Construction of 1 no. Weigh bridge room for 150MT dumper weigh bridge at Dhoptala OCM under Sasti Sub Area.

Amount

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50m.All kinds of soil.

Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources: 6 graded stone aggregate 40 mm nominal size derived from natural sources).

Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centring, shuttering, finishing and reinforcement - All work upto plinth level.1:1.5:3 (1 cement: 1.5 coarse sand (zone-III) derived from natural sources: 3 graded stone aggregate 20 mm nominal size derived from natural sources).

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth: consolidating each deposited layer by ramming and watering, lead upto 50 m and lift upto 1.5 m.

Brickwork with FLY ASH bricks in foundation and plinth in C.M. 1:6 of approved quality as per the instructions of engg in charge

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1.5:3 (1 cement: 1.5 coarse sand (zone-III)derived from natural sources: 3 graded stone aggregate 20 mm nominal size derived from natural sources).

Brickwork with FLY ASH bricks in superstructure in C.M. 1:6 of approved quality as per the instructions of engg in charge

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts, etc. Upto floor five level excluding cost of centring, shuttering, finishing and reinforcement. 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources).

Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete.Thermo-Mechanically Treated bars.

Centring and shuttering including strutting, propping etc. and removal of form for :Foundations, footings, bases of columns etc. for mass concrete.

Centring and shuttering including strutting, propping etc. and removal of form for : Suspended floors, roofs, landings, balconies and access platforms

Centring and shuttering including strutting, propping etc. and removal of form for :Lintels, beams, plinth beams, girders, bressumers and cantilevers.

Centring and shuttering including strutting, propping etc. and removal of form for :Columns

12 mm cement plaster of mix :1:6 (1 cement : 6 fine sand )

6 mm cement plaster of mix :1:3 ( 1 cement : 3 fine sand )

Providing and laying Ceramic glazed floor tiles 300x300 mm (thickness to be specified by the manufacturer ) of 1st quality conforming to IS: 15622 ofapproved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick Cement Mortar 1:4 (1 Cement : 4 Coarse sand) including pointing the joints with white cement and matching pigment etc. complete.

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade:New work (two or more coats) over and including priming coat with cement primer.

Finishing walls with Acrylic Smooth exterior paint of required shade :New work ( Two or more coat applied @ 1.67 ltr/10sqm. over and including base coat of water proofing cement paint applied @ 2.20 kg/10 sqm.)

Painting with synthetic enamel paint of approved brand and manufacturer to give an even shade ( Two or more coats on new work )

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. all complete.Fixed to steel windows by welding

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.

Providing and fixing aluminium work for doors,windows,ventilators and partitions with extruded built up std tubular sections/ appropriate Z sections and other sectionsof approved make conforming IS: 733 and IS: 1285, fixingwith dash fasteners of required dia and size,including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc.Aluminium sections shall be smooth, rust free, straight,mitred and jointed mechanically wherever requiredincluding cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete asper architectural drawings and the directions of Engineer-incharge.(Glazing, paneling and dash fasteners to be paid forseparately) :For shutters of doors, windows & ventilator sincludingproviding and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost ofEPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Powder coated aluminium (minimum thickness of powder coating 50 micron

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):

Providing and fixing angle iron frames for doors, windows and ventilators of mild steel Angle sections of size 35x35x5 mm, joints mitred and welded by angle iron 35x35x5 mm or 35x 5 mm flat pieces to the existing T-iron frame or to the wall with dash fastener, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer, all complete as per the direction of Engineer-In-charge.

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: ( 30 mm th )

Providing and fixing ISI marked oxidised M.S. handles conforming to IS:4992 with necessary screws etc. complete : ( 125 mm )

Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete : ( 300 mm x 16 mm )

Providing and fixing ISi marked oxidised M.S. door latches conforming to IS:5930 with screws etc. complete : ( 300 x 20 x 6 )

Filling in foundation with boulder and moorum in the ratio of 70:30 including watering and compaction as per the instruction of engg in charge

Point wiring for light/fan/bell in 20 mm ISI marked HMS PVC conduit with 1.5 sq.mm (2+1E) FRLSH grade copper wire with flush type switch and required accessories as per specification No: WG-PW/SW

Wiring for plug on board with Switch socket, copper wiring and earthing as per specification No: WG-PW/SW ( 1.9.13 )

Point wiring for independent plug in 20 mm ISI marked HMS PVC conduit with 1.5 sq.mm (2+1E) FRLSH grade copper wire, flush type switch, earthing and required accessories as per specification No: WG-PW/SW ( 1.9.8 )

Supplying and erecting flush type shockproof plug socket 6A & 16A (6 pin) with 16A switch combined with indicator lamp and fuse with gang box on wooden board. ( 1.7.13 )

Supplying and erecting electronic type step regulator for ceiling fan 600/ 900/ 1200/ 1400 mm. sweep, complete erected on provided switch board. ( 2.13.19 )

Supplying & erecting mains with 2x2.5 sq.mm. and earth wire 1.5 sq.mm FRLSH PVC copper wire in HMS PVC conduit min. 20mm dia. as per specification No: WG-MA/PC.( 1.6.4 )

Supplying, erecting & marking SPN MCB 6A to 32A, B- series (for lighting) in provided distribution board as per specification no. SW- SWR/MCB ( 5.3.11 )

Supplying, erecting & marking FPMCB 40A to 63A in provided distribution board as per specification no. SW-SWR/MCB ( 5.3.17 )

Supplying & erecting LED 20W tube light fitting (4 feet) with aluminium housing, heat sink, integrated HF electronic driver complete.

Supplying and erecting five star rated energy saving Ceiling fan 230 V A.C. 50 cycles 1200 mm complete erected in position as per specification no. FG-FN/CF ( 2.12.21 )

Providing earthing with copper earth plate size 30 x 30 x 0.315 cm complete with all materials, testing & recording the results as per specification no. EA-EP ( 9.1.2 )

Supplying and erecting triple pole metal clad HRC fuse switch 415V, 63A with neutral link with HRC fuses on angle iron /GI frame as per specification no. SW-SWR/TPHRC. ( 5.1.15 )

Total impact of GST for the purpose of CTC

GREEN EARTH INFRA PROJECTS

SATPUTE CONSTRUCTION

D. K. Ojha

Omprakash Yadav