SPECIAL REPAIR TO BLDG NO P 91 JCOs MARRIED ACCOMMODATION AT ADM AREA CPE ITARSI UNDER GE BHOPAL

Note :(i) Please refer Sch A/ BOQ Notes before quoting the tender for all phases/ items mentioned below. (ii) Amount of Schedule of credit shall be deducted offline

Demolition of un reinforced cement concrete of any description and in any position not otherwise specially provided for complete all as specified and direted.

Dismantling floor, hearth or wall tiling including cement morter beddind (but not backing removing seviceable tiles to store and rubbish off the premises complete all as specified and direted.

M&L for cement concrete (1:2:4), type B-1 using 20 mm graded stone aggregate as in roof kerbs or mud stops, bed blocks,benching etc including necessary form work complete all as specified and directed.

Demolition of unreinforced cement concrete in ground floor and paving not exceeding 15 cm thick (below or above ground level) complete all as specified and direted.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc. complete all as specified and direted.

M&L for 75mm thick, cement concrete (1:3:6) type C-2 using 40 mm graded stone aggregate as in sub base floor complete all as specified and direted.

M&L for 75mm thick, cement concrete (1:3:6) type C-2 using 40 mm graded stone aggregate as in plinth protection, surfaces finished even and fair without using extra cement as in plinth protection including provision of construction joints complete all as specified and direted.

M&L for 30 mm thick, cement concrete (1:2:4) type B-1 (using 20 mm graded gradded stone aggregate) as in sub base of flooring, surface finished rough to receive floor topping complete all as specified and direted.

M&L non-skid ceramic tiles coloured 7 to 8 mm thick (square/ rectangular), premium quality area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match colour of tiles over and including screed bedding or screed bed of 15mm thick in CM (1:6) complete all as specified and direted.

M&L for joint free non-skid ceramic tiles 8 to 9 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including screed bedding or bedding layer of 15mm thick in CM (1:6) complete all as specified and directed.

M&L for joint free non-skid ceramic tiles 8 to 9 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm,as in skirting or vertical surface set and jointed in neat cement slurry and pointed in white or coloured cement to match surfaces over and including backing coat layer 10 mm thick rendering in cement mortar (1:4) complete all as specified and directed.

M&L for glazed ceramic coloured (colour & shade as approved) tile 450x300x7mm thick on vertical surface such as skirting / dados set and jointed in neat cement slurry over and including 10 mm thick rendering in cement mortar (1:4) and pointed in white/ coloured cement with pigment to match the colour of tiles complete all as specified and directed.

M&L for 15-18 mm thick granite in single piece including nosing at front and sides in steps, jambs, pillars, window cills, cooking platforms, staircase and like with bull nosing in cm(1:4) including pointing in white cement(1:2) using marble dust with admixture of pigment to match with marble shade including making grooves for slip guard or steps,edge moulding,making 30 mm dia hole in cooking counter slab and green marble top for gas pipe over and including screed or bedding 15mm thick in CM (1:6) complete all as specified and directed.

Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified and directed.

M&L for rendering 10 mm thick in CM (1:4) mixed with integral water proofing compound as per manufacturer'r instructions over the padding concrete while still the concrete is still green, complete all as specified & directed.

M&L for water proofing treatment to roof surface including parapet wall comprising with the following steps:- (a) Applying evenly a tack coat of industrial bitumen 85/25 @ 1.2 kg per sqm over a coat of bitumen primer @ 0.30 ltr per sqm including preparation of roof surfaces complete all as specified and as directed. (b) APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) land on primed surface by forced application complete all as specified. Polymeric membrane shall be taken to a height of 60 cm (minimum) and then inserted inside the groove of parapet walls and shall be finished by a membrane flashing. c) Applying two coats of aluminium paint @ 0.2 kg/sqm complete all as directed. Note:- (i) Laying of APP based membranes shall be done by torch on method or as per manufacturer's instructions. (ii) A minimum overlap shall be 100mm length wise and 150 mm width wise of polymeric membranes respectively and sealed all over laps and joints as manufacturer's instructions.

M&L for cement concrete tiles 25cm x 25cm x 20mm thick, machine pressed, set and jointed in neat cement slurry over and including 15 mm thick screed bed layer or screed bed in cement mortar (1:4) and pointed in neat cement mixed with grey cement and pigment to match the shade of tiles complete all as specified and directed.

Demolition of brick work or stone/boulder masonary built in cement mortor including all quoins, arches, pillars etc complete all as specified and directed.

M&L for brick work with sub class 'B' bricks straight or curved on plan exceeding 6m mean radius built in CM 1:6 complete all as specified and directed.

All as per ser item No 19.00 here-in-before but except brick complete all as specified and directed.

Taking down cement plaster on brick walls of any description including racking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M&L for rendering 15mm thick in cement mortar (1:6) on fair face of brick walls or concrete surfaces, finished fair and even without using extra cement complete all as specified and directed.

M&L for rendering 15mm thick in cement mortar (1:4) on other than face of brick walls or concrete surfaces, finished fair and even without using extra cement using WPC complete all as specified and directed. Note:- WPC will be measured and paid separately.

Supply only integral water proofing compound (WPC), ISI marked complete all as specified and directed.

M&L for rendering 5 mm thick, cement plaster on ceiling surfaces in cement mortar 1:3 finished fair and even and smooth without using extra cement complete all as specified and directed.

M&L for preparation of new plastered surfaces of ceiling and applying two coats of white wash complete all as specified and directed.

M&L for preparation of old surfaces of ceiling and applying one coat of white wash complete all as specified and directed.

M&L for 2 mm thick wall care putty on wall newly plaster surface complete all as specified and directed.

M&L for preparation of newly plastered surfaces of wall and applying two coats coats of OBD over a coat of primer complete all as specified and directed.

M&L for preparation of newly plastered surfaces of wall and applying two coats coats of white wash complete all as specified and directed.

M&L for preparation of old plastered/unplastered surfaces of walls including brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil & greasy spots and applying one coat of white wash on wall complete all as specified and directed.

M&L for complete removal of old existing tratment on plastered surface of wall including and prepration for two coats distemper oil emulsion over and including 1 mm thick JK Birla wall care putty to make the surface even and smooth complete all as specified and directed.

M&L for applying two or more coats of 100% premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10sqm over new surfaces complete all as specified and directed.

M&L for complete removal of all existing treatment including preparation of old surface and applying two or more coats of 100% premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489-2004. Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) wiht silicon additives @ 1.43litre/10 Sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 Sqm complete all as specified and directed.

Taking down chowkhats or frame n exc 1.5 sqm each with shutters (without taking off shutters from the frame) including fittings complete all as specified and directed.

Taking down chowkhats or frame exc 1.5 sqm but n exc 4.00 sqm each with shutters (without taking off shutters from the frame) including fittings complete all as specified and directed.

Taking down shutters of size exceeding 1 sqm and n. exc 2 sqm each and removing from site to store or otherwise as complete all as specified and directed.

S&F for 30 mm thick flush shutters factory made solid core construction with block board core, plywood face panels, both side covered with decorative face veneer with lipping/frame to match complete all as specified and directed

S&F for 105x60mm size of pressed steel frame for door with one or more rebates including necessary fixing lugs, lock striking plates, hinges, hold fast(40x3mm) etc. complete size /profile of frame as per IS

S&F for 125x60mm size of pressed steel frame for door with one or more rebates including necessary fixing lugs, lock striking plates, hinges, hold fast(40x3mm) etc. complete size /profile of frame as per IS

S&F “RAJSHRI” Brand factory made 30mm thick 100% solid WPC ( Wood polymer Composite ) laminated wiremesh door shutter of required size comprising of virgin PVC resin of K Value 57-60 ( Suspension Grade ), Calcium Carbonate and natural fibers (wood powders/ rice husk/ wheat husk ) and non toxic additives, made from extrusion process WPC foam sheet single extruded ( Inner ) with having minimum density not less than 650 kg/cbm manufactured by "RAJSHRI" an ISO 9001 - 2015 Certified Company, having good screw holding capacity ( Screw Withdrawal strength of 2000 N ( Face ) & 1100 N ( Edge ), Minimum Compissive of 50 N/mm2, Modulus of elasticity 850N/mm2 and resistance of spread of flame of Class A category with Property of being Termite/ Borer Free.Water/ Moisture Proof and Fire Retardant. WPC to be Laminated with PVC foil of minimum 14 microns thick of approved design pasted on both faces of shutter. For fixing Mosquito mesh and XTN aluminium mesh combinely panel area of door except stiles and rails to be panelled with mesh with self tapping round headed scresws at required distance and edges covered with feathered pvc edge beading all around of mesh and fixing stainless Steel butt hinges of required size with necessary full body threaded star headed counter sunk SS Screws. All as per direction of Engineer -In-Charge, Material test certificate and authentication should be compulsory provided by the manufacturing company.

S&F for 1.00 mm thick, stainless steel plate rack of standard pattern of size 900 x 750 x 250 mm.The thickness of stainless steel sheet shall be grade of S 304 AISI including fixing to wall with 4 Nos 50mm screws & PVC rawl plugs complete all as specified and directed.

Supply and fixing for minimum thickness of powder coating 50 micron aluminium powder coated aluminium window having three track with aluminium section 92 mm X 31.75 mm (Weight bottom section 1.070 kg/m, top section 0.933 kg/m, shutter section 40 mm X 18 mm (weight of handle section 0.417 kg/m) interlock 0.547 kg/m mounted on bearing to slide on tracks plain anodized in approved shade including supply and fixing of 5mm thick plain glass and wire mesh, PVC track gasket, EPDM rubber gasket on glass of weather tightening along with locks, handle including sealing gap with marble surfaces with silicon sealants making it water proof in all manner Etc. complete all as specified and directed.

Supply and fixing for minimum thickness of powder coating 50 micron aluminium powder coated ventilator having fixed glass with aluminium section having section 75 mm x 50 mm (min weight 1.08 kg/m) glazing clear section (weight 0.109 kg/m) with plain anodized including supply and fixing of 5mm thick frosted glass making frame and glass water tightening and partly lovering including SS wire mess making it good etc. complete all as specified and directed.

S&F of pre-painted galvalume aluminum zinc coating GI based corrugated steel sheeting 0.50 mm thick of an colour having tensile strength of 550 Mpa (AZ-150) as in roof covering / cladding to wall, chajjas, etc. and fixed with self tapping screws complete all as specified and directed

S&F of framed work such as grills, gratings, etc with ends of bars shouldered and/ or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed.

S&F factory made single extruded WPC (Wood polymer composite) soild door/window /ceosetory windows and other frames/chowkat of size 45x85mm comprising of virgin PVC polymer of K value 58-60 (suspension grade) calcium carbonate and natural fibre (wood powder/rice husk/wheat husk) and fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minumum frame density of 750kg/cum screw withdrwal strenth of 2200 N (Face) and 1100N (Edge) minumum compressive strength of 58N/mm2, modules of elasticity 900N/mm2 and resistance to spread of flame of class A category with properly of being termite/border proof, water /moisture proof and fire retardant and fixed in position with MS hold fast/lug/SS dash fasterrs of required ida and length complete as per direction of Engineer in charge (MS hold fast/lug or SS dash fastteners shall be paid fo rseparatelly) Note:- WPC solid door/window frames, minus 5mm tolerance in dimension i.e depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made

S&F of 30mm thick factory made solid PVC moulded door shutter with wood free EPS , 28 to 30mm thick (stiles) with 2,4 or 6 raised panel design with 2mm thick moulded PVC sheet on the front face and 2mm plain colour PVC sheet on back face, suppling and fining in frame at site as per specification and drawing complete all as specified and directed.

S&F for framed brackets for chajjas of angles or tees with web and flanges cut to shape, drilled and counter sunk for screw, including bending and welding angles, as necessary, gusset plates, riveting, etc.. not exc 10 kg each brackets, conforming to Fe.290.Gde-E-165 (Brackets over 10 kg each to be measured under 'Structural Steel' complete all as specified and directed.

Dismantling of boarding, any description, fixed in any position with nails complete all as specified and directed.

S&F for block boards, grade 2 quality, interior grade, decorative type with decorative face veneer on one face and board fixed to timber/steel frame work with screw including if any damaged/broken of existing surface during the fixing arrangement of cabinet and making good existing surface with the same material complete all as specified and directed.

M&L for for fram work second class hard-wood in scantlings complete all as specified and directed.

S&F 12mm thick plywood No 7 grade veneered decorative plywood, grade 1 (with BWR resin) with decorative face veneers on both faces fixed with screws as cupboard shutter to timber/steel frame work complete all as specified and directed.

Cutting holes in brick walls in mud mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4

S&F100mm long hasp and staple, mild steel, wire type, aluminium anodised, including bolt to hinges plate and fixed with screws complete all as specified and directed.

S&F Extra over rates of block board or veneered particle board for external teak wood lipping, 6mm thick fixed with nails on 18/19 block board complete all as specified and directed.

S&F Extra over rates of block board or veneered particle board for external teak wood lipping, 6mm thick fixed with nails on 12mm thick plywood complete all as specified and directed.

S&F 30mm thick continous (piano) hinges of mild steel bright finish or electro galvanised with flap (when open) ,fixed with steel screw complete all as specified.

S&F for stainless steel clip on soft close clip on 3D hydraulic concealed hinges for full overlay door as kitchen cabinet complete all as specified and directed.

M&L for preparation of new steel surfaces of any description, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of redoxide priming complete all as specified.

M&L for one coat of synthetic enamel paint on old painted wooden surfaces of any description over 10cm width or girth including preparation of old painted wooden surfaces of all as specified and directed.

All as per item No.61.00 here-in-before but on steel surfaces complete all as specified and directed.

S&F 100 mm size mild steel butt hinges, medium weight complete all as specified and directed.

S&F aluminium tower bolts 150 mm long and fixed with steel screws complete all as specified and directed.

S&F aluminium bow handle 150 mm long and fixed with steel screws complete all as specified and directed.

S&F alluminium, anodised handles 100 mm long fixed to Cupboard etc complete all as specified and directed.

S&F 300 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified.

S&F 150 mm floor door stopper of aluminium alloy body and tongue, anodized with hard drawn steel spring complete all as specified and as directed.

S&F 300 mm mild steel ordinary rat tail spring including roller and roller plate complete all as specified.

M&L for cutting chases, pinning in, making good to facings where required for brick wall and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth complete all as specified and directed.

Taking up or down existing steel water tubing, 15mm bore alongwith connections fixed/laid in any situation, complete all as specified and directed.

All as per ser item No 71.00 here-in-before but 20 mm bore tubing complete all as specified and directed.

M&L for GI steel water tubing, 15mm bore, medium grade galvanized with all fittings and fixed to walls and celling or laid in floor, complete all as specified.

All as per ser item No 73.00 here-in-before but 20 mm bore tubing complete all as specified and directed.

S&F in repair stop valves, fancy type, CP with long shank and cup ( concealed type ), screwed both ends for 15mm bore of iron pipe or for union and fixed all as specified.

S&F in repair gunmetal gate valve of 20mm dia with iron wheel head screwed both ends for iron pipe complete all as specified and directed.

S&F in repair bib taps, fancy type CP, screwed for 15mm bore of iron pipe or for brass ferrule and fixed all as specified.

S&F in repair 15 mm bore, stop valves/angle cock, fancy type cast copper alloy, screwed down, high pressure,with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed fixed all as specified.

S&F in repair vitreous china wash basin, white/ coloured, flat back, size 550x400mm including PTMT waste fittings, 32mm bore size etc. and making good disturbed surfaces to match with the existing complete all as specified.

S&F in repair 15mm bore, pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe etc complete all as specified and directed.

S&Fin repair low density polyethylene (LDPE) pipes 32mm bore of pressure rating 6 kgf/sqcm complete all as specified and directed.

S&Fin repair PVC connections 15mm size with PTMT nuts of length 450 mm complete all as specified and directed.

S&F 20mm dia Nipple suitable for HDPE water tank. (Minimum weight 15 mm-38gms/20mm45gms /25mm- 65 complete all as specified and directed.

S&F 500 ltr capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position including 20mm bore ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe incl dismantling existing water storage tank complete all as specified in SSR Part-I complete all as specified.

S&F in repair vitreous china squatting pan, Orissa pattern, size 580x440mm white/ coloured with integral foot rests including flus pipe and connection to trap and to flushing pipe, anti-syphonage pipe, etc. complete all as specified and directed.

S&F in repairs PVC 10 litre capacity valveless syphonic action type, flushing cictern, low level, white/ coloured with inlet, ball valve, float and handle including brackets and connection to pipe etc. complete all as specified and directed.

S&F in repair 125 mm chromium plated, shower rose with or without swivel joints any size including fixing to steel pipe or union complete all as specified and directed.

S&F in repair towel rail, 20mm dia brass chromium plated, 600mm long with fancy type brass chromium plated brackets on both sides and fixed to walls with steel screws and wooden/rawl plugs as in repairs complete all as specified.

S&F in repair cromimum plated SS, soap dish (not less than 1mm thick) of type as directed, fixed to walls with chromium plated brass screws with wooden/rawl plugs,in repair complete all as specified and directed.

S&F in repair sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and astes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm complete all as specified and directed

Dismantling upto 75 bore of cast iron, PVC/AC/cement concrete pipes, jointed in cement mortar and taking out from wall/trenches, if required.

S&F 75mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls or laid in trenches complete all as specified and directed.

S&F 110mm dia PVC (SWR) pipes single socketed in any length with rubber ring jointsfixed to walls or laid in trenches complete all as specified and directed.

S&F 75mm dia PVC (SWR) bends any radius with solvent cement complete all as specified and directed.

S&F 110 mm dia PVC (SWR) bends any radius with solvent cement complete all as specified and directed.

S&F 75mm dia Junction single (single or double T) equal or unequal with solvent cement complete all as specified and directed.

S&F 110mm dia Junction single (single or double T) equal or unequal with solvent cement complete all as specified and directed.

M&L PVC (SWR) floor trap 75 mm, plain with PVC grating including jointing with solvent cement etc., complete all as specified and directed.

S&F in repairs, mild steel, curtain rod powder coated with fixing side brackets, end cups, rings @ 10 Nos per running metre and fixed with PVC rawl plugs & steel screws as in repairs complete all as specified.

M&L for 15 mm thick rendering over concrete surface of sunken floor in CM 1:3 on wall as well as sunken floor finished even and smooth without using extra cement using WPC complete all as specified and directed. Note:- WPC shall be measured and paid separetely.

M&L for water proofing treatment to RCC sunken floor including wall comprising with the following course of treatment/ specifications form bottom to top:- (a) Applying evenly a tack coat of industrial bitumen 85/25 @ 1.6 kg per sqm over a coat of bitumen primer @ 0.40 ltr per sqm including preparation of roof surfaces complete all as specified and as directed. (b) APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) land on primed surface by forced application complete all as specified. Note: (i) Laying of APP based membranes shall be done by torch on method or as per manufacturer's instructions. (ii) A minimum overlap shall be not to be less than 150mm of polymeric membranes and sealed all overlaps and joints as manufacturer's instructions. (iii) All CI/PVC traps in sunken slabs to be enclosed with PCC type B1, 1:1.5:3 using 20 mm gradded stone aggregate (min 15 cm) all round.

M&L for Cement concrete (1:5:10) type E-2 using 40 mm graded stone aggregate as in filling in sunkan slab or as in sub base, mass concrete complete all as specified.

Demolition of reinforced cement concrete in any position complete all as specified.

M&L reinforced cement concrete nominal mix (1:2:4),type B1 using 20mm graded stone aggregate as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified.

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work not exceeding 200mm thick (Horizontal or sloping) rough surfaces of concrete all as specified and as directed

S&F mild steel TMT bars as in reinforcement 10mm dia and over, cut to length, bent to shape required including cranking, bending spirally for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified & directed.

S&F0.80mm thick, mild steel plain black sheet as, covering to door shut ters, covering to door chowkats (frames), chullah hoods, water tanks, water troughs, ducts, urinal troughs and funnels, etc. cut to size edges beaded if directed, holes punched, including round headed screws, clout nails or rivets and fixed to wood or steel members, etc., with plain 40 mm lap joints or welded/ riveted seams including bending, turning up, mitred angles, stopped ends, outlets, etc. as required

M&L for 75mm thick PCC 1:3:6 type C-2 (using 40mm graded aggregate) as in pavement/plinth protection, plinth protection shall be laid in alternate bays finishing surface even and smooth without extra cement complete all as specified and as directed.

Forming Contraction (Dummy) joints 65mm deep x 10mm wide, filled with sealing compound grade 'A' complete all as specified and directed.

M&L for Cement concrete type C-2, 1:3:6 (40mm graded aggregate) as in Cement concrete in surface channels and drains complete all as specified and directed.

Extra performing fair finished drain or channel 30cm inner girth in cement concrete using extra cement including forms, moulds, mitred/stopped ends etc. complete all as specified.

Cutting into existing drains for connecting new drains 150mm dia making good to existing drain and making good

M&L PCC type C-1, 1:3:6 ,using 20mm graded aggegate in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs not provided for in complete all as specified and directed.

M&L for cleaning the blockage of bathroom/kitchen by cleaning the nanhi traps / gully traps of all the mud / sludge and getting out washing throughly traps, CI waste pipe by opening the cleaning eyes and depositing the sludge in a pit of suitable size at a distance not exceeding 100m from the gully trap and covering the same with the soil obtained from excavation of pit including excavation and earth work complete all as specified and directed.

Taking down carefully aluminium / copper point wiring with surface/ concealed PVC conduit or wooden batten ( light, fan, socket, bell or power ) including making good disturbed surfaces of walls, floors etc including putty and one coat of similar paint to match the existing surface complete.

M&L for concealed point wiring using approved color coding as per IS (Red, Black and Green for single phase circuits) with multi-stranded copper conductor stranded copper conductor, 1.5 sqmm nominal cross sectional area, single core, PVC insulated and unsheathed FRLS cable 1100 Volts grade, IS-694 marked with valid CML no PVC conduit and conduit accessoriees on wall/roof/floor etc. ISI marked with valid CML No. (IS-9537-1983 for conduits and IS:3419:1976 for conduit accessories), with metal sunken box, modular cover plate for fixing of modular switches, sockets and fan regulators etc, including PVC insulated multistranded copper conductor 1.5 sqmm nominal cross sectional area single core FRLS cable as earth continuity conductor to common earth and connecting to earth dolly complete all as specified and directed at site for the following:

(a) One light point/fan point controlled by one switch complete all as specified and directed.

(b) One light point controlled by two way switch complete all as specified and directed.

(c) One socket outlet 5 Amps controlled by one switch on the same board complete all as specified and directed

(d) One socket outlet 5 Amps controlled by one switch on independent board complete all as specified and directed

(e) One bell / buzzer controlled by one bell push complete all as specified and directed.

All as per item No. 117.00 here-in-before but with 2.5 sq mm multi stranded copper conductor cable for one 15 Amps socket outlet controlled by one switch on independent board and 1.5 sq mm PVC insulated multisranded copper conductor cable as continuous earth wire complete all as specified and directed.

Supply and fix single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB SP/DP 10-20 Amps with complete accessories all as specified and as directed and directed.

Material and labour in repairs for sub main wiring with two single core 6.0 sqmm multi stranded copper conductor, FRLS PVC insulated, unsheathed cable including rigid non metallic PVC conduit medium grade, ISI marked, 20 mm dia for sub main wiring including 6.0 sqmm FRLS PVC insulated and unsheathed stranded copper conductor as earth wire in concealed in wall of make & maching the existing surface make & maching the existing surface and making good to the disturbed surfaces to match the existing surfaces complete including taking down existing unserviceable submain of any size all as specified and directed. Note:- Two runs of 6.0 sqmm copper conductor cable, one run of 6.0 sqmm copper conductor earth wire and one run of of pvc conduit measured is one length.

S &F ding dong bell AC, 240 volts single pole complete all as specified and directed.

S&F ceiling rose surface bakelight two to three terminal complete all as specified and directed.

S&F modular bell push, 6A, 1 module complete cover plate complete all as specified and directed.

S&F modular switch 1 way 6A, 240 volts 1 module complete all as specified and directed.

S&F modular switch 2 way 6A, 240 volts 1 module complete all as specified and directed.

S&F modular switch 1 way 16A, 240 volts 1 module complete all as specified and directed.

S&F modular socket, 6A - 2/3 pin combined 2 module complete all as specified and directed.

S&F modular socket 6A/16A - 2/3 pin combined 2 module complete all as specified and directed.

S&F modular fan step regulator, 120W, 240 volts 2 module complete all as specified and directed.

Supply and fixing lamp holder, PVC/polycarbonate type with back plate suitable for batten fittings complete all as specified and directed.

S&F 09 Watt LED bulb with inbuilt battery and control circuit, battery backup upto 4 hrs in white colour with maximum lumen output (850 lm) and colour temp 3000 K complete all as specified and directed.

Supply and fixing LED lights batten fitting 1x 20W, 220V,AC decorative box type with driver, aluminium housing, efficient heat dissipation, IP 20, Surge protection upto 2.5 KV, PF >0.9, rated CCT 6500K connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed.

Supply and fixing LED light batten fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver, aluminium housing, efficient heat dissipation, IP 20, Surge protection upto 2.5 KV, PF >0.9 including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

S&F LED light fitting 10W bulk head luminaires IP-65, surge protection upto 2.5 KV, pressure die-cast aluminium housing & ring for sturdiness & corrosion resistance, PF >0.9, High lumen efficacy LED with viewing angle of 120° used to enhance the lumen output, connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

Taking down energy meter/main switches of any size after disconnecting supply and kept in safe custody, taking down & remove the old wooden meter box from site, plastering the existing disturbed wall surface including colour wash and refixing the Meter/Main Switches again on new wooden board of required size as per site incl painting of the board with connection complete all as specified and directed.

Taking down MCB DBs including MCBs of all sizes after disconnecting supply complete all as specified and directed.

S&F sheet metal enclosure MCB DB, 4 way, tripple pole and neutral, IP-54, 415 volts factory made double door flush type complete all as specified and directed.

Supply and fix for sheet metal enclosures for SPN DB's 240 volts, factory made double door flush type, IP-54 protection and all as per IS-8623, made from sheet metal 12 way 200 Amps rated bus bar to be fixed with wall all accessories complete all as specified and as directed.

S & F MCB single pole 240 volts 6 to 32 amps complete all as specified and directed.

S&F MCB double pole, 240 volts 16 to 40 Amps complete all as specified and directed.

S&F MCB, TPN, 63 Amp, 440 Volts 25 breaking capacity complete all as specified and directed.

M&L for earthing complete with glavanised steel earth plate elactrode 600x600x6.0 mm thick buried directly in ground (Earth pit not less than 2.25 mtr deep below ground leves) with top edge of the plate not less 1.5 mtr deep below normal ground level connected to galvanised earth lead wire 4.0 mm dia by means of nut , bolt, check nut and washer of galvanised iron or of steel, earth lead protected by 15 mm dia GI pipe light grade watering pipe 20 mm dia GI light grade GI wire meshed funnel alternate layer of charcoal and salt PCC chamber , reassed for and including RCC cover including all necessary excavation and earth work, earth wire connected to main switch board, testing the earthing after completion all as specified and shown in electric plate No 5 of MES SSR Pt-I 1991 print and as directed. Note:- (i) Cost of excavation, removing, PCC chamber, 15mm bore, medium grade, GI protection Pipe (7.5 Meters long). (ii) On testing after completion of earthing if the desired earth resistance is not obtained, earthing will be re-done by the contractor at his own risk and cost to the entire satisfaction of Engr-in Charge.

Supply and fixing LED Bldg/street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing with heat sink, surge protection upto 4 KV, IK 08 protection, PF>= 0.95, rated CCT 5700K and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 66 protection and GI pipe 40 mm dia, light grade, for mounting bracket bent to shape 1.50 RM and fixing arrangement with two Nos of MS clamps set, nut bolts, washers of suitable size complete all as direcetd and as specified.

Supply & fix of solar gate light, 5 Watt with Solar Panel output 3.7 W, battery capacity 2.5 Ah, battery backup upto 8 hrs, IP65 rating with inbuilt Solar Panel, LED light and lithium Battery with charge controller all as directed.

Supply, laying testing and commissioning of heavy duty XLPE cable of size 25 Sqmm 3.5 core, 1100 volts grade, passing through GI pipe with aluminium conductor stranded polyethylene insulated, conductor served with and including sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheathed complete including taking down existing unserviceable UG cable of any type and size all as specified and directed.

Excavation in trenches in any type of soil (loose/ hard) not exceeding 1.5 Mtr wide and not exceeding 1.5 Mtr in depth and getting out for foundation of pole, laying under ground cables etc and getting out complete all as directed.

M&L sand filling in trenches for cable cushioning with clean, dry and unwashed sand free from sharp particles including gently punning around cable complete all as specified and directed.

Supplying and laying Class LV, Type I, flat, size 250mm x 150mm x 40mmfor cable protection cover as per IS 5820, laid flat and dry in trenches over the cable perpendicular to the direction of cable complete all as specified and directed.

Returning filling in, with the earth including spreading, levelling, watering and well ramming in layers and not exceeding 25 cm in layer complete all as specified and directed.

Removing surplus soil to a distance not exceeding 50 Mtr and deposting where directed at a level not exceeding 1.5 Mtr above the starting point complete all as specified and directed.

M&L of GI pipe, light grade, 50 mm dia bore with all fittings and fixed complete to wall, to pole or laid in trenches and road crossing complete including taking down unserviceable GI pipe of any size complete all as specified and directed.

Supply, jointing, testing end termination jointing kit heat shrinkable out door type, suitable for LT 1100 Volts grade cable of size 25 Sqmm to 50 Sqmm 3.5 core complete all as specified and directed by Engr-in-Charge.

Taking up or down old unserviceable 25mm dia, GI pipe medium grade galvanised with all fitting laid in trenches/on wall /floor /ceiling with clamps complete all as specified and directed.

Supply & fixing galvanized iron water tubing 25mm dia, medium grade with all fittings such as sockets, bends, elbows, tees, short pieces, connectors, back nuts, diminishing pieces, caps, plugs and unions etc.,, laid in trenches / fixed to walls and ceilings or laid in floors, complete all as specified and directed.

M&L Gun metal globe or gate valves class 2 with iron wheel head , screwed both ends for iron pipes and fixed of following sizes :-

(c) 25 mm dia

(d) 20 mm dia

Cutting existing water supply main line in position for insertion of specials / fittings viz Tee etc. of suitable size for making branch connection including testing after completion complete all as specified and directed.

Deduct Schedule of credit (calculation will be done off line) Rs. 37518.00