CLEANING OF SEWAGE LINE, SOAKAGE WELLS, SEPTIC TANKS, MANHOLES AND WATER TANKS AT QUEENS ROAD AREA IN ZONE-III UNDER GE (S) JAIPUR AT JAIPUR MIL STN

Amount

Cleaning and maint of sewage system including removing all type of blockage from wash hand basins ,bottle trap, kitchen sink, water closet sewage lines of any dia, manholes,by providing all tools and plants including bamboos, iron rod, bucket, rope, ladder etc and manpower as required complete all as specified and directed. Note:- (i) Contractor has to provide minimum Two Nos safaiwals /Sweepers daily to attend the sewage complaint which is received day to day by sub division. (ii) Any complaint which is not completed within two days from the date of issue of complaint, compensation will be charged @Rs. 200/- per day for each complaint (iii) No of blockage/ complaints cleared per day shall be recorded in MB is to be paid to the contractor as each Job. (iv) Cleaning of septic tank manhole and soakage well are paid separately under relevant item.

Cleaning of sewage line 100 mm dia SGWG /RCC NP 2 pipe or any other specification including removing all type of blockage from manholes to manholes by providing all tools and plants including bamboos, iron rod, bucket, rope, ladder etc Note:- (Contractor has to depute extra labour for cleaning of sewage lines to clear the blockage in sewer lines as and when required and disposing off all sludge waste debries etc to outside MD land complete all as directed.)

Ditto all as per Item No 2.00 above but 150 mm dia sewage line.

Ditto all as per Item No 2.00 above but 200 mm dia sewage line.

M&L for scooping, taking out sludge, foreign material and cleaning of manhole of depth n. exc 1.5 metre including tools and plants as required at site and disposed off sludge and foreign material by carrying out the same in covered van/ trolley out site defence land at place not more than 1.5 KM away from defence land at such a place which is not determental to public health and complete all as per direction of Engr in charge.

Ditto All as per serial item No. 5.00 here-in-before but depth exc 1.5 metre but n.exc 3.0 metre.

Scooping and taking out sludge, water and foreign material from septic tank, soakage well of any description and any depth including removing and re-fixing of septic tank and soak well cover etc including all tools & plants required at site and disposal of sludge and foreign material by carrying out the same out side in covered van/ trolley of defence land at such a place which is not determental to public health complete all as per direction of Engineer-in-Charge.

M&L for making arrangement for bypass to nearest manhole or line to keep sewage flow continuous by providing required necessary T&P and material such as portable pump set, flexible hose pipe etc complete all as required at site for following :-

Upto 30mtr distance

Beyond 30mtr but upto 60mtr distance

Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m depth for foundation etc or for shafts, wells cesspits manholes pier holes etc not exceeding 10 sqm on plan and not exceeding 1.5 m depth and getting out in soft /loose soil etc complete all as specified and as directed.

Ditto All as per item No 9.00 above but depth exc. 1.50 m but n. exc. 3.00 m

Removing excavated soil n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and as directed.

Returning, filing in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm in soft/loose soil etc complete all as specified and as directed.

M&L for Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (½ round or ¾ section) in cement concrete 1:2:4 type B-1 smooth finished ,and reforming benching as required for 100 mm internal dia of pipe complete all as specified and directed.

M&L for Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (½ round or ¾ section) in cement concrete 1:2:4 type B-1 smooth finished ,and reforming benching as required for 150 mm internal dia of pipe complete all as specified and directed.

M&L for Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (½ round or ¾ section) in cement concrete 1:2:4 type B-1 smooth finished ,and reforming benching as required for 200 mm internal dia of pipe complete all as specified and directed.

Demolition and breaking up drain pipe (salt glazed ware, AC or reinforced concrete ) set in cement mortar for 100 mm internal dia of pipe complete all as specified and directed.

Demolition and breaking up drain pipe (salt glazed ware, AC or reinforced concrete ) set in cement mortar for 150 mm internal dia of pipe complete all as specified and directed.

Demolition and breaking up drain pipe (salt glazed ware, AC or reinforced concrete ) set in cement mortar for 200 mm internal dia of pipe complete all as specified and directed.

M&L for cement concrete bed to drain pipes including packing under and haunching against the sides of pipe after they are laid & tested for 100 mm bore of pipe with cement concrete 1:4:8 type D-2 using 40mm graded stone aggregate complete all as specified and directed.

M&L for cement concrete bed to drain pipes including packing under and haunching against the sides of pipe after they are laid & tested for 150 mm bore of pipe with cement concrete 1:4:8 type D-2 using 40mm graded stone aggregate complete all as specified and directed.

M&L for cement concrete bed to drain pipes including packing under and haunching against the sides of pipe after they are laid & tested for 200 mm bore of pipe with cement concrete 1:4:8 type D-2 using 40mm graded stone aggregate complete all as specified and directed.

M&L for SGSW drain pipes laid in trenches of 100 mm internal diameter of pipe and jointed as specified complete all as specified and directed.

M&L for SGSW drain pipes laid in trenches of 150 mm internal diameter of pipe and jointed as specified complete all as specified and directed.

M&L for SGSW drain pipes laid in trenches of 200 mm internal diameter of pipe and jointed as specified complete all as specified and directed.

Disconnecting existing water tanks of capacity exc 250 liters but not exe 500 Ltrs setting aside or lowering if required for cleaning and reconnecting or refixing in same position,including cleaning and removing all scale and dirt etc from tanks and from the mouths of circulating pipes etc and including neatly writing date of cleaning (DD/MM/YY) upto 10 mm thick and upto 100 mm height each bold capital/ Italic letters with white/black synthetic enamel paint complete all as specified and directed.

Ditto all as per item No 25.00 above but capacity of tank exc 500 liters but n.exc 1000 Liters.

Dismantling of cast iron or reinforced concrete drain pipes, jointed in cement mortar for 100 mm internal dia of pipe and taking out of trenches if required complete all as specified and directed. Note-excavation work shall be measured and paid separately

Dismantling of cast iron or reinforced concrete drain pipes, jointed in cement mortar for 75 mm internal dia of pipe and taking out of trenches if required complete all as specified and directed. Note-excavation work shall be measured and paid separately

S & F cast iron soil, waste and vent 75 mm bore of pipes (sand cast) in any length with or without ears, with cement joints, laid in trenches or in floors complete all as specified and directed.

S & F cast iron soil, waste and vent 100 mm bore of pipes (sand cast) in any length with or without ears, with cement joints, laid in trenches or in floors complete all as specified and directed.

S & F cast iron soil, waste and vent 75 mm bore of pipes (sand cast) in any length with or without ears, with cement joints, fixed to walls complete all as specified and directed.

S & F cast iron soil, waste and vent 100 mm bore of pipes (sand cast) in any length with or without ears, with cement joints, fixed to walls complete all as specified and directed.

S&F 75mm bore Bends (any radius), diminishing pieces or tapers (larger bore measured) complete all as specified and directed.

S&F 75mm bore Branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches including taking down old branch pieces complete all as specified and directed.

S&F 100mm bore Branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches including taking down old branch pieces complete all as specified and directed.

S&F 100mm bore cast iron cowls including taking down old cowls.

M&L for PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls of 110 mm bore of pipe including taking down old pipe etc complete all as specified and directed.

S&F PVC (SWR) vent cowl 110 mm bore complete all as specified and directed.

S&F in repair SGSW gully trap square or round mouthed type 'P' of size 150 x 150 mm with CI grating including raising upto plinth protection with PCC 1:2:4 type B-1 and covered with stone slab complete.

Dismantling floor, hearth or wall tiling including cement mortar bedding etc (but not backing) and removing rubbish off the premises complete all as specified and directed.

M&L for non skid ceramic coloured tiles of design as approved 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles including 15 mm thick screed bed in cement mortor 1:4 complete all as specified and directed.

M&L for glazed ceramic coloured tiles 350 x 250 x 7 mm / 450 x 350 x 7 mm thick on vertical surface such as dado / skirting / risers to steps etc jointed in neat cement slurry and pointed in white or coloured cement to match surface of tiles over and including rendering 10 mm thick in cement mortor 1:4 complete all as specified and directed.

M&L for PCC 1:4:8 type D2 using 40mm graded stone aggregate as in foundation filling and mass concrete complete all as specified and directed.

Taking down cement plaster any description on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water complete all as specified and directed.

Demolition of brick work or stone/boulder masonry built in cement mortar including all quoins, arches, pillars etc complete all as specified and directed.

M&L Brick work using old size sub class 'B' bricks straight or curved on plan exc 6m mean radius built in cement mortar 1:4 complete all as specified and directed.

M&L Brick work (except brick) using old size sub class 'B' bricks straight or curved on plan exc 6m mean radius built in cement mortar 1:4 complete all as specified and directed. Note:- Old brick obtained from item 45.00 shall be reused.

M&L for rendering 15 mm thick in CM 1:4 on fair faces of brick work or concrete surfaces of wall and finished even and smooth by using WPC (deemed to be included in the quoted rate) @ 3% by weight of cement complete all as specified and directed.

Demolition of cement concrete un reinforced in ground floor and paving n exc 15 cm thick (below or above ground level) complete all as specified and directed.

M&L for PCC 1:2:4 type B-2 using 40 mm graded stone aggregate as in surface channels and drains including finishing the top of benching even and smooth using extra cement complete all as specified and directed. Note : Forming fair finished channel for drain using extra cement will be measured and paid for separately.

M&L Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred / stopped ends etc complete all as specified and directed.

Demolition of reinforced cement concrete in roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work (reinforcement cut as required to facilitate demolition) and removal of rubbish from site complete all as specified and directed.

Use and waste form work to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work not exceeding 200 mm thick (horizontal or sloping) for rough finished flat surface of concrete complete all as specified and directed

Use and waste form work to edges of concrete flats, treads breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roof and sides of bands in walls, horizontal or sloping and similar work for fair finished concrete surface exc 5 cm but not exc 10 cm wide complete all as specified and directed.

M&L for RCC (nominal mix) 1:1.5:3 type A-1 using 20 mm graded stone aggregate as in beam, cantilevers, bressummers, lintels over 1.5 m span and similar work complete all as specified and directed. Note - Reinforcement and form work shall be measured and paid separately.

M&L Providing precast cement concrete, Type B1 1:2:4 (20mm graded stone aggregate) in window or door cills, manholes, cover and similar work and setting in cement mortar 1:6 complete all as specified and directed.

M&L Mild Steel TMT bar 6 to 8 mm dia cut to length bent to shape required including cranking, bending spirally for hoping for columns hooking ends and binding with & including Mild Steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

Demolition of stone slabs and tiles of any description or thickness, laid bedded and pointed in any mortar in floor, apron etc complete all as specified and directed

M&L 50mm thick sand stone slabs; set and jointed in cement mortar 1:4 over joists, etc., complete all as specified and directed.

M&L for chequered cement concrete tiles 20 cm x 20 cm x 22 to 25 mm thick set, jointed and pointed in neat cement slurry as in floors with grey cement and no pigments complete all as specified and directed.

S&F machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade with grey cement and pigment over and including 25mm thick (compacted thickeness) sand bed complete all as specified and directed.

Ditto All as per item No 61.00 above but except tiles complete all as specified and directed.

M&L for 75 mm thick Cement concrete 1:4:8 type D-2 using 40 mm graded stone aggregate as in sub base complete all as specified and directed.

Hiring vehicle mounted sewer suction cum jetting machine of capacity 3000 to 12000 Liters with recyclening facility for cleaning / descaling/ maintance of sewer lines and manholes for underground drainage system complete all as directed by Engr-in-Charge.

S&F in repair Water closet vitreous china squatting pan, orissa pattern 580x440 mm white with integral foot rests excluding flushing cistern and flush pipe including provision of lime concrete bedding complete all as specified and directed.

M&L for vitreous china wash basin, white,flat back, size 550 x 400 mm with brackets, including supply & fixing pillar cock 15 mm bore CP fancy type, PVC connection of 450 mm long, PVC (HDPE) 32 mm bore waste pipe, brass couplings 32 mm CP etc complete all as sapecified and directed.

S&F in repair PVC 10 litres capacity valveless ,syphonic action type low level flushing cistern ,white including flush pipe, including brackets ,inlet, ball valve, float and handle etc complete all as specified and directed.

M&L in repair PVC (SWR) floor trap of diameter of outlet 75 mm, plain with grating including jointing with solvent cement complete all as specified and directed

M&L in repair for Vitreous China urinals, bowl type flat back size of 465 x 355 x 265 mm white (minimum) with grating and union for discharge pipe complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back in cement etc complete all as specified and directed.

M&L in repair wash down water closet vitreous china white pedestal pattern with 'P' or 'S' trap including connecting to outgoing drain pipe & to flushing pipe also including plastic water closet seat, black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device, excluding flushing cistern and flush pipe complete all as specified and directed.

M/S Chandra Mohan Bansal (BID ID -3112735)

S.R.Enterprises (BID ID -3115124)

Chaudhary Constructions (BID ID -3125979)

PUSHPA G ENTERPRISES (BID ID -3127060)

MSR INFRATECH (BID ID -3112085)

JAGDAMBA CONSTRUCTION COMPANY (BID ID -3114458)

m/s lovely cool air (BID ID -3120075)