RESTORATION TO DIFFERENT TYPES OF CHAIRS INCLUDING CANNING, PAINTING AND POLISHING HELD FOR OFFICERS, PBOR AND OTM ACCN UNDER GE (EAST), MATHURA

Amount

Removal of following existing unserviceable cane/old broken components of furniture item carefully without disturbing the adjoining parts and Supply and fixing new components of teak wood in lieu of dismantled components including tightening the joints, pinning, screwing, nailing, wedging, glueing, placing every part in-tact, as applicable as per drgs. Note :- (a) For all items of BOQ viz 1.01 to 16.05 (b) Work shall be executed where the furniture exist in different User Units under AOR of GE (East) Mathura including BSO's Furniture Yard as directed by Engineer-in-Charge. CHAIR DINING ,FD-279,262,228,FD/MAP-II/05

Back rest all as per drawing.

Leg stiffener all as per drawing.

Front leg all as per drawing.

Rear Leg all as per drawing.

Rail all as per drawing.

Removing the existing unserviceable cane plastic from the chair dining,tightening the loose joints of each chairs by pinning,screwing, nailing, wedging and glueing,placing every part in-tact and recanning the chairs in true Godrej pattern with plastic cane 2mm to 2.5mm wide of white colour 1st quality.The border of seat shall weaved with 4mm thick cane.The canning of chairs shall only be carried out after complete polishing process as specified and as shown on drgs.

Removing the existing unserviceable/broken PVC seat from the chair and supply and fixing new PVC seat 4mm thick after providing sufficient corner support and one additional stiffener at centre for support of PVC seat.The PVC seat shall be fixed with proper screws and good workmanship.Due care shall be taken while fixing the PVC seat, the gaps if appears be filed with putty mixed with adhesive so as to make the upper surface smooth and tidy. The PVC seat shall got approved from GE before supply. MAKE OF PVC SEAT –AMKO/COMFO/HARMONY

M&L for preparation of wooden surfaces by scratching the entire wooden pallets of chair dining, filling putty to the bore holes making surface smooth by scratching it with sand emery paper, the chair shall be tighten, properly cleaned and smoothened before polish and applying french polish to high glossy finish complete all as specified and as directed by Engr-in-Charge.

Removal of following existing unserviceable cane/old broken components of furniture item carefully without disturbing the adjoining parts and Supply and fixing new components of teak wood in lieu of dismantled components including tightening the joints, pinning, screwing, nailing, wedging, glueing, placing every part in-tact, as applicable as per drgs. CHAIR EASY,FD-229, 358, 1108

Rear leg all as per drawing.

Front Leg all as per drawing.

Rail seat all as per drawing.

Stiffener all as per drawing.

Back rest all as per drawing.

Arm all as per drawing.

Removing the existing unserviceable cane plastic from the chair easy,tightening the loose joints of each chairs by pinning,screwing, nailing, wedging and glueing,placing every part in-tact and recanning the chairs in true Godrej pattern with plastic cane 2mm to 2.5mm wide of white colour 1st quality.The border of seat shall weaved with 4mm thick cane.The canning of chairs shall only be carried out after complete polishing process as specified and as shown on drgs.

M&L for prepartation of wooden surface by scratching the wooden surface, filling putty for the bore holes making surface smooth by scratching it with sand embery paper and applying french polish to high glossy finish complete all as specified and directed by Engr-in-Charge.

Removal of following existing unserviceable cane/old broken components of furniture item carefully without disturbing the adjoining parts and Supply and fixing new components in lieu of dismantled components including tightening the joints, pinning, screwing, nailing, wedging, glueing, placing every part in-tact, as applicable as per drgs. CHAIR WRITING,FD-261, 280, 250, 1107

Back rest all as per drawing.

Leg stiffener all as per drawing.

Front Leg all as per drawing.

Rear Leg all as per drawing.

Rail all as per drawing.

Arm all as per drawing.

Removing the existing unserviceable cane plastic from the chair writing,tightening the loose joints of each chairs by pinning,screwing, nailing, wedging and glueing,placing every part in-tact and recanning the chairs in true Godrej pattern with plastic cane 2mm to 2.5mm wide of white colour 1st quality.The border of seat shall weaved with 4mm thick cane.The canning of chairs shall only be carried out after complete polishing process as specified and as shown on drgs.

M&L for prepartation of wooden surface by scratching the wooden surface, filling putty for the bore holes making surface smooth by scratching it with sand embery paper and applying french polish to high glossy finish complete all as specified and directed by Engr-in-Charge.

Removal of following existing unserviceable cane/old broken components of furniture item carefully without disturbing the adjoining parts and Supply and fixing new components in lieu of dismantled components including tightening the joints, pinning, screwing, nailing, wedging, glueing, placing every part in-tact as applicable as per drgs. CHAIR VERANDAH:-FD-19M,256,359,259,FD/MAP-II/06

Spot gas welding to broken parts/joints of chairs.

Removing the existing unserviceable cane/niwar plastic from the chair verandah and recanning the chair with plastic cane 3.5mm to 4mm wide of 1st quality, white colour in pure godrej pattern The canning of chairs shall only be carried out after complete painting process as specified as specified in drg. MAKE OF CANE- SHAH,PREMIER Note:- Painting shall be measured & paid separetely under relevant item of this BOQ.

Removing the old broken shoes of chairs and Supply and Fixing best quality new PVC shoes to the legs of chair.

Removing the existing unserviceable/broken PVC seat and back from the chair,supply and fixing new PVC seat and back 4mm thick to the chair verandah MAP after providing flat iron 20mmx4mm support in centre of seat only by proper welding for support of PVC seat.The PVC seat shall got approved from GE before supply. MAKE OF PVC SEAT –AMKO/COMFO/HARMONY

M&L for painting the frame of the chairs by applying one coats of synthetic enamel white of approved quality paint after prepartion of steel surface by sanding with sand emery paper and dusting the surface with clean cloth.

Removal of following existing unserviceable old broken wooden/ply components of various furniture items or similar items carefully without disturbing the adjoining parts and Supply and fixing new components in lieu of dismantled components including tightening the joints, pinning, screwing, nailing, wedging, glueing, placing every part in-tact, as applicable as per drgs. CHAIR WOODEN BOTTOM W/O ARMS FD-56/225

Back rest all as per drawing.

Leg stiffener all as per drawing.

Front leg all as per drawing.

Rear Leg all as per drawing.

Rail all as per drawing.

Removing the existing unserviceable/broken seat of chair without disturbing the adjacent parts ,supply and fixing 6 mm thick commercial ply for seat of chair with standard workmanship.

M&L for prepartation of wooden surface by scratching the wooden surface, filling putty for the bore holes making surface smooth by scratching it with sand embery paper and applying french polish to high glossy finish complete all as specified and directed by Engr-in-Charge.

Removal of following existing unserviceable cane/old broken wooden/ply wood components of furniture item carefully without disturbing the adjoining parts and Supply and fixing new components in lieu of dismantled components including tightening the joints, pinning, screwing, nailing, wedging, glueing, placing every part in-tact and polishing/painting the disturbed portion, as applicable as per drgs. CHAIR DINING CUSHIONED FOR OFFRS, FD/E6/MAP/10

Back rest all as per drawing.

Teak wood vertical stiffener all as per drawing.

Front Leg all as per drawing.

Rear leg all as per drawing.

Stiffener all as per drawing.

"L" bracket 04 nos in each chair of size 75mmx75mm shall be fixed to rail and legs for making the chair more strudy and durable.

supply of seat made of 12mm thick BWR plywood over which 40 density cool foam 75mm thick shall be provided duly covered with best quality tapestry cloth not less than `200/- per metre as approved by BSO/GE.

M&L for prepartation of wooden surface by scratching the wooden surface, filling putty for the bore holes making surface smooth by scratching it with sand embery paper and applying french polish to high glossy finish "L" bracket size 75mmx75mm shall be fixed at right angle of legs and rails complete all as specified and directed by Engr-in-Charge.

Removal of following existing unserviceable old broken components of furniture item carefully without disturbing the adjoining parts and Supply and fixing new components of teak wood in lieu of dismantled components including tightening the joints, pinning, screwing, nailing, wedging, glueing, placing every part in-tact, as applicable as per drgs. CHAIR EASY CUSHIONED:- FD-358

Back rest all as per drawing.

Front Leg all as per drawing.

Rear leg all as per drawing.

Arm all as per drawing.

S&F in repair seat made of 12mm thick plywood over which 40 density cool foam, 75mm thick shall be provided duly covered with best quality tapestry cloth not less than `200/- per metre as shown on drg and fixed on top of side rails by screws. All as directed by BSO

S&F in repair back made of 12mm thick plywood over which 40 density cool foam, 75mm thick shall be provided duly covered with best quality tapestry cloth not less than `200/- per metre as shown on drg and fixed on top of back rails by screws. All as directed by BSO

M&L for prepartation of wooden surface by scratching the wooden surface, filling putty for the bore holes making surface smooth by scratching it with sand embery paper and applying french polish to high glossy finish complete all as specified and directed by Engr-in-Charge.

Removal of following existing unserviceable old broken components seat and back of furniture item carefully without disturbing the adjoining parts and Supply and fixing new components in lieu of dismantled components including tightening the joints, pinning, screwing, nailing, wedging, glueing, placing every part in-tact, as applicable as per drgs. CHAIR STEEL TUBULAR WITH ARMS : FD-75(M)

M&L for preparation of steel surfaces of chair and applying one coat of synthetic enamel olive green paint Complete all as specified and as directed by Engr-in-Charge

S&F 02 nos of MS flat of size 25mmx4mm welded beneath in between the width of the chair for support of seat alongwith supply and fixing new seat made of teak wood duly polished in natural shade including cane work in godrej pattern, fitting in position with 04 nos of nut bolts and washers of length 60-65mm.

Removing the old unserviceable back from the frame of the chair. Supply and fixing new back made of teak wood duly polished in natural shade including cane work in godrej pattern, fitting in position with 04 nos of nut bolts and washers of length 60-65mm

First class Hard wood teak Arm rest as per drg

Hard rubber shoes as per drg

Rubber cap for conduit pipe as per drg

Removal of following existing unserviceable old broken components of furniture item carefully without disturbing the adjoining parts and Supply and fixing new components in lieu of dismantled components including tightening the joints, pinning, screwing, nailing, wedging, glueing, placing every part in-tact, as applicable as per drgs. CHAIR STEEL TUBULAR WITHOUT ARMS : FD-75(M)

M&L for applying one coat of synthetic enamel olive green paint after preparation of steel surfaces. Complete all as specified and as directed by Engr-in-Charge

S&F 02 nos of MS flat of size 25mmx4mm welded beneath in between the width of the chair for support of seat. supply and fixing new seat made of teak wood duly polished in natural shade including cane work in godrej pattern, fitting in position with 04 nos of nut bolts and washers of length 60-65mm

Removing the old unserviceable back from the frame of the chair. Supply and fixing new back made of teak wood duly polished in natural shade including cane work in godrej pattern, fitting in position with 04 nos of nut bolts and washers of length 60-65mm

Hard rubber shoes as per drg

Rubber cap for conduit pipe as per drg

Removal of following existing unserviceable steel/cane/old broken wooden components of furniture item carefully without disturbing the adjoining parts and Supply and fixing new components in lieu of dismantled components, as applicable as per drgs. CHAIR CB STEEL PADDED WITH ARMS, FD-75(M)

M&L for applying one coat of synthetic enamel olive green colour after preparation of steel surfaces. Complete all as specified and as directed by Engr-in-Charge

S&F seat of the chair made out of 12mm plywood. The plywood shall be fixed over wooden frame made out of batten of size 40mmx20mm with nail and adhesive. The entire structure shall be covered with 100mm foam cushion and overwhich best quality tapestry cloth not less than ` 200/- per metre shall be fixed as directed by Engr-In –Charge. 02 nos of MS flat of size 25mmx4mm welded beneath in between the width of the chair for support of seat. The seat shall be fixed in between the frame with nut bolts and washers.

S&F back of the chair made out of 6mm plywood. The plywood shall be fixed over wooden frame made out of batten of size 40mmx20mm with nail and adhesive. The entire structure shall be covered with 50mm foam and over which best quality tapestry cloth not less than ` 200/- per metre shall be fixed as directed by Engr-In –Charge. The seat shall be fixed in between the frame with nut bolts and washers.

S&F in repair arm of the chair made out of 25mm thick teak wood in the shape of the arm.The arm shall be covered with 50mm foam and over which best quality tapestry cloth shall be fixed as directed by Engr-In –Charge. The arm shall be fixed over the conduit pipe and to be screwed from below.

Hard rubber shoes as per drg

Removal of following existing unserviceable components of furniture item carefully without disturbing the adjoining parts and Supply and fixing new components in lieu of dismantled components, as applicable as per drgs. CHAIR EASY STEEL, FD-121(M)

Continuous Gas welding as required per 10 CM.

Supply and fixing in repair new seat made of 12mm plywood over which 75 mm foam cushion shall be fixed with adhesive .The foam and plywood shall also be covered with best quality tapestry cloth as approved by BSO and GE irrespective of what is shown on drg. The complete seat shall also be tightening on seat frame with 08 screws.

First class Hard wood teak Arm rest as per drg

Supply and fixing in repair new back made of 12mm plywood over which 75 mm foam cushion shall be fixed with adhesive .The foam and plywood shall also be covered with best quality tapestry cloth not less than `200 per metre as approved by BSO and GE, irrespective of what is shown on drg. The complete back shall also be tightening on back frame with 04 screws.

Materials and labour for applying one coat of synthetic enamel black color on all steel portion of form including arm including preparation of steel surface complete all as specified and directed.

Shoes all as per drg

Removal of following existing unserviceable broken components of furniture item carefully without disturbing the adjoining parts and Supply and fixing new components in lieu of dismantled components, as applicable as per drgs. CHAIR WRITING, FD/E6/MAP/12

Removing unserviceable damaged Seat & back of Chair writing. Supply and fixing the seat&back made of 12 mm thick hot pressed plywood upholstered with fabric and moulded polyurethane foam with PVC lipping all round. The polyurethane foam shall be 50 mm thick and shall be moulded with density 50-55 Kg per cubic mtr on Hampden machine.

M&L for painting the entire frame with one coat of synthetic enamel paint 1st quality including preparation of surface of chair writing officers including handle all as directed by Engr -in -charge.

Removing old unserviceable arm rest of chair writing officer and S&F new arm made of black integral skin polyurethane with 75-85 shore 'Á ' hardness & reinforced with MS insert all as specified and directed by Engr -in -charge.

S&F in repair new Rubber stopper at bottom all as directed and specified by Engr -in -charge

Removal of following existing unserviceable broken components of furniture items or similar item, as applicable as per drgs. CHAIR COMPUTER, FD/E6/MAP/01

Removing unserviceable damaged Seat & back of Chair computer, supply and fixing new seat and back made of 12 mm thick hot pressed plywood upholstered with fabric not less than `200/- per metre and moulded polyurethane foam with PVC lipping all round. The polyurethane foam shall be 50 mm thick and shall be moulded with density 50-55 Kg per cubic Mtr on Hampden machine ,all as directed and specified by Engr -in -charge

Removing old unserviceable arm rest of chair computer and S&F new one made of black integral skin polyurethane with 75-85 shore 'Á ' hardness & reinforced with MS insert all as specified and directed by Engr -in –charge.

Removing unserviceable base along with castor twin wheels and S&F new base along with new castor twin wheel suitable for chair computer all as directed by Engr-in-charge.

Removing unserviceable adjustable tilting mechanism and S&F new adjustable tilting mechanism shall be forward tilt, self regulating tilt tension and manual override, 4 position tilt lock. Anti shock back mechanism to prevent backrest. 360 swivel mechanism to allow with fluid lateral movement suitable for chair computer all as specified and directed by Engr -in charge.

Removal of following existing unserviceable broken components of furniture item, as applicable as per drgs. CHAIR SCHOOL WITH HAND BOARD, FD/E6/MAP/05

M&L for applying one coat of synthetic enamel grey colour after preparation of steel surfaces. Complete all as specified and as directed by Engr-in-Charge,

S&F new One piece PVC seat and back and fixing the same by providing four screws as described in drg. Make of Seat-Blow plast/Nilkamal/supreme

S&F new 18mm thick prelaminated particle board top open able/hand board with 4mm thick teak wood edging and fixing the same by providing hinges/screws as described in drg

Hard rubber shoes as per drg

Removal of following existing unserviceable broken components of furniture item, as applicable as per drgs. CHAIR REVOLVING EXECUTIVE (LOW AND HIGH BACK)/CHAIR CONFERENCE TP & FD/E6/MAP/01

Removing of old fabric and pressed molded polyurethane foam cushion from seat and back of chair revolving executive after carefully removing the PVC lipping from the edges of the seat and back of the chair, Supply and fixing new moulded polyurethane foam cushion 50mm thick and fabric not less than `200/- per metre over the seat and back of the chair as per the existing shape of the chair duly providing new PVC lipping all-round the edges of seat and back of the chair.

Removing the old unserviceable arm of the chair revolving executive by unscrewing the bolt from the inner side, Supply and fixing new arm to the chair revolving executive of the same shape and size as of existing one. The arm shall be of black integral skin polyurethane reinforced with MS insert, it shall be scratch and weather resistant.

Removing the old unserviceable complete pedestal assembly (Complete Base) along with hydraulic system of chair revolving executive by removing the pin from bottom carefully without damaging the upper portion. Supply and fixing new pedestal assembly (complete base) along with hydraulic system of chair revolving executive with standard workmanship .The pedestal assembly shall consists of five wheel coasters for smooth running of chairs and shall have gas lift mechanism.

Removal of following existing unserviceable broken components of furniture item, as applicable as per drgs. CHAIR WRITING STEEL, FD-360

Continuous Gas welding as required per 10 CM.

Supply and fixing new seat made of 12mm plywood over which 100 mm foam cushion shall be fixed with adhesive .The foam and plywood shall also be covered with best quality tapestry cloth not less than ` 200/- per metre as approved by GE irrespective of what is shown on drg.The complete seat shall also be tighten on seat frame with 08 brass screws.

First class Hard wood teak Arm rest as per drg

Supply and fixing new back made of 12mm plywood over which 75 mm foam cushion shall be fixed with adhesive .The foam and plywood shall also be covered with best quality tapestry cloth not less than `200/- per metreas approved by BSO and GE, irrespective of what is shown on drg.The complete back shall also be tighten on back frame with 04 brass screws after removing the old unserviceable back.

Materials and labour of one coat of synthetic enamel black color on all steel portion of form including arms, complete all as specified and directed.

M&L for French polishing one coat to the following furniture articles all are of MES pattern or Similar items incl applying wax for depressed surface before polishing/painting all as specified and shown on drgs and directed by Engineer-in-Charge.Work will be executed where the furniture exist in Officers Married accn including OTM Accn and in different User Units under the jurisdiction of GE (E) Mathura including BSO's Furniture Yard as directed by Engineer-in-Charge.

FD-245,Bed Niwar with MNF Set but excluding to MNF Set same is measured and paid under item No. 18.01

FD-279,Chair dining

FD-229,Chair easy

FD-280,Chair writing

FD-233,Hat stand with mirror

FD-236,Peg Table

FD-281,Sofa set (4 seater cushioned)

FD-281,Sofa set (5 seater cushioned)

FD-282,Stool dressing

FD-248,Table bed side

FD-274,Table centre

FD-273,Table Dining 6 persons

FD-273,Table Dining 8 persons

FD-230,Table Dressing Gents

FD-378,Table Dressing ladies

FD-249,Table Writing

FD-264,Bed hard

FD-232,Teapoy

M&L for applying one coat of synthetic enamel paint to the following furniture articles including preparation of steel sruface all are of MES pattern or Similar items all as specified and shown on drgs and directed by Engineer-in-Charge. Work will be executed where the furniture exist in Officers Married accn including OTM Accn and in different User Units under the jurisdiction of GE (E) Mathura including BSO's Furniture Yard as directed by Engineer-in-Charge.

FD-245,Bed Niwar with MNF Set but only MNF Set

FD-1029, Locker Bed Side Steel

FD/E6/MAP/18, Almirah large steel

FD-1032,Almirah Steel medium

FD/E6/MAP/02(R),Rack shoe steel

FD-256,Chair Verandah

FD-255,Teapoy Verandah

FD/E6/MAP/15(R),Table bed side

Anand Construction

L.BHIMSEN

MISHRA CONSTRUCTIONS

ANUBHAV BUILDERS

ms Jyoti traders

Vinayak Distributors