in repair flushing kit internal for single piece EWC complete all as specified and directed by Engineer-in-Charge.

S&F in repair 10 ltr capacity PVC valveless, syphonic action dual flush type flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets, 32 mm dia flush pipe complete all as specified and directed by Engineer-in-Charge.

S&F for one pice PVC hydrolica plastic water closet seat cover (white coloured) closed pattern with flat bottom, cover and mild steel chromium plated or aluminium hinges device for pedestal pan fixed as in repair complete all as specified and as directed.

Supplying and fixing in repairs table top vitreous china wash hand basin of size 600 mm x 450 mm x150 mm including CI brackets , chromium plated waste coupling, waste pipe etc., (incl all waste fittings) complete all as specified and directed by Engineer-in-Charge.

Supply and fixed in repair Brass chromum plated 3‐In‐1 System wall mixer with Provision telephonic shower and overhead Shower for mixing hot and cold water fancy type with screwed down for 15mm dia iron pipe With 115mm Long Bend Pipe, Connecting Legs & Wall Flange (Without Hand Shower & Overhead Shower) complete all as specified and directed by Engineer-in-Charge.

S&F for wall mixer 15mm dia with spout, fancy type, chromium plated Brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixedas in repair complete all as specified and as directed.

S&F for Sink mixer 15mm dia with spout, fancy type, chromium plated Brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixedas in repair complete all as specified and as directed.

S&F 15 mm bore fancy type Pillar taps, cast copper alloy, with capstan heads,chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed to 15 mm bore iron pipe as in repair complete all as specified and as directed.

S&F in repairs 2 way Pillar cock single lever of 450mm long fancy type , cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with ‘Hot' or ‘Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and as directed.

Supplying and fixing in repairs 15 mm fancy type chromium plated fancy type bib tap brass long body with flange screwed down high pressure CP cast copper alloy with crutch or butterfly handles screwed down suitable for 15mm bore pipe or union complete all as specified and directed by Engineer-in-Charge.

Supplying and fixing in repairs 15 mm fancy type chromium plated bib tap brass long body with flange screwed down high pressure CP cast copper alloy with crutch or butterfly handles screwed down suitable for 15mm bore pipe or union complete all as specified and directed by Engineer-in-Charge.

S&F in repair 15 mm bore 2 way Bib tap, brass chromium plated, fancy type, with crutch or butter-fly handle, screwed down, screwed for iron pipe or for brass ferrule etc all as specified and directed.

Supplying and fixing in repairs stop/angle valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions, all as specified, of 15mm bore, fancy type, chromium plated complete all as specified and directed by Engineer-in-Charge.

Supplying and fixing in repairs stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions, all as specified, of 15mm bore, fancy type, chromium plated with long shank and cup (Concealed type) complete all as specified and directed by Engineer-in-Charge.

Supplying and fixing in repairs stop/angle valves, chromium plated cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions, all as specified, of 15mm bore, fancy type, chromium plated complete all as specified and directed by Engineer-in-Charge.

Supply & fix in repairs chromium plated, Brass, Jet spray including flexible pipe 15mm bore, screwed down, high-pressure pipe of 15 mm bore with wall flange fixed to wash down water closet (pedestal pattern) complete all as specified and directed.

S&F in repair Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified as directed

Supply and fixed in repair Brass chromum plated overhead shower rose of size 150 x 150 mm (square ) with Brass chromum plated shower arm 450 mm long with flange with swivel joints, fancy type screwed down for 15mm dia iron pipe complete all as specified and directed by Engineer-in-Charge.

S&F Soap Dish Holder chromium plated complete all as specified and directed. Make: Cat part No ACN - 1131N of Jaquar or equivlaent of Cera, Somany

S&F Liquid soap container of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 105gms) complete all as specified and as directed.

S&F in repairs toilet paper holder chromium plated with fixing to wall complete all as specified and directed. Make : Jaquar (Cat part No 1151N) or equivlaent of Cera, Somany

S&F in repair brass chromium plated Tubler towel rail, 20mm dia, D type, 60cm long between flange, Complete all as specified and as directed

S&F glass shelf assembly 5.5mm thick, 12 cm wide and 600 mm long fixed with & including chromium plated brass screws and stainless steel cleats and frame (Minimum weight 300gms) fixed in repair complete all as specified and as directed.

S&F kitchen sinks of stainless steel 1mm thick with drainage board with plugs,washers and wastes couplig ;including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 495mm X 420mm and bowl size 410mm X 330mm X 160mm complete all as specified.

S&F kitchen sinks of stainless steel 1mm thick with drainage board with plugs,washers and wastes couplig ;including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm X 460mm and bowl size 410mm X 330mm X 160mm complete all as specified.

S&F in repair kitchen Plate Rack stainless steel having size 750mm x600mm x250mm (approx) made of stainless steel of wall thickness 1mm thick incl fixing to walls with fasteing screws, rubber/PVC beading /capping complete to sustain utensils weight upto 8-10 Kg, complete all as specified and directed.

S&F in repair kitchen Plate Rack stainless steel having size 900mm x750mm x300mm (approx) made of stainless steel of wall thickness 1mm thick incl fixing to walls with fasteing screws, rubber/PVC beading /capping complete to sustain utensils weight upto 8-10 Kg, complete all as specified and directed.

S&F Swivel shower of CP with shower arm 15mm size,125 mm long with bend of 45 degree with flange of PTMT any colour for fixing with 15mm pipe (Minimum weight 40 gm) IN REPAIR, complete all as specified.

S&F in repair waste pipe 32mm dia, 800mm long with cup and nuts complete all as specified & directed

Stainless steel grating 127 mm dia with locking system complete all as specified and directed by Engineer-in-Charge.

S&F for PVC connections with PTMT nuts of length 600 mm long fixed to 15 mm bore iron pipe or union as in repair complete all as specified and as directed.

Supplying and fixing in repairs waste coupling of Chromium Plated bore dia of discharge pipe 32mm (half or full threaded) (Minimum weight 45gms) for Sink and WHB complete all as specified and directed by Engineer-in-Charge.

S&F for 110mm dia PVC (SWR) pipes single socketed pressure rating not less than 4 Kg/SQ Cm, ISI Marked with rubber ring joints, laid in trenches /fixed to wall/floor complete all as specified and directed.

S&F 75 mm PVC (SWR) pipes single socketed,pressure rating not less than 4 Kg/SQ Cm, ISI Marked in any length with rubber ring joints, laid in trenches /fixed to wall/floor complete all as specified and directed.

PVC (SWR) floor trap, plain with grating including jointing with solvent cement 75 mm bore fixed in repair including jointing to waste pipe in cement concrete type B-1 (1:2:4) complete all as specified and directed by Engineer in Charge.

PVC(SWR) bends (any radius), for 110mm bore pipes, with access doors, complete all as specified and directed by Engineer-in-Charge.

PVC(SWR) bends (any radius), for 75 mm bore pipes, with access doors, complete all as specified and directed by Engineer-in-Charge.

S&F in reapir Cast iron 'P' or 'S' trap, ISI marked, suitable for 100 mm bore CI spun pipes complete all as specified.

CPVC(SDR-11) of outer dia 20 mm with and including CPVC SDR-11 brass and plain fittings on walls and ceilings or laying in floors complete all as specified and directed by Engineer-in-Charge.

CPVC(SDR-11) of outer dia 25 mm with and including CPVC SDR-11 brass and plain fittings on walls and ceilings or laying in floors complete all as specified and directed by Engineer-in-Charge.

CPVC SDR- 11 Tank Adaptor nipple fittings, ISI marked for CPVC pipe outer diameter 20 mm bore complete all as specified and directed by Engineer-in-Charge.

CPVC SDR- 11 brass UNION fittings, ISI marked for CPVC pipe outer diameter 20 mm bore complete all as specified and directed by Engineer-in-Charge.

CPVC SDR- 11 Ball valve fittings, ISI marked for CPVC pipe outer diameter 20 mm bore complete all as specified and directed by Engineer-in-Charge.

CPVC SDR- 11 Ball valve fittings ISI marked for CPVC pipe outer diameter 25 mm bore complete all as specified and directed by Engineer-in-Charge.B156:B157

Note: For the purpose of arriving at lumpsum amount, the amount of credit schedule i.e Sch 'A' section II (i.e Rs 50,528.00 shall be deducted from the total amount arrived.

Total of Schedule 'A' Rs.

Please Enable Macros to View BoQ information