Painting and Renovation of Koyambedu Wholesale Market Complex and Renovation of Market Management Committee office at Koyambedu Chennai 107

Amount

Dismantling and Clearing away the existing structure, conveying and dumping the debris etc., all complete as directed by departmental officers.

Brick / Stone Masonry in cement mortar walls under 3m high

Doors and Windows including removal of frames, hinges and fastenings

Floor finish and dadooing walls in cement mortar with Mosaic Tiles / Glazed Tiles / Cuddapah Slabs

Earth Work Excavation and deposting on banks with initial lead of 10m and initial lift of 2m in hard stiff clay stiff black cotton soil, hard red earth, shales, muram, gravel, stony earth and earth mixed with small boulders etc., as per SS 20B and as directed by departmental officers.

Supplying and Filling with Msand 100mm thick well watered rammed and consolidated complying with relevant standard specifications etc., all complete and as directed by the dept. officers.

Providing and Laying PCC 1:4:8 (1 of Cement, 4 of Sand and 8 of graded metal) using 40mm metal including cost and conveyance of all materials mixing, laying, compacting, curing etc., complete and as directed by the dept. officers.

Supplying and Erecting Centering for Sides and Soffits including necessary supports and strutting up to 3.29 M height for plane surface as detailed below in all floors with all cross bracings using Mild Steel sheets of size 90 x 60 cm and 10 BG stiffened with welded Mild Steel angle of size 25mm x 25mm x 3mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at about 90cm centre to centre and supported by casuarina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc., complete complying with the standard specification and as directed by the departmental officers.

For Plane surfaces such as RCC floor slab, roof slab, beams, lintels, bed blocks, landing slab, waist slab, Portico slabs and beams, etc.,

Reinforced Cement Concrete 1:1.5:3 (one of cement, one and half of sand and three of hard broken stone jelly) for all RCC works namely plinth beam, raft beam, slab, column, column footing and RCC walls using 20mm guage hard broken stone jelly excluding cost and facbrication of reinforcement grills, shuttering & centering but including vibrating, laying, curing and finishing etc., all complete and as directed by the departmental officers.

For Foundation and Basement

For Ground Floor up to 4.50 M height

For First Floor up to 4.50 M height

Supplying, fabricating and placing in position of MS/RTS Rods for grills for all RCC works including bending, tying grills and placeing in position including cost of steel, binding wire etc., complete and as directed by the departmental officer.

Brick Work in CM 1:5 [One of Cement and Five of M-Sand) 230mm thick Using 2nd class ground moulded chamber burnt stock of size 9"x4.5"x3" including dewatering wherever necessary proper setting, curing etc., all complete and as directed by the departmental officers.

Precast Solid Block masonry in C.M.1:5 (One of Cement and Five of Sand) using Solid block of size 40x20x20cm for super structure of the wall including cost and conveyance of all materials, proper settings, curing, scaffolding and labour charges etc., complete as directed by the departmental officers.

Plastering with C.M 1:3 (1 of Cement and 3 of M-Sand)12mm thick with fine river sand for plastering including curing, neat finishing, etc., complete complying with standard specification and as directed by the departmental officers.

Plastering with C.M 1:4 (1 of Cement and 4 of M-Sand) 12mm thick with fine river sand for plastering including curing, neat finishing, etc., complete complying with standard specification and as directed by the departmental officers.

Plastering with C.M 1:5 (1 of Cement and 5 of M-Sand) 12mm thick with fine river sand for plastering including curing, neat finishing, etc., complete complying with standard specification and as directed by the departmental officers.

Painting the walls with Two coats with first class quality Plastic Emulsion paint of approved colour over a priming coat including thorough scraping, clean removal of dirt. The rate includes cost of brushes, sand paper, plaster of parries, putty wherever required, neat finishing and scaffolding charges etc., complete complying with standard specification and as directed by the Departmental Officer (the colour and quality should be got approved by the Executive Engineer before use)

Weathering course-using Concrete broken brick jelly 20 mm gauge in pure slacked lime (No sand to be used) over RCC roof slab. The proportion of broken brick jelly to slaked lime being 32:12½ cft well beaten by wooden beaters for giving required slope and thickness required etc complete complying with standard specifications and as directed by Departmental Officers.

Finishing the top of roof with one course of machine pressed tiles of size 23x23x2cm of approved quality laid in CM 1:3 (one cement and three sand) mixed with 2% of water proofing compound by weight of cement used and pointed with the same oiled mortar including mixing of red oxide etc complete complying with standard specifications and as directed by Departmental Officers.

Supplying and Laying the Toilet Floor with Anti skid Vertified Tiles of approved quality, colour and design joint free of size 0.30 x 0.30m thick of approved quality and colour in all floor over a base layer of cement mortar 1:3 (1 of Cement and 3 of M-Sand) 20mm thick and laid strength alignment and pointed neatly with colour cement at the rate of 0.40Kg/sq.m laid without any air gap in the tiles neatly and fixing in position as per standard specification and as directed by the departmental officers. The colour and quality of tiles should be got approved by the Executive Engineer before use on work.

Dadooing the walls with Digital Wall Tile 0.45m x 0.30m best approved quality and colour in all shade of the glazed tiles in all floor over a base layer in Cement Mortar 1:2 (1 of Cement and 2 of M-Sand)10mm thick and laid in situ true alignment and pointed neatly with colour cement at the rate of 0.40Kg/Sq.m to suit the colour of the tiles fixed in position without any air gap in the tiles neatly etc., complete complying with standard specification and as directed by the the departmental officers. The Colour & quality of tiles should be got approved by the Executive Engineer before use on work.

Supplying and fixing jet black granite stone slab table rubbed, edges rounded and polished 18mm to 20 mm thick, as complete with all respects complying with relevant standard specification, as directed by the Engineer-in-charge.

Supplying and Fixing in position best quality approved make white glazed earthernware Oval Shape Wash Hand Basin of size 560 x 450mmwith a pair of cast iron brackets, including cost of 15mm dia metre brass chromium plated piller tap, 32mm dia metre G.M Wheel Valve, 15mm dia brass nipple 15mm dia nylon connection etc., including fixing the wash hand basin in the wall in position with pair of CI brackets with teak wood plugs and screws and giving necessary water supply connection and painting the brackets with two coats of paint over a priming coat of anticorrosive paint including testing for leakage etc., complete complying with standard specification. The quality and colour of wash hand basin and specials should be got approved by the Executive Engineer before use on work.

Supplying and fixing in position Indian Water Closet Oriya type of size 580x440mm white glazed earthen ware of approved quality with 'P' trap or 'S' trap conforming to IS:2556-part XII with sand cushion and forming flooring all-round the closet using 40mm broken brick jelly in lime concrete 1:2:5 (1 of lime, 2 of sand and 5 of brick jelly) 100mm thick and finishing the top to required slope and including giving necessary connection to cast iron soil pipes by dismantling brick masonry, reinforced cement concrete roof/ floor slab and making good the dismantled portion to original condition without leakage etc., complete complying with standard specification and as directed by the departmental officers. (The water closet should be got approved by the executive engineer before use on work.)

Supplying and fixing in position White / Colour Glazed Model Floor Mounted European Water Closet of best quality and approved make with 100mm “P” or “S” trap connecting with CI pipe of 100mm dia / PVC pipe of 110mm dia, double flapped rigid PVC black seat and seat cover with CP brass hinges including cost of white cement, cement for packing, spun yarn, teak wood plugs, brass screws, etc., including supplying and fixing 10 litres capacity PVC / 12.5 litres capacity porcelin low level flushing tank with a pair of CI brackets, etc., complete with all fittings, such as, 15mm brass ball valve with polythene float with brass handle, union coupling connected by means of 40mm white PVC flush hand using indian adopter joint including all internal fittings, such as, 15mm bras connections, 15mm GM wheel valve, 15mm brass nipple (2 Nos.), 15mm nylon connection, TW plugs, screws and also giving necessary connection to the PVC pipe and painting the CI brackets with 2 coats of approved paint over one coat of red oxide primer, dismantling the masonry and re-doing the dismantled masonry to original condition, etc., complete complying with standard specifications. (The EWC and flushing tank with all accessories should be got approved by the Executive Engineer before use on works) Floor Fitting

Supplying and Fixing in position best quality approved make of White glazed earthen ware lipped mouth Flat Back Urinal (Hindware-60002) with pressmatic tap - (Hindware-F310001) at 2 LPF of best approved quality with G.I.Pipe connection to suitable length,32mm bell mouthing P.V.C connection ,15mm dia pressmatic angle valve, fixing the urinal to the wall in position with necessary T.W.plugs ,clamps,screws, shellac etc., including dismantling masonry if necessary and redoing the same to original condition ,fixing the 15mm dia. G.I.pipe connection and gun metal wheel valve ,painting the pipe with two coats of approved color of synthetic paint over one coat of primer and etc.,checked without leakage etc., as complete with all respects complying with relevant standard specification, as directed by the Engineer-in-charge.

Solid PVC Door Shutters using 19 gauge 19mm MS square tubes for styles and outer frames.15mm MS square tubes for top, lock and bottom rails. The steel tubes shall be covered with 5mm thick solid PVC sheets. Shutter using 5mm thick solid PVC sheets for panelling shall rigitdly fixed in position including necessary furniture and fittings. The over all size of styiles shall be 50mm x 30mm. The over all size of top rail, Lock and bottom rail shall be 75mm x 30mm. The over all size of frames shall be 50mm x 45mm, with suitable rabate for housing the shutter.

Best Indian Teak Wood Panelled door in double shutters with frames 100x75mm at side,verticals and top. The shutters shall be of 40mm thick with moulded panels in 20mm thick planks,6Nos.of iron hold fasts fixed in c.c.1:2:4 6Nos.of butt hinges 125mm long including wind appliances, furniture,iron fittings,1No.of iron padlock 15cm long for locking arrangements and fixing inposition,etc.,complete.(ISI STD)

Removing the existing wooden partition and False ceiling The rate is inclusive of labour charges, materials etc., complete

Providing and fixing Wooden partition fully paneled partition made with aluminum tubular box section of 50 x 25 mm x 2400 mm fixed vertically at every 60cm interval c/c and with 3 horizontal member of same aluminium box section.The framework both sides will be fixed with 12mm thick BWR Plywood and finished with 1mm thick laminated of approved colour with suitable adhesive for the entire height.The rate inclusive of aluminium sections etc., complete

Single Person Workstation linear type of overall Size 1800 X 600 mm x 1200 H as per drawing and consisting of the following for each person: a) The work top shall be of 25 mm thick exterior grade prelaminated particle board cut as per shape and design as shown in drawing. The edge of the top shall be finished with 2mm thick PVC edge banding of matching colour of table top . Providing aluminium powder coated / anodised flip up box for wire management and key board tray. Top shall be supported with powder coated MS bracket of sufficient size and number. b) The partition shall be made of all aluminium frame finished with powder coating/anodized covered with combination of fabric and exterior grade laminated board. Each workstation to have one writing board and a pin up board. The thickness of partition shall be 65 mm and the height shall be of 1200 mm with level adjuster for main spin and return/divider with 37 mm.

Providing and fixing of 50mm rock wool of density 48 Kg/m3 of approved make shall be placed in the cavity glass wool rapped with 40GSM fibber glass tissue. The contractor must ensure that the rock wool is wire-braced to prevent it from ‘lumping down’ over a period of time. Rockwool holding clip should be used to hold Rockwool slab in its position.

Providing and fixing of 30mm thick Hard wood flush door and all around the door is fixed with 12mm thick teakwood lipping and finished with 1mm thick lamination of approved colour with suitable adhesive including 3 nos. of 125mm S.S.Hinges, handles and with necessary lock arrangements. The rate is inclusive of labour charges, materials etc., complete

Providing and fixing of 1mm thick laminate (Preferably wood / veneer grains) of approved colour and shade with grooves and lines and in patterns on specified area as instructed by Architect/Client . The cost of necessary hardware's, adhesives, wastages etc. as required for complete the works.

Supplying and Installing Metal False Ceiling using Fire Retardant Galvanized Steel Sheet Plain lay in tile size 600 mm x 600mm, 0.5mm thick, powder coated on external surface and shall have flange on all four sides to rest on the exposed grids. The system to give 600mm x 600mm centre to centre 'T'. The 'T' shall be not be dipped GI Tee Section 3600mm long main Tee. 24mm wide and cross Tee panels are formed by running main runner of 'T' section of size 30mm x 24mm powder coated at bottom at intervals with powder coating at bottom. Necessary provision of inter locking of 'T' section are made at required intervals not exceeding 1200mm. The main runners are suspended from the ceiling by means of 4mm dia. GI rods fixed to the ceiling using anchor fasteners of 50mm x 8mm size with nylon inset and hooked to the main rubbers using clips. The last hangers at end of each rubber should not be greater than 600mm from the adjacent wall. The last panel shall be placed at the side wall using edge profile 'L' Angle of size 20mm x 20mm and fixed to the side wall the false ceiling should be fixed of same level and should present a neat look

ALUMINIUM FIXED WINDOW OF SIZE 1.5M X 0.80M (Arch Type) Suplly & fixing of Ano. Alu. Fixed window with three panels using 62x38x2 mm @ 1.174 kg/m thick extruded box section as verticals and horizontal member and fixing 4 mm thick plain / frosted/ pin headed glass approved quality with necessary glazing clips, rubber beading etc., complete. Necessary dismantling making holes in RCC columns, beams, masonry wherever necessary with power drill to the extent required and made good to the original conditions after fixing as directed by the Board officers.The Al.Surfaces is to be anodised with matt finish usder electrically condition in accordance with ISI1868/1962 specification for an average anodic film thick of not less than 15 microns. (All materials should be got approved by the Dept. Engineer before fixing in position

ALUMINIUM THREE TRACK WINDOW SIZE 1.50 M X 1.20 M Supplying and fabrication and fixing in position of anodised natural colour matt finish sliding window in three track in all floors of size (Frame : Bottom Track with Gutter - 92 x 38mm @ 1.742 Kg/m, Side and top - 92 x 31.5mm @ 0.981 Kg/m, Shutter: Bottom, Top and plain side vertical -40x18mm @ 0.38 Kg/m, Interlocking vertical - 40 x 18mm @ 0.632 Kg/m). All the three shutters with sliding arrangements, the bottom section should have Gutter arrangements so as to drain the water entering and made with extruded aluminium section for outer frames with necessary accessories such rubber beading. Aluminium clips, rubber beading,handle and fixing 4mm thick clear sheet glass including all required for fabrication etc., complete.(Continues....)

Fixed Louver: Providing and fixing Storm proof Louver - Louver - 75 x 28 x 1.5 mm thick section no 2089 - weight not less than 0.464 Kg/Rmt "Z" type or Aerofoil - 75 made out of specially extruded aluminium with with anodizing with coating of approved colour and to be fixed with pitch not less than 50 mm and overlapping shall be 25 mm as minimum as shown in the drawing. Rate shall include supply and fixing of Louver, but excluding cost frames, plates, L - angle and other accessories, which shall part of Item above.

UPVC Ventilator Specification: Supplying and fixing UPVC (Un Plasticized Polyvinyl Chloride) Louvered Ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with GI/1mm 125GSM and 100% corrosion free, the profile are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with all over the edges of frame and shutter. The corners and joints should be welded and cleaned. Radiations pin headed glass 4mm thick should be provided in the louvers. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The ventilator should be got approved from the Executive Engineer before use on work

Supplying and Fixing in position special type of mirror of size 1000x780mm of approved quality and brand of approved colour with brass screw, rowel plugs etc., complete complying with standard specification and as directed by the departmental officers.

Supplying and Fixing in position PVC Nahani/Floor Trap with PVC Grating type of size 100 X 75 mm with best quality gratings of approved brand fixed over a bed of brick jelly lime concrete 1:2:5 ,(One of Lime, Two of Sand and Five of Aggregate) brick jelly 40mm and finishing with CM 1:3 (One of Cement and Three of Sand) including dismantling masonry wherever found necessary and making good to the original condition and giving connection to the gully trapes etc., all complete complying with standard Specification and as directed by the Departmental Officers.

Supplying and Fixing in position 15mm dia Brass Chromium Plated Screw down tap (Heavy Type) of approved make conforming to IS specification and quality including cost of shellac, thread, cutting and threading wherever necessary etc.,all complete complying with standard specification and as directed by the departmental officers.( Taps should be got approved by the Executive Engineer before use on the works)

Supplying and fixing of Soil line PVC Pipe 6 Kg /sqcm , of approved quality with necessary C.I. Gratings 110 mm dia PVC plain bend ,110 mm PVC shoe ,off sets,M.S. special clamps (heavy) teak wood plugs and screws of approved quality etc. including fixing C.I. grating 100mm dia at the junction of parapet and floor or roof slab and jointing with rubber lubricant etc, complete complying with relevant standard specifications and as directed by the departmental officers.

110mm Dia

75mm Dia

Supplying,laying and jointing UPVC Pipes of approved quality and best variety conforming to ISS with ISI mark, of the following Sizes above Ground level upto 4M height laid properly to alignment including cutting, threading and fixing the required PVC specials but excluding the cost of such specials and fixing to the wall with necessary TW Plugs, Clamps and screws, making holes on the wall or drilling holes in the roof and making good dismantled portion to original condition with necessary brick work, concrete and plastering wherever necessary with necessary scaffolding charges etc., complete and as directed by the departmental officers.

32mm dia pipe

25mm dia pipe

Supplying & Fixing of MS Grill including cost of materials, cutting, welding and fixing Charges etc., all complete and as directed by the departmental officers.

Painting the New Iron Work with Two Coats of best approved first quality and colour of Synthetic Enamel Paint over the existing Red Oxide Primer of approved quality and shade.The paint should be supplied by the contractor at his own cost, etc., all Complete and as directed by the departmental officers. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)

Painting the Old Iron Work two coat with synthetic enamel paint of approved quality and colour including ordinary scraping using brushes and neat finishing, etc., complete complying with standard specification and as directed by the Dept. Officers.(the colour and quality should be got approved by the Executive Engineer before use)

Providing Cup-board Shutter with frame using termite / water proof plywood of 19mm thick over which laminated sheet of 0.8mm thick fixed inside the shutter and 1mm thick fixed in top finishing of 18mm to 20mm thick jet black granite polyshed stone edge double nosing the outside of the shutter using fevicol along with necessary furniture fittings, such as, hydralic hinges, tower bolt,handles, multi purpose locks etc., as directed by the Departmental Officers. The design pattern, water proof plywood, laminate sheet and other materials should be got approved from the Executive Engineer befoe use on work.

Removing of Existing Mild steel hand rails etc.,

Manufacturing, Supplying and Fixing of Stainless Steel Hand rails for staircase using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick at required locations to a height of 900mm from finished floor level welded to 38mm dia Stainless Steel pipe post of 1.00mm thick as vertical at 900mm centre with 2 Nos. of 25mm dia intermediate horizontal stainless steel pipe of 1.60mm thick in between. The vertical pipe has to be welded to the 100 X 100 X 6mm MS base plate encased in the base concrete. The rate is inclusive of the charges for cutting, bending, welding, grinding, polishing, conveyance, electrical charges, etc. complete

Buy back of the removed Mild steel Pipe and disposing the same

Buy back of the removed novapan double skin partition, Aluminium partition and disposing the same.

Buy back of the removed gypsum board false ceiling and disposing the same.

Supplying and fixing Rajasthan Kota stones 20mm thick of size 60cm x60cm (Mechine edge finishing fully polished)over the existing base course including fixing the slab in cm 1:3, etc complete.

Providing dadoing with machine cut and machine high pre-polished best quality approved Granite stone slab of thickness not less than 20mm of size to the required size, set in C.M 1:3 ( 1 of cement : 3 of sand ), thickness not less than 15 mm including pointing with matching colour of Latapoxy SP100 and nosing the exposed edges as directed etc complete in all respects.

Supply and Laying of Chequered plate 6mm thick over cable trench including cost of materials and labour charges etc.,

Supplying and Erecting Pull and Push Type Rolling Shutter with ISI make of approved size and section using 18 GI sheet. The shutter shall be painted with one coat of red oxide primer and the rate is inclusive of hood covers, transportation charges etc

UPVC Window Specification: Supplying and fixing UPVC (Un Plasticized Polyvinyl Chloride) Windows of casement type (open) from the profile the size of outer frame 60mm x 58mm and shutter profile are reinforcement with GI/1mm 125GSM and 100% corrosion free, the profiles are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with over all the edges of frame and shutter the shutter will be provided with Espag multi power point locks and also it operates as handle. The corners and joints should be welded and cleaned. Radiations free pin headed plain or brown colour glass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and should have key lockable action, security protective hinges, strong locking systems and as per size for arresting noise and energy loss. The connecting mechanism between sash and outer frame that enables opening of the window. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The window should be got approved from the Executive Engineer before use on work

Manufacturing, Supplying and Fixing of Stainless Steel Hand rails for staircase using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick at required locations to a height of 900mm from finished floor level welded to 38mm dia Stainless Steel pipe post of 1.00mm thick as vertical at 900mm centre with 2 Nos. of 25mm dia intermediate horizontal stainless steel pipe of 1.60mm thick in between. The vertical pipe has to be welded to the 100 X 100 X 6mm MS base plate encased in the base concrete. The rate is inclusive of the charges for cutting, bending, welding, grinding, polishing, conveyance, electrical charges, etc. complete

Supplying and fixing in position of best quality of earthenware porcelain sink of size 600x 450x 200mm thick including the cost of 32 mm dia PVC waste 15 mm dia brass Nipple plug with chain and testing for leakage etc., complete complying with standard specification and as directed by the Departmental officers. The quality of sink and specials should be got approved by the Executive Engineer before use on work.

Supplying and installing Water treatment plant 2000LPH

supplying and fixing of Hydraulic Door closer of various sizes of approved quality using Aluminium Extruded section body tubular type universal hydraulic door closer with double speed.etc..,all complete as directed by the departmental officers.

Supplying and fixing of Aluminium door stopper with rubber bush with required screws etc..,all complete as directed by the departmental officers.

Supplying and fixing of Wallpaper of approved design over the finished surface of plywood after thorough scrapping of surface and levelling the surface pasted with Suitable adhesive. The rate is inclusive of labour charges, Materials etc., complete.

Supplying and installation of Effective optimized System Roller blinds of approved make consists of sanitized treated, resilient and colour fast blackout seclusion / Twill fabric 100% polyester, fabric width-200/250cm, fabric weight-270-295 g/cm2, thickness -0.50mm, colour fastness >5-6, Rubbing fastness -depending on color, shrinkage(%)wrap < 0.5%,weft : <0.5% & finished with blackout seclusion fabric of approved white base, reverse and front side pigment color coated with high tear strength, roller tube, control chain, control set left hand,control set right hand, bracket cover, chain connector, O-C bottom rail string for conversion spring, bottom end plug, bottom end plug circular, open bottom rail, tube bearing plug etc. complete

Supply of 2000 ltrs Pvc Sintex water tank including cost of materials , conveyance and fixing charges etc.,

Providing and grouting with single component Polyurethane Foam injection grout at dripping leakage locations, grout mixed at ratio of 10:1 (10 parts of Resin: 1 part accelerator) at the rate of 0.40kg/nozzle which will foam after reaction with water/ moisture, cream time <20 seconds, rise time <30 seconds, foam expansion more than 30 times. It has a mixed viscosity of <350 cP as per ASTM D 2196. Allow the PU foam grout to cure for 5 -10 mins. Providing and grouting with two component Polyurethane based resin injectiongrout mixed at ratio of 2:1 (2 parts of Base: 1 part Hardener) which will injected through same nozzleat the rate of 0.30kg/nozzel which gives Adhesion strength >2.5 MPa, Adhesion in wet concrete >1.5MPa, Elongation >80%. It has a mixed viscosity of <350 cP as per ASTM D 2196. The finished cost to include surface preparation, fixing of non-return valve injection packers at dripping leakage locations and damp patch locations, seal the nozzles with polyester resin anchor grout Instant leak plug 0.2kg/nozzle. All the application procedure shall be as per the direction of the Engineer In charge

Boring Providing and installing cast in situ single Under reamed piles of 300mm diameter having suitable size of Single bulb spaced at the interval as per norms , and length below pile cap in M-25 cement concrete , to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring with bentonite solution and the length of the pile to be embedded in pile cap etc., all complete.(Length of pile for payment shall be measured upto to the bottom of file cap) (Minimum Cement Content 400 Kg/Cu.m)

Supplying and fixing 3M MS steel Ladder inculding cost of material and cost of labour

Supplying and fixing single leaf flush door 32/30mm thickness both side commercial ply and approved brand with T.W.frames of size 100x75mm at side verticals and top, 6Nos.of iron hold fast fixed in C.C.1:2:4 and 3Nos.of butt hinges 125mm long including wind appliances furniture iron fittings 2Nos.of iron pad lock 15cm long for locking arrangements and fixed in position as directed during execution.

Dadooing Ceramic Tile 300mm x 450mm x8mm best approved quality and colour in all shade of the glazed tiles in all floor over a base layer in Cement Mortar 1:2 (1 of Cement and 2 of Sand)10mm thick and laid in situ true alignment and pointed neatly with colour cement suit the colour of the tiles fixed in position without any air gap in the tiles neatly etc., complete complying with standard specification and as directed by the the departmental officers. The Colour & quality of tiles should be got approved by the Executive Engineer before use in work.

Supplying of Fixing Fibre Reinforced Concrete (SFRC) Manhole Cover of 75 cm x 75 cm etc, including cost of materials and transportation charges etc.,all complete as directed by the departmental officers.

Supply and fixing of 300 mm (12") sweep (Light duty) AC exhaust fan complete with louvers shutters arrangements and necessary wall opening and making good of the wall

Supplying and fixing of PVC type 40 mm dia Angle cock with hose in urinal basin etc., complete complying with standard specification and as directed by the departmental officers.

Supplying and fixing of PVC type 20mm dia gate valve etc., complete complying with standard specification and as directed by the departmental officers.

Supplying and fixing of Cast iron grating size 100 mm x 75 mm etc., complete complying with standard specification and as directed by the departmental officers.

Flooring with red oxide cement plaster, polished surface and thread lining curing,etc.,complete as directed during execution.

Suppling and laying of first quality Best Mangalore Tiles for sloped roofs ( as per approved pattern showing the drawing not less than 18 mm thickness ) on roofs jointed with proper adhesive materials / 1:3 lime cement mortor for laying the tiles etc., The rate including cost of all materials, labour charges, wastages, necessary lead and lifts, transportation charges, loading, unloading, with all respects complying with relevant standard specification and as directed by the Engineer-in-charge.

Electrical Work

Supply, Erection, Testing, Commissioning and Handing over of 1No 8 Persons Passenger Lift Machine Room Less (MRL) as per the following specifications. Technical Specifications: 1) No. of Lift : One No. 2) Type of Lift : Passenger Lift 3) Capacity of lift: 8 persons (544 Kgs) 4) Speed : 1.5 mtr/sec 5)Type of Drive:Microprocessor based controllerV3Fdrive. 6) No. of floor: Ground + 2 floor 7) Total Travel: 15.00 mtrs (approx) 8) Leveling Accuracy: High level accuracy with smooth & jerk free stopping 9) Fire rated doors and ARD. 10) Construction of car: Stainless steel hairline finish with direct lighting with new beautiful single tube false ceiling with tubular handrail, 300mm sweep fan and mirror on back side for better aesthetic. 11) Position of Machine :Directly above the Lift level 12) No. of Landing Entrance – One in front 3 Nos (G+2) 13) No of Car Entrance: One in front only. 14) Car Entrance Door:- Stainless steel centre opening auto door. 15) Landing Entrance Door:- V3F Drive side opening sliding 18SWG stainless steel (Hairline finish) door with provision for emergency key opening at all landing.

16)Carsize : suitable car size (1300 mm x 1100 mm) 17)Car Clear Opening: 800mmx2000mm 18) Lift Well size : 2100mm wide x 2100mm deep 19) Lift pit depth:-1600mm 20) Power supply: 400/440 V Three phase 50Cy/Sec A.C.supply and 230V 50 Hz single phase AC supply for light. 21)Control: Micro computer based Duplex ull collective control with/without attendant. 22)Car fittings: Compact fluorescent/LED lighting with 2Nos 300mm sweep fans. 23) Lift Well: RCC Construction with brick masonry. 24)Lift Machine room available: 2100mm (width) x 2100mm (depth)as per IS 14665 (Part-5)-2000 25) Indication: Up/ Down Digital direction and position indicator for all landing and in car. 26)Emergency alarm bell:-Battery operated alarm bell to be provided with automatic charging device. 27)Emergency light : Battery operated light to be provided with automatic charging device. 28)Fire man’s switch : To be provided at Ground Floor 29)Minor builders work: To be provided by Lift Contractor. 30)Scaffolding : To be provide by contractor 31) Stainless steel sill angles and facia plates.

32) Steel for lift Machinery : To be provided by lift contractor 33)Servicing and Maintenance : Free comprehensive servicing and maintenance should be provided by lift contractor during the guarantee period of one year. 34)Automatic Rescue Device: To facilitate the landing of the lift to the nearest floor at the time of power failure. 35)Provision of Intercom with Phone: To be provided by lift contractor. 36)Lift license : Preparation of drawing payment of charges to CEIG and Insurance policies and obtaining CEIG safety certificate as per lift act should be done by lift contractor 37)Floor annunciator with music 38) Special Features. a) Voltage stabilizer for circuit control. b) Stainless steel signal fixtures. c) Vandal proof S.S. button with S.S. cover d) Stainless steel door frames for landing doors e) VF door operator f) Call register signal g) Stainless steel facia plate for car operating panel and landing fixtures h) ON-OFF switch for fan & light i) Pit Ladder

39) Over speed governor, phase failure and phase reversal relay, alarm bell, T guide brackets for car and counter weight. Rubber padding under winding unit. Motor of adequate capacity, single reduction worm gear, electromagnetic brake with compression springs, car safety gears, buffers, electro mechanical door locks. Emergency key. Side supporting angles motor over load protection devices, final limit switch main suspensions ropes, counter weights, lifting joint joist mounting the machineries. 40) Guarantee: Guarantee for the materials and workman ship of equipments complete should be offered by the Lift firm for a period of not less than one year. 41)Site testing in accordance with IS 14665 should be carried out at the time of handing over. 42) Providing Architraves by supply and fixing for all landing door entrances. (Make : Johnson, OTIS or Equivalent )

Supply and fixing of 32A FP MCB and 40A ELCB in suitable sheet steel enclosures in flush with wall with earth connection and inter connections(Legrand MDS)

Wiring with 2x1.5sqmm (22/0.3) PVC insulated unsheathed SC Cu. Conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessoires with modular metal flush switch box and 6A F.T. Modular switch with front cover plate in flush with wall making good of the concealed portion with suitable colour for PVC concealed modular light point / fan point (For electronic regulator) (Modular metal flush box,Modular switch, Cover plates should be legrand mosaic/ MK India-Blenze) (5 pt /coil)

Supply and fixing of WT bulk head fitting with guard (Philips / Bajaj / Crompton / K. Lite) suitable for11W CFL lamp with CFL. (Rate as per Data-4)

Supply and fixing of 5A (3 pin and 2 pin) combined flush type wall socket with control 5A switch concealed in suitable MS Box covered with Hylem sheet in flush with wall with earth connection (for lift room)

Supply and Fixing of 8 way single pole and neutral MCB sheet steel enclosure Distribution board with IP 42 protection metal Double door type with 1 No 10Amps DP MCB and 10A DP ELCB,10kA as incoming and 4 No's SPMCB,10kA as outgoing on angle iron frame with earth connection. The MCB DB, MCB's should be with the ISI mark (like Iegrand/Hager Make)

Supply and clamping of 3 1/2C x 25 sq.mm PVC LTUG armoured LTUG cable on post or on wall with MS Clamps.

Supply and fixing of brass cable gland for 31/2C x 25 sq.mm PVC armoured LTUG cable with earth connection

Supply and providing cable end termination of 3 1/2C x 25 sqmm PVC LTUG Aluminium armoured cable with necessary aluminium cable sockets by crimping etc. with electrical connection complete.

Earthing as per the ISI specification with an earth electrode of 2.1mt class 'B' GI pipe of dia not less than 40mm, with copper earth plate of size 125mm x 50mm x 6mm, with necessary funneling arrangements with necessary masonry work and with 38mm RCC cover slab for the brick masonry.

Supply and run of 1 No:8 SWG GI wire for earth connection

Supply, fabrication, of Copper earth flat of following size in provided trench, clamping in wall, ceiling, with suitable Clamps/ saddles, connecting the joints through bracing / welding covering with termination in the earth pits, Panels, Distribution boards and equipments with bitumen paint including accessories wooden plugs, screws, fastener etc., all inclusive

Supply and run of 2 of 2.5 sqmm (36/0.3)PVC insulated SC unsheathed Cu.Conductor of 1100V Grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 14SWG TC wire and making good of the concealed portion with suitable colour.

Supply and filling of R-22 Refrigerant Gas (Existing Split AC Units )

Dismantling, servicing and refixing of existing AC units

LIGHTING and ACCESSORIES:

Wiring with 2x1.5sqmm (22/0.3) PVC insulated unsheathed SC Cu. Conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessoires with modular metal flush switch box and 6A F.T. Modular switch with front cover plate in flush with wall making good of the concealed portion with suitable colour for PVC concealed modular light point / fan point (For electronic regulator) (Modular metal flush box,Modular switch, Cover plates should be legrand mosaic/ MK India-Blenze) (5 pt /coil)

Wiring with 2x1.5 sqmm (22/0.3) PVC insulated SC unsheathed Cu.Conductor of 1100V grade in suitable PVC rigid pipe clamping on wall and ceiling with PVC accessoires, Modular 6 module white plate with MS modular switch box with 6A modular switch suitable for light/ Fan Point (For electronic regulator)(Modular metal flush box,Modular switch, Cover plates should be legrand mosaic/ MK India-Blenze) (5 points per coil)

Wiring with 2x1.5 sqmm (22/0.3) PVC insulated SC unsheathed Cu. Conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories in flush with wall with MS Modular Junction and modular switch box and 6A modular FT switch (Crabtree / Legrand / Hager / Equivalent) with modular front plate in flush with wall and making good of the concealed portion with suitable colour for PVC concealed light/fan point (6 Points Per Coil) (For Rooms like Bath, Toilet,& Pump room etc..)

Wiring with 3 x 1.5sqmm (22/0.3) PVC insulated SC unsheathed Cu. Conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories in flush with wall with MS Modular Junction and modular switch box and 6A modular FT switch (Crabtree / Legrand / Hager / Equivalent) with modular front plate (Two way) in flush with wall and making good of the concealed portion with suitable colour for PVC concealed staircase light point.

Supply and fixing of single box type 4'20 W LED fitting with LED ( Philips / Crompton / Havells ) with TW round blocks on wall or ceiling with flu tube with PVC unsheathed Copper leads from terminals to the fitting.

Supply and fixing of 2'x2' 56W LED Square type Fitting (ORBIT ORPL-56W/Equivalent) complete with metallic chain suspension with PVC unsheathed copper leads from terminals to the fittings

Supply and fixing of 400mm HS wall fan (Havels make) complete on wall with necessary conditions.

Supply and fixing of 300 mm (12") sweep (heavy duty) AC exhaust fan complete with necessary wall opening and making good of the wall..

Supply and fixing of louvers shutters arrangements for 300 mm (12") sweep light duty AC Exhaust fan

Supply and fixing of 1200mm (48") sweep AC ceiling fan 5 star rated complete ( Higher end) with 2 module 100W fan step regulator (Higher end) with 2.5 metre down rod with fan clamp, and wiring to the near by point with 1.5 sqmm FRLS, PVC insulated copper wires, including necessary accessories and hardware's as required.

Supply and fixing of 1 No. 6A 5pin wall socket with 6A FT control switch (Crabtree / Legrand / Hager / Equivalent) in suitable MS modular Box covered with Modular 3module white plate in wall with earth connection

Supply and fixing 2Nos 6A modular (2 in one 3pin socket) wall socket with control switches and 1 No. 6A/16A 3pin switched socket(16A Switch and Socket combined) with suitable MS modular box covered with Modular 9 module white plate on wall with earth connection(For computer plug socket)

Supply and fixing of 1 No. 6A/16A 3pin switched socket(16A Switch and Socket combined) with control switch (Crabtree / Legrand / Hager / Equivalent) in suitable MS modular Box covered with Modular 3module white plate in wall with earth connection.

Supply and erection of 6mtr High GI Steel Tubular Single Arm Bracket Pole with bottom of 3.65mm thick HT sheet steel plate along with 250 x 250 x 6mm base plate and 2mtr Single long arm bracket. The above Pole size of 76.10mm OD x 3.65mm Thick x 6000mm Length. Suitable for mounting 1no of 120W LED street light fittings. Including base plate and concrete foundation with M24 x 750mm long J type foundation bolts (EN8 grade) as shown in the drawing. The pole should be provided with 6A Single pole MCB housed in weather proof box DP 6A MCB, 4 way 30A rated terminal block for loop in and loop out cable arrangements, SMC box for loop in loop out, including earth with 1mtr long 25mm dia B’ class G.I pipe as earth electrode with charcoal, salt with 10SWG G.I. wire interconnected with street light pole. Cable entry and exit in G.I. pipe of 2.5” dia. fitted in pole with clamps as per DRG and Technical specification.

Supply and fixing of 30W LED street light fitting with heat resistant toughened glass with IP 65 Prtection in suitable dia GI pipe (Class 'B') complete on the existing post or wall with PVC unsheathed Copper leads MS clarnps and aluminium painting (Philips/Havels/equivalent)

Supply and fixing of LED Bollard light Post fitting of 10W - 2 Mtr Ht. with pressure die cast aluminium housing body for optimal thermal dissipation. Lamp compartment comprising of anti glare clear diffuser with Injection moulded polycarbonate / clear glass material, delivering superior light output Rated life Burning Hrs 50000 hr @ Lumen Maintenance of 70%, CCT > 5500K, IP 66 optical and electrical compartment & impact resistance of complete luminaire > IK08. Power Factor >0.9 with mains, Surge Protection- Min 5KV along with Over voltage / Overload, short circuit / miss-wiring protection. Universal Voltage driver to operate wide voltage range from 100V to 270V 50/60Hz application. Compliance to IS 10322/IEC 60598, LM 79 & LM 80 Adherence with RoHS. UL approved MCPCB, with 2 years Warranty against any manufacturing defect working under standard electrical condition

Supply and Fixing of 8 way single pole and neutral MCB sheet steel enclosure Distribution board with IP 42 protection Double Acrylic door type with 1 No 32Amps DP MCB and 6 No's 6A to 10A SPMCB,10kA as outgoing on angle iron frame with earth connection. The MCB DB, MCB's should be with the ISI mark(like Iegrand/Hager Make)

(Switches for Existing PDB) Supply and fixing of 12 No. 63A FP MCB as incoming and 72 Nos.32A SP MCB as outgoing with necessary connectors earth links etc., for the existing Power DB (Like Legrand/Hager make)

63A FP MCB

32A SP MCB

Supply and installation of 8Way Vertical distribution Board with 40amps FP MCB as incomer and 8 nos 6A to 32A TP MCB as outgoing along with necessary interconnections, nuetral links and earth link. The rate includes necessary cutting charges for labour etc.complete

VERTICAL THREE PHASE MCCB DISTRIBUTION BOARD WITH MCCB's : Supply and fixing of 4 way Vertical Type sheet steel FP MCCB DB + 12 Modules with IP43 Protection as per IS 8623 III, Impact resistance IK09 of surface type fitted with bus bars and neutral links with 1 No. of 160A 4 Pole MCCB as Incoming, 2 Nos.of 100A, Triple Pole MCCB and 2 Nos.of 63A, Triple Pole MCCB for Outgoing in Flush with Concealed wall and making good of the concealed portion with earth connection. ( FP MCCB DB with IP43 Protection) ( for power loads exceeding 100A ) Higher End.

Supply and fixing of 7 segment 4 way 63A FP MCB sheet steel Horizontal Distribution Board (Higher end) with metal / acrylic door cover flush type /surface type fitted with busbars and neutral links with single /three phase MCB outgoings and separate 4 way provision for accommodating one no. 4 pole incoming 63 A FP MCB, 10kA, and another separate 4 way for accommodating one no. 63 Amps 4 pole MCB/ ELCB / RCD (totally 8 ways in one segment) ( 3x4ways in each segment ) and Seperate Provision for MCB / Isolators (totally 12nos) for sub incomers in 3 segments with label holder and provision for taking up cable for size not less than 35 sq.mm. with the following in flush with wall with earth connection only. i.63A 4Pole MCB - 1no. Incoming ii.32A 2Pole MCB - 3nos. Intermediate iii.20A 2Pole MCB - 6nos Outgoing

Metering Panel - Fabrication, Supply, Installation, Testing and Commissioning of all metal floor mounted 1ø and 3ø Meter Panel Board incorporated with the following. The cost of the foundation channels shall also be including in the rate. The Cost shall also includes unloading and positioning. Incoming 3Nos. 300Amps to 400A TP cutouts or 300Amps to 400A TPN MCCB with 250Amps neutral link properly fixed on the sheet steel with necessary accessories with 300Amps to 400A 4P Copper Busbar. The Phase busbar shall be 33x6mm and the neutral busbar shall be 33x6mm.The Board shall be provided with 2Rus of 25x6mm Aluminium busbars of earthing. Space for EB scope fixing 4 Nos of direct operated single/three phase dual source energy meter (Enercon/ ABB make) with RS485 Com Port with necessory accessories. 4 Sets of 200A TP MCCB with neutral link Outgoing properly fixed on the sheet steel. of interconnection between the coutout, MCCB and the Meter shall be done with16Sq.mm. Cu PVC insultated strandard copper conductor cable or spreader terminal with crimped type lugs / sockets, etc.RYB indicating Lamps of LED Clustered type and Control toggles switch per each phase shall be provided for the Main EB cut-out chamber door. CRCA sheet Thickness : 14SWG for door and Frames 16SWG for others. Foundation Channel - 3mm thick Cable Gland - 14SWG Painting: Powder Coated RAL 7032 and Black Color for the foundation channel.

Supply and run of 2 of 2.5sqmm (36/0.3) PVC insulated SC unsheathed Cu. Conductor of 1100V Grade in suitable PVC rigid pipe clamping on wall and ceiling with 1.00sq.mm cu wire for continuous earth wire connection complete.

Supply and run of 2 of 4 sqmm (56/0.3)PVC insulated SC unsheathed Cu.Conductor of 1100V Grade in suitable PVC rigid pipe clamping on wall and ceiling with 1.00sq.mm cu wire for continuous earth wire connection complete.

Supply and Laying of 4C x 10 sq.mm. PVC armoured LTUG cable in suitable size of 50mm HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good

Supply and fixing of brass cable gland suitable for 4C x 10sq.mm PVC armoured LTUG cable with earth connection.

Supply and clamping of 2C x 10 sq.mm PVC LTUG armoured LTUG cable on post or on wall with MS Clamps.

Supply and fixing of brass cable gland for 2cx 10 sqmm PVC armoured LTUG cable with earth connection.

Supply and clamping of 3 1/2C x 50 sq.mm PVC LTUG armoured LTUG cable on post or on wall with MS Clamps.

Supply and fixing of brass cable gland for 3 1/2C x 50 sqmm PVC armoured LTUG cable with earth connection.

Supply and providing cable end termination of 31/2C x 50 sqmm PVC LTUG Aluminium armoured cable with necessary aluminium cable sockets by crimping etc. with electrical connection complete.

Supply and clamping of 3 1/2C x 70 sq.mm PVC LTUG armoured LTUG cable on post or on wall with MS Clamps.

Supply and fixing of brass cable gland for 3 1/2C x 70 sqmm PVC armoured LTUG cable with earth connection.

Supply and providing cable end termination of 31/2C x 70 sqmm PVC LTUG Aluminium armoured cable with necessary aluminium cable sockets by crimping etc. with electrical connection complete.

Supply and clamping of 3 1/2C x 95 sq.mm PVC LTUG armoured LTUG cable on post or on wall with MS Clamps.

Supply and fixing of brass cable gland for 3 1/2C x 95 sqmm PVC armoured LTUG cable with earth connection.

Supply and providing cable end termination of 31/2C x 95 sqmm PVC LTUG Aluminium armoured cable with necessary aluminium cable sockets by crimping etc. with electrical connection complete.

Supply, Installation, Testing and Commissioning of 55" smart LED TV with following specifications a) Full HD 1920 x1080 (4K monitor) b) IPS panel c) Slim back light LED module d) 900 PMI e) Triple XD engine f) Dynamic scanning g) ANR h) True colour generator i) 8modes of picture j) picture wizardIII k) Real cinema 24P l) HDMI -3nos m) USB -3nos n) Built in LAN o) Magic remote p) Dimension 1242 x 724 x 55.1min(37). (Make: Sony/ LG /Samsung).

DESKTOP: Supply, Installation, Testing & Commissioning of Workstation Intel quad core, minimum i7 series, 4.6GHz, 8GB of RAM, 2GB Graphics card capable of 1280x1024 pixel resolution and 65K colours, 1 TB Hard disk drive, DVD ROM drive with additional HDMI cards suitable for multifunction operation for dual monitor. All software's loaded shall be genuine and shall be licensed to clients name, for life time.

Supply and Installation for 5KVA Inverter with Battery, Single Phase Inverter (Single Phase In & Single Phase Out) Capacity - System with Battery - 2Hours back up.

INTERCOM SYSTEM:

Supply and run of 2 pair telephone cable in suitable PVC rigid pipe clamping on wall and ceiling

Supply of Caller ID Telephone with Speaker.

Supply and installation of HYBRID IP EPABX System with 3 Trunk + 16 Analog Extensions. Expandable Up to 96 Analog Extension & 112 IP Port system.

Internet facility:

Supply and Clamping of CAT 6 armoured cable in suitable PVC Pipe 1" thick on wall / ceiling with connected PVC accessories with clamps, saddles etc., complete. (Between ethernet switch to camera and radio modem) i. Application : Primary (Campus), Secondary (Riser), Tertiary(Horizontal) IEEE 802.3 : 10Base-T; 100Base-T; 1000Base-T IEEE 802.5 16 MB; ISDN; TPDDI; ATM ii. Standards: ISO/IEC 11801 2nd ed.; IEC 61156-5 2nd EN 50173-1; EN 50288-6-1,EIA/TIA 568C.2, RoHS Compliant. Fire Rating: PVC : IEC 60332-1. iii. Conductor - Bare Copper Wire iv. Insulation - Polyethylene v. Twisting - 2 Cores to the pair vi. Cable lay up - 4 Core to the pair It has diameter of (23 AWG) 0.550 ± 0.015.Insulation : Polyethylene.GI wire of size is 0.90 ± 0.030mm.

Supply of LAN Box etc., complete.

Supply and fixing of RJ45 I/O Socket in module box with Single Face Plate for LAN Point etc., complete.

Supply and fixing of POE 8 port switch 10/ 100 / 1000 Base -T / 2 x 1000Base-FX / 20Gbps bandwidth / IEEE803.af/at compliant PoE+ / RJ45 supports auto MDI/MDI-X function / Auto negotiation speed, half/full-duplex / Store and forward / Max packet size: 10kbytes / Wide range power design (12~56VDC) / Operating temperature (-40 ̊C ~ +75 ̊C) / Reverse polarity protection / Resettable fuse to protect against overcurrent / IP-40 protection / EFT protection for power line. (Make:DLINK,NETGEAR/ TPLINK)

Supply of Wifi Extender etc., complete.

HVAC system

Supply and Installations of 20HP VRF outdoor units equipped with hightly efficient invertor scroll compressors, special acrylic precoated heat exchanger, low noise condensor fan, auto check function for connection error, auto address setting, with multiple outdoor units, including providing gas charging, pressure testing, leak testing, complete including cartage etc. as required. Refrigerant shall be R410A and all compressors shall be of inverter type only for better efficiency. The part load under normal operating conditions. The rate is inclusive of transport charges and other taxes extra complete. ( Make : Bluestar / Toshiba / Daikin / Samsung / LG / Hisense )

Supply, Installation, Testing & Commissioning of VRV / VRF indoor units. Max of TR and CFM specifications should be met in case of specific product descrepancies. The rate is inclusive of transport charges and other taxes extra complete

Panel with Cordless Remote Controller. Supply of Cordless remote controller with panels for Indoor units 2 TR & Above

Supply of Central controller capable of monitoring the each floor indoor units at one location in respective floors. The controller shall be capable of addressing each and every IDU and ODU and allow revision of set point (Touch screen panel)

Supply and fixing of Refnet joint kits for VRV/VRF indoor and outdoor units. The Quantity of refnet joints as mentioned in the tender drawings.

Supply and laying of Hard drawn 20 G Copper refrigerant piping with necessary fittings, insulation with 13mm thick class 'O' UV resistant Nitrile rubber tubing for Suction line

Supply and laying of Hard drawn 20 G Copper refrigerant piping with necessary fittings, insulation with 13mm thick class 'O' UV resistant Nitrile rubber tubing for Liquid line

POWER CABLES & COMMUNICATION CABLES

Supply and laying of 2 core 1.5 Sq.mm Copper cable from ODU to IDU in PVC conduit with necessary fittings for Control wiring & CRC Wiring.

Supply of 25 mm Drain Pipe

Supply of 32 mm Drain Pipe

Supply and fixing of 50mm thick Anti Vibrating Rubber Pads

Supply and providing of pipeline nitrle rubber insulation for Refrigerant and drain pipe lines.

Supply, fabrication and fixing of MS Channel for Mounting the Airconditioning Oudoor Unit.

Supply and filling of R 410 A Refrigerant Gas

PUBLIC ADDRESS & PROJECTOR SYSTEM FOR CONFERENCE HALL:

Supply and fixing of Confernce type P.A System Arrangements with necessary accessories

Supply and fixing of Mic for Chairman unit with necessary connections etc

Supply and fixing of Mic for Deligate unit with necessary connections etc

Supply and fixing of Conference controllerunit with necessary connections etc

Supply and fixing of 240W P.A Mixer Amplifier with necessary connections etc

Supply and fixing of Cordless Mic UHF

Supply and fixing of 8 pin conference mic Socket with modular box and front plate

Supply and laying of 8 Core 1.5Sqmm PVC Copper Conference cable

Supply and laying of 2 Core 1.5Sqmm PVC Copper Speaker wire

Supply and fixing of 30W wall speaker with necessary connections etc

Supply and fixing of 3200 Ansi Lumens Projector, XGA (1024 x 768) Resolution, Contrast Ratio : 4000:1 with necessary connections etc

Supply and fixing of 8' x 6' Motorized Screen with necessary connecting accesories etc

Supply and connecting of 20 Meter HDMI Cable

Supply and laying of 3 core 1.5 Sq.mm Power cable for Projector.

Supply and fixing of 3 feet Ceiling Mount kit with necessary accesories etc

Supply, erection and installation custom built 42U Rack with necessary accessories.etc.

Supply and fixing of fan for the above 42U Rack with necessary accessories.etc.

Supply and fixing of 3 meter length patch cord.

Interconnection, Testing & commisioning charges for the above works

LOTUS CONSTRUCTION (BID ID -1266822)

VESCON INFRASTRUCTURE PRIVATE LIMITED (BID ID -1266146)