REPAIR MAINTENANCE OF CENTRIFUGAL AND MONOBLOCK PUMP SETS SUBMERSIBLE PUMP SETS AND ELECTRIC CONTROL PANELS OF SUBMERSIBLE DEVELOPMENT OF BOREWELL LT PANELS AND INTERNAL WIRING INCLUDING CONNECTED ITEMS OF WATER SUPLY INSTALLATIONS OF COD AREA 505 AB

Amount

Disconnecting of electric connections from LT control panel and starter of submersible pump set of size 2 to 15 HP ,removing the pipe line connections from discharge side and taking down/out submersible pump set along with column pipe from bore well with the help of chain pully block including transportation to workshop for repairs and back , lowering the pump in bore well after repairs after replacement of rusted nuts, bolts, washers, rubber gasket etc including testing complete all as specified and as directed .

Labour for Opening the submersible pump set for repairing, rewinding and assembling the pump set including insulating material of any size of capacity 2 to 15 HP complete all as specified and as directed by Engg-in-charge.(different make and size of copper winding and other spare parts will be measured under relevant items of this shedule as supply only.) Note :- Copper winding wire of appropriate gauge shall be measured and paid separetely

Supplying and assembling super enamelled copper winding wire of appropriate gauge suitable upto 2 to 15 HP capacity submersible pump set complete all as specified and as directed.

Supply Only following spare parts for submersible pump set of capacity 2 HP to 15 HP.

GM Bush.

Rotor Sleeve.

Water seal and cable seal

Thrust bearing

Revolving Disc

CI Connection piece

GM Sand Guard

Sealing Ring

CI upper Housing

CI lower Housing

Flange upper with stud and nut

Flange lower with stud and nut

Seal bush

CI Motor Base

Thrust plate

Stainless steel coupling

Coupling key

Stud and nuts for connection piece

T Bolt with Nut

LNK Bolt SS

Submersible cable joint

CI Suction Chamber

CI Stage bowl

GM Impeller

EPV Impeller

EPV Stage Bowl

Guide Bush

GM DOWL Bush

SS DOWL Sleeve

Inter ring

CI DOWL Piece

CI NRV body

Impeller key

SS pump shaft per stage

pump sand guard

SS Distance Sleeve

EPV Defuser

Hook bolt with nut

GM Neck Ring

Mild steel stud with nut

Wire mesh

Drain plug

Labour only for Rotor Sleeve turning and grinding

Labour only for Remetling of Rotor, turning and balancing

Labour only for Repairing of stator stamping

Labour only for balancing of rotor

Labour only for Remetling of GM impeller & turning

M & L for Preperation to existing submersible pump set of capacity 2 to 15 HP and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed .

Supply and fixing in replacement GI Nipple with flange welded, heavy duty 50 x 300 mm size complete all as specified and as directed.

All as per serial item No 6.00 here-in-before but of size 80 x 300 mm

Supply Only GI column pipe, heavy grade, class 'C', 50 mm bore of 3 metre length, heavy duty, flange welded on both ends complete all as specified and as directed .

All as per serial item No 8.00 here-in-before but 80 mm bore Note for 8.00 to 9 :- rate quoted for labour required is deemed to be included in item no. 1.

Disconnecting of electric connections from LT control panel and starter of monoblock submersible pump set of size 2 to 10 HP vertical/ Horizontal ,removing the connections from discharge side and taking down/out mono block submersible pump set from well/sump/sewage well/Sewage treated tank with the help of chain pully block including transportation to workshop for repairs and back , lowering the pump in same place after repairs after replacement of rusted nuts, bolts, washers, rubber gasket etc including testing complete all as specified and as directed .

Labour for Opening the mono block submersible pump set for repairing, rewinding and assembling the pump set including insulating material of any size of capacity 2 to 15 HP vertical/ Horizontal complete all as specified and as directed by Engg-in-charge.(different make and size of copper winding and other spare parts will be measured under relevant items of this shedule as supply only.) Note :- Copper winding wire of appropriate gauge shall be measured and paid separetely

Supplying and assembling super enamelled copper winding wire of appropriate gauge suitable for mono block submersible upto 2 to 10 HP complete all as specified and as directed.

Supply Only following spare parts for mono block submersible pump set of capacity 2 HP to 10 HP.

Bearing Bush

Thrust Plate

CI Impeller

Thrust bearing

Impeller key

Impeller Nut

Rubber Gasket

O ring

M Seal

Oil Seal

Cable Kit Jointing

Float Switch

Labour only for Rotor Sleeve turning and grinding

Labour only for balancing of rotor

Supply and fixing in replacement submersible copper cable of size 2.5 Sq mm 3 core, 1100 Volts complete all as specified and as directed .

All as per serial item No 14.00 here-in-before but cable of size 4 Sq mm 3 core , 1100 Volts .

Supply and fixing in replacement Mild steel clamps in Mild steel flat of size 50mm x 6 mm with including two Nos Mild steel nut and bolts suitable for 50mm bore column pipe complete all as specified and as directed.

Supply and fixing in replacement Mild steel clamps in Mild steel flat of size 80 mm x 6 mm with including two Nos Mild steel nut and bolts suitable for 80mm bore column pipe complete all as specified and as directed.

Supply and fixing in replacement M.S. Casing Cover, heavy duty, made out of Mild steel sheet not less than 6mm thick suitable for 200-300 mm bore pipe complete all as specified and as directed .

Supply and fixing in replacement single phase preventor, type VSP-II complete all as specified and as directed.

Supply and fixing in replacement Amp Meter 0 to 100 Amp of size 96 mm x 96 mm, digital type complete all as specified and as directed.

Supply and fixing in replacement Volt meter 0 to 500 Volts of size 96 x 96 mm digital type

Supply and fixing in replacement analog type time switch FM 1/Quartz daily 240 volts, AC, 50 Hz code AUTS01ANA00 complete all as specified and as directed

S&F Star Delta electronic ST 100 Timer 3-30 Second duration, 160 V to 500 V

Supply and fixing in replacement Indicating light RYG LED type (03 Nos each Set) complete all as specified and as directed .

Supply & fixing , install testing and commissioning of feeder pillar box ,outdoor type cubical shape,three phase, 4 wire, Al bus bar for phases and neutral made out of CRCA sheet 3.15 mm thick ,factory fabricated , CPRI approved , powder coated ,dust and vermin proof , provn for ventilation , angle iron frame and four legs of 50x50x6mm thick angle iron ,2 ft long grouted on PCC foundation of height not less than 30 cm from the ground level , grouting properly ,and of suitable size to accomodate the items mentioned below and having seperate compartment /chambers for cable gallery busbar ,switch gear etc all as specified and comprising of following including necessary cable connections to the MCCBs ,voltmeter,Ammeter and cable lugs etc .

Al bus bar with PVC sleeve suitable for 200 amps for phase & 200 Amp for neutral - 01Set.

Phase indicating lamps LED type ( red , yellow, blue) 01 set

Incoming MCCB 125 Amp 3 pole 18 KA with adjustable thermal and fixed magnetic release -01 No

outgoing MCCB 63 Amp 3 pole 18 KA with adjustable thermal and fixed magnetic release -01 No

FASD Stater with ms sheet encloser ML 1.5 FASD-01 Nos

Analog time switch -01 No

Single phase preventer-01 No

Extension/ development of borewell for drilling not less than 250 mm bore hole by DTH method to any depth below the ground level in any kind of rock/soil upto 100 mtr deep including disposal of surplus soil to a distance not exc 50 mtr away complete all as specified and as directed. Note : 1) In case of incountering rock prior to 30 mtr depth from ground level the decission of the Garrison Engineer for reboring shall be final and binding. Specific order in writing shall be issued by Garrison Engineer for reboring and the quantities shal vary accordingly.2) cost of transportation of DTH plant is included in the unit rate.

Supplying, lowering & fixing into bore 200 mm dia MS casing pipe, heavy duty as per IS-4270, minimum 5.4 mm thick ERW having Duly welded both sides socketed ends ciomplete all as specified and as directed.

Supplying, lowering & fixing into bore hole 200 mm dia MS casing pipe, heavy duty as per IS -4270 minimum 5.40 mm thick ERW slotted tube having 1.5 mm to 3mm slot having socketed ends at complete all as specified and as directed

M&L for development of bore well of any capacity and size at the pressure 10 kg/sqcm to 15 kg/sqcm by diesel engine driven air compressor of capacity 620 cfm includiing air pipe and connected items to improve the yield of tube well complete all as specified and as directed.

Supplying and packing pea gravel of size 3.00 mm to 6.00 mm around casing pipe complete all as specified and as directed.

Disconnecting of electrical connections from panel board including disconnecting the cable leads from the motor terminal box and Opening the electric induction motor of following capacity including taking down/out the burnt winding wire , cleaning the slots, rewinding the motor with super enamalled copper winding wire of existing gauge ,weight etc taking down/out from base plate of pump set after opening the nuts, bolts etc and transporting the motor to workshop for repair and back, re-installed after repair including testing complete all as specified and as directed .Note:- Copper winding wire of approprioate guage will be measured in supply only

Disconnecting and De-coupling the Centrifugal pump of following capacity from foundation after opening /cutting the rusted nuts, bolts & Opening the centrifugal pump of following capacity, repairing the same by replacing the unserviceable spare parts including machining work and re-assembling the same in original position complete etc including transporting the pump to workshop for repair and back, re-installed at existing position after repair and providing new MS nuts, bolts,packing flange etc including testing complete all as specified and as directed. Note:- Spare Parts required shall be measured & paid spaerately.

Supply and fixing in replacement of spare parts for Centrifugal pump of 5-15 HP Capacity.

CI Impeller

pump shaft

CI Casing wear ring

CI interstage ring

CI stuffing box bush

CI Gland Plate

lentern ring

eye bolt with nut

CI Shaft sleeve

Gasket Packing Sheet

Gland packing champion (Both side)

impeller key

coupling key

water liquid deflector

CI bearing cartridge

CI bearing plate

MS Stud with nut

Supply and fixing in replacement of spare parts for Centrifugal pump of 20-30 HP Capacity.

CI Impeller

pump shaft SS (AISI-410)

Remetling of pump shaft, turning and balancing

CI Shaft sleeve

CI Casing wear ring

CI interstage ring

CI stuffing box bush

CI Gland Plate

lentern ring

eye bolt with nut

Gasket Packing Sheet

Gland packing champion (Both side)

impeller key

coupling key

water liquid deflector

CI bearing cartridge

CI bearing plate

MS Stud with nut

Supply and fixing in replacement of spare parts for Centrifugal pump of 40-50 HP Capacity.

CI Impeller

pump shaft SS (AISI-410)

Remetling of pump shaft, turning and balancing

CI Shaft sleeve

CI Casing wear ring

CI interstage ring

CI stuffing box bush

CI Gland Plate

lentern ring

eye bolt with nut

Gasket Packing Sheet

Gland packing champion (Both side)

impeller key

coupling key

water liquid deflector

CI bearing cartridge

CI bearing plate

MS Stud with nut

Supply and fixing in replacement of spare parts for Centrifugal pump of 60-75 HP Capacity.

CI Impeller

pump shaft SS (AISI-410)

Remetling of pump shaft, turning and balancing

CI Shaft sleeve

CI Casing wear ring

CI interstage ring

CI stuffing box bush

CI Gland Plate

lentern ring

eye bolt with nut

Gasket Packing Sheet

Gland packing champion (Both side)

impeller key

coupling key

water liquid deflector

CI bearing cartridge

CI bearing plate

MS Stud with nut

Supply and fixing in replacement of spare parts for Centrifugal pump of 90-105 HP Capacity.

CI Impeller

pump shaft SS (AISI-410)

CI Shaft sleeve

CI Casing wear ring

CI interstage ring

CI stuffing box bush

CI Gland Plate

lentern ring

eye bolt with nut

Gasket Packing Sheet

Gland packing champion(Both side)

impeller key

coupling key

water liquid deflector

CI bearing cartridge

CI bearing plate

MS Stud with nut

Supplying and assembling super enamelled copper winding wire of appropriate gauge suitable upto 105 HP.

Supplying and Fixing in replacement of Terminal Connection Plate of following capacity

Supply and fixing spare tyre for coupling type TC/P/011 after taking down/out as existing at site complete all as specified and as directed.

Supply and fixing spare tyre for coupling type TC/P/013 after taking down/out as existing at site complete all as specified and as directed.

Supply and fixing spare tyre for coupling type TC/P/014 after taking down/out as existing at site complete all as specified and as directed

Supply and fixing spare tyre for coupling type TC/P/015 after taking down/out as existing at site complete all as specified and as directed

Supply and fixing spare tyre for coupling type TC/P/019 after taking down/out as existing at site complete all as specified and as directed.

Supply and Fixing in replacement of Ball Bearing 6305

Supply and Fixing in replacement of Ball Bearing 6306

Supply and Fixing in replacement of Ball Bearing 6307

Supply and Fixing in replacement of Ball Bearing 6308

Supply and Fixing in replacement of Ball Bearing 6309

Supply and Fixing in replacement of Ball Bearing 6310

Supply and Fixing in replacement of Ball Bearing 6312

Supply and Fixing in replacement of Ball Bearing 6314

Supply and fixing in replacement 3 pole power contactor type ML-1.5, 415 Volts, 50 HZ range 25 Amps complete all as specified and as directed

Supply and fixing in replacement 3 pole power contactor type ML-2, 32 Amps, 415 Volts, 50 HZ complete all as specified and as directed.

Supply and fixing in replacement 3 pole power contactor type ML-3, 40 Amps, 415 Volts, 50 HZ complete all as specified and as directed

Supply and fixing in replacement 3 pole power contactor type ML-4, 70 Amps, 415 Volts, 50 HZ complete all as specified and as directed

Supply and fixing in replacement 3 pole power contactor type ML-6,110 Amps, 415 Volts, 50 HZ complete all as specified and as directed

Supply and fixing in replacement 3 pole power contactor type ML-12, 200 Amps 415 Volts, 50 HZ complete all as specified and as directed.

S & F in replacement of over load replay type ML 1.5, starter , relay range 10-16 Amp complete all as specified and as directed.

S & F in replacement of over load relay type ML 2, starter , relay range 20-32 Amps complete all as specified and as directed.

S & F in replacement of over load relay type ML 3, starter , relay range 28-42 Amps complete all as specified and as directed.

S & F in replacement of over load relay type MN 5 ,MNX relay range 45-75 Amps complete all as specified and as directed.

S & F in replacement of over load relay type MN 5 ,MNX relay range 66-110 Amps

Material and labour for painting Two coat of synthetic enamel paint as per existing pattern or scheme, on centrifugal pump & motor of any capacity rating 10-105 HP upto NRV or sluice valve,and MS Base channel including preparation of surfaces by scratching and removing the rust complete all as specified and as directed.

Supply and Fixing in replacement MS base channel & angle of size as exists including cutting, welding and making hole including applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed.

Supplying , laying , jointing, welding and testing MS Pipe (Heavy class 'C') IS : 1239/3589, of followiing sizes laid in trenches or in Horizontal/Vertical/inclined position or laying on floors for connections for suction, to header and connected to out going water main CI/DI/GI pipe line, for following size including taking out the old unserviceable pipes :- Note:- MS Flanges incl fabrication work will be measured and paid separately.

80mm dia

100 mm dia

150 mm dia

supply and fixing in replacement of MS flange 80 mm bore ,16mm thick duly welded with flange joint including nuts bolts ,washer ,Rubber or fiber board gasket joint of size 80mm size

supply and fixing in replacement of MS flange 100 mm bore ,16mm thick duly welded with flange joint including nuts bolts ,washer ,Rubber or fiber board gasket joint of size 100mm size

Supply and fixing in replacement of MS flange 150 mm bore ,16mm thick duly welded with flange joint including nuts bolts ,washer ,Rubber or fiber board gasket joint of size 150mm size

Supply and fixing jointing and testing of cast iron Non return valve without by pass arrangment swing type confirming to IS 5312 flanged ends pressure rating PN 1.0 complete including taking out unserviceable NRV all as specified and as directed by Engineer-in-Charge. Note - Flanged joints complete with rubber jointing materail shall deemed to be included in the unit rate of this item

80 mm bore

100 mm bore

150 mm bore

Supply and Fixing in replacement of CI Foot valve of following size , Flanged ends, Swing type opration with rubber sheet as per IS-4038 including taking out unserviceable of following sizes complete all as specified and as directed Note :- Flanged joints comlete with jointing material shall deemed to be included in the unit rate of this items.

80 mm bore

100 mm bore

150 mm bore

Material and labour for PCC (1:2:4) type B-I (with 20 mm graded aggregate) as in coping, grouting, MS nut for motor base , finished even and smooth without using extra cement as on brick work/flooring complete including demilition of PCC complete all as specified and as directed

Supply and Fixing in replacement of MS foundation bolts with nuts and washers, size 20mm dia , 450 mm long complete all as specified and as directed.(including breaking of hard standing foundation)

Supply and Fixing in replacement of Vibration Pad with nuts, bolts and washers, for existing capacity of 7.5-30 HP complete all as specified and as directed

Supply and Fixing in replacement of Vibration Pad with nuts, bolts and washers, for existing capacity of 40-75 HP complete all as specified and as directed.

Supply and fixing in replacement PVC insulated multistranded copper conductor wire of 10 Sqmm size, single core, 1100 volts complete all as specified and as directed.

All as per item no 76 here in before but of size 16 Sqmm

All as per item no 76 here in before but of size 25 Sqmm

All as per item no 76 here in before but of size 35 Sqmm

Excavation in trenches not exc 1.5 metres wide and not exc 1.5 metres deep for pipe lines in soft/loose soil, getting out and levellling of bottom surface to required level complete all as specified and as directed

Returning fillling in including spreding, leveling, watering and well ramming in layers not exc 25 cm thick complete all as specified and as directed

Removing execavated material from site to a distance not exc 50 metres away and depositing where directed not exc 1.5 metres from the starting point complete all as specified and as directed

Supplying and laying well burnt bricks sub class B for protection of cable complete all as specified and as directed

M&L Jamuna Sand filling under and above the electrical cable for cable cushioning complete all as specified and as directed.

S & F in replacement of LT XLPE cable from trenches/wall/ceilings and Supply ,laying jointing and testing LT XLPE under ground cable PVC insulated armoured heavy duty 1100 volts grade sheated 25 sq mm 3.5 core, aluminium conductor including connection to panel at incoming and out going using aluminium lugs complete all as specified and as directed

All as per item No 85 Here in before but 35 Sqmm

M&L Galavanised iron strip 25x4 mm as earthing lead including connecting to earthing test point to the equipment to be earthed by means of nuts ,bult and washers complete all as specified and as directed

M & L for heat shrinkable LT 1100V straight through joint suitabel for aluminium conductor cable of size 25 to 50 sqmm complete all as specified and as directed

S & F Fully automatic stat delta motor starter of maximum motor output 17.5 Hp of motor rating AC 3 duty 415V 50 Hz 3 phase, MN-16, relay range 9-15 Amps including taking down old starter complte complete all as specified and as directed

All as per item no 89 Here in before but 30 HP MN-25, relay range 14-23 Amps

All as per item no 89 Here in before but 50 HP ML-3, relay range 28-42 Amps

All as per item no 89 Here in before but 75 HP ML-4, relay range 45-75 Amps.

S & F in replacement MCCB 600 to 630 Amps, 4 pole 415V ,Adjustable type of breaking capacity 50 KA inlcuding link and connecting to bus bars and cable end termination with suitable lugs complete all as specified and as directed.

All as per item No 93 here in before but MCCB 400Amps, 4 pole, 415 V, breaking capacity 36 KA

All as per item No 93 here in before but MCCB 250Amps, 4 pole, 415 V, breaking capacity 36 KA

All as per item No 93 here in before but MCCB 200Amps, 4 pole, 415 V, breaking capacity 36 KA

All as per item No 93 here in before but MCCB 160, 4 pole, 415 V, breaking capacity 36 KA

All as per item No 93 here in before but 3 pole MCCB 125 Amps,415V, breaking capacity 16 KA

All as per item No 93 here in before but 3 pole MCCB 63 Amps,415 V, breaking capacity 16 KA

Taking down old unserviceable point wiring from existing conduit ( light fan , socket or powder) complete such as switches, ceiling rose, pendent holder and socket etc and removing the material from site and making good the disturbed surface of wall / floor/ ceiling etc complete all as specified and as directed.

Material and labour for point wiring complete with 1.5 Sq mm (nominal area) FRLS PVC insulated un-sheathed and stranded copper conductor cable ISI marked and including PVC concealed conduit ISI marked of size 20 mm dia medium grade and PVC conduit fittings such as tees, bends, elbow, reducers except conduit junction box (junction box will be of MS) including FRLS PVC insulated unsheathed 1.5 Sqmm copper earth wire, connecting to common earth dolly with and incl Metal flush box of suitable size for fixing modular switches/sockets/fan regulator etc complete all as specified and as directed for the following :- (Note : The cost of modular type Metal boxes and modular accessories like cover plates will be included in quoted rate.)

one light point / fan point/ exhaust fan point / circulator fan point / bell/ buzzer controlled by one 1-way switch/ bell push.

one socket outet point 5 amps on the same board.

one socket outet point 5 amps on the independent board.

All as per item no. 101 here in before but with 2.5 sqmm copper FRLS wire with 1.5 Sqmm FRLS copper earth wire

Supply & fixing in replacement of switch piano, flush type single pole 1 way, 5 Amps complete all as specified and as directed.

Supply & fixing in replacement of switch piano, flush type single pole 1 way, 15 Amps complete all as specified and as directed.

Supply & fixing in replacement of socket outlet 6 Amp, 2 in 1,3 pin 5 Amps

Supply & fixing in replacement of socket outlet 15 Amp, 2 in 1,3 pin 5 and 15 Amps

Supply & fixing in replacement of Fan regulator step type, 120 watts,

Supply and fixing in replacement of Ceiling rose, surface bakelite 3 terminal, 240 volts, 5 Amps with back plate of 3 mm thick bakelite, laminated hylem sheet of appropriate size & MS box of suitable size complete all as specified and as directed.

Supply and Fixing lamp holder,PVC/ Polycarbonate type with back plate suitable for batten fitting (angle /plain) complete all as specified and as directed

Supply and fixing in replacement of Distribution Board double Door made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating and IP 43 & IK 09 protection surface mounting SPN 08 way, 240 volts with bus bar rating 200 Amps, dust and vermin proof suitable for incorporation of MCB’s and isolators etc complete all as specified and as directed.

Supply and fixing in replacement of Distribution Board double Door made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating and IP 43 & IK 09 protection surface mounting SPN 04 way, 240 volts with bus bar rating 200 Amps, dust and vermin proof suitable for incorporation of MCB’s and isolators etc complete all as specified and as directed.

Supply and fixing in replacement of MCB SP 16 to 32 Amps ' C 'Curve , 240 volts AC supply, capacity not less than 10 KA connection complete all as specified and as directed.

Supply and fixing in replacement of MCB SPN 32 Amps ' C 'Curve , 240 volts AC supply, capacity not less than 10 KA connection complete all as specified and as directed.

Supply and fixing of LED tube fittings 20 Watt LUMILINE Basic all purpose surface and wall mounted LED batten with polycarbonate housing & integrated electronic driver connection complete all as specified and as directed

Supply and fixing in replacement of Recessed Mounted with PLUTO Neo PANEL 2X2 LED 42 Watt Environmental friendly, new generation,aesthetically designed, ultra modern recess mounting luminaire with high brightness SMD LEDs as light source, suitable for Armstrong/Grid ceiling complete all as specified and as directed

Supply and fixing ceilling fan 1200 mm sweep Single pole 230V , 50Hz complete with fan regulator and down rod connection complete all as specified and as directed

S & F in replacement of 25 Watt LED post top New generation, post-top, energy saving, environmental friendly, long life aesthetically designed with symmetrical light distribution, spun aluminium landscape luminaire with high power LEDs as light source connection complete all as specified and as directed

Material and labour including jointing and testing of cast iron sluice valves class PN-1.0, conforming to IS14846 flanged ends drilled having stainless steel spindle with cast iron wheel at top complete with nuts, bolts, washers and rubber gaskets including taking out unserviceable sluice valve and removal from site for the follwing sizes complete all as specified and as directed

80 mm bore

100 mm bore

150 mm bore

Supply and fixing in replacement 60 watt LED street light New generation energy saving and environmental friendly long life LED street light made up of pressure die cast aluminium housing with high efficient LED as lighting source and PC cover having TOP Opening seperate driver compartment with IP66 protection and impact resistance of IK07 including making connections with GI pipe 0.6mtr angle braket fixing on wall and connectng to ceiling rose with apropriate wire complete all as specified and as directed .

Supply and fixing in replacement 35 watt LED street light New generation energy saving and environmental friendly long life LED street light made up of pressure die cast aluminium housing with high efficient LED as lighting source and PC cover having TOP Opening seperate driver compartment with IP66 protection and impact resistance of IK07 including making connections with GI pipe 0.6mtr angle braket fixing on wall and connectng to ceiling rose with apropriate wire complete all as specified and as directed .

Supply & Fixing in replacement of PVC insulated multistranded copper conductor wire of size 2.5 Sqmm, 1100 volts grade connection complete all as specified and as directed

Supply only LED bulb of 9 watt

S&F in replacement rotational moulded polythylene water storage tanks of capacity 500 ltr triple layer cylindrical vertical with closed top hoisted and fixed in position for priming of centrifugal pump set complete all as specified and as directed in SSR part I

M&L for fabrication (welding work ) of MS Header/ any size upto 300mm MS pipe at various pump house site for connection of pipe , arresting leakges on header complete all as specified and as directed

Material and labour for painting two coat of synthetic enamel paint as per existing pattern on pipe surface/header connection including preparation of surfaces by scratching and removing the rust, red primer coat complete all as specified and as directed

Supply & fixing in install testing and commissioning of feeder pillar box ,indoor type cubical shape,three phase, 4 wire, Al bus bar for phases and neutral made out of CRCA sheet 2.0 mm thick ,factory fabricated , CPRI approved , powder coated ,dust and vermin proof , provn for ventilation , angle iron frame and four legs of 50x50x6mm thick angle iron ,2 ft long grouted on PCC foundation of height not less than 30 cm from the ground level , grouting properly ,and of suitable size to accomodate the items mentioned below and having seperate compartment /chambers for cable gallery busbar ,switch gear etc all as specified and comprising of following including necessary cable connections to the MCCBs ,voltmeter,Ammeter and cable lugs etc .

Al bus bar with PVC sleev suitable for 600 amps for phase & 400 Amp for neutral - 01Set.

Phase indicating lamps LED type ( red , yellow, blue) 01 set

Incoming MCCB 400 Amp 4 pole 36 KA with adjustable thermal and fixed magnetic release -01 No

outgoing MCCB 250 Amp 4 pole 36 KA with adjustable thermal and fixed magnetic release -02 No

outgoing MCCB 100 Amp 3 pole 16 KA with adjustable thermal and fixed magnetic release -04 No

ML-1.5 Star Delta starter fully automatic suitable for 415V AC upto motor 10 HP with ON/OFF & Trip indication including sheet enclosure-01 No.

Analog time switch 1 module-01 No

Single phase preventer-01 No

Supply & fixing in install testing and commissioning of feeder pillar box ,indoor type cubical shape,three phase, 4 wire, Al bus bar for phases and neutral made out of CRCA sheet 2.0 mm thick ,factory fabricated , CPRI approved , powder coated ,dust and vermin proof , provn for ventilation , angle iron frame and four legs of 50x50x6mm thick angle iron ,2 ft long grouted on PCC foundation of height not less than 30 cm from the ground level , grouting properly ,and of suitable size to accomodate the items mentioned below and having seperate compartment /chambers for cable gallery busbar ,switch gear etc all as specified and comprising of following including necessary cable connections to the MCCBs ,voltmeter,Ammeter and cable lugs etc .

Al bus bar with PVC sleeve suitable for 400 amps for phase & 300 Amp for neutral - 01Set.

Phase indicating lamps LED type ( red , yellow, blue) 01 set

Incoming MCCB 250 Amp 4 pole 36 KA with adjustable thermal and fixed magnetic release -01 No

outgoing MCCB 160 Amp 4 pole 36 KA with adjustable thermal and fixed magnetic release -02 No

outgoing MCCB 63 Amp 3 pole 16 KA with adjustable thermal and fixed magnetic release -02 No

ML-3 Star Delta starter fully automatic suitable for 415V AC upto motor 50 HP with ON/OFF & Trip indication including sheet enclosure.-02 Nos

ML-1.5 Star Delta starter fully automatic suitable for 415V AC upto motor 10 HP with ON/OFF & Trip indication including sheet enclosure. -01 Nos

Single phase preventer-01 Nos

Analog time switch 1 module-01 No

Supply & fixing in install testing and commissioning of feeder pillar box ,indoor type cubical shape,three phase, 4 wire, Al bus bar for phases and neutral made out of CRCA sheet 2.0 mm thick ,factory fabricated , CPRI approved , powder coated ,dust and vermin proof , provn for ventilation , angle iron frame and four legs of 50x50x6mm thick angle iron ,2 ft long grouted on PCC foundation of height not less than 30 cm from the ground level , grouting properly ,and of suitable size to accomodate the items mentioned below and having seperate compartment /chambers for cable gallery busbar ,switch gear etc all as specified and comprising of following including necessary cable connections to the MCCBs ,voltmeter,Ammeter and cable lugs etc .

Al bus bar with PVC sleeve suitable for 400 amps for phase & 300 Amp for neutral - 01Set.

Phase indicating lamps LED type ( red , yellow, blue) 01 set

Incoming MCCB 160 Amp 4 pole 36 KA with adjustable thermal and fixed magnetic release -01 No

outgoing MCCB 63 Amp 4 pole 16 KA with adjustable thermal and fixed magnetic release -03 No

ML-1.5 Star Delta starter fully automatic suitable for 415V AC upto motor 10 HP with ON/OFF & Trip indication including sheet enclosure.-03 Nos

Analog time switch 1 module-03 Nos

Single phase preventer-03 Nos

Supply & fixing in install testing and commissioning of feeder pillar box ,indoor type cubical shape,three phase, 4 wire, Al bus bar for phases and neutral made out of CRCA sheet 2.0 mm thick ,factory fabricated , CPRI approved , powder coated ,dust and vermin proof , provn for ventilation , angle iron frame and four legs of 50x50x6mm thick angle iron ,2 ft long grouted on PCC foundation of height not less than 30 cm from the ground level , grouting properly ,and of suitable size to accomodate the items mentioned below and having seperate compartment /chambers for cable gallery busbar ,switch gear etc all as specified and comprising of following including necessary cable connections to the MCCBs ,voltmeter,Ammeter and cable lugs etc .

Al bus bar with PVC sleeve suitable for 400 amps for phase & 300 Amp for neutral - 01Set.

Phase indicating lamps LED type ( red , yellow, blue) 01 set

Incoming MCCB 250 Amp 4 pole 36 KA with adjustable thermal and fixed magnetic release -01 No

outgoing MCCB 160 Amp 4 pole 36 KA with adjustable thermal and fixed magnetic release -02 No

outgoing MCCB 100 Amp 3 pole 16 KA with adjustable thermal and fixed magnetic release -02 No

ML-3 Star Delta starter fully automatic suitable for 415V AC upto motor 50 HP with ON/OFF & Trip indication including sheet enclosure.-02 Nos

Single phase preventer-02 Nos

Supply and fixing & installation in replacement of perforated MS cable tray of size 350x50x2mm including horizontal and vertical bends, prepared hanging system and other accessories including painting of cable tray of complete all as specified and as directed.

M&L for DI flange fittings of A/F Tee, D/F Bend and DI flange Socket Piece of size 80 to 100mm dia bore Equal incluidng required cutting existing pipe connection complete all as specified and as directed.

Material and labour for Brick work with sub class 'B' bricks straight or curved on plan exc. 6M mean radius built in CM (1:4) for pillar in Borewell complete all as specified and as directed

An amount of Rs 133022.00 shall be deducted from BOQ on account of schedule of credit

CHOUDHARY ELECTRICAL

M/s Adhikari construction co.

Rahul Enterprises

B.R. Enterprises