Construction of Portico in the Ground floor entrance and providing cubicle arrangements in the 1st floor in the Administrative office building at Veerapandipirivu Milk Chilling centre

Amount

Dismanting of Reinforced cement concrete carefully and keeping the debris away from the site places as shown by the federation officers cost including all tools and plants etc., complete as directed by the departmental officers.

Dismanting of Plain cement concrete carefully and keeping the debris away from the site places as shown by the federation officers cost including all tools and plantsetc., complete as directed by the departmental officers.

Earth work excavation for foundation in all soils and sub-soils except hard rock requiring blasting inclusive of shoring shuttering, baling out water, refilling the sides of foundation watered, well rammed, consolidated, within the initial lead and lift leveling the site etc., complete as directed by the departmental officers.

Supplying and filling with Crushed Stone Sand for basement to required thickness, watered, well rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers.

Plain Cement Concrete 1:4:8 (One Cement, Four sand and eight hard broken stone jelly) using 40 mm gauge hard broken granite stone jelly for foundation including dewatering for flooring and foundation and including side shuttering, compaction, curing etc., complete as directed by the departmental officers.

Supplying, erection and steel centering for all RCC works using M.S Sheet, M.S. angles casurina props C.W.joints for all type of RCC works (ie) beams, roof slab, lintel, column footing, column & roof beam etc., including necessary supports with all cross bracing, filling the slits and holes the reprieved materials should be taken by the contractor and side shuttering etc., complete as directed by the departmental officers upto basement - Column surface

upto basement - plain surface

Above basement level 3.30m height- column surface

Above basement level 3.30m height-plain surface

Reinforced Cement Concrete 1:1½:3 (One Cement, One and a half sand and Three hard broken stone jelly) using 20 mm gauge hard broken granite stone jelly for all RCC items of works excluding cost of reinforcement grill and fabricating charges centering and shuttering but including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor / roof slabs wherever necessary and bearing surfaces of walls, beams etc. shall be finished smooth with Cement Mortar 1:3 (One Cement and Three Sand) and kraft paper laid over it without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers- Foundation & Basement

Above basement up to 4.50m height

Supplying, fabricating and placing in position of reinforcement, grills for all RCC works including cost of steel and binding wire , cutting and tying etc., complete by the departmental officers. MS/RTS rods in all floors

Brick work in Cement Mortar 1:5 (one part cement and five parts sand) using best quality II class Ground moulded chamber burnt bricks of size 9" x 4½" x 3" to line, level and to plumb on one face including necessary scaffolding, racking out joints, curing etc., complete as directed by the departmental officer and as per standard specification-For foundation & basement

Brick partition walls of 11.50cm thickness using best quality II class Ground moulded chamber burnt bricks of size 9" x 4-1/2" x 3" in Cement Mortar 1:3 (One Cement and Three Sand) using hoop iron reinforcement if found necessary including curing etc. complete and as directed by the departmental officers. (Hoop iron reinforcement will be measured and paid for separately)

Special ceiling plastering and finishing the exposed surface of all RCC items of work such as slabs, beams, sunshades, facia, canopy slab, staircase waist slab, landing slab etc., with Cement Mortar 1:3 (One Cement and Three Sand) 12mm thick including hacking the surfaces, providing cement mortar nosing, beading for sunshades, staircases, steps, landing slabs and curing, scaffolding etc., in all floors complying with standard specification and as directed by the departmental officers

Plastering with Cement Mortar 1:5 (One cement and Five sand), 12mm thick in all floors including curing and scaffolding etc. complete complying with standard specification and as directed by the departmental officers.

Painting two coats of newly plastered wall surface with ready mixed plastic emulsion paint (Exterior) of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty,scaffolding wherever required etc., complete complying with standard specification.

Providing Weathering course in brick jelly lime concrete using broken brick jelly of size 20mm uniform gauge in pure slaked lime (no sand to be used) to the proportion of brick jelly to lime being 32:12.5 by volume and laid over the RCC roof slab in a single layer of required slope and finished by beating the concrete with wooden beaters of approved pattern, keeping the surface constantly wet by sprinkling lime jaggery water, etc., complete as per standard specification and as directed by the departmental officers.

Finishing the top of roof with one course of machine pressed tiles of size 230mm x 230mm x 20mm of approved quality set in Cement Mortar 1:3 (One Cement and Three Sand) 12mm thick mixed with water proofing compound conforming to ISS at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete as directed by the departmental officers

Finishing the top of roof slab with one coarse of decorative tiles of approved quality laid in cement mortar 1:3, 20mm thick mixed with 2% of water proofing compound of approved quality by weight of cement etc,. complete as instructed by the federation officers and as per the standard specifications.

Supply & fixing of Aluminium partition with powder coated including single /double leaf doors, all aluminium sections at 2½"x1½" and bottom sections at 4"x1½" Jindal Aluminium clip 5mm thick glass Saint-Gobain glass/ Equal quality 8mm laminated Novapan particle board. All door materials should be branded 1st quality. The partititon height at required height with bottom 0.90m height with Novapan particle board, 1.20m height with 5mm thick glass, remaining height will be closed with Novapan particle board etc including door accessories like floor spring,door closer, handle wherever neccessary complete as directed by the departmental officers and as per standard specification

Chairman & General Manager Cabin Table: Main Table-2100mmx750mmx750mm (Ht), Side Storage-1800mmx450mmx750mm (Ht) Specification: Mobile pedestal support Table top 25mm thick pre-laminate particle board finished with 25mm PVC edge banded finish. Under Structure- Storage top is made of 25mm thick PLB boards with rest all made of 18mm thick PLB with openable shutters and one side pedestal support. Storage: storage top is made of 25mm thick PLB Boards with rest all made of 18mm thick PLB with openable shutters etc complete as directed by the federation officers and as per standard specification. The model should be got approved from the fedeation engineer before installation

Section Head Cabin Table: Main Table-1500mm(L) x 600mmx750mm (Ht), Side Storage-900mm(L)x400mmx750mm(Ht) Specification: Table top-25mm thick MDF and 1mm both side laminate finished with 2mm edge lipping finish. Under structure-Gable end and 18mm thick PLT modestry panel. Storage: storage top is made of 25mm thick PLB boards with rest all made of 18mm thick PLB MDF with openable structures. Power and LAN- 8 modules with USB port with wiring for room only. Wire management-Raceway below table top and skirting is considered only on main spine & rest with skirting only etc complete as directed by the departmental officers and as per standard specification.The model should be got approved from the fedeation engineer before installation

Supply & fixing of Cubicle with the following specification: L Shape 1200Lx1200Wx1200HT size System. Partition - 70mm Slide based of 1200Ht, finished with Fabric above & laminate tile below table top with one Marker Board and Soft Board Tile. Table top - 25mm thick pre laminated particle board finished with 2mm edge lipping finish. Understructure - End Partition and fitted with suitable brackets whereever required. Wire Management - Raceway Below Table top and Skirting is considered only on Main Spine & rest with Skirting only. Power and LAN - 8 Modules with USB port with wiring for room only as directed by the departmental officers and as per standard specification.The model should be got approved from the fedeation engineer before installation

Supplying and fixing of Toughened Glass for Conference room including Providing door of 12mm thick top & bottom teak wood finishing of 6" height and 2" breadth and the edges with high polish bottom 1'6" with designs etc., complete as directed by the departmental officers and as per standard specification

Mobile pedestal (2D + 1F) 400 w x 467D x 690 Ht (MW) made of 18mm thick PLB with 2 drawers & 1 filling cabinet etc., complete as per the directions of the departmental officers. The model should be got approved from the fedeation engineer before installation

Supply and fixing of the Storage cabinet of the following specification - Storage - 900L x 450D x 1200ht. 18mm Thk pre laminated particle board with openable shutters, adjustable shelves, and necessary handles with locks. The Colour and make should be got approved from the federation engineer.The model should be got approved from the fedeation engineer before installation

Supplying and fixing of files storage (rack) of size 900Lx600Dx1800ht (MM) 18mm thick pre laminated particle board with openable shutters, adjustable shelves and necessary handles with locks etc., complete and and as per the directions of the departmental officers. The model should be got approved from the fedeation engineer before installation

Supply and fixing of Conference Table for the following specificaion - 21 Seater Size - 7800L x 1800D x 750ht. Specification: Table top - 25mm thick Pre laminate particle board finished with 2mm PVC edge banded finish. Understructure - 25mm thick Pre laminate particle board finished with 2mm PVC edge banded finish. and modesty panel 18mm BSL PLB. - POP UP BOX - 10 Module, Hydralic cable cuppy, conference Table POP UP box with HDMI, VGA, Audio, LAN, Power ports & USB Port (Silver) - 8 No's. The entire setup should be completed as per the direction of the Federation Engineer.The model should be got approved from the fedeation engineer before installation

Supply and fixing of CONFERENCE ROOM AUDIO/VIDEO SET UP as per the following specification : PROJECTOR: EPSON Make EB - E01 Model. - SCREEN: Screen Size: 8' x 6' - AMPLIFIER: 5.1 Amplifier with 10 port mic pin and USB port, Then 5 No's of Speaker. - MIC: 8 No's of Wire Connection Mic and Wireless Mic 2 No's. etc complete as directed by the departmental officers and as per standard specification.The model should be got approved from the fedeation engineer before installation

Supply and fixing of AC high speed Ceiling fan complete 1200mm (48") with stepped electronic 300W regulator with 300mm down rod on the existing clamp

Supplying and fixing of Split AC (Daikin/Equivalent) 2.0 Tonnage Capacity 5 Star including cost and conveyance of all materials to site and labour charges for fixing in position etc complete as directed by the Departmental Officers.

Supply and fixing of 20A DP plug and socket in sheet enclosure with 32A DP MCB in flush with wall with earth connection (For AC Plug)

Supplying and fixing of WORKSTATION - JAZ with the following specification at good quality Medium IMPORTED Mesh Back Chair - MOULDED Cushioned Seat - Adjustable Lumbar Support - Gaslift - Synchro Mechanism - Adjustable Arms - Nylon BASE. The make and colour should be got approved from the federation Engineer before installation

Supply and fixing of CONFERENCE Room -JAVA Type Chairs for Conference room in the following specification of approved quality- Medium IMPORTED Mesh Back Chair - MOULDED Cushioned Seat - Adjustable Lumbar Support - Gaslift - Synchro Mechanism - Adjustable Arms - Chrome BASE. The make and colour should be got approved from the federation Engineer before installation

Supply and Fixing of Chairman and GM Room Chair as per the following specification - CABIN -OPTIMA - Medium IMPORTED Mesh Back Chair - MOULDED Cushioned Seat - Adjustable Lumbar Support / 4 Way Adjustable Arm Pad - Gaslift - Multilock Mechanism - Adjustable Arms - Metal BASE. The make and colour should be got approved from the federation Engineer before installation

Supplying and Fixing of Vertical Blinds for existing Windows of various sizes of approved quality etc., complete as directed by the departmental officers and as per standard specification

GST (Note: The tenderer should quote the amount towards Goods and Service tax (GST) in the appropriate columns in terms of percentage (%). If not quoted, it will be considered that the rate quoted is inclusive of GST.)