REPAIRS TO SEEPAGE/LEAKAGE AND CERTAIN MISC B/R WORKS IN MD ACCN, DOOR TO DOOR MAINT, CLEANING OF OVER HEAD TANKS, CLEARING BLOCKAGE IN WC, TOILETS OF MD/OTM BLDGS, REPAIRS TO INTERNAL WIRING, FANS, GEYSERS, SPLIT ACs AT DGQA UNDER GE NORTH BLORE

Amount

Note:- (a) Contractor shall detail his supervisor to office of AGE B/R (NORTH) daily by 9.00 AM who will report to concerned JE B/R /Engineer-in-Charge to receive all complaints related to (Plumbing / Carpenter / Sewage etc) of entire area under this contract. (b) Contractor shall provide service providers (sweepers) separately for all the Complaint cell as per the complaints list given along with all requisite tools, equipments, including safely measures for attending complaint and ensure completion report by 5.00 PM same day. (c) Complaint/blockage cleared any number of times on same day and at same location shall be treated as one complaint. (d) Please note that all the complaints relating to internal plumbing/sewage (WC/bath/kitchen etc) shall be attended within same day (within 12 hour). (e) In case any complaint pertaining to Plumbing/Sewage issue is not attended on same day, penalty @ Rs. 100/- per complaint shall deducted from contractor payments.

Taking down shutters of any description exceeding 1 Sq m but not exceeding 2 Sq m complete all as specified and directed

Re-securing or easing & adjusting without taking down shutters of any description exceeding 1 sq m but n.exc 2 sq m each complete all as specified and directed

Taking down chowkat (without taking of shutter from the frame) not exceeding 1.5 sq m each including making good the disturbed surface in CM 1:3 all as specified and directed

All as per Item No 3 above, but exceeding 1.50 sq m and not exceeding 4.00 sq m each

Demolition of cement concrete and paving not exceeding 15 cm thick (below or above ground level), removing debris to locations as directed by Engineer-in-Charge, complete all as specified and as directed.

Demolition of brick work / stone masonry / pack block masonry built in cement mortar of any description, removing debris to locations as directed by Engineer-in-Charge, all as specified and directed.

Taking down cement plaster on brick or concrete or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc., complete and removing debris to locations as directed by Engineer-in-Charge, complete all as specified and as directed.

Material and labour, for Pre-cast cement concrete block masonry with grade ‘C5’ solid blocks exceeding 10 cm in width, having minimum compressive strength of 50 Kg / Sq cm as per IS 2185 (Part- I) 2005 and set in CM 1:6 complete all as specified and as directed.

Material and labour for, brick work, with subclass 'B' bricks straight or curved on plan exceeding 6m mean radius, built in cement mortar 1:6 complete all as specified and as directed

Labour for, brick work, with serviceable bricks obtained form demolition, straight or curved on plan exceeding 6m mean radius, built in cement mortar 1:6 complete all as specified and as directed

Material and labour for, Solid PVC door frame (Single rebated) of size 60 mm x 30 mm made out of solid foam with homogeneous fine cellular structure having smooth outer integral skin with suitable metal stiffener and fixed with 100x8 sheet metal CSK screws complete all as specified and as shown on drawing (Note :- Door frame shall be water proof, termite proof, elegant and should have excellent screws holding strength to fix hinges and hold doors properly for a long life) complete all as specified and directed

Material and labour for, Factory made solid PVC moulded door shutter, 28 to 30mm thick (stiles) with 2,4 or 6 raised panel design with 2mm thick moulded pre-laminated PVC sheet on the front face & 2mm plain colour PVC sheet on back face supplying and fixing in frame at site as per specification & drawing with wood free EPS .

S&F 2nd class hard wood plain, solid, straight chowkats and frames, clean sawn, frame rebated on the solid , rounded or chamfered, put together with glue pinned at joints etc complete all as specified and as directed

S&F Flush door shutters 35mm thick, factory made as per IS:2202 (Part-I 1999) solid core construction, with block board core with decorative face veneer both faces with lipping/frame to match as per drawing fixed to chowkats all as specified and directed

S&F 2nd class hard wood 35 mm thick made glazed and skeleton shutters open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitered beads for securing glass, etc, size of members of shutters as specified in SSR Part-1, Section 8, clause 8.24 (a) kiln seasoned and chemically pressure treated complete all as specified and as directed

Supply and fix, stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.18 mm, fixed with mild steel screw & bolts all as specified and as directed.

Supply and fix in repairs, stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.18 mm, fixed with mild steel screw & bolts all as specified and as directed.

Taking down tubular curtain rod, supply and fixing drapery rod, decorative type, made of 25 mm dia stainless steel (wall thickness not less than 0.63 mm), wood finish, colour and pattern as approved by GE, complete all as specified and as directed. (Note : Price shall not be less than 100/- per RM)

Taking down old unserviceable brackets, Supply and fix stainless steel type brackets suitable to hold the curtain rod with sofio phenol (Lotto) and wooden round blocks for curtain rod of 25mm dia, decorative type fixed with steel screws and PVC cleats complete all as specified and as directed.

Supply and fix in repairs, 100mm Aluminium anodized barrel tower bolts of extruded section complete all as specified

Supply and fix Aluminium anodized barrel towel bolts of extruded section of length 150 mm all as specified and as directed.

Supply and fix in repairs, Aluminium anodized barrel towel bolts of extruded section of length 150 mm all as specified and as directed.

Supply and fix Aluminium anodized barrel towel bolts of extruded section of length 200 mm all as specified and as directed.

Supply and fix in repairs, Aluminium anodized barrel towel bolts of extruded section of length 200 mm all as specified and as directed.

Supply and fix Aluminium alloy anodized sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections including taking down old sliding door bolt 300 mm all as specified and as directed.

Supply and fix in repairs, Aluminium alloy anodized sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections including taking down old sliding door bolt 300 mm all as specified and as directed.

Supply and fix extruded aluminium alloy handles cast type anodized of size 150 mm all as specified and as directed.

Supply and fix in repairs, extruded alloy handles fabricated type anodized of size 100 mm all as specified and as directed.

Supply and fix in repairs, extruded alloy handles fabricated type anodized of size 150 mm all as specified and as directed.

Supply and fix stainless steel, butt hinges 100 mm long, fixed to door frame and shutter, all as specified and as directed.

Supply and fix, butt hinges medium weight cold rolled mild steel of size of hinges 100mm all as specified and as directed.

Supply and fix in repairs, butt hinges medium weight cold rolled mild steel of size of hinges 100mm all as specified and as directed.

Supply and fix in repairs, Hasp and staple safety type of size 100 mm of aluminium anodized all as specified and as directed.

Supply and fix in repairs, 100 mm size Mortice rim lock (4 lever), vertical type, brushed steel suitable for 25 to 40 mm thick doors screwing complete all as specified and as directed.

Supply and fix in repairs, 40 mm dia cupboard knobs fixed with nut, screw and washer of Brass, polished complete all as specified and as directed.

Supply and fix 150 mm floor door stopper of aluminium alloy powder coated, with hard down steel spring all as specified and as directed.

Supply and fix in repairs, 150 mm floor door stopper of aluminium alloy powder coated, with hard down steel spring all as specified and as directed.

Supply and fix in repairs, door closer hydraulically regulated designation No.3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 Kg of aluminium (Die cast body) complete all as specified and as directed.

Supply and fix mild steel 300mm, ordinary rat tail rod pattern spring hinges, including roller and roller plate complete

Supply and fix in repairs, mild steel 300mm, ordinary rat tail rod pattern spring hinges, including roller and roller plate complete

Supply and fix in repairs, Magnetic ball catches with 8mm dia steel ball, and brass body and striking plate including letting in and fixed complete all as specified and as directed.

Taking down unserviceable boards as in shelves of cupboards, doors, etc., providing material and labour for 18 / 19 mm thick Pre-laminated particle board, interior grade, pre-laminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work, alround 6mm thick teak wood fillets fixed in kitchen Cabinet or cupboards all as specified.

Supply and fix in repairs, second class hardwood, plain fillets square, rectangular or triangular in section clean sawn, secured with nails or brads, fixed to cupboard shutter, cross sectional area not exceeding 3 sq cm all as specified and directed.

S&F Box type Steel Windows/Ventilators double side shutters 4 mm thick sheet glass and stainless steel wire cloth with 0.36 mm nominal dia of wire and average width of aperture 1.18 mm. (Windows side hung type, Ventilators top hung) pressed steel frames made out CRC Sheet of 80x60x1.25mm double rebated, Shutters box type made out of CRC Sheet of 40x20x1.0mm, windows & ventilator shutter fixed made of glass and gauge fixed with box type hinges, Aluminium die cast handles for glass shutters, Iron flat type handles for mesh shutters, Telescopic stays, etc complete all as specified including 12mm square guard bars/grill welded with steel frame (100c/c horizontally) all as specified and directed by Engineer-in-Charge. NOTE: (i) Payment under this item will be make combined for steel frames, steel shutters and Guard bard / Grill, However unit rate quoted shall deemed to include cost of beading, fittings such as handles, hinges, Telescopic stays, locking arrangements and fixing of glass and wire mesh etc. (ii) Weight of Grill/Guard Bars, handle, hinges and locking arrangements shall not be accounted for payment purpose . (Note : All Windows/Vent design as per CECZ TD drg No 539)

Supply and fix powder Coated aluminium ventilator shutters, including 4 mm thick figured glass, louvers at top and fixed at bottom, without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodized aluminium snap beading, screws, anodized complete all as specified and as directed. (Size of ventilator 0.60 m x 0.90 m) Note :- Figured glass and wire gauge shall be deemed to be included in quoted rate

Supply and fix powder coated 3 TRACK aluminium sliding window with frame and shutters (2 Nos glazed shutters and one No wire mesh shutter), without sash bars, aluminium sections weighing not less than 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, powder coated aluminium snap beading, screws, self closing clips, handles, etc., complete all as specified. Note :- (i) Sheet glass and wire gauge shall be deemed to be included in quoted rate (ii) Thickness of glass shall not be less than 4mm. (iii) Stainless steel wire cloth 0.36 mm nominal dia of wire and acerage width of aperture 1.18mm

S&F grid suspended false ceiling grid system of size 600x600mm with main runner 29x24.7x0.8mm cross tee 29x24.7x0.8mm and wall angle 22.2x22.2x0.65mm. Ceiling suspended with 3mm dia GI wire hanger fixed with steel dash fastener, butter fly clips, hold down clips etc (Main runner, cross tee& wall angle of MS galvanized with PPPCGS) including 4mm thick HPSC self textured design pre primer non asbestos fibre cement building board fixed to false ceiling complete including taking down old ceiling of any description .

Hacking out old broken glass of any thickness, size, quality or description from metal frame including punching or drilling out old glazing pins/spring clips all as specified and as directed.

Material and labour for 4 mm thick Sheet glass, ordinary quality and glazing with oil putty in squares not exceeding 0.5 sq m in each pane including necessary scaffolding and staging externally for up to four storied bldg all as specified and as directed.

Material and labour for 3 mm thick Sheet glass, ordinary quality and glazing with oil putty in squares not exceeding 0.5 sq m in each pane including necessary scaffolding and staging externally for up to four storied bldg all as specified and as directed.

Material and labour for 4 mm thick figured glass, pin head type and glazing with oil putty in squares not exceeding 0.5 Sq m in each pane all as specified and as directed.

Material and labour for, preparing new wooden surface of any description, not other wise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer etc complete all as specified and as directed

Material and labour for, preparing new steel surfaces of any description, over 10 cm width or girth, applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and as directed

S&F framed work as in doors or gates of angle or other sections with gusset plates, rails braces, etc complete drilled for fixing of steel sheeting or other covering, doors etc, to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings(exclusive of steel sheeting or other covering, running rails and guides) and hanging ; also fastening and fixing complete including painted with one shop coat of zinc chromate primer paint (including preparation of surface) at contractors workshop/factory before fabrication complete all as specified and directed

M&L for providing and laying water proofing treatment to sunken portion of WCs, bathroom and kitchen etc by applying cement slurry mixed with two component Elastomeric Acrylic based polymer modified cementitious composite compound coating of make as approved in TI 5/2003 including demolition and removal the same from site of existing treatment of any type. The following procedures to be adopted during the execution of work :- (i) Demolition of existing treatment of any type including cleaning and removal of debris from site. (ii) First layer of slurry of cement @ 0.488 kg/sq m mixed with Acrylic based polymer modified cementitious composite compound @ 0.253 kg/sq m. The layer will be allowed to air cure for 4 hours. (iii) Second layer of slurry of cement @ 0.242 kg/sq m mixed with Acrylic based polymer modified cementitious composite compound @ 0.126 kg/sq m. The layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. (iv) 20mm thick screed in cement mortar 1:3 mixed with liquid water proofing compound as per manufacturers instructions above the treated area. Contd/-- 56.00

Sl Item No 55.00 Contd., (v) Ponding the treated portion at least 48 hours. if any leakage/seepage observed the entire procedures will be repeated without any extra cost. (vi) Provide 40mm dia light grade GI spout at the lowest point with 30cm projection beyond the out face of the wall. (vii) Sunken portion shall be filled with lean concrete 1:5:10 type E-2(using 40mm graded stone aggregate). Note :- (i) The sunken slab sloped towards outer face so as the drain the water to GI Spout pipe. (ii) Coving shall be provided at the junction of slab with the wall. (iii) Nahani trap shall be 10mm below finished floor level. Ensure the drain of pipe dia is larger than the nahani trap size. (iv) The outer end of the spout should be chamfered. v) Mode of measurement shall be plan area of sunken slab.

Demolition of existing roof treatment of any type including cement plaster 15 mm thick and providing screed bed/rendering 10mm thick in CM (1:3) mixed with and including supply of approved water proofing compound as per manufacturers instructions by removing all loose gravel, dirt, oil, grease and foreign materials by jet or dry air, cleaning the surfaces mechanically or by grinding to make it smooth and applying APP modified water proofing membrane as per IS 1654-2017/IS 16352-2017 , 3mm thick and weighing not less than 3.60kg/Sq m reinforced with non woven polyster/HMHDPE matt black finished over compatible primer/bonding bitumen @ 0.40 Litre/Sq m and torch applications of membrane with 75mm side overlap and 100mm end lap after necessary preparation of surface complete as per manufacturer's instructions and applying a coat of solar reflective bituminous aluminum paint on top @ 0.10 litre/sq m complete all as specified and directed.

Material and labour for, 25 mm thick, Plain Cement concrete type B0 1:2:4 (12.5 mm graded aggregate) as in floorings, with surfaces, finished even and fair complete all as specified and as directed

Demolition of floor, hearth or wall tiling including cement mortar bedding (including backing), and removing the rubbish to locations as directed by Engineer-in-Charge, and providing Material and labour, for non-skid Ceramic coloured tiles 7 to 8 mm thick (Grade B-IIA), area of each tile exceeding 0.06 sq m but not exceeding 0.11 sq m, as in flooring, set and pointed in white or coloured cement to match colour of tiles over and including 15 mm thick screed bed in CM (1:6) complete all as specified and as directed.

Demolition of floor, hearth or wall tiling including cement mortar bedding (including backing), and removing the rubbish to locations as directed by Engineer-in-Charge, and providing Material and labour, for non-skid Ceramic coloured tiles 8 to 10 mm thick (Grade B-IIA), area of each tile exceeding 0.18 sq m but not exceeding 0.36 sq m, as in flooring, set and pointed in white or coloured cement to match colour of tiles over and including 15 mm thick screed bed in CM (1:6) complete all as specified and as directed.

Demolition of floor, hearth or wall tiling including cement mortar bedding (including backing), and removing the rubbish to locations as directed by Engineer-in-Charge, and providing Material and labour, for coloured Glazed ceramic printed tiles, of size 450 x 300 x 7 mm thick (Grade B-IIA) as in vertical surfaces such as skirting, dado etc., set and jointed in neat cement slurry and pointed in epoxy grout to match with the colour of tiles, laid over and including provision of backing coat of 10 mm thick rendering in CM 1:4, complete all as specified and directed.

Demolition of stone slabs of any thickness and in any position, providing material and labour, for 18 to 20 mm thick Granite work (of any type), table rubbed and mirror polished), in single piece in steps, jambs, pillars, window-cills, cooking platform and like set in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, making hole for gas pipe, edges made half round, laid over and including screed bed or bedding layer of 15 mm thick in CM (1:4), complete all as specified and as directed.

Demolition of stone slabs and tiles of any description and providing Material and labour for providing, exterior grade, coloured glossy finish rubber pressed, cement concrete designer chequered tiles of size 30cm x 30cm x 25mm thick set, jointed and pointed in neat cement slurry with grey cement and pigment to match the shade / colour / matrix of tiles as in floor, over and including cement screed bed of 20 mm thick in CM 1:4. complete all as specified and as directed

Demolishing paver block tiles, and providing material and labour for, Rubber moulded pressed precast concrete interlocking paver block of any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade with grey cement and no pigments, laid over and including 50 mm thick sand cushioning complete all as specified and as directed.

Material and labour for, Rubber moulded pre-cast Kerb stones of cement concrete 1:2:4 (20 mm graded stone aggregates) factory made, size, shape, pattern and finished as approved, including rounding, chamfered or half round and bedded of perfectly leveled surface pointed and jointed in CM 1:4 etc complete all as specified and as directed

Material and labour for Plain cement concrete, 100 mm thick, type D- 2, 1:4:8 (40mm graded aggregate) as in sub base of flooring, flooring etc complete all as specified and as directed

Material and labour for Plain cement concrete type C-1, 1:3:6 ( using 20 mm graded crushed stone aggregate ) 75mm thick as in plinth protection, laid in alternate bays (not exceeding 2 Sq m each) finished the concrete surface even and smooth at top without using extra cement and providing joints throughout the thickness of plinth protection, filled with mastic filling comprising one part of bitumen 85/25 grade and three parts of sand by weight all as specified and directed.

Material and labour for, rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6 finished plastered surface even and smooth without using extra cement complete all as specified and as directed

Material and labour for, rendering 15 mm thick on other than fair faces of brick work or concrete surfaces in cement mortar 1:4 with WPC, finished plastered surface even and smooth without using extra cement complete all as specified and as directed. Note :- Supply only WPC will be measured and paid separately

Supply only water proofing liquid complete all as specified and as directed

Material and labour for, rendering 5 mm thick on ceiling / RCC surfaces in cement mortar 1:3, finished plastered surface even and smooth without using extra cement complete all as specified and as directed.

Preparation of newly plastered surfaces and applying two coats of oil bound distemper over a coat of alkali resistant primer over and including 1 mm thick wall care putty, complete all as specified and as directed. Note : Quoted rate shall deemed to include for cost of wall care putty.

Preparation of newly plastered surfaces of wall and applying two coats of cement base paint complete all as specified and as directed.

Preparing newly plastered ceiling surfaces and applying three coat of white wash complete all as specified & as directed.

Taking down old sinks and Supply and fixing Stainless steel sink with draining board, made out of 1.00 mm thick sheet for kitchen over all size 915 mm x 460 mm with bowl size 405 x 355 x 178 mm all as per Cat No.SSSBSD-52 of Blue Star make or techno commercially equivalent in other makes specified including CP waste coupling of 40 mm dia, cast iron cantilever brackets, 40 mm dia 800 mm long corrugated PVC waste pipe, washers, connecting union etc including bedding in cement mortar on to dwarf wall or fixing on granite slab. complete all as specified and directed.

Taking down old sinks and Supply and fixing Stainless steel sink without draining board, made out of 1.00 mm thick sheet for kitchen over all size 495mm x 420mm with bowl size 405 x 355 x 178 mm all as per Cat No.SSSB06A of Blue Star make or techno commercially equivalent in other makes specified including CP waste coupling of 40 mm dia, cast iron cantilever brackets, 40 mm dia 800 mm long corrugated PVC waste pipe, washers, connecting union etc in cement mortar on to dwarf wall or fixing on granite slab. complete all as specified and directed.

Taking down unserviceable plate rack, supply and fix new Stainless steel plate rack of 0.63mm thick sheet, size 600mm x 750mm and of weight not less than 4.5kg each complete all as specified and directed. Make: Blue star, Model No. SSKPR-311.or techno-commercially equivalent make specified here-in-after.

Supply and fix in repairs, Vitreous china snow white, wash hand basin of size 550 mm x 400 mm excluding chain and plug and porcelain stopper including brackets, supply and fixing of 32 mm dia, PVC corrugated / flexible waste pipe, 800 mm long and with brass waste coupling of 32 mm dia, complete all as specified and as directed. Make : CERA, Cat No S2040103 or techno commercial equivalent in other makes, complete all as specified and as directed.

Supply and fix in repairs, Vitreous china, white colour, water closet pan (pedestal pattern), with PP soft seat cover, hinges, other fixing accessories set (excluding flushing cistern and flush pipe), PVC (SWR), 'P' or 'S' trap, and connecting to drain (or outgoing pipe), flush pipe, anti syphonic pipes and removing debris outside MD land. Make : Cat Part No S1050101 of Cera or techno commercial equivalent in other makes complete all as specified and as directed.

Supply and fix in repairs, Vitreous china, white colour, 'Orissa pattern' squatting pan of size 580 mm x 440 mm with PVC 'P' trap or 'S" Trap, front or back inlet, integral foot rests, connecting to trap, flushing pipe, anti syphonic pipe, including making good to floor removing debris outside MD land, complete, all as per Make : Cera, Cat No S3010102 of CALINA make or techno commercially equivalent in other makes specified here-in-after.

Supply and fix in repairs, PVC valve less, syphonic action type, flushing cistern, Duo Flush cistern 10 litre capacity, low level, white, with inlet, ball valve, 32 mm dia flush pipe, float and handle including brackets, connections to pipes and fixing of chain and pull, or lever, complete all as specified and directed. (Cat No-502 of Prayag or equivalent in any approved make as in CA)

Taking down unserviceable GI tubing, supply and fixing new CPVC pipes, outer dia 20 mm, SDR 11 Plain with all fittings, such as Tee, elbows, sockets, unions, short pieces and application of bituminous paint in concealed portion, fixed to wall/ ceiling or laid on floors, complete all as specified and as directed. Notes: Serviceable Taps, valves in any shall be removed before taking down pipe and same shall be re-fixed while providing new pipe.

All as per Serial Item No 82 here-in-above, but of outer dia 25 mm dia

Taking down unserviceable GI tubing, supply and fixing new 20 mm bore Galvanized Iron tubing, medium grade, with all fittings, such as Tee, elbows, sockets, unions, short pieces and application of bituminous paint in concealed portion, fixed to wall/ ceiling or laid on floors, complete all as specified and as directed. Notes: Serviceable Taps, valves in any shall be removed before taking down pipe and same shall be re-fixed while providing new pipe.

All as per Serial Item No 84 here-in-above, but of outer dia 25 mm dia

Supply and fix in repairs, Brass CP wall mixer for mixing hot and cold water screwed down for iron pipe, with provision for overhead shower, fixed complete all as specified and directed (Cat No-PIS-75H of Neptune series of Prayag or equivalent make as specified here-in-after)

Supply and fix in repairs, 15 mm Centre hole Basin mixture W/o Pop Up all as specified and as directed.(Cat No PIS-50 H Neptune series of Prayag or equivalent make as specified here-in-after.

Supply and fix in repairs, 15 mm pillar taps swan neck type, chromium plated cast copper alloy fancy type complete all as specified and as directed.(Cat No PIS-14H Neptune series of Prayag or equivalent make as specified here-in-after)

Supply and fix in repairs, 100mm (4") overhead shower ABS with brass Arm (225mm) & flange including fixing to steel pipe or union complete all as specified and as directed. (Cat No BS-73 Neptune series of Prayag or equivalent make as specified here-in-after).

Supply and fix in repairs, 15 mm angle cock CP cast copper alloy screwed down high pressure with capstan head handle screwed both ends or for unions etc . (Cat No PIS-10H Neptune series of Prayag or equivalent make as specified here-in-after)

Supply and fix in repairs, Bib Cock 2-way double handle with CP flange all as specified and as directed. (Cat No-PIS-12H Neptune series of Prayag or equivalent make as specified here-in-after).

Supply and fix in repairs, Chromium plated long body bib tap 15mm dia with CP flange all as specified and as directed. (Cat No-PIS-08H Neptune series of Prayag or equivalent make as specified here-in-after).

Supply and fix in repairs, Chromium plated bib tap 15mm dia with CP flange all as specified and as directed. (Cat No-PIS-06H Neptune series of Prayag or equivalent make as specified here-in-after).

Supply and fix in repairs, Health faucet, brass body with 1mtr SS braided tube & wall hook complete all as specified and as directed (Cat No-BEA-41/BEA-85 of Prayag or equivalent make as specified here-in-after)

Supply and fix in repairs, Towel rail stainless steel glossy finish 20 mm dia and 600 mm long complete all as specified and as directed. (Cat No-BA10S of prayag or equivalent make as specified here-in-after)

Supply and fix in repairs, Towel rack Brass glossy finish complete all as specified and directed (Cat No BA-03 of Prayag or equivalent make as specified here-in-after)

Supply and fix in repairs Towel ring Brass glossy finish complete all as specified and directed (Cat No BA-02 of Prayag or equivalent make as specified here-in-after)

Supply and fix in repairs Soap dish chromium plated brass all as per Cat Part No BA-45 of Prayag or equivalent makes fixed in wall as per manufacturers instruction.

Supply and fix in repairs Mirror 600x450 x 5-6mm thick with frame cat No BLM-01F of PRAYAG or equivalent make complete all as specified and directed

Supply and fix in repairs PVC Mirror cabinet of size 400x500 mm (Cat No 554 of Prayag or equivalent make) complete all as specified and as directed.

Supply and fix in repairs Unbreakable (Square) wall mounted shelf 500mm (Cat No BEA-47A of Prayag or equivalent make as specified here-in-after) complete all as specified and directed

Supply and fix in repairs Unbreakable corner shelf (3Pcs set i.e., 8"-1, 10"-1 & 12"-1) (Cat No BEA-44A of Prayag or equivalent make as specified here-in-after) complete all as specified and directed

Supply and fix in repairs peg set of six (Cat No BEA 30 of Prayag or equivalent make of CA) fixed in wall as per manufacturers instruction

Supply and fix in repairs Toilet paper holder (Cat No BA-88 of Prayag or equivalent make of CA) fixed in wall as per manufacturers instructions all as specified and as directed.

Supply and fix in repairs PVC connection (Suitable for Cold Water Supply) 15 mm size with PTMT nuts of length 450 mm, all as specified and as directed.

Supply and fix in repairs PVC connection (Suitable for HOT Water Supply) 15 mm size with PTMT nuts of length 450 mm, all as specified and as directed.

Supply and fix in repairs, 32 mm dia waste fittings, brass, chromium plated for sinks, basins, etc with long screwed shanks and fly nuts, flange end complete all as specified and as directed

Supply and fix in repairs, 75 mm dia waste fittings, brass, chromium plated for sinks etc with long screwed shanks and fly nuts, flange end fixed in repair complete all as specified and as directed.

Supply and fix in repairs, 32mm dia, 800mm long PVC corrugated waste pipe complete all as specified and as directed.

Supply and fix in repairs PVC urinal waste pipe 32mm dia 800mm long, complete all as specified and directed

Dismantling of unserviceable multi floor trap, supply and fix PVC(SWR) multi floor trap 75 mm dia outlet with CP grating, including jointing with solvent cement complete all as specified and as directed.

Supply and fix in repairs grating doom 100 mm dia of PTMT (Minimum weight 25 grams) complete all as specified and as directed

Supply and fix in repairs Health faucet, PVC body, 1.5 m long as per Cat Part No 188 of Prayag or techno commercial equivalent makes specified here-in-after complete all as specified and directed.

Supply and fix in repairs 15mm dia Bib tap (Minimum weight 15mm-120gms), long body, PTMT fancy type any colour screwed, for iron pipe and fixed complete all as specified and as directed.

Supply and fix in repairs 15mm dia Pillar tap PTMT fancy type (Minimum weight 15mm-120gms), any colour screwed, for iron pipe and fixed complete all as specified and as directed

Supply and fix in repairs 15mm dia angle stop valve of PTMT (Minimum weight 15mm-90gms), any colour pressed screwed, for iron pipe and fixed complete all as specified and as directed

Supply and fix in repairs, PVC water tank covers suitable for water tanks of capacity 500 / 1000 / 2000 litres complete all as specified and as directed

Supply and fixing in repairs, EWC seat covers, white closed pattern with recessed bottom, including screws and connectors complete all as per Cat Part No B1510101 of CERA Make or equivalent in other makes, removing debris outside MD land, complete all as specified and directed.

Carrying out Petty repairs to arrest leaking of water in bib taps, pillar taps, stop cock, angle valve, PVC connection waste pipes, float valves, concealed stop cock. GI pipe joints bottle traps etc of any description by changing the washers or any other minor accessories to make the system functional complete all as specified and directed.

Carrying out Petty repairs to high/low level flushing cistern by adjusting the float valve, leakage of PVC connection, PVC/GI bend replacing of rubber washer check nuts plugs etc for any type of flushing cistern complete all as specified and directed.

Disconnecting existing PVC water tank of capacity exceeding 300 litres, but not exceeding 1000 litres (fixed on roof), setting aside (or lowering if required), cleaning, removing all scales, dirt from tanks, from mouths of circulating pipes, etc., and hoisting / re-fixing / re-connecting in same / new position, writing date of cleaning with white paint, (height / size of letters / figures not less than 10 cm in height, re-fixing serviceable ball valve, complete all as specified and as directed.

Dismantling of water tanks of 500 litres capacity from roof top and supply and fixing Rotational moulded polyethylene water storage tanks (double layered) of 500 Litres capacity with ISI mark embossed on it, (cylindrical, vertical with closed top) hoisted and fixed in position complete all as specified and as directed.

All as per Serial Item No 122 here-in-above, disconnecting water tank of capacity 500 litres and setting aside for carrying out repairs and re-fixing disconnected tank.

Dismantling of water tanks of 1000 litres capacity from roof top and supply and fixing Rotational moulded polyethylene water storage tanks (double layered) of 1000 Litres capacity with ISI mark embossed on it, (cylindrical, vertical with closed top) hoisted and fixed in position complete all as specified and as directed.

All as per Serial Item No 124 here-in-above, disconnecting water tank of capacity 1000 litres and setting aside for carrying out repairs and but re-fixing disconnected tank after carrying out repair works.

Supply and fix in repairs, 20 mm dia Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed. (Minimum weight 210 grams) complete all as specified and as directed.

Supply and fix in repairs, 25 mm dia Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed. (Minimum weight 455 grams) complete all as specified and as directed.

Supply and fix in repairs, gun metal, globe or gate valves 20 mm bore (ISI marked) with iron wheel head screwed both ends for iron pipe complete all as specified and as directed.

Supply and fix in repairs, gun metal, globe or gate valves 25 mm bore (ISI marked) with iron wheel head screwed both ends for iron pipe complete all as specified and as directed.

Material and labour for cleaning of PVC/RCC over head water tanks at any height (on accessible/inaccessible roofs) by removing all scale, dirt, mud, any foreign material, accumulated silt, other dirty substance, algae, fungus and any other bacterial material from sides/bottom of tank, cleaning shall be done by draining / pumping out water / sludge from bottom, by high pressure water jet of pressure not less than 120 PSI for removing clogged mud/scales etc and cleaning the same again with self priming pumped fresh water and disinfecting the water tank by using UV radiator and approved chemical (chlorite), after cleaning writing letter / figures (Date of cleaning and next Date of cleaning) on black back ground with white synthetic enamel paint including removing the existing letters/ figures complete all as specified and as directed for water tanks of capacity exceeding 250 litres and not exceeding 500 litres complete all as specified and as directed.

All as per Serial Item No 130, but for water tanks of capacity exceeding 500 litre and not exceeding 1000 litre.

All as per Serial Item No 130, but for water tanks of capacity exceeding 1000 litre and not exceeding 2000 litre. Note for Sl Item Nos 129 to 131 :: (i) Contractor shall ensure that no damages / leakage occur in tank after cleaning . (ii) Any air lock /blockage of water flow after cleaning will be made good immediately.

Material and labour for spraying anti weed / non toxic solution / chemicals containing Glyphosate as per manufacture instructions and removing the weed including the roots after ensuring complete de-germification of plant/weed and cutting down the plant/trees off from roof/top sides of external walls of bldgs, in chajjas, wall junctions, junctions of GI/CI/AC/PVC pipes and taking out roots entered in wall/slabs, including making good the surface using PCC 1:2:4 type B1 or cement mortar (1:2) or brick work in CM(1:4) plastered with CM(1:4) to match with existing surface and repairing the pipes and joints which was affected by cutting down/taking out process all as specified and as directed for plants / trees located in the buildings up to three storey high, complete all as specified and directed by Engineer-in-charge. NOTE:- Contractor has to execute the work of de-generated plant/weeds as per the prior approval and directions of Engineer-in-charge.

All As per item no 133 here in before but plants located in the buildings of four to eight storey high.

Material and labour for cleaning of Roof at height of (on accessible roof height not exceeding 30RM /inaccessible roofs height not exceeding 10RM) by removing all scale, dirt, mud, any foreign material, accumulated silt, other dirty substance, algae, fungus, leaves etc deposited over slab and making good the disturbed surfaces to match with existing surface and removing the material so obtained out side complete all as specified and directed by Engineer-in-charge. NOTE:- Contractor has to submit the photographic record of work done (before and after the work done duly annoted the Building No/Location) at the time of claiming the payment (RAR/Final Bill). No payment has to be made without submit the photographic records.

Removal of sludge from manholes of any size and depth and burying the sludge in pits with suitable depth & filled by earth and removal of surplus soil including dewatering of water complete all as directed to a place as earmarked by state auth out side the defence land . Note - Dewatering of water or mud will not be paid only sludge removed shall be considered for payment.

Clearing & removal of blockage, of any type in WC, bathroom, kitchen including floor/ nahani traps, soil waste/vent pipes gully trap up to 1st manhole, in any situation by way of cleaning / de-sludging and removing foreign materials to a place as earmarked by state authorities out side the defence land to the entire satisfaction of Engineer-in-charge.

Mechanically pumping out sewage liquid from septic tanks/ manholes of any size and depth and removal the same to distance/place as earmarked by state authorities out side defence land including any type of T & P required etc. dewatering of water complete all as directed.

Taking down eaves gutters, soil / waste / vent pipes / rain water pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., Supply and fix, PVC (SWR) pipes 75mm dia, type B (Conforming to IS 13592), single socketed in any length with solvent cement joints laid under floor or on walls fixed as soil / waste / vent pipes with Stack clamps made out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall complete all as specified and as directed.

All as per Serial Item No 139 here-in-above, but for 110 mm dia pipe.

Supply and fix in repairs, 75mm dia PVC (SWR) Bends, with access door of any radius .

All as per Serial Item No 141 here-in-above, but for 110 mm dia pipe.

Supply and fix in repairs, 75mm dia PVC (SWR) junction single (single T) equal or unequal with access door

All as per Serial Item No 143 here-in-above, but for 110 mm dia pipe.

Supply and fix in repairs, 75 mm dia PVC(SWR) branch piece, single(single Y) equal or un equal with access door.

All as per Serial Item No 145 here-in-above, but for 110 mm dia pipe.

Supply and fix in repairs, 75 mm dia PVC (SWR) branch piece, (double Y) equal or unequal with access door

All as per Serial Item No 147 here-in-above, but for 110 mm dia pipe.

Supply and fix in repairs, 75mm dia PVC (SWR) vent cowl.

All as per Serial Item No 149 here-in-above, but for 110 mm dia pipe.

Taking down carefully aluminium/ copper wiring/power point wiring (light, fan, call bell socket or power circuits), without taking out switches, sockets, regulators, light fittings, etc., complete and making good the disturbed surface of walls, ceiling etc including painting with same colour of the back ground complete all as specified and as directed by Engineer-in-Charge.

Material and labour for Concealed Point Wiring complete with 1.5 Sqmm single core PVC insulated unsheathed cable 1100 volts grade multi stranded with FRLS copper conductor conforming to IS 694 drawn through and including non-metallic rigid PVC conduit medium grade ISI marked including accessories concealed in walls including MS terminal boxes fabricated with 1.6 mm thick MS sheet, covering with laminated sheet top cover 3 mm thick fixed with cadmium plated iron screws for housing normal switches, switch socket outlets, fan regulators etc., including provision of 1.5 Sq mm PVC insulated single core multi stranded copper conductor cable as earth continuity conductor and connecting to common earth dolly, all as specified and as directed for light point controlled by one switch / fan point controlled by one switch / regulator / one bell / buzzer point controlled by one bell push

All as per Serial Item No 152 here-in-above, but for one light point controlled by 2 way switch

All as per Serial Item No 152 here-in-above, but for one 3 pin socket outlet 5 Amps on independent board.

All as per Serial Item No 152 here-in-above, but for one 3 pin socket outlet 5 Amps on Same Board.

All as per Serial Item No 152 here-in-above, but wires drawn through existing conduits for light point controlled by one switch / fan point controlled by one switch / regulator / one bell / buzzer point controlled by one bell push.

All as per Serial Item No 152 here-in-above, but wires drawn through existing conduits but for one light point controlled by 2 way switch

All as per Serial Item No 152 here-in-above, but wires drawn through existing conduits for one 3 pin socket outlet 5 Amps on independent board.

All as per Serial Item No 152 here-in-above, but wires drawn through existing conduits for one 3 pin socket outlet 5 Amps on Same Board.

Material and labour for Concealed Point Wiring complete with 1.5 Sqmm single core PVC insulated unsheathed cable 1100 volts grade multi stranded with FRLS copper conductor conforming to IS 694 drawn through and including non-metallic rigid PVC conduit medium grade ISI marked including accessories concealed in walls including MS terminal boxes fabricated with 1.6 mm thick MS sheet, covering with laminated sheet top cover 3 mm thick fixed with cadmium plated iron screws for housing modular switches, switch socket outlets, fan regulators etc., including provision of 1.5 Sq mm PVC insulated single core multi stranded copper conductor cable as earth continuity conductor and connecting to common earth dolly, all as specified and as directed for One light point controlled by one switch / One fan point controlled by one switch/regulator / one bell/buzzer point controlled by bell push

All as per Serial Item No 160 here-in-above, but for one light point controlled by 2 way switch

All as per Serial Item No 160 here-in-above, but for one 3 pin socket outlet 5 Amps on independent board.

All as per Serial Item No 160 here-in-above, but for one 3 pin socket outlet 5 Amps on Same Board.

Material and labour for Point Wiring complete with 1.5 Sq mm single core PVC insulated unsheathed cable 1100 volts grade multi stranded with FRLS copper conductor conforming to IS 694 drawn through and including PVC Casing & Caping ISI marked including accessories surface type wiring including 1.6 mm thick MS sunken boxes concealed on walls including laminated sheet top cover 3 mm thick fixed with cadmium plated iron screws for housing the switches, switch socket outlets, fan regulators etc., including provision of 1.5 Sq mm PVC insulated single core multi stranded copper conductor cable as earth continuity conductor and connecting to common earth dolly, all as specified and as directed for One light point controlled by one switch / One fan point controlled by one switch/regulator / one bell/buzzer point controlled by bell push

All as per Serial Item No 164 here-in-above, but for one light point controlled by 2 way switch

All as per Serial Item No 164 here-in-above, but for one 3 pin socket outlet 5 Amps on independent board.

All as per Serial Item No 164 here-in-above, but for one 3 pin socket outlet 5 Amps on Same Board.

All as per Serial Item No 164 here-in-above, but point wiring with 2.5 Sq mm cable and earth continuity conductor of 2.5 Sq mm for power points.

All as per Serial Item No 164 here-in-above, but for Point wiring with 2.5 Sq mm cable and earth continuity conductor of 2.5 Sq mm for power points drawn through existing conduits.

All as per Serial Item No 164 here-in-above, but with 2.5 Sq mm cable and earth continuity conductor of 2.5 Sq mm for power points Notes for Serial Item Nos 152 to 170 :- (i) The earth wire for points in the same circuit can be looped from point to point, (ii) Earth wire shall be taken inside the conduit, (iii) Cost of terminal box shall deemed to be included in the item rate quoted for point wiring, (iv) Cost of cable from DB to any switch/ socket board to be included in point wiring. (v) Cutting chases, grooving, etc., required for taking down / providing concealed wiring shall be measured and paid for separately under respective item.

Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 for concealed conduit wiring, etc., and making good, cutting not exceeding 10 cm girth, all as specified and as directed.

Taking down unserviceable sub main wiring, supply and fixing Sub main wiring using FRLS grade PVC insulated unsheathed, 1100 volts grade, multi stranded copper conductor cable, 2 runs of single core of size 4 Sq mm and one run of earth continuity conductor of size 4 Sq mm to be drawn through and including PVC non metallic rigid conduit complete all as specified and as directed. NOTE: - Two runs of 4 sq.mm cable, one run of 4 sq mm earth wire and PVC conduit shall be measured as one length.

Taking down unserviceable sub main wiring, supply and fixing Sub main wiring using FRLS grade PVC insulated unsheathed, 1100 volts grade, multi stranded copper conductor cable, 2 runs of single core of size 4 Sq mm and one run of earth continuity conductor of size 4 Sq mm to be drawn through existing PVC non metallic rigid conduit complete all as specified and as directed. NOTE: - Two runs of 4 sq.mm cable, one run of 4 sq mm earth wire and PVC conduit shall be measured as one length.

Taking down unserviceable sub main wiring, supply and fixing Sub main wiring using FRLS grade PVC insulated unsheathed, 1100 volts grade, multi stranded copper conductor cable, 2 runs of single core of size 6 Sq mm and one run of earth continuity conductor of size 6 Sq mm to be drawn through and including PVC non metallic rigid conduit complete all as specified and as directed. NOTE: - Two runs of 6 sq.mm cable, one run of 6 sq mm earth wire and PVC conduit shall be measured as one length.

Taking down unserviceable sub main wiring, supply and fixing Sub main wiring using FRLS grade PVC insulated unsheathed, 1100 volts grade, multi stranded copper conductor cable, 2 runs of single core of size 2.5 Sq mm and one run of earth continuity conductor of size 2.5 Sq mm to be drawn through and including PVC non metallic rigid conduit complete all as specified and as directed. NOTE: - Two runs of 2.5 sq.mm cable, one run of 2.5 sq mm earth wire and PVC conduit shall be measured as one length.

Supply and fix in repairs, Modular Switch, One module, One way, 6 Amps, 240 Volts all as specified and as directed.

Supply and fix in repairs, Modular Switch, One module, One way, 16 Amps, 240 Volts all as specified and as directed.

Supply and fix in repairs, Modular Switch, One module, bell push, 6 Amps, 240 Volts all as specified and as directed.

Supply and fix in repairs, Modular Switch, One module, two way, 6 Amps, 240 Volts all as specified and as directed.

Supply and fix in repairs, Modular socket, 6 Amps, 5 pin combined, 2 module, 240 Volts all as specified and as directed.

Supply and fix in repairs, Modular socket outlet, 2 Module, 6 pin, 6/16 Amps (multi purpose), complete all as specified and directed.

Supply and fix in repairs, Modular fan Regulator,120 W, electronic stepped type, 230 Volts 2 module, complete all as specified and as directed.

Supply and fix in repairs, piano Switch, flush type, One way, SP, 6 Amps, 240 Volts all as specified and as directed.

Supply and fix in repairs, piano Switch, flush type, two way, SP, 6 Amps, 240 Volts all as specified and as directed.

Supply and fix in repairs, flush type, bell push, SP, 5/6 Amps, 240 Volts all as specified and as directed.

Supply and fix in repairs, switch socket combination 5 pin, 2 in 1, 5 Amps, flush type, 240 Volts all as specified and as directed.

Supply and fix in repairs, switch socket combination 3 pin, 2 in 1, 5 & 15 Amps, flush type, 240 Volts all as specified and as directed.

Supply and fix in repairs, flush type socket outlet, 2 in 1, 3 pin 5 Amps, 240 V, complete all as specified and directed.

Supply and fix in repairs, lamp holder, pin type, pvc/polycarbonate made, complete all as specified and as directed by Engineer-in-charge.

Supply and fix in repairs, 09/10 watt LED lamp suitable to fit in angle holder.

Supply and fix in repairs, fan Regulator, 120 W, electronic stepped type, 230 Volts, complete all as specified and as directed.

Supply and fix in repairs, Ding Dong bell, SP, AC, 230 Volts, complete all as specified and as directed.

Supply and fix in repairs, Ceiling rose surface type, Bakelite, 65 x 50 mm ISI marked with three terminals all as specified and as directed.

Supply and fix in repairs, MCB SP, 240 volts, 6 to 32 Amps, 50 Hz, 10 KA breaking capacity, 'C' Series, using copper lugs for terminations, complete all as specified and as directed.

Supply and fix in repairs, MCB SPN, 240 volts, 32 to 40 Amps, 50 Hz, 10 KA breaking capacity, 'C' Series, using copper lugs for terminations, complete all as specified and as directed.

Supply and fix in repairs, MCB TPN, 415 volts, 63 Amps, 50 Hz, 10 KA breaking capacity, 'C' Series, using copper lugs for terminations, complete all as specified and as directed.

Supply and fix in repairs, MCB TPN, 415 volts, 100 Amps, 50 Hz, 10 KA breaking capacity, 'C' Series, using copper lugs for terminations, complete all as specified and as directed.

Taking down unserviceable sheet metal enclosure/ DB, supply and fix, MCB DB SPN 4 way (Horizontal), double door with Sheet metal enclosure, flush mounted, prewired, 240 V, AC, 50 Hz, Factory made, powder coated, IP-42 protection conforming to IS-13032 universal mounting with 200 Amps rated copper bus bar, neutral link, earth link, earthing studs, detachable gland plates with knockouts on both sides, etc complete all as specified and as directed. Notes : i) All unused modules shall be provided with blanking plate for which the cost is deemed to be included in the cost of MCB DBs. ii) MCB/ Isolators will be measured and paid separately as supply and fix under respective items.

All as per Serial Item No 198 here-in-above, but SPN 8 ways

All as per Serial Item No 198 here-in-above, but TPN 4 ways, 415 V

Supply and fixing in repairs, wall mounted LED batten, energy efficient, 20 Watt, 4 feet, with high lumen output of 2000 lumens and diffuser should be High translucent serrated milky white, environmental friendly, energy efficient LED, with accessories, IP 20 protection Class I, system electrical efficiency > 85%, system efficacy > =100 lm/W, operating voltage between 140 - 270 V, AC, 50 Hz, TDH <20%, power factor ≥ 0.90, surge protection 2.5 kV, colour temperature 5700 K, CRI > 80 & integrated electronic driver 20 W fitting prewired and connecting with 3 Core, 1 sq mm sheathed copper flexible cable complete in all respects all a directed by Engineer-in-charge. Cat Part No BCLAB 20WH LED P of Bajaj or techno commercially equivalent makes specified here-in-after complete all as specified.

All as per Serial Item No 201 here-in-above, but of 9/10 W LED tube light fitting 2 feet long and polycarbonate housing. Cat Part No BCLSB 10WH of Bajaj or techno commercially equivalent makes specified here-in-after complete all as specified.

Supply and fix in repairs, bulkhead LED luminaries 10W energy efficient solution for upgrading conventional light fittings, with IP 65 protection, Make: Bajaj, Cat No : BIBWP10WLED or techno commercially equivalent makes specified here-in-after complete all as specified.

Supply and fixing LED ceiling mounted recessed full lit luminaire with glare free uniform illumination 36 W 2 feet x 2 feet (>100 Lumen/Watt), CRCA body, illumination suitable for ceiling, operating voltage between 140 - 270 V, AC, 50 Hz, PF >= 0.95, THD<10%, CCT 5700K, CRI >= 80 and Driver Should be Constant Current LED Driver with 2.5 KV Surge, Driver Efficiency >85%, Driver having High Voltage, Short Circuit Protection and Driver Should be with BIS Certified with R number, integral drivers, prewired and connecting with 3 Core 1 sq mm sheathed copper flexible cable complete in all respects all a directed by Engineer-in-charge. Cat Part No. BZRSQL 36W GZI WH of Bajaj or techno commercially equivalent makes specified here-in-after complete all as specified.

Supply and fixing LED ceiling mounted recessed full lit luminaire with glare free uniform illumination 24 W, 1 feet x 1 feet (>100 Lumen/Watt), CRCA body, illumination suitable for ceiling, operating voltage between 140 - 270 V, AC, 50 Hz, PF >= 0.95, THD<10%, CCT 5700K, CRI >= 80 and Driver Should be Constant Current LED Driver with 2.5 KV Surge, Driver Efficiency >85%, Driver having High Voltage, Short Circuit Protection and Driver Should be with BIS Certified with R number, integral drivers, prewired and connecting with 3 Core 1 sq mm sheathed copper flexible cable complete in all respects all a directed by Engineer-in-charge. Cat Part No. BZSSQL 24W LED WHI of Bajaj or techno commercially equivalent makes specified here-in-after complete all as specified.

Taking down existing security light fitting, Supply and fix 30 W, LED security light fittings with lamp 30 W with high lumen output, environmental friendly, energy efficient LED, with pressure die cast housing with toughened glass and high power LEDs with secondary optics, with lamps and accessories, IP 66 protection, system electrical efficiency > 85%, system efficacy > 110 IP/W, 10 KV SPD, operating voltage between 140 - 270 V, AC, 50 Hz, TDH, 10%, power factor ≥ 0.95, surge protection 2.5 kV, colour temperature 5700 K, CRI > 80, integral drivers, connecting to loop boxes electrically, light fitting conforming to Cat No ENXT P 30 L WH SY PC SD of Bajaj or techno commercially equivalent approved model complete with all accessories and lamp complete all specified and as directed.

Taking down existing brackets, providing Material and labour, for bracket made of Galvanized iron pipe 25 mm dia, light grade, bend to shape not less than 1.2 metre with 2 Nos of MS clamps fabricated out of MS Flats of size 25 x 6 mm, bolts, nuts of suitable size for fixing street light fittings, including 2 coats of aluminium paint complete all as specified and as directed.

Taking down unserviceable ceiling fan, Supply and fix new Ceiling fan BEE 5 star rated, 1200mm sweep, energy efficient suitable to function on 230V, single phase, AC supply, complete with provision for clamps for hanging of ceiling fan and accessories, writing MES No and depositing the unserviceable fan AGE EM Store yard, complete all as specified and directed.

Taking down unserviceable exhaust fan, Supply and fix new Exhaust fan with louvers, 250 / 280 / 300 mm sweep, energy efficient suitable to function on 230V, single phase, AC supply, including provision of 3 core flexible copper wire, 24/ 0.20 sq mm, writing MES No and depositing the unserviceable fan in AGE EM Store yard, complete all as specified and directed. Cat Part No 70079 MAXX AIR of Bajaj or techno commercial makes approved here-in-after.

Taking down unserviceable fresh air fan, Supply and fix new fresh air fans with louvers, 150 mm sweep, 1200 / 1400 RPM energy efficient suitable to function on 230V, single phase, AC supply, including provision of 3 core flexible copper wire, 24/ 0.20 sq mm, writing MES No and depositing the unserviceable fan in AGE EM Store yard, complete all as specified and directed.

Supply and fix in repairs, sheet metal enclosure, SPN, with metal plug and socket, 20 Amps, 240 Volts, complete all as specified and as directed.

Taking down unserviceable, storage water heaters depositing same in AGE E/M Storeyard, Supply, installation, testing and commissioning of vertical type electric storage water heater of capacity 25 litre, BEE five star rated, 230 Volt, AC, 50Hz, comprising of heating element 2000/2500 Watt, puf insulation, both power indicating LED lamp and heating indicating LED lamp, actual standing energy loss per 24 hours / 45°C temperature difference not to exceed 0.5KWH, re-heating time for 35°C temperature rise not to exceed 20 minute, adjustable thermostat (temperature range in °C is 25-75±5), rated water pressure (N/sq.cm, water head (metre)) is 80/80, glass lined tank, glass coated heating element (to prevent water scale formation on element), temperature control knob, anode ord (to protect tank from corossive element), thermal cutout, safety valve (the safety valve shall be designed to automatically relieve pressure and discharge water in case the pressure overshoots the preset limits), with and including provision of necessary suitable 3-core copper cable, suitable plug top, , fixing of geyser on wall / surface with and including provison of suitable size of wall mouting bracket and 100mm length anchor bolts, including provision of all necessary plumbing work, civil works etc., complete all as specified and directed.

Taking down, inspecting, dismantling of geysers of any type/capacity, cleaning, descaling, carrying out hydraulic pressure test of container with hand operated hydraulic pump, brazing inner tank, internal wiring and re-installation in old position after replacing of unserviceable parts all as specified & as directed. Note : Supply of parts shall be measured & paid separately.

Supply only stainless/Mild steel inner tank of capacity 25 ltrs unit including internally assembly of any size and type complete all as specified & as directed.

Supply only internal assembly / apparatus rod unit of any size and type suitable for 25 ltrs capacity Geyser all as specified & as directed.

Supply only heating element of 2 KW rating triangular/ round type as per existing size and type including rubber washers all as specified & as directed.

Supply only heating element of 2 KW rating Hexagonal spiral/bend type as per existing size and type including rubber washers all as specified & as directed.

Supply only Thermostat / auto cut-off of suitable size and type for 25/50 Ltrs capacity of any size.

Supply only Indicator lamp red and green type square/round.

Supply only Safety valve/high pressure valve / NRV of exisitng type ISI marked.

Supply only PVC insulated Copper cable flexible 3 core of size 40/0.0076 ISI marked.

Supply only outer cover of geyger of 25 ltrs capacity, complete with all fitting and fixtures as specified & as directed.

Supply only PVC flexible pipe 16mm dia 450mm long with 2 Nos of brass ferrule & rubber washer for hot and cold water all as specified & as directed. (Set of 2)

Preparation of old painted surfaces of geyser, cleaning & applying one coat of spray paint of white enamel, writing MES No, incluing taking down and refixing in same or other place complete all as specified & as directed by Engr -in-Charge.

Disconnecting electric connection / lines, Taking down ceiling fan of 1200mm/1400mm sweep / wall mounted fan 300/450 mm sweep from position, preparing the surfaces, cleaning all dust, filling cavities with filler, spray painting with one coat of synthetic enamel paint, writing MES No, replacing the split pin, rubber pulley, etc., and re-fixing the same complete all as specified and as directed.

Disconnecting electric connecting and dismantling of ceiling fan/exhaust/wall mounted fan of any type/size, inspectin for any defects, cleaning, applying oil and grease, bearing, tightening of nuts and bolts and refixing on old place, complete after carrying out necessary repairs / replacement of Unserviceable parts all as specified & as directed. Note : Supply of parts shall be measured & paid separately.

Supply only ball bearing of various sizes / make as required for ceiling fans/wall mounting / exhaust fan, including greasing, complete all as specified and as directed.

Supply only Gun metal bush of any size/make suitable for ceiling fans all as specified and as directed.

Supply only capacitor of 2.5 Mfd, suitable for ceiling / exhaust /wall mounting fans complete all as specified and as directed.

Supply only capacitor 4.0 Mfd suitable for ceiling / exhaust/wall mounting fans complete all as specified and as directed.

Supply only, PVC flexible cable twin twisted core of 23/0.0076 size multi stranded copper conductor, suitable for connecting ceiling fans / exhaust /wall mounting fans complete all as specified and as directed.

Supply only, rubber bush with MS bolts, nuts & washers with 'U' clamps for ceiling fans complete all as specified and as directed.

Dismantling / opening ceiling fan of 1200 mm sweep of any make and type, removing old defective winding carefully, cleaning the inner parts and rewinding with super enamelled copper conductor of same gauge, maintain good insulation, varnishing, drying and reassembling / re-fixing in its position complete all as specified and as directed.

Dismantling /opening the ceiling fan of 1400 mm sweep of any make and type, removing the old defective winding carefully, cleaning the inner parts and rewinding with the same gauge supper enamelled copper conductor of good insulation, varnishing, drying and reassembling complete all as specified and as directed.

Dismantling /opening wall mounted fan of 300 mm sweep of any make and type, removing old defective winding carefully, cleaning the inner parts and rewinding with the same gauge super enamelled copper conductor of good insulation, varnishing, drying and re-assembling complete all as specified and as directed.

Taking down exhaust fans 230 mm/300mm / 450mm sweep from position by duly disconnecting electric lines, preparing the surfaces, filling cavities with filler, after cleaning all dust, spray painting with one finishing coat of synthetic enamel paint including writing MES NO and replacing the split pin, rubber pully etc., including refixing and connecting the same complete all as specified and as directed.

Dismantling /opening the exhaust fan of 230 mm/300 mm sweep of any make and type, removing the old defective winding carefully, cleaning the inner parts and rewinding with the same gauge supper enamelled copper conductor of good insulation, varnishing, drying and reassembling complete all as specified and as directed.

M&L extension of down rod for ceiling fan upto 1.5 mtr including nut, bolts , washers complete accessories all as specified and as directed.

Removing the window type AC/Split type AC of 1.0/1.5/2.0 ton capacity from location servicing the AC, cleaning the condenser and evaporator coil by blower, checking the electrical wiring, repalcement of burnt out wiring terminals, cleaning the air filter, gas charging, adjusting relays etc., replacement of unserviceable spare parts and fixing back at location, testing and commissioning complete all as directed.

Disconnecting, removing split type AC of any make from position transporting to a OEM / OEM authorised workshop, cutting suction and discharge line of unserviceable compressor and replacing with new factory made hermatically sealed compressor of same make and type, connecting suction and discharge lines, vacuuming the entire system, arresting all leakages, charging of required quantity of refrigerant gas, adjusting relays, thermostat, etc bringing back and installing in its original position including testing and commissioning, complete all as directed for 1.5 Ton Capacity :- Note for item No 61 to 62 :- (i) Gas will be measured and paid separately for item No 61 to 62 under relevent item of this schedule. (ii) Spares costing more than ` 200/- will be measured and paid seperately under relevant item.

All as per Serial Item No 240 here-in-above, but for 2 Ton Capacity

Leak detection and arresting leakages of gas for Split / Window ACs, by brazing and flushing the system complete and testing complete after rectification for 1.5 Ton Capacity AC

All as per Seerial Item No 242 here-in-above, but for 2 Ton Capacity

Taking down unserviceable fan blades from condenser motor shaft, supply and fixing new fan blade of same size and type for any capacity of window type AC and water coolers all as specified and directd.

Taking down unserviceable thermostat, supply and fix new thermostat of same make and type for Split/window type AC 1.5/2 ton capacity.

Taking down unserviceable condenser unit & supply & fix new condenser unit & connecting to the discharge line, brazing, vaccumising & gas charging the unit with required quantity of refrigerant for Split/window type AC of 1.5/2 Ton capacity and testing complete all as directed.

Taking down unserviceable running capacitor, Supply and fix new running capacitor of 40 mfd suitable for 1.5 ton AC make :- BHEL / EPCOS/ TDK/ TIBCON or equivalent.

Taking down unserviceable starting capacitor, Supply and fix new starting capacitor of 80 mfd suitable for 2 ton AC make :- BHEL / EPCOS/ TDK/ TIBCON or equivalent.

Taking down unserviceable overload protection and Supply and fix new over load protector for split/window type AC of 1.5/2.0 TR capacity.

Supply and fill refrigrent gas (R-22/410A/134A) for domestic cooling appliance.

Replacing unserviceable sensor/remote unit with new sensor unit suitable for indoor unit of 1.5 T capacity AC of Makes carrier / Bluestar / Voltas

All as per Seerial Item No 251 here-in-above, but for 2 Ton Capacity

Replacing unservicable PCB with new PCB suitable for split AC / window AC of any type and of any make 1.5 Ton capacity all as directed.

All as per Seerial Item No 253 here-in-above, but for 2 Ton Capacity

Disconnecting and taking PCB circuit of disconnecting out PCB from split AC, repairing the same and refixing in original location complete all as specified and directed for 1.5/2 Ton capacity all as directed.

Disconnecting electrical connections, removing copper discharge line of split type AC 2 Ton capacity (indoor and out door units) with all accessories, shifting to new location or re-installing in same location, after carrying out repair works complete all as specified. Note : Cost of making holes and finishing the surfaces matching with adjacent surfaces shall deemed to be included in quoted rate.

Supply and fix in repairs, plastic/coir filter suitable for Split/window type AC 1.5/2 Ton capacity complete all as specified and as directed.

Disconnecting unserviceable voltage stabilizer of Split / window type AC, supply and fix new voltage stabilizer of 1 KVA capactiy, complete all as specified and as directed. Make : V Guard/Everest/ Sinotech

All as per Seerial Item No 258 here-in-above, but of 2/3 KVA Capacity

All as per Seerial Item No 258 here-in-above, but of 5 KVA Capacity

Supply and fix in repair, brass angle valve for gas charging to split AC 1.5/2 ton of AC compete all as specified and as directed.

Supply and fix in repairs of swing motor of existing capacity and type, suitable for indoor unit of split AC fins complete all as specified and as directed

Supply and fix in repairs, MS fabricated clamps for hanging fans including hook as per existing complete all as specified and as directed

Taking down damaged insulaiton, providing Material and labour of Nitrile rubber insulation for suction and dischaged pipe of split type AC of size 15/19 mm dia complete all as specified and as directed.

Supply and fix in repairs Soft copper tubbing 15mm dia with nitrile rubber insulation suitable for split type AC complete all as specified and as directed.

Supply and fix in repairs Soft copper tubbing 19mm dia with nitrile rubber insulation suitable for split type AC complete all as specified and as directed.

Demolishing of existing earth pits, and providing Material and labour for, earthing complete with Galvanized Iron earth plate electrode 600 mm x 600 mm x 6 mm buried directly in ground vertically in pit of depth not less than 2.25 meter below normal ground level with top edge of the earth plate at a depth not less than 1.5 meter below normal ground level surrounded from all sides with mixture of charcoal and common salt in alternate layers and electrode connected to galvanized earth lead wire of 4 mm dia by means of bolts, nuts, check nuts and washers, earth wire protected by galvanized steel pipe 15 mm bore (light grade) connected to machinery/ equipment all as shown in electrical plate No. 3 of SSR-2009 Part I and including necessary excavation and earth work in any type of soil, 40 mm bore light grade GI pipe for watering funnel wire mesh, PCC chamber in CC (1:3:6), type C1 , manhole cover with RCC (1:2:4), type B1, reinforced with 6 mm dia MS round bars @ 15 cm c/c both ways for cover and MS frame etc., complete all as specified and as directed NOTE :- Earth pit shall be constructed at least 0.5 meter away from each earth chamber.

M&L providing cement concrete type B0 1:2:4 (12.50mm graded stone aggregate) in copings, parapets and railing upto 60cm height, levelling concrete for roof slab, kerbs, water troughs and the like including weathering slightly rounded or chamfered angles and throating all as specified and as directed.

Chaitanya Constructions

SP ENTERPRISES