Internal Electrification of Indoor Shuttle Court and associated works in Anupuram Township.

Amount

Design, manufacturing, testing at manufacturer's works packing, transportation, delivery, unloading, storage, erection, testing and commissioning of the 415 Volts Switch Boards at site as per the drawing, detailed specification and as directed by Engineer-in-charge.

Load Distribution Panel consisting of following: a) 2 Sets of Incomer Feeders with 125 Amps, 4 Pole, MCCB with CBCT, Shunt Trip Coil, operating handle, interlocking facility and all control, measuring units etc., b) 8 Sets of Outgoing Feeders with 63 Amps, 4 Pole, MCCB with Shunt Trip Coil, operating handle etc., c) 4 Sets of Outgoing feeders with 63 Amps, 4 Pole, MCCB with Shunt Trip Coil, operating handle etc., along with 32A AC Contactors with remote ON/OFF provision. d) Spares as loose item. 63 Amps MCCB - 2 Nos 125 Amps MCCB - 1 No.

Supply, installation, testing and commissioning of following control DBs made out of sheet steel enclosure as per the drawing, detailed specification and as directed by Engineer-in-charge.

Supply, installation, testing and commissioning of Lighting Control Distribution Board made out of sheet steel enclosure with 25 Amps, 30 mA RCCB, 24 Hours Timer, Contactor, Control Fuse, Indication Lamp, Auto / Manual provision etc.,

Supply, embedment of 400 mm (H) X 500 mm (W) X 150 mm (D) made out of sheet steel enclosure with 4 Sets of ON/OFF Push Buttons, LED indication lamps and Terminal connectors for controlling of shuttle court luminaires.

Supply and embedment of concealed type MS boxes of the following types and as specified in RCC/Brick/Concrete Block Masonry with finishing and making good as per the detailed specification. (Refer Sec VI, Clause No.15.10).

150 (W) X 150 (H) X 80 (D) mm, 1.6 mm thick sheet MS Box

200 (W) X 200 (H) X 120 (D) mm,1.6 mm thick sheet MS Box

Assembling, installation, testing and commissioning of MCB DB enclosure already embedded in the wall including supply of Engraved Circuit Identification Plate and Danger Board as per the detailed specification for the following size of MCB DBs. (Refer Sec VI, Clause No.15.3).

TPN 6 Way Distribution Board

Supply fixing testing and commissioning of the following RCCBs on Distribution Boards as per the detailed specification. (Refer Sec VI, Clause No.14.2).

RCCB DP 40 A sensitivity 30 mA, TYPE Hpi

RCCB DP 25 A sensitivity 30 mA, TYPE Hpi

Supply Installation testing and commissioning of the following MCB on Distribution Boards as per the detailed specification. (Refer Sec VI, Clause No.14.2).

6-32 Amps SP MCB (Type-C)

6-32 Amps FP MCB (TYPE-C)

Wiring for lights / fans /sensors/ Timer /Power point with 1100V grade FRLS insulated copper conductor wires in existing concealed/ Exposed PVC / ERW / Flo-coated Metal conduits as per the detailed scope of work, including supply of Wires, switches/ sockets, termination of copper wires at either end by crimping including supply of PVC Sleeves/Ferrules, Copper Crimping Lugs and connecting the wires to various switches, sockets, etc. including testing and commissioning as per the detailed specification.(Refer Sec VI, Clause No.18)

Wiring for Power Points with 2 Runs of 4.0 Sq.mm Copper wires for Phase, Neutral and 1 Run of 2.5 Sq.mm Copper wires for Earth from MCB Distribution Board to Single Phase Metal Clad Socket.

Wiring for Power point with 3 Runs of 2.5 Sq.mm Copper wires for Phase & Neutral and Earth from MCB Distribution Board to Power point through Control Switch Box including 16A modular switch, 6/16 Amps combined shuttered type Socket and 10A modular switch & 3 pin, 6A shuttered type Socket, Modular Plate.

Wiring for Light/Sensor/Fan Points with 2 Runs of 1.5 Sq.mm copper wires for Phase & Neutral and 1 Run of 2.5 Sq.mm copper wire for Earth from MCB Distribution Board to Primary light/sensor/fan point through Control Switch Box including 10Amps modular switch.

Wiring for Power point with 3 Runs of 2.5 Sq.mm Copper wires for Phase & Neutral and Earth from Control Switch Box to control switch box including 10A modular switch & 3 pin 6A, shuttered type Socket and 16A modular switch & 6/16A combined shuttered type Socket, Modular plate.

Wiring for Power point with 2 Runs of 1.5Sq.mm Copper wires for Phase & Neutral and 1 Run of 2.5 Sq.mm copper wire for earth from Control Switch Box to control switch box including 10A modular switch & 3 pin 6A, shuttered type Socket, Modular plate.

Wiring for Light point with 2 Runs of 1.5 Sq.mm Copper wires for Phase & Neutral and 1 Run of 2.5 Sq.mm Copper wire for Earth from Switch box to switch box and further to Light point including 1 No 10A modular switch

Wiring for Light point with 2 Runs of 1.5 Sq.mm Copper wires for Phase & Neutral and 1 Run of 2.5 Sq.mm Copper wire for Earth from Switch box to Light point/Ceiling fan including 1 No 10A modular switch

Wiring for fan point with 2 Runs of 1.5 Sq.mm Copper wires for Phase & Neutral and 1 Run of 2.5 Sq.mm Copper wire for Earth from Switch box to Fan point including 1 No 10A modular switch and 1 No step type Fan regulator.

Wiring for Light point with 2 Runs of 1.5 Sq.mm Copper wires for Phase & Neutral and 1 Run of 2.5 Sq.mm Copper wire for Earth from Light point to Light point /sensor/contactor.

Wiring for Exhaust/Wall mounting fan point up to 3Mtr height with 2 Runs of 1.5 Sq.mm Copper wires for Phase & Neutral and 1 Run of 2.5 Sq.mm Copper wire for Earth from Switch board to Power point including supply of 3 pin 6A shuttered type Socket, 2Nos. 2 Modular plate and 1 No 10A modular switch.

Wiring with 1 Run of 1.5 Sq.mm Copper wire

Wiring with 1 Run of 2.5 Sq.mm Copper wire

Supply and fixing following Modular front cover plate on existing modular metal/plastic boxes etc. as required. (Refer Sec VI, Clause No.15.7).

One/Two module

3 Module

4 Module

6 Module

1 Modular dummy plate

Supply, Installation, Testing and Commissioning of 195 Watts LED flood light luminaries in indoor shuttle court at the height of 7-12 M high as per the detailed specification.. (Refer Sec VI, Clause No.16.1 for installation).

Supply, transportation, installation, testing and Commissioning of 1200 mm long, 18 Watts (max), 2000 Lumen LED Batten with suitable clamps as per the detailed specification. (Refer Sec VI, Clause No.16.1 for installation).

Supply, transportation, installation, testing and Commissioning of 36 Watts (max), 4600 Lumen, surface mounting decorative LED flat panel Luminaires with PDC aluminium housing and PC Diffuser as per the detailed specification. (Refer Sec VI, Clause No.16.1 for installation).

Supply, transportation, installation, testing and commissioning of 9Watts (max) 900 lumens (min), 2 feet long surface mounted LED Batten as per the detailed specification. (Refer Sec VI, Clause No.16.1).

Supply, transportation, installation, testing and commissioning of 12 Watts (max), 1200 Lumen, surface mounting decorative LED flat panel Luminaires as per the detailed specification. (Refer Sec VI, Clause No.16.1).

Supply, transportation, installation, testing and commissioning of 18 Watts (max), 2000 Lumen, surface mounting decorative LED flat panel Luminaires as per the detailed specification. (Refer Sec VI, Clause No.16.1).

Supply, installation and testing 10 Watts (max), 1100 lumen LED Bulkhead Luminaires with integrated driver unit made of aluminium with suitable connecting leads as per the detailed specification. (Refer Sec VI, Clause No.16.1 for installation).

Supply, transportation, installation, testing and Commissioning of the Rope type LED lights as per the detailed specification and as directed by Engineer-in-charge.

Supply, installation, testing and commissioning of control driver for rope type LED light, as per the detailed specification and as directed by Engineer-in-charge.

Supply, Installation, testing and commissioning of following sizes of BLDC Ceiling Fans and safety steel rope with 3 Core, 1.5 Sq.mm flexible copper cable including earth connection. Remote shall be supplied along with the fan.

1200mm Sweep BLDC Ceiling Fan

1400mm Sweep BLDC Ceiling Fan

Supply, installation, testing and commissioning of following sizes of Wall Mounting Fans as per the detailed specification. (For Supply Refer Sec V and For Installation Refer Sec V & Sec VI, Clause No.17.4).

Wall mounting fans 400 mm Dia

Wall mounting air circulators 450 mm Dia

Supply, installation, testing and commissioning of following sizes of Wall Mounting Exhaust Fans including supply of Aluminium grill bracket with Stainless Steel Bolts for mounting of Exhaust Fan & Aluminium grill bracket and 3 Core, 1.5 Sq.mm PVC insulated & FRLS sheathed copper flexible cable of required length as per the detailed specification. (Refer Sec VI, Clause No.17.2).

230 mm dia Medium duty, Double ball bearing exhaust fan.

Supply, Loading, Transportation, Unloading at site, Laying, Testing and Commissioning of 1.1 KV grade of following size of the cable through direct in ground including excavation, sand cushioning, protective covering with chamber burnt/cement bricks on sides & top, refilling the trench and providing RCC route indicator etc as required.(Refer Sec VI, Clause No.3)

4C x 10 sqmm 1.1kV grade Aluminium conductor XLPE / HRPVC insulation flat wire armour FRLSH PVC outer sheath.

Supply, Loading, Transportation, Unloading at site, installation, Testing and Commissioning of 1100 Volts Grade following sizes of cables in built-in trenches, on walls, poles and through embedded pipes including supply of GI spacer, clamps etc and as per the detailed specification.(Refer Sec VI, Clause No.3)

4C x 10 sqmm 1.1kV grade Aluminium conductor XLPE / HRPVC insulation flat wire armour FRLSH PVC outer sheath.

Loading, Transportation, Unloading at site, Laying, Testing and Commissioning of one number PVC/HRPVC/XLPE insulated and PVC sheathed Stranded Aluminium/copper conductor power cable of 1.1 KV grade of following sizes direct in ground including excavation, sand cushioning, protective covering with chamber burnt/cement bricks on sides & top, refilling the trench and providing RCC route indicator etc as required (Note: Cable will be issued free of cost by the department).(Refer Sec VI, Clause No.3)

4 core x 16 sqmm

3.5 core x 185 sqmm

Loading, Transportation, Unloading at site, installation, Testing and Commissioning of 1100 Volts Grade PVC/HRPVC/XLPE insulated, Stranded Aluminium/copper conductor cables of following sizes in built-in trenches, on walls, poles and through embedded pipes including supply of GI spacer, clamps etc and as per the detailed specification (Note: Cable will be issued free of cost by the department).(Refer Sec VI, Clause No.3)

4 core x 16 sqmm

3.5 core x 185 sqmm

Loading, Transportation, Unloading at site, Laying, Testing and Commissioning of PVC insulated & Sheathed, armoured control cables of following sizes in built-in trenches, on walls, poles and through embedded pipes including supply of GI spacer, clamps etc and as per the detailed specification..(Note: Cable will be issued free of cost by the department).(Refer Sec VI, Clause No.3)

14 Core & Upto 37 Core 2.5 sqmm

End Termination of the following sizes of Aluminium Conductor PVC Insulated and sheathed armoured UG Cable using Single Compression, Heavy Duty, Gland connecting the cable to the equipment such as Switches/Panel Boards etc. using Comet or equivalent make Aluminium crimping lugs as directed by Engineer-in-Charge. The rate shall include the cost of supply of Cable Gland and Lugs. The Contractor shall arrange for making holes wherever necessary for fixing cable gland. (Refer Sec VI, Clause No.10.1).

4 Core x 10 Sq.mm

4 Core x 16 Sq.mm

3.5 Core x 185 Sq.mm

End termination of 1100 Volts Grade XLPE/PVC insulated, control cables of the following sizes using Single Compression, Heavy Duty, Siemens type Gland connecting the cable to the equipment such as Switches/Panel Boards etc. using Dowell's or equivalent make Copper crimping lugs as directed by Engineer-in-Charge. The rate shall include the cost of supply of Cable Gland and Lugs. The Contractor shall arrange for making holes wherever necessary for the completion of the work. (Refer Sec VI, Clause No.10.1).

19C x 2.5Sqmm

Supply, installation and testing of GI Pipe Earth Electrode as per IS: 3043 including RCC Chamber and RCC cover slab as per Drawing Nos.IGC/ESD/5060/1007/1 is enclosed. (50 Kg. Each Bentonite & Charcoal shall be provided for each earth pit). (Refer Sec VI, Clause No.12.4).

Supply, fabrication and installation of the following size of Hot dip Galvanised GI Flats including excavation and refilling as per the detailed specification. No cutting or drilling permitted after galvanisation. Refer Sec VI, Clause No.12.9).

50 x 6 mm GI flat

25 x 6 mm GI flat

Supply, fabrication and installation of the following size of Hot dip Galvanised GI Flats in Built in trenches on walls, poles, RCC Concrete and through embedded pipes as per the detailed specification. No cutting or drilling permitted after galvanisation. (Refer Sec VI, Clause No.12.9).

50 x 6 mm GI flat

25 x 6 mm GI flat

Supply and installation of 8 SWG G.I wire for earthing in built trenches and walls including termination using lugs, sleeves, bolts and nuts as per detailed specification and as directed by Engineer in charge

8 SWG GI wire

Supply Embedment Assembling testing and commissioning of following type Metra plug and socket DB and RCBO in sheet steel enclosure including chipping and finishing as per the detailed specification. (Refer Sec VI, Clause No.15.4).

32A 3P+N+E-FP Metra plug and socket DB

Excavation in hard soil including refilling with excavated earth and disposing surplus earth at places as directed with in a lead of 10 Mtrs. and initial lift up to 1.5 Mtrs. including neat banking as per detailed specification. (Refer Sec VI, Clause No.2)

Supply and Installation of MS Brackets, Supports, Frame work, Clamps, Base Channels, etc. fabricated out of angle / Channel / Rods etc. The rate quoted shall include the cost of fabrication / welding, cleaning and painting/ galvanising as follows including supply of required, fasteners, nuts, washers, etc.(Refer Sec VI, Clause No.11).

MS fabrication 1 coat primer & 2 coats synthetic enamel paint

Fabrication, Supply and installation of Stainless Steel Embedment Parts for Lightning Protection and grounding system as per the drawing No. GSO/ESG/ESD/ATS/SSGP/53362/EP-01 and as directed by Engineer in charge.

Supply and external installation of following sizes of Heavy Duty, PVC circular rigid Conduits for Electrical & Communication System with required Solid Long Bends, Couplings, GI Wire etc, as per the detailed specification.(Refer Sec VI, Clause No.27).

25mm Dia, 2mm wall thickness PVC heavy duty round rigid conduits with 50mm deep Junction boxes

Supply and Installation of following sizes of PVC trunking (casing & capping) on walls/Ceiling for routing of Power, Lighting and Telephone wires including all the required accessories like JBs, Coupling, External & Internal Bends, Elbows and end cap as per the detailed specification.(Refer Sec VI, Clause No.29)

25 x 12 mm size of PVC Mini trunking

Supplying, fabricating and fixing of EPs, Structural Steel work and pipe sleeves etc., in shutltle court comprising MS angles, MS Plates, test flats, rounds, squares, other structural steel sections, pipe sleeves and pipes of various sizes, IS channels, IS beams, Square rods, etc., of TATA or SAIL or approved equivalent make including cutting, welding , bending to shape, painting exposed faces with two coats of anto corrosive paint of approved colour over a coat of red oxide zinc chromite primer / zinc phosphate primer, embedding with Cement concrete, etc. complete all as per specifications.

Supply and installation of 10mm dia, Galvanised Steel Rope as per the detailed specification and as directed by Engineer in charge.

Supply and Installation of adjustable lock / U Clamp set suitable for 10mm Dia GI Rope size as per the detailed scope of work and as directed by Engineer in charge.

Providing and fixing a double scaffolding system (Cup-lock type) on the exterior (or) interior sides upto 9m height, using 40mm diameter M.S tubes spaced at 1.5 meters center- to-center both horizontally and vertically. The scaffolding shall have a working platform width of 3.00 to 4.00 meters and shall be assembled using the Cup-lock mechanism with appropiate M.S tube components joined using the cup and lock system, including M.S tubes, M.S challis, M.S clamps, base plates (or) vertical supports with rollers for mobility and a locking mechanism. The system shall also include an M.S staircase for acess to the working platforms. The scaffolding shall be stiffened with bracing, runners, and connections to the building wherever required for stability and inspection/working purposes. All necessary sefety features for the workmen shall be incorporated, and the system shall be maintained in a serviceble condition for the required duration as approved by the Engineer-in-charge. The scaffolding shall be dismantelled and removed after completion of the work etc., all complete as per the directions and approved by the Engineer-in-charge. (Note: The elevational area of the scaffolding shall be measured for payment pupose. The payment will be made once irrespective of the duration of the scaffolding)

SRIRAM ELECTRICALS (BID ID -3236707)

Bidder Name

CHANDRA REDDY ELECTRICALS

SRIRAM ELECTRICALS