8761/E8

Amount

Excavating in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth for foundation etc. or for shafts, well , cesspits, manholes, pier holes, cable etc etc. not exc 10 Sqm on plan and getting out in soft / loose soil. complete all as specified and directed.

Excavating in trenches not exceeding 1.5 m wide and exceeding 1.5 m but n.exc 3.00m in depth for foundation etc. or for shafts, well , cesspits,manholes,pier holes etc. not exc 10 Sqm on plan and getting out in soft / loose soil. complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 Cm as in soft / loose soil complete all as specified and directed.

Removing excavated material of soft / loose soil exc. n.exc 50m and depositing where directed at a level not exc 1.5 m above the starting point complete all as specified and directed.

Material and labour Plain cement concrete Type D2 (1:4:8) (using 40mm graded stone agreegate) as in foundation, filling and mass concrete complete all as specified and directed

Materials and Labour Treating the backfill in contact with foundation at the rate of 7.5 litres of emulsion per Square metre of vertical surface (Area of the sub structure in contact with backfill to be measured) complete all as specified and directed.

Materials and Labour Treating the top surface of filled earth at the rate of 5 litres of emulsion per Square metre of surface complete all as specified and directed.

Materials and Labour Treating the soil under plinth protection at the rate of 5 litres of emulsion per Square metre of surface area complete all as specified and directed.

Materials and Labour Treating the soil along with external perimeter of building at the rate of 2.25 litre of emulsion per metre of the perimeter wall complete all as specified and directed.

Materials and Labour Use and waste Formwork for rough finished surfaces to the sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified and as directed.

Materials and Labour Use and waste Formwork for rough finished surfaces to sides of pillars, posts, struts, piers, columns and stanchions of square or rectangular in section complete all as specified and as directed.

Materials and Labour Use and waste Formwork for rough finished surfaces to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc complete all as specified and as directed.

Materials and Labour Use and waste Formwork for rough finished surfaces to chullah hoods, chajjas, troughs and similar items including edges etc complete all as specified and as directed.

Materials and Labour Use and waste Formwork for rough finished surfaces to the soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and as directed.

Supply and fix TMT steel bars 10mm dia and over cut to length, bend to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips quality complete all as specified and directed.

Supply and fix TMT steel bars 6-8mm dia bars cut to length, bend to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips quality complete all as specified and directed.

Supply and fix TMT steel bars 6mm dia and over and upto 10mm dia bars as in stirrups, spacers and binders cut to length, bend to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips quality complete all as specified and directed.

Material and Labour Reinforced Cement Concrete (Design mix) M25 as in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed. NOTE : Formwork and Reinforcement shall be Measured and Paid for separately under relevant Items.

Material and Labour Reinforced Cement Concrete (Design mix M25) as in Columns, pillars, piers, posts and struts complete all as specified and directed. NOTE : Formwork and Reinforcement shall be Measured and Paid for separately under relevant Items.

Material and Labour Reinforced Cement Concrete (Design mix) M25 as in Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed. NOTE : Formwork and Reinforcement shall be Measured and Paid for separately under relevant Items.

Material and Labour Reinforced Cement Concrete (Design mix) M25 as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed. NOTE : Formwork and Reinforcement shall be Measured and Paid for separately under relevant Items.

Material and Labour Reinforced Cement Concrete (Design mix) M25 as in Chajjas complete all as specified and directed. NOTE : Formwork and Reinforcement shall be Measured and Paid for separately under relevant Items.

M&L Brick Work using fly ash bricks pulverized (Designation - 75 Kgf/Cm2) old size bricks straigth or curved on plan exc 6m mean radius built in CM (1:6) cmplete all as specified and directed.

Material and Labour Rendering 15 (10+5) mm thick in cement mortar 1:4 on fair faces of brick work or concrete surface in two layers, top layey of 05mm mixed with integral water proofing compound as per manufactturers instructions finished the surfaces even and smooth without using extra cement complete all specified and as directed. Note : - Water proofing compound shall be measured and paid separately as "Supply only" item under relevant item of these schedule.

Material and labour Rendering 15mm thick in CM 1:6 other than fair faces of brick or concrete surfaces and surface finished even and smooth with using extra cement complete all as specified and directed by Engr -in -Charge

Material and Labour Rendering 5 mm thick in Cement mortar 1:3 as in ceiling & bottom slab concrete surfaces finished the surfaces even and smooth without using extra cement complete all specified and as directed.

"Supply only" Liquid integral water proofing compound (ISI marked) complete all as specified and directed.

M&L Mild Steel Work in Tubular /hollow section as in Trusses and post including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS-4923 grade YSt.-240 complete all as specified and as directed.

M&L Rolled mild steel section as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates conforming to Fe-410-W (Gde-E-250) quality A complete all as specified and directed.

S&F Mild Steel Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment (Fe-290 Gde-E165) complete all as specified and directed.

Material and Labour for Mild steel Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165 complete all as specified and directed.

M&L Mild Steel Screw Bolts (machine made) 11mm to 15mm diameter of neck and length of bolt exc 22.5 Cm and not exc. 30 Cm with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, complete all as specified and as directed.

Supply and fix Galvanized iron pipe, 40mm bore, light grade with all fittings, laid in floor , walls for cable proction complete all as specified & directed.

Supply and fix Pre-Painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

Supply and fix Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall and ridge, fixed with self tapping screws complete all as specified and directed.

M&L False ceiling with 'E' board "Classic" , reinforced, designer series, board with HPSC of size 600 mm x 600 mm x 4 mm thick fixed on aluminium powder coated snap grid to support the boards/tiles with aluminium anodised main 'T' section 36mm x 25mm x 1.40mm cross tee 23.50mm x 23.50mm x 1.40mm thick and aluminium angle 25mm x 25mm x 1.40mm as on edges/sides including hanging arrangements with 6mm dia GI hooks and clamp and applying two coats of oil bound distemper over a coat of alkali resistant primer on exposed surfaces complete all as specified and as directed.

S&F for Solid PVC Door Frame of size 50mm x 47mm made out of 5mm wood grain printed PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening complete all as specified and directed.

S&F for Factory Made Solid PVC Moulded Door Shutter With Wood free EPS, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick 3D wood grain Moulded PVC Sheet Polyurethane painted on the front face & 2mm prelam PVC Sheet on back face, supplying & fixing in frame at site complete all as specified and directed.

Supply and fix Pressed steel frames of size 125mm x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified, supplied and fixed complete all as specified and directed. Note:- Pressed steel frame shall be filled with PCC type C1 ( 1:3:6, using 20mm graded crushed stone aggregates) and cost of same shall deemed to be included in the rate quoted by the tenderer in this Item.

Supply and fix 35mm thick, Flush shutters, solid core construction, with particle board core and plywood face panels, commercial type on both sides complete all as specified and directed.

S&F for 2nd class hardwood 35mm thick Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats as specified in SSR Part-I 2009.complete all as specified and directed.

Supply and fix Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and as directed.

Supply and fix Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete without glazing bars, dovetailed or welded complete all as specified and as directed.

S&F for Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

S&F Sheet Glass 3.0mm thick ordinary quality glazing with Wooden Beads or Oil Putty in Square or Rectangular, not exc. 0.50 Sqm, complete all as specified and as directed.

Material and Labour Plain cement concrete 1:3:6, type C-1 (using 20 mm graded stone aggregate) as in coping/ fencing and bed block complete all as specified and directed.

Supply and fix 200mm Stainless steel barrel tower bolts of extruded section complete all as specified and as directed.

Supply and Fix 300mm Stainless steel sliding door bolt with hasp, staple(bolt type) and fixing clip of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy complete all as specified and as directed.

Supply and fix 150 mm Stainless steel handles 'D' type complete all as specified and as directed.

Supply and fix stainless steel door stopper Overall length of cover plate 150 mm complete all as dirceted by Enginneer-in-Charge.

S&F 300mm, ordinary mild steel rat tail rod pattern springs including roller and roller plate complete complete all as specified and directed.

Material and Labour for 75 mm thick, plain cement concrete 1:4:8, type D2 (using 40 mm graded stone aggregate) as in sub base for flooring complete all as specified and directed.

Material and Labour for 25 mm thick, plain cement concrete 1:2:4, type B0 (using 12.5mm graded stone aggregate) as in sub base for flooring complete all as specified and directed.

M&L Non-skid Ceramic Coloured Tiles, 7.0mm to 8.0mm thick (square/rectangular), area of each tile exc 0.18 sqm but not exc 0.38 sqm in Floors, etc. Set and Jointed in Neat Cement Slurry and Pointed in White or Coloured Cement to match the Shade of the Tiles over 15mm thick screed bed (1:6) in cement mortar complete all as specified and as directed.

M&L joint free non skid ceramic coloured tiles 8-10mm thick (square/rectangular) area of each tile exc 0.18 Sqm but not exc 0.38 Sqm on Vertical Surfaces such as Skirting, Dados, Risers to Steps, etc., Set and Jointed in Neat Cement Slurry and Pointed in White or Coloured Cement to match the Shade of the Tiles over and including 10mm thick backing layer in cement mortar (1:4) complete all as specified and as directed.

M&L joint free non skid ceramic coloured tiles 7-8mm thick (square/rectangular) area of each tile exc 0.06 Sqm but not exc 0.11 Sqm in floor set and jointed in in neat cement slurry and pointed in cloured cement to match over and including 15mm thick screed bed in CM 1:6 complete all as specified and directed

M&L glazed ceramic coloured tiles 450x300x6-7mm in vertical surfaces set and jointed in in neat cement slurry and pointed in cloured cement to match over and including 10mm thick rendering in CM 1:3 complete all as specified and directed

Material and Labour for hardcore of gauge n.exc 63 mm of broken stone or boulders, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L Sand filling under floors or in foundations including watering and consolidation complete all as specified and directed.

Material and Labour for 100 mm thick, plain cement concrete 1:2:4, type B2 (using 40 mm graded stone aggregate) as in sub base of path/hardstanding cement complete all as specified

Materials and Labour 25mm thick rubber moulded prepolished coloured PCC chequerred tiles of size 400mm x400mm x25mm thick, set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles with and including 20mm thick screed bed in cement mortar 1:6 complete all as specified and as directed.

M&L for Preparation of new plastered surfaces and applying two coats of oil emulsion distemper (any colour/tint) over a coat of primer over and including 2 mm thick wall care putty (Birla/Asian) on wall surfaces including rubbing with emmery paper to make wall surface smooth and even complete all as specified and directed.

Materials and labour Preparation of newly plastered exterior wall surfaces of any description and applying two coats of exterior emusion paint of any colour / tint over a coat of primer with safety measure complete all as specified and directed.

Material and Labour Preparation of new steel surfaces of any description, over 10 Cm in width or girth and applying two coats of synthetic enamel paint of any clour / tint over a coat of red oxide primer complete all as specified and directed.

Material and Labour Preparation of new wooden surfaces of any description, over 10 Cm in width or girth and applying two coats of synthetic enamel paint of any clour / tint over a coat of pink primer complete all as specified and directed.

S&F for 20mm outer diameter CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and directed.

S&F for 25mm outer diameter CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and directed.

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels etc., and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exceeding 10 cm girth in brick walls etc complete all as specified and as directed.

Supply and fix Vitreous China squatting pan of ‘Orissa pattern’, size 580 mm x 440mm (white) with ‘P’ or ‘S’ trap, front or back inlet and foot rests, any pattern complete including provision of PCC bedding and connection to trap, and to flushing pipe, antisyphonage pipe, etc. complete including making good to floor all as specified and directed by the Engr-in-Charge.

S&F Vitreous china urinal flat back of size 305 x 305 x 440mm white with grating & union for discharge pipe including Urinal spreader of PTMT any colour for fixing with 15mm dia pipe (Minimum weight 60gms) but excluding flushing cistern, flush pipe & waste pipe but fixing only automatic flushing cistern with bracket flush pipe etc complete all as specified and directed.

S&F Vitreous China Colour Wash down Water Closet Pan (Pedestal Pattern) with "p" or "s" trap front or back inlet including fixing Bolts with and excluding 10 litre capacity low level Flushing Cistern matching with water closet colour with inlet ball valve float handle and providing 32mm dia PVC flush pipe including plastic water closet seat with flat botton cover (coloured) fixed with mild steel chromium plated or aluminium hinging device and making good disturbed Surfaces in Cement Mortar 1:3 and fixed, complete all as specified and as directed.

S&F Vitreous China Wash Hand Basin 550x400mm in size, White (Flat Back or Angle Back Type) with 32mm dia Brass Chromium Plated Waste Fitting, a pair of Cast Iron Brackets duly painted including Cutting and pinning in Ends, making good disturbed Surfaces in Cement Mortar 1:3, complete all as specified and as directed.

S & F 32mm bore PVC waste pipe flexible type including all cups and sockets with minimum length 800mm for any type/make/size for wash hand basins complete all as specified and directed

Supply and fixing 10 litre capacity low level PVC flushing cistern (any colour), syphonic action type, with inlet, ball valve, float, handle, fixed with cast iron bracket (of suitable size) and providing 32 mm dia PVC flush pipe and making all necessary connections complete as directed.

S&F for 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints fixed to wall complete all as specified and directed.

S&F for 110mm bore PVC (SWR) pipes double socketed, in any length with rubber ring joints fixed to wall complete all as specified and directed.

S&F PVC (SWR) bend any radius 110mm bore complete all as specified and directed

S&F PVC (SWR) junction single (single T) equal or unequal 110mm bore complete all as specified and directed.

M&L for diameter of outlet 75mm UPVC (SWR) floor trap plain with grating including jointing with solvent cement complete all as specified and as directed

S&F 3-in-1 wall mixer for Hot & Cold water supply with telephonic shower arrarengement, brass chromium plated fancy type, screwed down for 15mm bore iron pipe incl necessary fittings & fixtures etc. complete all as specified and directed.

S&F Central hole for Hot and Cold water supply basin mixer, brass chromium plated screwed down for iron pipes,including necessary fittings etc , complete all as specified and as directed.

S & F in for 15mm bore brass chromium plated Angular Valve with Wall Flange complete all as specified and directed.

S&F Brass chromium plated fancy type bib cock screwed for 15 mm bore of pipe etc. as in complete all as specified & directed.

S & F in repair for brass chromium plated two in one tap with Wall Flange screwed for 15 mm bore pipe complete all as specified and directed

S&F ABS Body chrome plated shower rose 125mm size including fixing to steel pipe or union complete all as specified and directed. Make-Essco (EOS-CHR-542A) or equivalent from Marc/Hindware

S & F shower arm 240mm long round shape with flage including fixing to steel pipe or union complete all as specified and directed. Make-Essco (ALE-CHR-536A) or equivalent from Marc/Hindware

S&F in repair PVC connection 15mm size with PTMT nut of length 450mm complete all as specified and directed.

S & F in repair for chromium plated Health faucet with 8mm Dia, 1.2 Meter long flexible tube and wall hook with N.R.V (Back Flow Preventer) complete all as specified and directed.

S&F Tublar Towel Rail 20mm dia, ‘D’ type 600mm long between Flanges Brass Chrommium Plated, complete all as specified and as directed.

S&F PVC bathroom cabinet box with mirror, shutter type of size 500X400 fixed on walls with wooden plugs and and chromium plated brass screw and cup washer as in repair complete all as specified & directed.

S&F Rotational Moulded Polyethylene (HDPE) Water Storage Tank 1000 Litre Capacity (Cylindrical Vertical with Closed Top), Black in Colour, Three Layered Construction, hoisted and fixed in Position all specified in MES Schedule Part-I and including ball valve high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for 25mm outer diameter for CPVC pipe, including provision of 25mm x 100mm GI nippples with check nuts for inlet, outlet wash and overflow pipe , complete all as specified and as directed.

M&L Cement Concrete type B-1, (1:2:4) using 20mm graded crushed stone aggregate in cills, steps; seismic and similar bands, plinth courses. string courses, lacing courses, copings, kneelers, apex stones, kerb and the like including weathering, slightly rounded or chamfered angles and throatings, as directed including use and waste form work (straight or curved) complete all as specified and as directed.

M&L for Concrete bed Type C-2 (1:3:6) (Using 40mm graded crushed stone aggregate) to 150mm dia drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested complete all as specified and directed

M&L for 150mm dia Reinforced concrete pipes, class NP-3, laid and jointed with collars complete all as specified and directed.

S&F work for single socketed UPVC (SWR) pipe Type "B" 110mm bore with rubber ring joint any radius complete all as specified and directed

M&L Plain Cement Concrete type 1:2:4 type B-0 (using 12.50mm graded stone aggregate as in surface channels and drains complete all as specified and as directed.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped end etc complete all as specified and as directed.

M&L for Point wiring with PVC insulated and unsheathed FRLSH cable single core multistranded copper conductor 1.5 sqmm size, 1100 volts grade cable conforming to IS - 694 1990 drawn through and including PVC concealed conduit 20mm dia medium duty with all accessories including fabricated 1.6 mm thick MS terminal boxes fixed flush with wall surface with 3 mm thick plastic masonite laminated sheet top cover fixed with cadmium screw for mounting switches, sockets, regulator etc including 1.5 sq mm FRLSH stranded PVC insulated and unsheathed copper conductor earth continuity conductor to common earth and connecting to earth dolly all as specified for one light or fan point controlled by one switch single pole one way for light/ ceiling fan/ exhaust fan/call bell point/ Switch socket outlet 5 amps complete all as specified and as directed. Note: (i) Red coloured cable shall be used for live connection, black coloured cable shall be used for neutral connection and green coloured cable shall be used for earthing. Separate cable for earthing and neutral to be used for each individual circuit from the distribution board.

All as per item No here-in-before but one 3 pin 5 amps socket outlet on the same board with other switch complete all as specified and directed by Engineer-in-charge.

All as per item No. here-in-before but one 3 pin 5 amps switch socket outlet on the independent board with other switch complete all as specified and directed by Engineer-in-charge.

M&L Point wiring with 2.5 sqmm (Nominal Area) PVC insulated stranded single core unsheathed FRLSH copper conductor cable 1100 Volts grade drawn through with and including PVC concealed conduit 20mm dia medium duty with all fittings and accessories of (like Tee, Bend etc) complete fixed to walls / ceiling etc with and including 2.5 Sqmm (nominal area) PVC insulated unsheathed, stranded, single core FRLSH copper cable as earth continuity wire connecting to common earth point (including supply & fixing of 1.6 mm thick pressed mild steel terminal boxes of suitable size with 3 mm thick PVC /plastic laminated sheet, top cover suitable sizes of brass screws and washers etc. for mounting sockets for 5 pin, 16 Amp socket outlet on independent board complete all as specified and directed. Note: (i) Red coloured cable shall be used for live connection, black coloured cable shall be used for neutral connection and green coloured cable shall be used for earthing. Separate cable for earthing and neutral to be used for each individual circuit from the distribution board.

S&F Switch piano, flush type, SP, one way, 5/6 Amps 230/240 Volts, white/ivory finish complete all as specified and directed.

S&F socket combination multipurpose 2 in 1, 5 pin 6 Amps 230/240 volt flush type complete all as specified and as directed.

S&F Socket outlet 3/5 pin, 6 Amps, 240 volt flush type complete all as specified and as directed.

S&F Switch socket combination multipurpose 2 in 1, 6 pin 15 Amps 230/240 volt flush type complete all as specified and as directed.

S&F Ceiling rose surface bakelite three terminals 240 volts complete all as specified and as directed.

S&F 9W LED bulb, 6500k, PF>0.9, CRI>80 lumen efficacy warmlight/ natural white alongwith PVC Lamp holder complete all as specified and directed by the Engr-in-Charge.

S&F Energy efficient LED fittings of capacity 1 x 10W suspended type / wall mounted type complete with LED tube Lamp and fitting with copper flexible PVC cable of 0.50 sq mm twin core not more than one metre in length complete all as specified and as directed.

S&F Energy efficient LED fittings of capacity 1 x 20W suspended type / wall mounted type complete with LED tube Lamp and fitting with copper flexible PVC cable of 0.50 sq mm twin core not more than one metre in length complete all as specified and as directed.

S&F building security light pressure die cast housing with individual LEDs with modular secondary optics security light luminaires 35 watt LED with 32mm dia light grade GI pipe bent to shape of 45'' 1.5 mtr long and nuts bolts including fixing arrangement complete all as specified and directed by Engineer-in-Charge.

S&F Sheet metal enclosure for DB's when MCBs to be used 4 way single pole and neutral double door with 200 amps rated bus bar complete 240 volts complete all as specified and as directed.

S&F Sheet metal enclosure for DB's when MCBs to be used 8 way single pole and neutral double door with 200 amps rated bus bar complete 240 volts complete all as specified and as directed.

S&F MCB 6 to 32 Amps, SP, 240 Volts , 'C' curve breaking capacity 10 kA complete all as specified and as directed.

S&F MCB 40 Amps, TP 240 Volts ,C- Curve breaking capacity 10 KA including necessary connection complete all as specified and as directed.

S&F MCB 63 Amps, DP 240 Volts ,C- Curve breaking capacity 10 KA including necessary connection complete all as specified and as directed.

M&L Sub main wiring with 2 runs of single core FRLSH type PVC insulated unsheathed stranded copper conductor of size 4.0 Sqmm and one run of PVC insulated unsheathed multistrand copper conductor FRLSH type of size 4.0 Sqmm as earth lead drawn into rigid non metalic PVC conduit of size 20 mm dia including all fittings complete all as specified and as directed. Note:- Two runs of 4 Sqmm conductor as main wire and one run of 4 Sqmm conductor as earth wire with one run of PVC conduit shall be measured as one unit.

Supplying and fixing new ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete with all the connection as directed.

Materials and labour Earthing complete with galvanised steel earth plate electrode 60 Cm x 60 Cm x 6.00 mm thick buried in ground (earth pit not less than 2.25 m deep below ground level) with top edge of the plate not less than 1.5 m below normal ground level, connected to GI wire 4 mm as earthing lead by means of bolts, nuts, check nuts and washers of GI or steel, GI strip projected by 40 mm bore light grade GI pipe and other end connected to earth test point as directed including funnel with watering pipe 20 mm bore light grade galvanised iron, wire mesh, charcoal or coke common salt laid in alternative layer of 15 cm (complete thickness) all round the earth electrode, concrete earth pit in PCC (1:3:6) type C-1, 50 mm thick pre-cast RCC (1:2:4) type B-1 normal mix cover slab reinforced with 8 mm dia TMT bar 10 Cm c/c both ways and single handle of 10 mm dia round bar including necessary excavation, earth work etc. in soft / loose soil and disposal pf soil to a distance n. exc. 50 m and necessary testing on completion all as shown in electrical plate No. 3 MES Schedule Part-I complete all as specified and as directed.

Supply and laying dry coarse sand as in cushioning of under ground electric cable in trenches, laid to a uniform thickness of 23 Cm (15 Cm under the cable & 8 Cm over the cable) and gently punned down to 18 Cm thickness complete all as specified and as directed by the Engr-in-Charge. Note:- Thickness after punning down shall be measured for payment.

Materials and Labour Cutting existing road / path etc for taking out cable and proction pipe and making good the disturbed surfaces with cement concrete type C2 ( 1:3:6,) using 40mm graded crushed stone aggregates) of suitable depth complete all as directed by Engineer-in-Charge.

M&L for 80mm bore GI tubes light grade for cable protection with all fixing accessoires (clamps, nut, bolt and washer etc) complete all as specified and directed.

Supply and laying in trenches Bricks, sub class 'B' over burnt (kiln burnt) old size bricks, laid flat dry with width of the bricks laid to the axis of the cable for protection of cable complete all as specified and as directed by the Engr-in-Charge.

Laying only in trenches Except Bricks, laid flat dry with width of the bricks laid to the axis of the cable for protection of cable complete all as specified and as directed by the Engr-in-Charge. Note:- Serviceable bricks shall be obtained from taking down item.

Supply and laying XLPE insulated PVC sheathed, armoured, aluminium conductor cable 1100 Volt grade 35 Sqmm 3.5 core in trenches/ duct/floor/wall with provision of saddle and lugs, joints etc including connection complete all as directed by the Engr-in-Charge.

Supply and Laying Steel Water Tubing 20mm Bore (dia), Galvanised, ‘Medium Grade’ with all Fittings, laid in trenches or any other Situation, complete as all specified and as directed.

Supply and Laying Steel Water Tubing 25mm Bore (dia), Galvanised, ‘Medium Grade’ with all Fittings, laid in trenches or any other Situation, complete as all specified and as directed.

M&L cutting drilling and tapinge existing CI/DI water mains in position for addn/altn of for taking branch connection/ insertion of pipe specials valve of 25 mm to 80 mm bore pipe complete all as directed be Engineer in charge

Supply and fix Gun metal, globe or gate valves (ISI marked) ( Class-I) with iron wheel head, screwed both ends for 25 mm bore GI pipe complete as specified and as directed

BHASKAR SUPPLY AGENCY (BID ID -3486030)

RADHA ENTERPRISE (BID ID -3485407)

INDIA ELECTRICAL EQUIPMENTS (BID ID -3486667)

MS AP CONSTRUTION AND CO (BID ID -3486431)

UNIVERSAL TRADING CENTRE (BID ID -3486065)

M/S Manna Construction (BID ID -3486195)

SK CONSTRUCTION SYNDICATE & ENGG CO (BID ID -3486429)