80998 Adn Altn and Spl rep to 48 Type A DUs in srinagar colony Bldg No.P-47 P-170 P-199 at Port Blair

Amount

Demolition of cement concrete (unreinforced) in ground floors and pavings n.exc 15cm thickness ( below or above ground level) all as specified and as directed.

Taking down cement plaster of any description on brick or concrete surfaces etc including racking out joints, hacking for key, scrubbing down with water etc. all as specified and as directed.

Dismantling floor, hearth or wall tiles including cement mortar bedding(but not backing) and removing serviceable tiles to stores and rubbish off the premises all as specified and as directed.

Taking down chowkats or frames(without taking off shutters from the frame) area exc 1.5 Sqm but n.exc 4.0 Sqm each all as specified and as directed.

Taking down chowkats or frames (without taking off shutters from the frame) area n.exc 1.5 Sqm each all as specified and as directed.

M&L 25mm thick cement concrete type B-1, 1:2:4 (20mm graded aggregate ) as in flooring finished even and fair for correction of slope all as specified and as directed.

Dismantling of stone slabs and tiles of any description or thickness in floors, aprons and laid bedded and pointed in any mortar etc all as specified and as directed.

M&L Granite (of any type) tiles 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete over Screed bed or bedding layer of mortar 15 mm thick in CM 1:4 for laying floor finishes all as specified and directed.

M&L 20mm thick Granite (of any type) tiles machine cut, in skirting/ dado laid over cement screed 15mm thick cement screed in CM 1:4 and jointed with grey cement paste, and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete all as specified and directed

M&L for hardcore of gauge not exceeding 63 mm of broken stone, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface all as specified and directed.

M&L for 75mm thick Cement concrete type D-2, 1:4:8 (using 40 mm graded stone aggregate) in sub base of flooring/ hard standing finished even & smooth without using extra cement all as specified and directed.

M & L for coloured chequered cement concrete tiles 30 cm x 30cm x 25mm thick, set and jointed neat cement slurry and pointed with With mixture of white & grey cement in equal proportions & no pigment, over and including 20 mm thick screed bed or bedding layer in cm 1:6 etc. complete all as specified and directed.

M & L for coloured chequered cement concrete tiles 30 cm x 30cm x 25mm thick, set and jointed neat cement slurry and pointed with With mixture of white & greycement in equal proportions & no pigment, over and including 10 mm thick plaster or in cm 1:4 etc. complete all as specified and directed.

M&L Non-skid cerarmic coloured tiles 7 to 8 mm thick (Square/rectangular) area of each tile 0.11 Sqm but n.exc 0.18 Sqm, in neat cement slurry and pointed in white or coloured cement with pigment to match over 15mm thick screed bed in cement mortar (1:6) all as specified and directed.

All as per item No14 above but in skirting/dado laid over 10mm thick cement screed in CM 1:4 complete all as specified

M&L Glazed ceramic coloured/printed tiles (450X300mm) x 6-7mm thick on vertical surfaces as in skirting/dado,set and jointed with neat cement paste and pointed in white/coloured cement to match the shade of tiles over 10mm thick rendering in cement mortar 1:3 complete all as specified and directed.

Demolition of Precast Concrete work built in Cement Mortar including all quoins arches pillars etc complete all as specified and as directed.

M&L Pre-cast cement concrete block masonry Type C1 1:3:6 (20mm graded aggregate) with solid blocks, exc. 10 cm in width and setting in cement mortar 1:6, complete all as specified and directed

M&L for precast cement concrete block masonry with solid Type C1 1:3:6 (20mm graded aggregate as per IS 383) of 10cm in width and setting in CM 1:6 complete all as specified and directed.

M&L 15mm thick rendering on brick work or concrete surfaces in cement mortar 1:6 finsihed the surfaces even and smooth without using extra cement complete all as specified and directed.

M&L rendering 5mm thick in CM 1:3 on fair faces of brick work or concrete surfaces in ceiling complete all as specified and directed.

M&L15mm thick rendering on brick work or concrete surfaces in cement mortar 1:4 finsihed surfaces even and smooth without using extra cement complete all as specified and directed.

M&L for preparing newly plastered wall surfaces and applying two coats of oil bound distemper over a coat of alkali resistant primer complete all as specified and as directed.

M & L for preparing old plastered wall surfaces and applying one coats of oil bound distemper complete all as specified and as directed.

M & L for preparing newly plastered ceiling surfaces and applying two coats of oil bound distemper over a coat of alkali resistant primer complete all as specified and as directed.

M & L for preparing old plastered ceiling surfaces and applying one coats of oil bound distemper over complete all as specified and as directed.

M&L Preparation of newly plastered surfaces of wall & applying two coats of acrylic emulsion based premium quality exterior antifungal paint on wall surfaces over a coat of primer all as per manufacturer's instruction and as specified and as directed.

M & L for Preparation of old plastered surfaces of walls and applying one coat of acrylic emulsion based premium quality matt finish exterior antifungal paint as per manufacturer's instructions complete all as specified and as directed

M&L 40mm thick cemnt concrete type B-1, 1:2:4 (using 20 mm graded aggregate) as in floorings , finished even and smooth without using extra cement complete all a specified and directed.

M&L 50mm thick PCC 1:3:6 Type C-2 using 20mm crushed stone aggregate as in plinth protection and like finished even and smooth without using extra cement complete all a specified and directed.

S&F 38mm width of strip glass dividing strips, 3mm thick and inserted in position to confirm to design.

S&F solid PVC door frame of size 50mmx47mm made out of 5mm wood grain printed PVC sheet reinforced with MS square tube in opening as per specification and drawing.

S&F factory made solid panel PVC Door shutter 30mm thick (Style) consisting of frame made out MS frame shall be covered with heat moulded wood grain printed PVC 'C' channel having PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and woodgrain printed PVC sheet for top rail, lock rail, & bottom rail; Panneling of colour PVC sheet to be fitted in the M.S. frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification and drawing.

S&F pressed steel frames,size 105x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc. complete as specified.

S&F pressed steel frames,size 125x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc. complete ,as specified.

Providing cement concrete type C-0 1:3:6 (12.5 mm graded agg) as for pressed steel chowkhats complete as specified and directed.

S&F second class hardwood 35mm thick Plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete as specified and directed.

S&F Glazed and skeleton shutters second class hardwood 35mm thick, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats all as specified and directed

S&F mild steel Framed work such as grills, framed guard bars, ladders railings, frame of water tanks etc confirming to Fe-410 or Fe-310 as specified and directed.

M&L two coats of synthetic enamel painting on wooden surfaces over a coat of pink primer including preparation of newly untreated surfaces complete as specified and as directed.

M&L Painting two coats of synthetic enamel paint over a coat of red oxide including preparation of new steel surfaces of any description over 10cm in width or grith not other wise described. Complete all as specified and directed.

S&F 150mm aluminium anodised barrel tower bolts of extruded section and fixed.

S&F 250mm aluminium alloy anodised sliding bolts with hasp, staple and fixing clips of sheet, cast or extruded section fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed complete as specified and directed.

S&F 250mm mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed all as specified and directed

S&F butt hinges, 100mm medium weight, cold rolled mild steel as specified and directed.

S&F 125mm aluminium handles, cast type , anodised as specified and directed.

S&F Door helical spring mild steel 300mm, ordinary rat tail rod pattern including roller and roller plate complete.

Taking down eaves gutter and rain water pipes (of any size and pattern), incl all fittings and, heads, shoes, bends, swan-necks, etc incl cleaning or refixing or removal to store (measured overall as fixed along the centre line over fittings and accesories)

S&F 110mm bore PVC (SWR) soil, waste and vent pipe, in any length , with rubber joints, laid in trenches or in floors complete as specified and as directed.

S&F PVC (SWR) 110mm dia bend and double T equal or unequal at Junctions of any radius complete as specified and as directed.

S&F 20mm bore Brass ball valve with polythene float and fly nut fixed in repairs complete as specified and as directed.

Taking up or down steel tubing 15mm bore and connections, including cleaning for refixing or removal to store.

All as per item No 53 above but 20 mm bore.

All as per item No 53 above but 32 mm bore

S&F 15mm GI tubes, medium grade galvanised, with all fittings and fixed complete to walls and ceilings or laid in floors.

All as per item No 56 above but 20mm bore.

All as per item No 56 above but but 32mm bore.

S&F PVC valve less, syphonic action duel type low level flushing cistern of capacity 10 Ltrs with inlet, ball valve, float and handle and fixed to IWC on existing brackets, fixed in repairs complete as specified and directed.

S&F in repair vitreous china wash basin, white, flat back, size 550 x 400mm, fixed on existing brackets incl 32mm bore MS CP waste coupling complete as specified and as directed.

S&F viterous china squatting pan orissa pattern , size 580x 440mm white, interged foot rest including connection to trap and to flush pipe, anti syphonic pipe etc complete making good to floor complete as specified and as directed.

S&F CI floor traps 110mm bore with stainless steel grating including jointing to waste pipe in cement concrete 1:2:4 type B-1 complete as specified and as directed.

S&F in repair Rotational moulded polyethylene water strarge tanks 1000ltr (Cylinderical vertical with closed top) hoisted and fiexed in position all as per specified in SSR Pt-1.

S&F 25mm dia aluminum powder coated best quality curtain rails with fixing brackets in both ends complete all as specified and as directed.

S&F in repair decorative globes for curtain rails to be fixed at both end

S&F in repair brass chromium plated over head shower rose with arm 125 mm size with long body with swivel joint including fixing to steel pipe or union, complete all as specified and as directed.

S&F in repair Sinks with drainage board made of stainless steel 1mm thick for kitchen with plug washers, waste pipe and coupling includind bedding in cement mortar, two coat iron fixing bracket of required size and connecting union to pipe over all size 915mm x 460mm bowl size 410mm x 330 mm x 160mm,complete all as specified and as directed.

S&F in repair Waste pipe any dia (32/40mm) complete as specified and as directed.

S&F in repairs 15 mm dia bore fancy type pillar taps ,cast copper alloy chromium plated screwed down high pressure with or without lettered 'Hot' or 'Cold' with capstan head, screwed for iron pipes or for union and fixed, complete all as specified and as directed.

S&F in repairs brass chromium plated tubular towel rail, 20mm dia D-type, 60cm long between flange complete as specified and as directed.

Supply only PVC connections 15mm size with PTMT nuts of length 450mm complete all as specified and as directed.

S&F in repair 15mm bore stop valve/angle valve cast copper alloy chromium plated fancy type screwed down, high pressure, with crutch or butter fly handles fixed in repairs

S&F in repair Gun-metal, globe or gate valves with iron wheel head, screwed both ends for iron pipe 20mm bore all as specified and directed.

S&F in repair Gun-metal, globe or gate valves with iron wheel head, screwed both ends for iron pipe 32mm bore all as specified and directed.

S&F in repair 15mm Bib taps chromium plated cast copper alloy, fancy type with crutch or butterfly handle screwed down screwed for iron pipe or for brass ferrule and fixed 15mm bore complete all as specified and directed.

M&L for PCC 1:2:4 type B-1 (20mm graded aggregate) as in levelling course for slope correction of existing RCC roof surfaces including cleaning the roof surfaces and removing existing APP based membrane removing all foreign materials by wire brushes/ brooms/ water jet as specified

M&L providing APP based polymeric membrane minimum weighing 3Kg/Sqm and minimum 3mm thick reinforced with polyster non woven fabric (wt not less than 150 gms/Sqm ) land on after applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.2Kg per Sqm by forced application including one coat of aluminium paint over the top surface complete all as specified.

M&L dual coat of aluminium paint over the top surface of APP on roofs complete all as specified.

M&L applying a coat of blown type bitumen at the rate of 1.50 kg per sqm and binding with clean dry sand @ 0.05 cum per sqm complete all as specified.

S & F Anodised Aluminium frames for partitions, doors Windows and Ventilators with one or more rebates incl jointing cleat for fixing etc and aluminium anodised skeleton windows & ventilator shutter fixed with glass or gauge, side hung type without sash bars using standard aluminium section incl necessary jointing cleats, glazing clips, rubber packing anodised aluminium snap beadings screws, anodised aluminium fittings such as handles stainless steel adjustable friction stay hinges etc complete all as specified incl fixing of MS grills / aluminium grill, prelaminated particle boards, glazing to window frame aluminium wire cloth fixed to aluminium frame all as specified and directed by Engineer-in-Charge. NOTE: (i) Payment under this item will be make only for the cost of aluminium section. However unit rate quoted shall deemed to include cost of rubber beading, fittings such as handles, SS friction stay hinges and fixing of 5mm thick glass, prelaminated particle board and grills etc. (ii) Supply only sheet glass,particle board, aluminium wire cloth, MS grills and aluminium grill be measured and paid separately. (iii) Weight of aluminium handle & SS hinges shall not be accounted for payment purpose .

Supply only sheet glass 5.00 mm thick in square n.exc.0.50 sqm in each pane complete all as specified and as directed.

Supply only anodised aluminium 'XPM' 1.50mm x 3.00mm size for mosquito proofing 22 gauge thick complete all as specified and as directed

Supply only aluminium anodised grill DG (102) (10mm in width) of decogrille weight not less than 3.26 Kg per square metre, all as specified and directed

M&L for providing cement concrete type B-1, 1:2:4 (using 20mm graded aggregate) as in coping, benching, and similar works slightly rounded or chamfered angles and throating including necessary form work as directed

M&L for two coat of synthetic enamel paint over a coat of priming paint plaster coat and prepration of untreated surface of concrete all as specified and directed

Demolition of RCC work of any description and any position complete all specified and as directed.

M&L for precast RCC 1:2:4 type B-1 using 20mm graded stone agg as in cover slab and like except set in cement mortar 1:4 complete incl necessary form work complete all as specified and as directed.

M&L mild steel TMT bars 6-8mm dia bar cut to length, bent to shape required including cranking, bending spirally for hoping for fencing posts and binding with mild steel wire (annealed) not less than 0.9 mm dia all as specified.

M&L Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for handles etc and hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips all as specified

S&F door eye with 180° crystal clear lens for safe secure home fitted in pannel door with appropriate hole all as specified and directed by Engineer in Charge

S&F of 150mm Floor door stoper of aluminium alloy and tounge, anodised, with hard drawn steel spring, fixed in door.

Taking down scrubs/vegetation growth from crevices completely upto any height with all safety equipments all as specified and directed

S&F in repair soap dish, brass, chromium plated fixed to wall with brass chromium plated screw, complete all as specified and as directed.

M&L Rendering 15mm thick with WPC on walls as well as on sunken floors in CM 1:3 finished even and smooth using extra cement complete all as specified and as directed.

Supply only integral water proof compound.

Applying evenly a tack coat of hot blown bitumen 85/25 at the rate of 1.2 kg per sqm over a coat of bituminous primer at the rate of 0.3Kg/Sqm incl. cleaning of the surfaces complete all as specified and as directed.

M&L PCC 1:3:6 type C-2 using 40mm graded brick aggregate as filling under (sunken slab) floors complete all as specified and as directed.

Removing loose and broken concrete by chiseling/ mechanically etc from the roof slab, coloumn, beam and similar structural members cutting edges, cleaning the dismantled portion with wire brush etc to make the reinforcement naked and remove dust, dirt and other foreign particle etc and washing with clean water with pressure and removing rubbish off the premises to a distance not exceeding 50 mtrs and including necessary safety precautions and scaffolding up to a height of 12 mtrs complete all as specified and as directed by Engineer- in- charge.

M/L for applying IPH RB -107 polymer based rust-remover (pH value –12 ) and applying IPH RB -167 Polymer based rust preventive (pH value-9) to all exposed reinforced bars.

M/L for reinforced deformed bars 10mm dia and over cut to length cranking bending spirally or hopping ends MS wire annealed not less than 0.9mm dia complete all as specified and as directed.

M&L for cutting out existing cracks in concrete surfaces / masonry wall / RCC slab, forming a 'V' Groove of 25mmx40mm size, cleaning the groove thoroughly with air blower, priming the groove with mixture of IPH-CC Resin & Hardener manufactured by Harjas Coatings & Polymers or equivalent proportions using spray gun/brush, filling the groove with putty of IPH-CC Resin, Hardener & admixture manufactured by Harjas Coatings & Polymers or equivalent in M/s Fosroc Chemicals India [P] Ltd. or Dr. Fixit, mixed in 1:1:4 ratio, and finally applying a seal coat of same as of primer coat with brush complete all as per manufacturer's instructions and as directed.

M/L for applying one coat of epoxy bonding coat as per manufacture's instruction to bind old concrete surfaces of soffit of slab, coloumn, beam and similar structural members for new gunited / cement surface. Make : IPH 21 EB of Harjas Coatings & Polymers / Nitobond EP of FOSROC or equivalent make in Dr. Fix it of Pidilite Industries / MC Bauchemie / BASF

M & L for non shrink, cementatious Micro concrete using Renderoc RG manufactured by M/s. Fosroc Chemicals India [P] Ltd. or its equivalent in Dr. Fixit or IPH-411 of M/s Harjas Coatings & Polymers modified with 12.5mm graded crushed stone aggregate in the ratio by weight (18kg aggregate: 25kg micro concrete) respectively as per manufacturer's instructions, as in sides and soffits of beams,jacketing of columns, ,roof slab and similar structural members including necessary form work for fair finished surfaces use and waste of water tight form work to facilitate pouring of micro concrete complete all as per manufacturer's instructions and as directed by Engineer- in- charge.

Drilling of holes of size 10/12 mm dia to a depth of of 50 to 100 mm into the concrete surface/ crack using rotary cum hammer drill and fixing PVC/ brass nozzles with IPH 21 epoxy based sealent to facilates grouting. The spacing of nozzles shall be as decided by Engineer-in-Charge.

M & L IPH 21 (G) high strength epoxy based for grouting over the concrete surface by injecting through the nozzles to strength the weak concrete. The system should have suitable viscosity which will enable it to soak into weak concrete and on subsequent polymerisation bind the loose and weak concrete. The minimum requirements of epoxy based grout material are as under: 1.Compressive strength @ 7 days : 60 N/sqmm 2 Tensile strength @ 7 days : 20 N/sqmm 3. Pot life : 30 to 45 min

M&L for drilling 15mm dia holes in to RCC slab / wall / Column /beams to a depth of 100 to 150mm & provide shear connector of 12mm dia rod of length of 150mm bent to "L" shape with 75mm to be embedded in hole & 75mm to be used as dowel, fixed with polyster resin grout mixed mechanically and pour the same into the hole and insert the shear connector and finish the top; allow the same to set complete all as per manufacturer's instructions and as directed. [Make of grout : 'Lokfix S' of make : M/s Fosroc chemicals India (P) Ltd. or equivalent in M/s Harjas Coatings & Polymers / M/s Pidlite Industries Ltd. / M/s Sika India Pvt Ltd / M/s Structural Water proofing Co Pvt Ltd / M/s BASF India Ltd].

S&F for Hard drawn steel wire fabric weight not exceeding 4 kg per square metre, cut to lengths, bent to shape required and tying with and including mild steel wire (annealed) not less than 0.9mm in dia welding to existing reinforcement complete all as specified and as directed by Engineer- in- charge.

M & L for pressure guniting 40 mm average thickness at a pressure not less than 6kg/ sqcm to all affected RCC structures in cement mortar 1:3 duly modifying with mixture of Nitobond SBR of FOSROC @ 7 litres per 50 kg of cement or IPH-CC resin and IPC-CC hardner of make Harjas Coating & polymers in equal proportion @ 5% of weight of cement or equivalent in Pidilite industries Ltd and including necessary safety precautions and scaffolding, Tools and plants complete all as per manufacturer's instructions and as directed by the Engineer-in-Charge.

M&L for applying polymer modified cement mortar rendering 15mm average thick in CM 1:3 on gunited surfaces duly mixing polymer modifier 'Nitobond AR' of make: M/s Fosroc Chemicals India (P) Ltd. @ 10 Ltr per bag of cement or equivalent in M/s Harjas Coatings & Polymers @ 5% by wt of cement / M/s Pidilite Industries complete finished even and smooth without using extra cement all as specified and as per manufacturer's instructions.

Supply only IPH-CC @ 5% by weight of cement to use in guniting.

M & L for applying curing compound [Concure WB of M/s. Fosroc Chemicals India [P] Ltd. or its equivalent in Dr. Fixit or Harjas Coatings] on newly gunited/ concrete / plastered surface complete all as per manufacturer's instructions and as directed by Engineer- in- charge.

M&L for applying first layer of IPH 21 Resin & IPH 21 Hardner in 1:1 ratio. Fix Polymer cloth reinforcement of 200 gms per sqm on the top of wet coat. Apply second layer of IPH 21 Resin & IPH 21 Hardner in 1:1 ratio or equivalent in M/s Fosroc Chemicals India [P] Ltd. or Dr. Fixit all as per manufacturer's instructions and as directed.

M&L for applying two coats of water proofing treatment on concrete/masonary wall surfaces of any description on new /old plastered surface with IPH 21of M/S Harjas Coating & Polymers / Brush Bond of FOSROC / Equivalent of Dr Fixit of Pidilite Industries Ltd as specified and as directed by Engineer-in-Charge.

Dismantling wrought iron or mild steel work of any description not otherwise provided.

M & L Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc.con- forming to Fe.290.Gde-E-165 complete all as specified and as directed.

Dismantling Plain or corrugated steel sheeting any gauge, thickness, including Nainital or similar pattern roof coverings in roof covering all as specified.

S&F pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified.

S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as in ridges, hips, valley gutter, drip, and straight flashing all as specified and as directed.

S & F Aluminium flat iron work in, wind ties screwed as directed, including all necessary drilling, bolting or riveting etc., and similar work

Dismantling Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets

S&F for aluminium anodised snap grid false ceiling of standard aluminium section such as wall angle of size 38mm x 25mm x 2.4mm weighing 0.36 Kg/Rm main/cross tees of size 36.5mm x 25mm x 1.4mm weighing 0.24 Kg/Rm, grid size n.exc. 610 x 610mm suspended with 4mm dia GI wire at interval n.exc. 600mm centre to centre for main & cross tees fixed to roof slab roof truss fixed with suitable size MS hook and fastening bolts etc including 'E' board classic 4mm thick oceanic sheet of size n.exc. 610 x 610mm size fixed in ceiling with clips to aluminium snap grid all as specified and directed.

Dismantling water tanks, cleaning and removing all scale and dirt, etc from tanks and rom mouths of circulating pipe and refixing to same place all as specified and directed

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc

Taking down unserviceable submain wiring alongwith batten/PVC/steel conduits etc and making good disturbed surfaces of walls/ floors to match the existing surfaces all as specified

Taking down unserviceable main switches ,DBs and making good disturbed surfaces of walls/ floors to match the existing surfaces all as specified

Taking down fan, sealing cable end, dismantling blades and removing fan and blades to store

M&L for point wiring with 1.5 Sqmm (nominal area) FRLS, single core PVC insulated 1100 Volts, grade multistranded copper conductor unsheathed in and including concealed PVC conduit 20 mm dia or higher and conduit fittings and accessories including one green colour 1.5 Sqmm PVC insulated unsheathed multistranded copper conductor cable FRLS grade as earth wire up to common earth and connected to earth dolly complete for one light/fan/6A switch socket controlled by one way switch all as specified and directed by Eng.-in-charge . Note:- GI metal flush box for modular switches and inner plate and outer plate for modular switch shall be measured and paid separately and rate include cutting chases for conduits and sinking's for boxes and making good to walls, floors etc. in recessed or concealed conduit wiring complete all as specified and as directed by Engr-in-Charge.

One light point controlled by one one way switch complete all as specified and as directed by Engr-in-Charge.

One fan point controlled by one switch complete all as specified and as directed by Engr-in-Charge.

One switch socket 5 pin 5/6 Amps flush type on independent board complete all as specified and as directed by Engr-in-Charge.

One switch socket 5 pin 5/6 Amps flush type on same board complete all as specified and as directed by Engr-in-Charge.

One exhaust fan point controlled by one switch complete all as specified and as directed by Engr-in-Charge.

One two way point controlled by 2 two way switch complete all as specified and as directed by Engr-in-Charge.

One bell/ buzzer point controlled by one push button complete all as specified and as directed by Engr-in-Charge.

All as per item No 127.01 above but with 2.5 sqmm FRLS cable for one socket 5 pin 15Amps flush type on independent board with including earth wire of size 2.5 Sqmm complete all as specified and as directed by Engr-in-Charge.

All as per item No 127.01 above but with 4.0 sqmm FRLS cable for one socket 5 pin 15Amps flush type on independent board with including earth wire of size 4.0 Sqmm complete all as specified and as directed by Engr-in-Charge.

All as per item No 127.01 above but number 04 light point (Security Light) controlled by one switch /MCB complete all as specified and as directed by Engr-in-Charge.

Supply and fix Modular switch 1 way 6A, 1 module complete all as specified and as directed by Engr-in-Charge.

Supply and fix Modular switch 1 way 16A, 1 module complete all as specified and as directed by Engr-in-Charge.

Supply and fix Modular switch 2 way 6A, 1 module complete all as specified and as directed by Engr-in-Charge.

Supply and fix Modular Bell push 6A 1 module complete all as specified and as directed by Engr-in-Charge.

Supply and fix Bell Multi Music type complete all as specified and as directed by Engr-in-Charge.

Supply and fix Socket, 6A - 2/3 pin combined 2 module, complete all as specified and as directed by Engr-in-Charge.

Supply and fix Socket 6A/16A - 2/3 pin combined 2 module complete all as specified and as directed by Engr-in-Charge.

Supply and fix Fan step regulator, 60 W - 2 module complete all as specified and as directed by Engr-in-Charge.

Supply and fix White cover plate with frame,2/3 module complete all as specified and as directed by Engr-in-Charge.

Supply and fix White cover plate with frame,4 module complete all as specified and as directed by Engr-in-Charge.

Supply and fix White cover plate with frame,6 module complete all as specified and as directed by Engr-in-Charge.

Supply and fix White cover plate with frame,8 module complete all as specified and as directed by Engr-in-Charge.

Supply and fix White cover plate with frame,12 module complete all as specified and as directed by Engr-in-Charge.

Supply and fix Metal flush box 2/3 module, made of MS chromium platedcomplete all as specified and as directed by Engr-in-Charge.

Supply and fix Metal flush box 4 module, made of MS chromium plated complete all as specified and as directed by Engr-in-Charge.

Supply and fix Metal flush box 6 module, made up of MS chromium plated complete all as specified and as directed by Engr-in-Charge.

Supply and fix Metal flush box 8 module, made of MS chromium plated complete all as specified and as directed by Engr-in-Charge.

Supply and fix Metal flush box 12 module, made of MS chromium plated complete all as specified and as directed by Engr-in-Charge.

Supply and Fix Ceiling rose, 3 phase/PVC/polycarbonate, isolated body complete all as specified and as directed by Engr-in-Charge.

Supply and fix Lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings complete all as specified and as directed by Engr-in-Charge.

Material and labour for concealed sub main wiring with 6 runs of single core 4 Sq mm phase,neutral & earth 1100 V grade PVC insulated unsheathed FRLS grade copper conductor cable single core multistranded ISI marked (IS-694:1990) drawn through and including suitable size PVC conduit ISI marked including connected accessories such bend support etc laid in wall/roof/ floor etc complete all as specified and as directed by Engr-in-Charge. Note :-4 runs of 4 Sq mm copper cable for phase and neutral and 02 runs of 4 Sqmm copper cable for earth and one run of PVC conduit along with accessories shall be measured as one run in this item.

Supply and fix Decorative, wall mounting, champagne gold finish fixture with plastic body suitable for 9 W LED lamp B22 base confirming to cat No LHFOECE1TZ1O014 of Havells or Equivalent in Crompton/Luker/Philips including 9W bulb. complete all as specified and as directed by Engr-in-Charge.

Supply & fix LED tube light along with fixture, 20 W complete all as specified and as directed by Engr-in-Charge. Make :- Havells/Crompton/Luker/Philips

Supply & fix LED down lighter, 9 W complete all as specified and as directed by Engr-in-Charge. Make :- Havells/Crompton/Luker/Philips

Supply & fix LED tube light along with fixture,10 Wcomplete all as specified and as directed by Engr-in-Charge. Make :- Havells/Crompton/Luker/Philips

Supply and fix LED bulb 0.5W complete all as specified and as directed by Engr-in-Charge. Make :- Luker Cat Part No LBCOL05 or Equivalent in Havells/Philips/Crompton as approved by GE.

S&F in repair energy efficient new 15 liters capacity Rated Power 1kW electrical geyser white/half white, copper container inner tank with fiber reinforced body (FRB) puff insulation for both inner tank & for hot outlet copper connection pipe with all in built in safety accessories like thermostat/automatic thermal cut out with ON /OFF /CUT out indicators all pre-wired and additional safety accessories like pressure release valve/pressure reducing valve, non return valve, rate shall be including for new PVC heavy duty pipe with brass ferrule fitting for HOT and COLD water connections fixed in same or new location as ordered/required as per manufacturers instruction with suitble size nuts & bolts, making necessary connection & testing on completion inclu taking down old unsv geyser and making good to the disturbed suface of wall complete all as directed. Note : The old unserviceable geyser shall be deposited to MES store yard. Make : Havells Cat No GHWAPXTWB015 or Equivalent in Bajaj/Crompton as approved by GE.

Supply and fix RCBO of 2 pole , 20 Amp rating with sensitivity of 10 mA suitable for 240 Volts complete all as specified and as directed by Engr-in-Charge.

Supply and fix MCB metallic Plug &Socket with provision for MCB/RCCB/RCBO and steel enclosure including MCB 20 Amps 'C' curve 10KA complete all as specified and as directed by Engr-in-Charge.

Supplying and laying of CPVC pipes SDR 13.5 pipes & plain CPVC SDR 11 fittings fittings on walls/ceiling or laying in floors complete all as specified and as directed by Engr-in-Charge.

Supply and Fix Stop valves, cast copper alloy,screwed down, high pressure, with crutch or butterfly handle,screwed both ends for Iron pipe/CPVC Pipe or for unions. complete all as specified and as directed by Engr-in-Charge.

Supply and Fix Bib tap standard of PTMT any colour high pressure screwed for iron/CPVC pipe and fixed complete all as specified and as directed by Engr-in-Charge.

M&L for sheet metal board complete with locking arrangement, fabricated out of 2.00 mm thick MS sheet of size 1.5x1.2X0.20 Mtr flushed in wall including mounting arrangements for energy meters and one MCB TPN DB /MCCB TPN DB 4/6 way, front opening, painting with two coats of synthetic enamel paint over a coat of red oxide primer on internal and external surfaces and making good damaged surface complete including taking down old unserviceable rusted sheet metal enclosure, from the building and all as specified and directed by Engineer-in-charge. Note:- 1. Dismantle all energy Meters (7/9 Nos) and MCCB TPN/MCB TPN DBs(1/2 Nos) and kept in safe custody and refixing the same day after fixing the metal board. 2.Concealed the DBs on wall all including make in good and matching with existing surface

Supply and fixing as in repair of MCCB DB TPN 4 way IP-43 made of sheet steel phos phatised, powder painted with bus bar, neutral link, earth bar and Din rail ,415 Volts with double door with MCCB incomer and MCB outgoing . Make : Legrand Cat part No 507751 or Equivalent in L&T/Schiender/ABB/siemens as approved by GE. Note : MCCB and MCB will measured and paid separately

Supply and fix MCB SP 6-32A 10KA, C'curve complete all as specified and as directed by Engr-in-Charge.

Supply and fix MCB SPN 6-32A 10KA, C'curve complete all as specified and as directed by Engr-in-Charge.

Supply and fix MCB SPN 40-63A complete all as specified and as directed by Engr-in-Charge.

Supply and fix Sheet steel factory made double door, powder coated MCB DB with bus bar 200Amps,Neutral link, Earth bar, double door type SPN 12 Way 220 Volt, MCB as a Incomer complete all as directed. Make : L&T / Legrand / Schneider / ABB

Supply and fix 4 Pole MCCB 100 to 125 Amp, 50 Hz, 415 V with rupturing capacity 25 KA complete all as specified and as directed by Engr-in-Charge.

Supply and fix LED street light 25 W IP 65 complete all as specified and as directed by Engr-in-Charge. Make :- Crompton/Luker/Havells/Philips

M&L for earthing complete with Galvanised steel earth plate electrode 60 cm x 60 cm x 6 mm thick buried directly in ground (earth pit not less than 2.25 mtr deep below GL) with top edge of earth plate not less than 1.5 Mtr below normal ground level, earth plate surrounded from all sides by 15cm thick and packed layer of charcoal dust and common salt filling in alternate layers and electrode connections by using Galvanised earth wire 4mm connected by means of bolts, nuts, check nuts and washer of galvanised iron or steel, provision of 15 mm dia GI pipe medium grade for protection of GI earth wire and 20mm dia GI pipe medium grade for watering arrangement and PCC (1:3:6) , type C1 chamber, MS funnel, wire gauge, 50 mm thick RCC 1:2:4, type B1 earth pit cover with 6 Nos, 8 mm dia high strength deformed steel TMT bars on both ways including necessary excavation in any type of soil, returning, filling in, removal of surplus soil to distance n exc 50 mtr, provision of charcoal and salt complete all as shown in electrical plate No 3 of schedule Part-I Note :-The unit rate shall also includes for Wire mesh, funnel, excavation, PCC chamber pit, test point

Taking down unserviceable LT UG Cable complete all as specified and as directed by Engr-in-Charge.

Suppy and laying in trenches, fixed on walls, passing through pipes, jointing and testing of electric LT cables, PVC insulated, PVC sheathed, galvanised steel strip or wire armoured electric power cables of size 35 Sq mm 3.5 Core with stranded aluminium conductors 1100 Volts grade complete all as specified and as directed by Engineer-in-Charge Note: The quoted rate shall include Cable lugs, Cable Gland and joint kit (if required).

Supply & Laying of Telerex DWC (Double Wall corrugated) HDPE pipe ISI marked of outer dia of 77 mm and inner dia 63 mm polythylene including coupler & Bend with smoooth inernal and profiled external surface for non pressue under ground cable complete all as specified and as directed by Engineer-in-Charge Make : REX POLYEXTRUSION LTD or its equivalent as approved by GE.

S&F GI pipe of medium grade 40 mm dia all fitting fixture for fixing with wall and road crossing etc. complete all as specified and as directed by Engr-in-Charge.

Excavation in trenches any type of soil (soft/loose/hard/dense) not exc 1.5 mtr wide and not exc 1.5 mtr in depth for foundation, pipe, laying of cable etc not exc 10 Sqmtr on plan and not exc 1.5 mtr in depth and getting out complete all as specified and as directed by Engr-in-Charge.

Returning filling in, including spreading, leveling, watering and well ramming in layers not exceeding 25 cm in soft/loose soilcomplete all as specified and as directed by Engr-in-Charge.

Removing excavated materials (soil) to a distance not exceeding 50 meters and depositing where directed at a level not exceeding 1.5 meters above the starting point complete all as specified and as directed by Engr-in-Charge.

M&L for road cutting, removing of material , returning filling and PCC 1:2:4 for laying of LT UG cable /Galvanised Iron Pipe/Rex Pipe complete all as specified and as directed by Engr-in-Charge.

Taking Down old single Phase Energy meter and deposited to MES store Yard complete all as specified and as directed by Engr-in-Charge.

Supply & fix AC single phase static energy meter of accuracy class 1.0, 240 V 50 Hz with Backlit LCD display of rating 10 - 60 A (measures and displays KWH ,V, Current I, KW, pf last month history of KWH, MD in KW) with special features like TOD, temper logging, optical communication port display in absence of power with transparent hinge type box complete all as specified and as directed by Engr-in-Charge.

Supply & fix fans ceiling with brushless direct current motor (BLDC) complete with electronic type regulator and accessories 230 V,1200 mm sweep.energy efficient rated complete all as specified and as directed by Engr-in-Charge.

Supply & fix exhaust fans steel bpdy, copper winding AC single phase 230/ 240 V of size 300 mm sweep with louver complete all as specified and directed. Note:- old unservicable exhaust fan deposited to E/M store

M&L for cutting of hole through cement mortar brick wall including providing, fixing and removing shoring,cleaning,internal plastering and removing surplus hard core,rubbish not exceeding 50 mtrs including fixing of exhaust fan of size 250-450 mm complete all as specified and as directed by Engr-in-Charge.

AMR TRADERS

N Rathinam

CITY CONSTRUCTION COMPANYU

Sree Tirumala Enterprises

A.G.Construction

Hindustan Traders