Construction of Sports Stadium at village Silana in Distt. Jhajjar (CM Announcement Code No. 11085 Dated 08.04.2016) (Providing 500 KVA Sub Station and 200 KVA DG Set only). Recall

Amount

HSR Items

[20.89.9]`Designing, Supply and erection of DG set of capacity given below with noise controlled devices acoustic of suitable rating, testing and commissioning of diesel generating set, radiator cooled, 3 phase, 4 wire, 50 cycles 415 plus (-)1% volts AC alternator coupled directly through a set of flexible coupling on a common MS fabricated base frame with diesel engine complete with suitable size incoming cable from generator to change over/AMF panel, making 2nd incoming cable connection from transformer, outgoing cable connection from changeover/ standard panel, making second incoming cable connection from transformer, outgoing cable connection from changeover / STD panel to incomer of motor starter panel, fenced enclosure with platform for DG sets complete as per following detailed scope and specifications and directions of Engineer-in-charge. The rating should be at 1500 RPM. a) Diesel Engine b) Alternator c) Battery 24 V. d) Base Plate. e) suitable sq mm suitable core copper cable upto 40 metres. f) Tools, standard panel g) Metering set 415 VAC-1 set (Amp. meter, Volt Meter, ASS, VSS, Phase Indicator, control fuse, frequency meter, CT`s) h) Metering set 60/5A/110V (Amp. Meter, Volt Meter) i) Overload protection for DC-1 No. j) Battery Charger 24V DC k)Copper bus bar of suitable size l) KWH meter 96 sqmm size m) Starting fuse button and key switch9on/off) n) Indicating lamps for low lubricated oil pressure, high coolant temperature, set running, load on, Dc control and other required accessories complete in all respects to the satisfaction of Engineer-in-charge` 9. 200 KVA

[23.22.1.6]MCCB ,DISTRIBUTION BOARDS, MCB`s, RCCB`s, CHANGE OVER etc. 1.6. Supply and erection of Modular case circuit breaker single pole/4 pole on existing wall/pedestal/Panel including bounding to earth and making necessary connections required to complete the job in all respect up to the entire satisfaction of the Engineer-in-charge of the work. TRIPLE POLE MCCB 300 Amp, 25 KA

[24.1.1]EARTHING AND LIGHTENING ARRESTOR 1. Earthing with GL earth pipe 4.5 m long and 40 mm dia with masonry enclosures on the top etc. (but without charcoal or coke and salt) as required.

[24.1.10]EARTHING AND LIGHTENING ARRESTOR 10. Providing and fixing 25 mm x 5mm copper strip on surface or in recess for connections etc. as required with all labour and material.

[24.1.2]EARTHING AND LIGHTENING ARRESTOR 2. Extra for using salt and char coal/coke for pipe earth electrode as required.

[24.1.4]EARTHING AND LIGHTENING ARRESTOR 4. Earthing with tinned copper earth plate 600mmx600mmx3mm thick including accessories and providing masonry enclosures with cover plate having locking arrangement and watering pipe etc. (but without charcoal or coke and salt) etc. complete as required.

[24.1.5]EARTHING AND LIGHTENING ARRESTOR 5. Extra for charcoal or coke and salt for G.I. plate or copper plate earth electrode.

[24.1.9]EARTHING AND LIGHTENING ARRESTOR 9. Providing and fixing 25 mm x5 mm copper strip in 40 mm dia G.I. pipe from earth electrode as required.

[24.2.7.3]LT CABLE 7.3. Supply and erection of suitable compression type brass cable glands for underground Cable :- 25 sqmm to 50 sqmm Cable 2 to 4 Core

[24.2.7.5]LT CABLE 7.5. Supply and erection of suitable compression type brass cable glands for underground Cable :- 120 sqmm to 185 sqmm Cable 3 to 32 Core

[24.2.7.6]LT CABLE 7.6. Supply and erection of suitable compression type brass cable glands for underground Cable :- 240 sqmm to Cable 3 to 32 Core

[24.3.3.1]HT CABLE 3.1. Supplying and making indoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required :70 to 120 sqmm

[24.3.4.1]HT CABLE 4.1. Supplying and making outdoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required :70 to 120 sqmm

[24.5.2.3]MISCELLANEOUS ITEMS 2.3. S/E mark double walled corrugated (DWC) HDPE, pipe 10 Kg/Cm2 ,laid 0.75 Metre below ground level including digging and refilling of earth including cost of suitable size socket/coupler for HDPE pipe including the cost of labour and material required to complete the job in all respect up to the entire satisfaction of Engineer in charge of the work. DWC/HDPE pipe 63/50 mm outer dia/inner dia

[24.5.2.4]MISCELLANEOUS ITEMS 2.4. S/E mark double walled corrugated (DWC) HDPE, pipe 10 Kg/Cm2 ,laid 0.75 Metre below ground level including digging and refilling of earth including cost of suitable size socket/coupler for HDPE pipe including the cost of labour and material required to complete the job in all respect up to the entire satisfaction of Engineer in charge of the work. DWC/HDPE pipe 90/75 mm outer dia/inner dia

[24.5.2.5]MISCELLANEOUS ITEMS 2.5. S/E mark double walled corrugated (DWC) HDPE, pipe 10 Kg/Cm2 ,laid 0.75 Metre below ground level including digging and refilling of earth including cost of suitable size socket/coupler for HDPE pipe including the cost of labour and material required to complete the job in all respect up to the entire satisfaction of Engineer in charge of the work. DWC/HDPE pipe 120/105 mm outer dia/ inner dia

[24.7.5]RCC FOUNDATIONS FOR DG SET 5. 250 KVA DG Set

NS Items

Providing and fixing of stay set complete with stay wire with dis insulator as per specification upto the entire satisfaction of Engineer-in-charge of work..

S/E of 11 KV gang operated switch `Jayshree make` conforming to IS with latest amendment including suitable size of copper blade erection of same on the existing `H` pole fixed with angle of size 50x50x6mm, suitable size of MS clamp, nuts and bolts including cost of 6 Nos. 11 KV insulator with GI Pin, RD fuses and painting with 2 coats of approved paint and one coat of red oxide material required to complete the job in all respect utpo the entire satisfaction of Engineer-in-charge of work.

Supply and erection of Fire extinguisher ISI mark Co2 type of 4.5 Kg. capacity as per IS 7285 duly erected / hung on wall with hooks with all labour and petty material required to complete the job in all respect upto the entire satisfaction of Engineer-in-Charge of the work.

Supply and Erection of MS Bucket Stand made of 32 x 5 mm angle iron / channel iron suitable for 6 Nos. fire bucket including cost of 6 Nos. bucket, welding and painting of complete stand with one coat of red oxide and two coats of approved paint of red color with all labour and material required to complete the job in all respect upto the entire satisfaction of the Engineer-in-Charge of the work.

Supply and erection of prestressed cement concrete pole as per IS : 1678-1960 (i) 9 Metres long 105 mm x 115 mm at Top and 105 mm x 315 mm at bottom with working load of 200 Kg. burried 1.80 m in ground

Supply and erection of Rubber Mat of size 2m x 1 m x 12 mm thick suitable for 11 KV complete in all respect make and model approved by Chief Electrical Inspector.

Supply, erection, testing and commissioning of 11 KV indoor H.T. Metering panel complete with CTs, PTs cubical and electronics meter with accuracy class 0.5 as per requirement / approved by HVPN Consisting of the following : (i) Cubical panel free standing floor mounting type made of sheet steel 14-G SWG CRCA sheet with channel iron base frame spray paintd with strong Synthetic grey channel paint as per size and design approved by HVPN . (ii) 3 Nos. 11 KV CTs of rating as approved by HVPN for indoor installation of approved make of HVPN. (iii) One No. 11 KV PT 11000/110 Volts 10 KA burden 0.5 accuracy oil filled suitable for indoor installation of approved make of HVPN. (iv) Digital electronic meter 3 Phase 4 wires 0.5 accuracy for recording reading operating system for difference kind of readings. The cubical panel will be complete in all respect including interconnection, internal wiring with PVC copper cable its testing and approved of all items by HVPN including cost of all testing/approved charges of all items of HVPN including cost of all labour and material required to complete the job in all respect upto the entire satisfaction of the Engineer-in-Charge ofthe work.

Supply, erection, testing and commissioning of 11 KV VCB Panel having air insulated bus bar extensible type chamber complete with a set ( one No. incoming and 1 No. outgoing ) of 3 wires 800 Amp. copper bus bar as per specifications given below up to the entire satisfaction of Engineer-in-Charge of the work. A. Vacuum Circuit Breaker (Incommer) Make –Crompton Greaves Ltd. 1 No. 11KV, 800Amp., 25 KA/Sec Horizontal Drawout Horizontal isolation panel 1 No. 230V AC Motorised Mechanism 1 No. 3-Ph,PVC Sleeved Alu Bus Bar, 800Amp 1 No. Colour Coded Wiring with 2.55q,mm for CT and PT circuit and 2.5Sq.mm for other circuit 1 No. Degree of Protection - IP4X Paint Shade RAL 7035 1 No. Power pack-220/110VAC/24V DC 1 No. Shunt Trip/closing Coil Voltage-24V DC 1 No. Warning plates B. EPOXY RESIN CAST V.T.: Make-CGPISL 1 No. 3 Phase, Cast resin Drawout type PT`s of ratio 11KV/V3/110V/V3, Acc.cl -0.5 Burden: 100VA C. EPOXY RESIN CAST,1-Ph CT (25KA/1sec) Make-CGPISL 3 Nos. Ratio 50/25/5-5 A, 5 VA burden, cl-0.5 and SP10,5VA, ON PI SIDE Ratio 50/25-5-5 A, 15 VA burden, cl-0.5 and 5P10,15VA,ON P2 SIDE D. Power Pack 24 VDC E. Meters Make-SECURE/AE/ Equivalent 1 No. Voltmeter with S/S. 1 No. Ammeter with S/S.

B. Capacitor Bank 10 KVAR = 1 No. 1 No. MCB 32 Amp. TP 10 KA of LandT Make 1 No. Contactor MOC 10 of LandT Make 1 No. Capacitor 10 KVAR of Epcos Make 1 No. A/M Switch of LandT Make 1 No. Indication Red of Essen Make C. Capacitor Bank 15 KVAR = 1 No. 2 Nos. MCB 63 Amp. TP 10 KA of LandT Make 2 Nos. Contactor MOC 15 of LandT Make 2 Nos. Capacitor 15 KVAR of Epcos Make 2 Nos. A/M Switch of LandT Make 2 Nos. Indication Red of Essen Make D. Capacitor Bank 20 KVAR = 1 No. 1 No. MCB 63 amp. TP 10 KA of LandT Make 1 No. Contactor MOC 20 of LandT Make 1 No. Capacitor 20 KVAR of Epcos Make 1 No. A/M Switch of LandT Make 1 No. Indication Red of Essen Make E. Capacitor Bank 25 KVAR = 8 Nos. 8 Nos. MCB 63 Amp. TP 10 KA of LandT Make 8 Nos. Contactor MOC 25 of LandT Make 8 Nos. Capacitor 25 KVAR of Epcos Make 8 Nos. A/M Switch of LandT Make 8 Nos. Indication Red of Essen Make Fabrication with Copper Bus Bar, Power and control wiring, labour and margin

Supply, erection, testing and commissioning of outdoor type copper wound, transformer of 500 KVA 11 / 433 KV, 3 Phase, 50 Hz complete in all respect upto the entire satisfaction of Engineer-in-charge of work ( on existing pole / plateform including first filling of oil conforming to IS 1180 level -2- Make : Alstom, Kirloskar, Crompton, NGEF, Voltamp., ABB, Siemens, Schneider KVA 500 No. load voltage ratio 11/ 433 KV No. of Phase 3 Frequency cycles 50 Hz Types Double wound core type Copper wound. Cooling ONAN Duty outdoor Vector Group ISS-DYN 11 / IS 2026 /77 Tapping on HV compensation plus 5% to - 5% Insteps of 2.5% Temperature rise (Oil / res.00) 500 / 550 C Attitude upto 1000 m above MSL Off circuit tape changer Externally hand operated Oil conservator with filling hole and cap Plain oil level gauge with minimum level marking Thermometer pocket

4 Nos. Plain roller undirectional. 1 No. 4` dial type thermometer Silica Gel breather Ist filling of oil. Drain cum filter valve with plug. Rating and diagram plate. Two earthing terminals Lifting arrangement Explosion vent Air release plug. Oil conservator tank Shunt off valve between buchloz and conservator TERMINATION HV-3 Pole single glands cable box suitable for reception of one No. 3 core upto 120 sqmm HT XLPE cable including compound for filling the cable end box with aluminium lugs / thimble. LV- 4 Pole 3 glands cable boxes suitable for 3 Nos. 240 sqmm 3.5 core Polyvinyl chloride cable having extended copper bars of requisite Capacity from LT bushing for making connections with cable including cost of aluminium lugs, thimbles LV : Neutral suitable cable Box for earthing provided.

Erection of MS Angle 50 x 50 x 6 mm, M.S. flat and nuts and bolts including cutting, bending to the required shape drilling holding carriage, painting loading and unloading complete in all respect.

Supply and erection of 120 Sqmm 3.5 core Armd. underground cable loose in existing pipe or trenches complete in all respect upto the entire satisfaction of Engineer in charge of the work.

Supply and erection of 25 Sqmm 3.5 core Armd. Cable underground cable loose in existing pipe or trenches complete in all respect upto the entire satisfaction of Engineer in charge of the work.

Supply and erection of 400 Sqmm 3.5 core Armd. underground cable loose in existing pipe or trenches complete in all respect upto the entire satisfaction of Engineer in charge of the work.

Supply and erection of 50 Sqmm 3.5 core Armd. underground cable loose in existing pipe or trenches complete in all respect upto the entire satisfaction of Engineer in charge of the work.

Supply and erection of XLPE (E) 11 KV HT alluminium armoured cable ISI marked in existing pipe / trenches / surface with all labour and material required to complete the job in all respect up to the entire satisfaction of Engineer-in-Charge of the work. (i) 120 Sqmm 3 Core XLPE cable

Supply and erection of lightening Arrestor Model SDU ALPRO make suitable for 11 KV 3 Phase 50 Hz grounded neutral system comprising of Speek gap type ( Quench gap type ) in series with non liner resister element housesed in horizontally Scale porcelain bushing with line and ground terminal along with mounting clamps Conforming to ISS 3070 (Part-1) of 1985 with latest amendment with all labour and material required to complete the job in all respect utpo the entire satisfaction of Engineer-in-charge of work.

Providing and fixing of wire mesh jali around the transformer of size 4`x 8` made out of 75 x 25 x 3.25 mm jali fixed with angle iron frame made out of M.S. angle 50 x 50 x 6 mm support of M.S. flat 50 x 6 mm and fixed in C.C. Block 1:2:4 including cutting, welding etc. as per drawing complete in all respect upto the entire satisfaction of the Engineer-in-Charge..

S.S. Enterprises

Janta Electric Store

DEVENDER KUMAR CONTRACTOR