REPAIR TO DRAIN, CULVERT, COMPOUND WALL, FENCING, GATE, ROOF TREATMENT, CHHAJJA AND OTHER MISC WORK IN ZONE C AREA UNDER AGE B/R-I OF GE (E) JABALPUR

Amount

Demolition of cement concrete in ground floors and paving not exceeding 15 cm thickness (Below or above ground level) and removing rubbish to a distance n exc 100m and depositing at low lying area complete all as specified and directed.

Taking down cement plaster and raking out joints, hacking for key, scrubbing down with water built in cement mortar.

Demolition of brick work built in cement mortar or cement lime mortar including all quoins, arches etc complete.

Excavation in trenches n exc 1.5 mtr wide and n exc 1.5mtr in depth for foundation etc, nexc 10 sqm on plan & getting out as in hard/dense soil all as specified and directed.

M&L for cement concrete 1:4:8, type D2 using 40mm graded stone aggregate in foundations, filling and mass concrete.

M&L brick work with sub class 'B' bricks straight or curved on plan exc 6m mean radius built in CM 1:6 all as specified and directed.

All as per Srl item No 6 here-in-before but except bricks.

M&L for reinforced cement concrete (design mix) M-20 (using 20mm graded stone aggregate) as in walls, retaining walls, basement walls, ballast walls and the like; any thickness; above top of footings; including attached pilasters and buttresses.

M&L rendering 10mm thick on fair faces of brick work or concrete surfaces in CM 1:4 rendering is to be finished even and smooth (without using extra lime or cement all as specified and directed.

M&L for formwork to rough finish faces of walls, retaining walls, abutments, parapets and staircase railings and similar work including attached pillasters, buttresses, etc.; vertical or to batter.

M&l for 75mm bire UPVC Pipes (SCH-40) laid in weep holes complete all as specified & directed.

Returning filling in including ,spreading ,levelling watering and well ramming in layers n. exc 25 cm thick.

Removal of surplus soil to a distance n. exc 50 mtr from the starting point and at level of 1.5 mtr.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for complete all as specifiedof RCC jali of any description.

M&L 15mm thick rendering in CM 1:4 on of brick or concrete surface finished even and fair on walls etc.

M&L for providing precast cement concrete type B-0 (1:2:4) (12.5mm graded aggregate) as in louvers and jallies, 35mm thick (measured solid) set CM 1:4, including all mouldings but excluding frame.

M&L PCC (1:2:4) type B-1 (20mm graded aggregate) as in kerbs/coping and the like including weathering, slightly rounded or chamfered angles and throating, including formwork complete all as specified and directed.

M&L for cement concrete 1:3:6 type C-2 using 20 mm graded stone aggregate as in surface channels and drains complete all as specified and directed.

Extra for forming fair finished drain or channel not exc 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc complete all as specified and directed.

M & L for providing precast cement concrete 1:2:4 type B-1 using 20 mm stone aggregate as in cover slabs (any type) and similar work round square or rectangular in shape and set in CM 1:4 complete all as specified and directed. Note : All RCC manhole covers to be embossed with Month & year of casting.

M&L TMT bars 8mm dia, cut to length bent to shape required including cranking, bending spirally for hoping for columns , hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia quality confirming to Fe 410-5 or Fe 400-0.

All as per Srl item No 21 here-in-before but 10mm dia over.

Dismantling posts or struts (Wood, steel or RCC) any section including taking out embedded portion and making good disturbed ground in natural ground.

Excavating in post holes or single holes each n. exc 0.5 cum getting out returning filling in and ramming earth or broken rubble mixed with earth around in layers n. exc. 25 cm watering and removing surplus soil to a distance n. exc 50 m and making good surface of hard/ dense soil.

M&L rolled mild steel in post and struts in fencing including tops to shape as directed drilling holes notching for wire, etc flat iron fillets (for securing wire mesh etc) including all necessary drilling bolting or riveting etc and similar work conforming to Fe 290 Gde E 165

M & L cement concrete type C2 1:3:6 (40 mm graded stone Aggregate) as in embedding of precast post.

Dismantling of fencing wire mesh any type.

Supply only chain link fencing MS galvanized of wt not exceeding 4.00 Kg/Sqm.

Fixing only chain link fencing incl line wires of size 50/75x100mm to any type of standards, rails, straining bolts (weight of chain link fencing should be of not exceeding 4.00 Kg/Sqm).

S&F in repairs Galvanised. 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacing and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed each line wire to be measured).

M&L mild steel bolt machine made with hexagonal or square beads at one end and screwed the other or screwed both ends each screwed and to be fitted with washers and one hexagone or square but length of bolt exc 5 cms but not exceeding 10cm long dia shall be of 5 to 10mm dia.

M&L Mild steel round bars 10 mm dia and over, cut to length, bent to shape required including cranking bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (Annealed) not less than 0.9 mm dia all as specified confirming to Gde E 250 or Gde E 165.

M&L two coats of synthetic enamel painting over one coat of red oxide on steel and iron surfaces incl necessary preparation of surfaces.

M& L for painting to steel and iron surfaces of any description, over 10 cm width or girth, not otherwise described with two coats of black bituminous paint over a coat of red oxide primer including preparation of surfaces.

Taking down rain water pipe, soil waste pipe any size including all fittings all as specified and directed.

S&F in repairs 110mm PVC (SWR) pipes single socketed in any length including with rubber ring bends, 'Y' junction etc fixed to walls/floor with clamps, holdfasts etc including cutting holes in walls and making good with PCC 1:2:4 complete all as directed. Joints fixed with as per manufacturer direction.

All as per Srl item No 36 here-in-before 75mm dia.

S&F 110 mm dia PVC (SWR) bends any radius.

S&F 75 mm dia PVC (SWR) bends any radius.

S&F 110 mm PVC (SWR) junction single, (Single T) equal or unequal.

S&F 75 mm PVC (SWR) junction single, (Single T) equal or unequal.

M&L PVC (SWR) gully/nahani trap 75/110/125 mm, including with CP grating, setting and jointing with solvent cement as in repair.

S&F 110mm PVC (SWR) WC connector with lip ring.

All as per Srl item No 43 here-in-beforebut bent type.

S&F Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; square bars as in cupboards, wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165.

Supplying and laying of PVC pipe bearing ISI mark of IS-15328 150 mm dia minimum 4 mm thick incl jointing with coppler complete laid in trenches or floors complete all as specified and directed Make : Supreme/Kisan/Finolex

All as per Srl item No 46 here-in-before but 200mm dia.

Dismantling plain or corrugated steel sheeting, any gauge, thickness, incl nanital or similar pattern roof covering.

S&F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.5mm thick of any colour (Profiled pattern and joints/lapping filled with silicon compound) any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws. (Make :Tata(duroshine)/Cril/ JSW). including necessary cutting groves chasing to wall and making good with PCC 1:2:4 (20mm graded stone aggregate) & plaster in CM (1:3) complete all as directed.

S&F Pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.60mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, in ridges, hips, valley gutters, drip and straight flashings etc.fixed with self tapping screws as specified. (Make : Tata (duroshine) / Cril / JSW) complete all as directed.

Dismantling wrought iron or mild steel work of any description complete all as specified.

S&F for mild steel rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates confirming to Fe 410 -W (Gde- E- 250) quality- A including necessary welding complete all as specified.

S&F mild steel flat iron as in wind tie for roof including cutting & making holes for securing bolts, confirming to Fe 410-W (Gde-E-250) quality-A complete all as specified and directed.

M&L 15mm thick rendering on fair faces of brick work or concrete surface in cm 1:4 mixed with WPC as per manufacturer’s instructions, but not less than 3% by weight of cement finished even and fair without using extra cement complete all as specified and directed. Note: WPC shall be measured and paid separately undere relevant item.

Supply only Integral water proofing compound all as specified and directed.

M&L for rendering 15mm thick in CM (1:6), on fair faces of brick work or concrete surfaces, finished the surfaces even & smooth, without using extra cement complete all as specified and directed.

M&L for rendering 5mm thick in CM (1:3), on fair faces of ceiling surfaces, finished the surfaces even and smooth (without using extra cement), complete all as specified and directed.

M&L for rendering 10mm thick plaster in CM (1:4), on the top of chajjas, concrete surfaces, finished even and smooth (without using extra cement) and mixed with integral WPC as per manufacturer's instructions but not less than 3% by weight of cement complete all as specified and directed. Note :WPC shall be measured & Paid separately.

M&L for preparation of newly plastered surfaces or previously untreated surfaces of ceiling and applying three coats of white wash on ceiling, complete all as specified and directed.

M&L for for preparation of newly plastered surfaces of walls and applying two coats of oil bond distemper over and including chalk whitening preparatory to distempering complete all as specified.

M&L for Preparing newly plastered surfaces of walls and applying two coats of cement base paint over and including a coat of alkali resistant primer complete all as specified.

Removal of existing detoriated decayed tarfelt or any treatment including loose surface craping with scraper chiseling scarping of surface with wire brush or any other method and removing the scrapped materials debris to a distance n.exc 50m depositing where directed complete all as specified.

M&L cutting out cracks to V section in existing roofs/wall or terracing, cleaning out, wetting, grouting with cement and sand slurry 1:3 complete all as specified.

M&L PCC (1:2:4) type B-0 (using 12.5mm graded stone agg) as in filling under undulation of roof top/chajjas complete all as specified and directed.

Supplying and providing water proofing treatment over cleaned roof surface with Polymeric standard water proofing membrane, weight not less than 3kg/Sqm comprising of the following for Approachable roof. (i) Cleaning and sweeping and washing down with water to remove all dust etc from plastered roof surfaces/walls etc. (ii) Applying a coat of hot air blown bitumen of grade 85/25 grade confirming to IS-702 @1.2Kg/Sqm over a coat of bitumen primer @ 0.30 Kg/Sqm on prepared surface. (iii) One layer of polymeric water proofing membrane of weight not less than 3 Kg/Sqm centre core of HM HDPE film of thickness 90 micron sandwiched with high polymeric high molecular and fusible film with 100mm over laps with sides and ends. The over laps shall be sealed by flame including vertical surfaces after cutting necessary grooves and making good with PCC gola 1:2:4 type B1 etc adhere to hot blown bitumen all as per manufactures instructions. (iv) Over membrane applying a coat of hot blown bitumen of grade 85/25 confirming to ISD-702 @ 1.2 Kg/Sqm. (v) Binding material such as sand in dry condition @ 0.75 Kg/Sqm minimum shall be dusted over bitumen .

Dismantling floor, hearth or wall tiling incl cement mortar bedding (but not backing) removing rubish off the premised out side M.D. land all as specified.

M&L Non Skid ceramic/coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.18 sqmbut not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles laid over and including 15mm screed bed in CM (1:6) complete all as specified and directed.

M&L Non Skid coloured ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles laid over and including 15mm screed bed in CM (1:6) complete all as specified and directed.

M&L vitrified Ceramic light shade tiles 10mm thick (Square/ rectangular) polished area of each tile not exceeding 0.36 sqm as in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles laid and including 15 mm thick screed beding layer in CM (1:6) complete all as specified and directed.

M & L Glazed ceramic coloured tiles on vertical surfaces 350x250x7mm/ 450x350x7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match shade of tiles over and including 10mm thick rendering in CM (1:3) finished rough to receive tiles etc with shalicrete R/E (STP) water proofing compound as per manufacturer instruction .

M&L 75 mm thick PCC (1:3:6) type C-2 using 40mm gradded stone agg as in plinth protection surface finished fair and even without using extra cement as specified incl filling of joints in cement and bitumen mortar (1:2) complete all as specified and directed.

M&L for 100 mm thick PCC1:2:4 type B 2, using 40 mm graded stone aggregate as in hard standing finished even and smooth without using extra cement including spike rolling to surface or making inpressions of expanded metal whilst the concrete is complete all as specified.

M&L 25 mm thick cement concrete (1:2:4) type B-0 (12.5 mm graded stone aggregate) as in sub base of floors. Finished even and fair complete all as specified.

M & L 100mm thick cement concrete 1:4:8 type D2 using 40 mm grded stone aggrgate finished the surface even and fair complete all as specified.

Dismantling water tanks of capacity exc 250 Ltrs and n.exc 500 Ltrs complete all as specified.

S&F 500 litrs capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position complete all as specified and directed. Note : Tanks shall be ISI marked and having two layers. Make : Sintex/Polycon/JS Polyplast

Demolition of cement concrete of any description in any position, concrete filling in sunken floor complete all as specified.

M & L PCC 1:7:12 type F 2 with bricks course aggregate as in filling of sunken slab after laying carrying out required tests for CI pipes joints WPT complete all as specified.

Roughening surfaces of old concrete floor by picking,sweepping clean and washing down with water to remove dust etc complete all as specified.

M&L for 15mm thick rendering to sides and bottom of sunken slab in CM 1:3 with water proofing compound, finishing the surfaces even and smooth without using extra cement. Note :- WPC shall be measured & paid seperately.

M&L 40mm thick cement concrete type B-0 using 12.5 mm graded stone aggregate in sunken floors finished even and fair complete all as specified.

S&F in repairs GI spouts 50mm bore medium grade, projecting at least 10 cm clear of the wall complete all as specified and directed.

M & L for applying two coats of hot bitumen 85/25 grade @ 1.70 Kg/Sqm over vertical surfaces and floor of sunken slab after laying all CI connection branch pieces etc after covering joints with and including PCC (1:2:4) mixed with WPC complete all as specified and directed.

M&l for APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) land on primed surface by forced application complete all as specified & applying two coats of aluminium paint.

M&L Precast RCC 1 : 2 : 4 Type B1 ( 20 MM graded stone aggregate) as in cover slab (for manholes etc), chajjas, mangers, shelves etc. set in cm 1 : 6 complete with joints to match complete all as specified.

M&L 20 mm thick Granite (of any type) work (table rubbed and polished) in partition, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as directed.

Schedule of credit amount of Rs. 3,58,448.75 to be deducted during AOC

M/S CHETAN PRAKASH GOYAL

M/S BHARTI ENTERPRISES

M/S RAJ BUILDERS

JITENDER SINGH

Goodluck Enterprises

m/s R K SETHI