REPAIR /MAINT WORKS TO WATER PIPE INSTALLATION AND PIPELINE NETWORK AND CONNECTED WORKS AT KLP AREA UNDER GE BABINA

S & F in repairs GI fittings i.e bends, reducer, tail pieces, tapers, tees, caps and plugs with MS plate, nuts, bolts washers etc for size 40 to 75 mm bore complete all as specified and as directed.

Construction of Valve pit after dismantling of old u/s valve pit of Size 1050mm x1050mmx900mm (internal dimensions), Stone masonry constructton,tncludlng all necessary excavation and earth work in hard/ dense soil,returning,filling,in disposal of surplus soil to a distance not exceeding 50 m and depositing where directed , PCC in foundation of the mix (1:4..8) Type DQ (using 40 mm graded crushed stone aggregate), PCC Pocing in PCC(1:2:4), type BO using 12.5m crushed graded aggregate, brick masonry in cement mortar (1:4) rendering, 12 mm thick in cement mortar (1.4) Internalty,ftntshed even and fair and pointing flush externally as the work proceeds in the same mortar, Mild steel angle Iron 50x50x6mm frame,MS sheet cover 3.15mm thick with handle and locking arrangment ,painting ,all the exposed MS work with two coats of synthetic enamel paint of tint as approved by the GE/AGE over a coats of red oxide pnmer and painting all the MS embedded in PCC with two coats of black bituminous paint etc, Complete all as specified and shown on drawing.

Discription as per item no 4 here in before but 950mmx950mmx600mm

Supply and fix water pipe line route indicator made of size 400 x 300 x 25mm of precast RCC (1:2:4) type B-O using 12.5 mm graded stone aggregate complete all as specified and directed. Note :- Route indicator should be writen as main water supply line complete as directed by Engr-in-Charge.

S & F in replacement of ductile iron sluice valve of 80 mm bore class PN-1.6 ISI marked (as per IS 14846 of 2000) heavy duty with flanged ends with high tensile SS spindle and gun metal check nut, iron hand wheel and fixing with providing suitable nuts, bolts, washers and rubber gasket for packing etc complete all as specified and directed.Note:- Any damage made to pipe lines, over head reservoir while replacing the sluice valve will be repaired by contractor on his own cost. Make:-Kirloskar/leader/upadhayay/sant Note:- Contractor will be intimated to replace the deffective sluice balve on telephonically followed by in written. Contractor has to arrange new sluice valves and complete the replacement work with 48 hrs after intimation failing which a penal recovery of Rs 400/- per hour will be charged from his payment. Contractor has to keep all required size sluice valve and T&P with manpower ready for fixing on urgent requirment and quote his rates accordingly.

All as per Srl item No. 07 here-in-before but 100 mm dia bore

All as per ser item No 07 here-in-before but 150 mm bore sluice valve.

All as per ser item No 07 here-in-before but 200 mm bore sluice valve.

All as per ser item No 07 here-in-before but 250 mm bore sluice valve.

All as per ser item No 07 here-in-before but 300 mm bore sluice valve.

M& L for providing wiremesh to vent pipes, ventilation and entrance of OHT/UG sump at various location by providing beeding pieces at corners of ventilators and entrances of OHT and providing clamps to pipes for foxing wiremesh to pipe also applying red oxide and two coat enamel paint complete all as specified and directed

Repairs of cast iron sluice valve SS Spindle of 80 mm bore class NP 1.6 ISI mark heavy duty with replacement of unserviceable part high tensile SS spindle incuding spidal check nut , bolts ,washer and rubber gasket for packing etc complete all as specified and directed by Engr-in-Charge.

All as per ser item No 14 here-in-before but 100 mm bore.

All as per ser item No 14 here-in-before but 150 mm bore.

All as per ser item No 14 here-in-before but 250 mm bore.

All as per ser item No 14 here-in-before but 300 mm bore.

S & F in replacement of ductile iron non return valve of 80 mm bore ISI marked heavy duty with flanged ends fixing with providing suitable nuts, bolts, washers and rubber gasket for packing etc complete all as specified and directed.Note:- Any damage made to pipe lines, over head reservoir while replacing the sluice valve will be repaired by contractor on his own cost. Make:-Kirloskar/leader/upadhayay/sant

All as per ser item No 19 here-in-before but 100 mm bore.

All as per ser item No 19 here-in-before but 150 mm bore.

All as per ser item No 19 here-in-before but 200 mm bore.

All as per ser item No 19 here-in-before but 250 mm bore.

All as per ser item No 19 here-in-before but 300 mm bore.

S & F cast iron foot valves with flanged end in replacement of 80 mm bore all as per including necessary rubber gasket, MS nuts, bolts, washers etc of suitable size complete all as specified and directed. Make:-Kirloskar/leader/upadhayay/sant

S & F cast iron foot valves with flanged end in replacement of 100 mm bore all as per including necessary rubber gasket, MS nuts, bolts, washers etc of suitable size complete all as specified and directed.Make:-Kirloskar/leader/upadhayay/sant

S & F cast iron foot valves with flanged end in replacement of 150 mm bore all as per including necessary rubber gasket, MS nuts, bolts, washers etc of suitable size complete all as specified and directed.Make:-Kirloskar/leader/upadhayay/sant

S & F cast iron foot valves with flanged end in replacement of 200 mm bore all as per including necessary rubber gasket, MS nuts, bolts, washers etc of suitable size complete all as specified and directed.Make:-Kirloskar/leader/upadhayay/sant

S & F in replacement of 100 mm bore air release valve double chamber as per IS 14845 including mounting GI pipe and clamps as per requirement at site suitable for cast iron pipe/ ductile iron pipe incl all fittings washer, nuts & bolt etc complete all as specified and directed.

S & F in replacement of 150 mm bore air release valve double chamber as per IS 14845 including mounting GI pipe and clamps as per requirement at site suitable for cast iron pipe/ ductile iron pipe incl all fittings washer, nuts & bolt etc complete all as specified and directed.

S & F in replacement of ductile iron pipe fittings for spigot and socketed or flanged pipes i.e. bends, reducer, tail pieces, tapers, tees, caps etc of 80 mm to 300 mm bore pipe complete all as specified and as directed.

S & F in replacement of cast iron fittings for spigot and socketed or flanged ends pipe i.e. bends, reducer, tail pieces, tapers, tees, caps and plugs with MS plate, nuts, bolts washers etc for size 80 to 300 mm bore complete all as specified and as directed.

S & F in replacement of FASD starter in sheet metal enclosure suitable for 60 HP induction motor, 3 phase 440 volt complete with over load protection & adjustable relay range 45-75A, incl provision of mounting arrangement with MS flat strips 40 mm x 5 mm thick of suitable length and shape duly drilled and embedded to wall incl making good disturbed surfaces incl dismantling complete all as specified. Make : L&T or equivalent approved make.

S& F DI Mechanical joint (MJ) complete with collar, rubber ring all fitting, nut bolts with superior quality rubber ring set for 80 to 100 mm CI pipe /DI pipe complete all as specified and directed.Note:- the rate quated by contractor deemed to be incl necessary earth works.

Discription as per item no 34 here in before but 150 mm dia bore

Discription as per item no 34 here in before but 200 mm dia bore

Discription as per item no 34 here in before but 250 mm to 300 dia bore

Supply, installation, testing and commissioninng of split casing centrifugal pump sets only suitable for pumping water 2208 LPM discharge at 70 m head suitable for fixing 60 HP cast iron body with gun metal impellers including fixing of safety valve, pressure guage and priming valve etc mounted on channel iron base frame including nut, bolts & washers etc. bolts & washer as per manufacturer's instructions of suitable size all as specified & directed.

Excavation in trenches not exceeding 1.5 Mtr wide and not exceeding 1.5 Mtr depth and getting out for laying of pipe lines in any type of soil.

Returning, filling including spreading, levelling, watering and well ramming in layers not exceeding 25 Cm each in soil.

Removal of surplus soil to a distance not exceeding 50 Mtrs and depositing where directed at a level not exceeding 1.5 Mtr above the starting point.

M & L for cutting of stone block pavement/road a depth up to 1.5 mtr below the normal ground level and in width equal to external dia plus 300 mm for lay pipe line upto 300 mm dia across the road in horizontal position and making good the cut portion filled with PCC 1:3:6 type C-2 using 40 mm graded stone aggregates 450 mm thick from TOP over 300 mm thick hard core over filled earth to levelled with existing surfaces for smooth plying of vehicles etc complete all as specified and directed. The repaired portion will be match to the existing surface. Note • Cost of PCC ,hard core,stones and Earth shall deemed to be included in unit rate quoted by the tendered.

M&L for PCC 1:3:6 type C-1 using 20 mm graded stone aggregate as in foundations/foot path etc complete all as specified and directed by Engr-in-Charge.

Demolition of cement concrete in ground floors and pavings not exceeding 15 cm thickness below or above gound level including removal of debris complete all as specified and directed.

M&L for taking up or down steel water tubing and connections of 15 mm dia including cleaning for refixing complete all as specified and directed

Discription all as item No 45 here in before but of size 20 mm bore.

Discription all as item No 45 here in before but of size 25 mm bore.

Discription all as item No 45 here in before but of size 40 mm bore.

Discription all as item No 45 here in before but of size 50 mm bore.

Discription all as item No 45 here in before but of size 80 mm bore.

Discription all as item No 45 here in before but of size 100 mm bore.

Re-laying / re-fixing galvanised mild steel water tubing of 15 mm bore with and including all fittings laid in trenches, under floor or fixed to walls / ceilings complete all as specified and as directed.

Discription all as per item No 52 here in before but of size 20 mm bore

Discription all as per item No 52 here in before but of size 25 mm bore

Discription all as per item No 52 here in before but of size 40 mm bore

Discription all as per Item No 52 here in before but of size 50 mm bore

Discription all as per item No 52 here In before but of size 80 mm bore

Discription all as per item No 52 here In before but of size 100 mm bore

S & F galvanised steel water tubing medium grade 15 mm bore with all fittings such as bends, elbow, socket etc lad under floors/trenches or on walls with all fixing arrangments including leakage testing as per is 97684 complete all as specified and directed.

Discription all as per item No 59 here In before but of size 20 mm bore

Discription all as per item No 59 here In before but of size 25 mm bore

Discription all as per item No 59 here In before but of size 40 mm bore

Discription all as per item No 59 here In before but of size 50 mm bore

Discription all as per item No 59 here In before but of size 80 mm bore

Discription all as per item No 59 here In before but of size 100 mm bore

S & F in replacement of brass ball valves of size 15 mm bore ISI marked with iron wheel head, screwed both ends for iron pipe incl dismantling old U/s gate valve all as specified and directed

Discription as per item No 66 here in before but 20 mm bore

Discription as per item No 66 here in before but 25 mm bore

Discription as per item No 66 here in before but 40 mm bore

Discription as per item No 66 here in before but 50 mm bore

M & L for cutting of GI/DI/CI pipe 80 to 150 mm bore carefully for inserting fittings such as bend, tee, socket pieces, collar etc complete all as specified and as directed.

Supply, laying & testing in repair ductile iron pipe with socket and spigot ends of 100 mm bore class - K-7 , with ceramic epoxy lining /coating inside and external zinc coating with a bitumen finishing layer conforming to IS - 8329-2000 (Reaffiremed - 2005 Edition 4.1) suitable for "push on joints" in any lengths and including providing joints etc and including taking out old/ unserviceable CI / DI pipes from vertical position or from trenches etc complete all as specified and as directed.

Supply, laying & testing in repair ductile iron pipe with socket and spigot ends of 150 mm bore class - K-7 , with ceramic epoxy lining /coating inside and external zinc coating with a bitumen finishing layer conforming to IS - 8329-2000 (Reaffiremed - 2005 Edition 4.1) suitable for "push on joints" in any lengths and including providing joints (Tyton joints) etc and including taking out old/ unserviceable CI / DI pipes from vertical position or from trenches etc complete all as specified and as directed.

Supply, laying & testing in repair ductile iron pipe with socket and spigot ends of 200 mm bore class - K-9 , with ceramic epoxy lining /coating inside and external zinc coating with a bitumen finishing layer conforming to IS - 8329-2000 (Reaffiremed - 2005 Edition 4.1) suitable for "push on joints" in any lengths and including providing joints (Tyton joints) etc and including taking out old/ unserviceable CI / DI pipes from vertical position or from trenches etc complete all as specified and as directed. Note for item No 18 to 21 : (i) The cost of joints shall deemed to be included in unit rate quoted by the tenderer.(ii) Excavation and earth work shall be measured and paid seperately .

Supply, laying & testing in repair ductile iron pipe with socket and spigot ends of 250 mm bore class - K-9 , with ceramic epoxy lining /coating inside and external zinc coating with a bitumen finishing layer conforming to IS - 8329-2000 (Reaffiremed - 2005 Edition 4.1) suitable for "push on joints" in any lengths and including providing joints (Tyton joints) etc complete all as specified. Note for item No 18 to 21 : (i) The cost of joints shall deemed to be included in unit rate quoted by the tenderer.(ii) Excavation and earth work shall be measured and paid seperately .

Supply, laying & testing in repair ductile iron pipe with socket and spigot ends of 300 mm bore class - K-9 , with ceramic epoxy lining /coating inside and external zinc coating with a bitumen finishing layer conforming to IS - 8329-2000 (Reaffiremed - 2005 Edition 4.1) suitable for "push on joints" in any lengths and including providing joints (Tyton joints) etc complete all as specified. Note for item No 18 to 21 : (i) The cost of joints shall deemed to be included in unit rate quoted by the tenderer.(ii) Excavation and earth work shall be measured and paid seperately .

M&L for painting with two coats of synthetic enamel paint and re-writing the same description with colour of sign board, rising and distribution pipe line from semi UG sump to pump house, black colour paint on valve pit cover, valves, UG sump details on sump etc within the installation including preparation of old/existing surface, rubbing and removing rust, worn out old paint layers and other foreigh materials complete all as specified and directed.

M&L for repair of leakage/damage/defect in raising main through taking down the MS/GI pipe for ground level to OHT work after dismantling flange joints and including replacement of gaskeet /MS flang of same size if required and refixing the pipe on its original position vertially or horigentally of raising/supply line of OHT flanged type from ground level to top of the OHT of size 100/ 150 mm dia . The rate includes the dismantling of existing CI pipe of flanged type, sluice valve size as per fixed at OHT and for providing & welding of flanges on the pipes all as required and directed by the enginer in Charge. The contractor also ensure that the job will complete with in 24 hours to ensure the restoration of supply as directed.The quantity of water supply pipe and sluice valve laid/fitted will be measured and paid separately. Note:- The cost of taking down/dismantling any type of valves/flanges etc is deemed to be in included herein unit rate. the rate also included cost of necessary T & P man power required at site.

All as per Srl item No.78 here-in-before but 200 mm dia.

All as per Srl item No. 78 here-in-before but 250 mm dia.

Supply only Nylon braided PVC braided pvc flexible pipe , heavy duty 25 mm aii as per sample

S&F in replacement of 20 mm Ball valves (float valve) PTMT ,high pressure , with polythene float and fly-nut complete screwed for iron pipe suction pipe, including nut bolt & washers for joints and jointing material complete all as specified and as directed by Engineer in Charge.

M&L for MS Fabrication work, made out of structural steel sections as in frame work for cable & piping ducts / MS door panels etc at water supply installations, MS angles / flats / plain sheets of appropriate gauge, cut to size and made to the exisitng shape suitable for fixing MS chequred duct covers / door panels, including nuts, bolts and washers, welding / bracing works, bending cold or hot drilling holes for bolts in any shape or sizes as required including one coat of primer and two coats of synthetic enamel paint to the entire steel surfaces all as specified and directed.