SPECIAL REPAIRS TO STUDENT OFFICERS MARRIED ACCN NOS P 172 AT MILIT GIRINAGAR PUNE

Amount

B/R PORTION Demolition of cement concrete (unreinforced) in ground floors and pavings n. exc. 15 cm thickness (below or above ground level) and removing from site all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubish off the premises.

Demolition of cement concrete (Reinforced) in roofs, floors, beams staircase, landing chajjas and similar suspended work and removing from site all as specified and directed.

Demolition of Brickwork or stone masonary built in Cement mortar including all quions, arches, pillars etc but excluding ashlar facings, dressed stone work and precast concrete articles

Demolation of Concrete of any description and in any position not otherwise specifically provided for Kitchen platform

Taking down chowkats or frame of wooden or steel Not exc 1.5 Sqm with shutters (without taking of shutter from the frame).

Taking down chowkats or frames of wooden or steel exc 1.5 sqm & n.exc. 4 Sqm with Shutters (without taking off shutters from the frames).

Taking down cement plaster, any description on brick, concrete or stone walls or ceiling including racking out joints, hacking for key, scrubbing down with water etc and removal of rubbish off outside MD land all as specified and directed.

Forming jambs etc to opening including cutting toothing and properly bonding into old work including facing and pointing (if necessary) to match existing work complete in CM 1:4

M&L for Brickwork with flyash bricks straight or curved on plan exc 6m mean radius built in CM 1:6

Rendering 10 mm thick of fair faces of brick work or concrete work in CM 1;6. finished even and smooth without using extra cement.

Rendering 15 mm thick on brickwork or concrete work in CM 1:4 with waterproofing compound in double coat (10+5mm). Finished even and smooth without using extra cement.

M&L for complete removal of existing paint and applying two coats of oil bound distpemper over a coat of primer on old surfaces of wall

M&L for two coats of oil bound distpemper over a coat of primer on New surfaces of wall

M&L for complete removal of existing paint and applying two coats of oil bound distpemper over a coat of primer on old surfaces on old surfaces of ceiling

M&L for applying two or more coats of 100% premium acrylic emulsion paint having externally VOC less than 50gm/Litre and UV resistance as per IS 15489:2004, Alkali & Fungal resistance exterior paint of required shed (Company Depot Tinted) with silicon additives @ 1.43 Litre/10 Sqm over and including priming coat of exterior primer applied @ 0.90 Lit/sqm over new/old surfaces including complete removal of existing paint by bio wash, necessary scaffolding required for painting work, safety measures etc complete all as specified and directed

M&L for preparation of surfaces and applying 2mm thick wall care putty in two layers on walls/concrete surface internally complete all as specified and directed.

M&L for preparation of surfaces and applying waterproof 2mm thick wall care putty in two layers on walls/concrete surface externally complete all as specified and directed.

M&L for pressed steel frmaes for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc complete all as specified, supplied and fixed size 105X60mm

M&L for pressed steel frmaes for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc complete all as specified, supplied and fixed size 125X60mm

M&L for PCC 1:2:4 type B1 (20mm Graded stone aggregate) as in filling in frame and bed block for fixing of holdfast fo door frame.

S & F IInd class hard wood 35mm thick factory made, glazed and skeleton shutter open rebated and prepared to receive glass,gauge,etc.edges of framing plain,chamfered or rounded fitted with cut and mitred beads for securing glass,etc; size of members of shutters as specified in SSR Part I Sectin 8, clause 8.24 (a) ; supplied and fitted to chowkats

S&F Flush shutter solid core 30mm Thick with block board core and plywood face panels commercial type on both side with lipping/frame to match

S&F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm & fixed with stainless steel wire staples all as specified.

Preparation of new wooden surfaces exc 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer.

Preparation of new decorated Steel surfaces exc 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of primer.

S& F 2nd Class Hardwood Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed

French polishing on surfaces of any description, width or girth including cleaning and preparing the surface including a coat of wood filler on new works with two or more coats

M&L for Cupboard magnet including high quality magnet and steel plate.

S&F in repairs 18mm thick prelaminated particle board interior grade, conforming to IS-12823, Gde-I prelaminated both side with decorative choice lamination as in cupboard shutters, Kitchen cabinets etc fixed with screw including 3mm thick, ist class HW(TW) beading all around on edging to timber frame work all as specified and directed by Engr-in-Charge.

S&F continuous (Piano) hinges mild steel bright finished or electro galvanised width of flap 30mm complete all as specified and directed.

S&F 125mm cupboard handles fixed with nuts screws and washer of aluminium anodised complete all as specified and directed.

S&F Hasp and staples safety type aluminium with mild steel hinge pin including bolt to hinge plate and fixed with screws of 125mm size complete all as specified and directed.

S&F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet, reinforced with MS square tube, all as mentioned in Item No. 8095 of SSR Part-II.

S&F factory made solid panel PVC door shutter 30mm thick (stiles) consisting of frame made out of M.S tubes for top & bottom rails; M.S frame shall be covered with heat moulded plain colour PVC ‘C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail & bottom rail; panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification and drawing as per product Drg given on Sl. Page No. 156 of SSR Part-II 2010 Refer item No. 8080 as specified and directed by Engr-in-charge.

S & F butt hinges medium weight cold rolled mild steel size of hinges 100 mm

S&F brass sliding door bolts with sand or die cast brass hasp and staple (Bolt Type) and fixing bolt with rolled or drawin brass bolt and fixed length of bolt 250mm

S&F aluminium alloy, anodised, sliding door bolts with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section etc length of bolt 250 mm.

S&F aluminium anodised barrel tower bolts of extruded section 200 mm long.

S&F aluminium handles, anodised, cast type, of size 150 mm

S&F Brass handles, polished type, of size 150 mm

S&F 300mm MS ordinary rat tail rod pattern springs including roller and roller plate complete

M&L for floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring.

M&L for Powder coated aluminium frame for doors, windows, ventilators with one or more rebate including joining cleat for fixing etc complete.

M&L for Powder coated aluminium window and ventilator shutters, fixed type/sliding type without sash bar, aluminium section wighing 0.55 Kg/m including necessary joining cleats, glazing clips, rubber packing, Handle, lock, powder coated aluminium snap beading scres etc complete

M&L Framed work such as grills,gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, frame work of water tanks and similar work conforming to Fe-290.Gde-E-165.

S&F Stainless Steel fancy type curtain rod 25mm bore all as specified and directed by Engr-in-Charge.

S & F Stainless Steel brackets suitable for 25mm bore curtain rod (minimum projection from wall 75mm) fixed in wall including drilling, rawl plug, screws etc complete all as specified and directed by Engineer-in-Charge.

S&F sheet glass ordinary quality and glazing with oil putty in square n exc 0.5sqm each 3mm thk but frosted on one side

M & L for 25mm Thk Cement concrete type B-1 1:2:4 (20mm Graded stone aggregate) as in sub base or levelling course.

M&L for non skid, ceramic tiles 7 to 8mm thick (Square/Rectangular) area of each tile exceeding 0.06sqm but Not Exceeding 0.11 Sqm coloured tiles, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match complete over and including 15mm thick screed bed in CM 1:6 complete all as specified & directed by Engr-in-Charge.

M&L for coloured, glazed ceramic tiles as in vertical Surfacs 350X250X7mm/ 450x350x7mm thick,, laid and jointed in neat cement slurry and pointed in coloured cement to match complete over and including 10mm thick backing coat in CM 1:4 including triangular filleting on top in CM 1:4 complete all as specified and directed by Engr-in-Charge.

M&L for coloured glazed vitrified ceramic tiles 10mm Thick (square/Rectangular) polised, area of each tile exceeding 0.36 sqm but not exceeding 0.42 sqm as in floors, set and jointed in neat cement slurry and pointed in coloured cement to match with tiles, laid over and including 20mm thick screed bed in CM 1:6 all as specified and directed by Engr-in-Charge.

M&L for coloured glazed vitrified ceramic tiles 10mm Thick (square/Rectangular) polised, as in skirting, set and jointed in neat cement slurry and pointed in coloured cement to match with tiles, laid over and including 10mm thick backing coat in CM (1:3). all as specified and directed by Engr-in-Charge.

M&L for mirror polished Kota stone slab 20-25mm thick in Tread of steps in single pieces incl two numbers of grooves of size 3mmx3mm and rounding to edge, laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab incl rubbing and mirror polishing with and incl 10mm thick screed in CM(1:4) complete all as specified and directed by Engr-in-charge.

M&L for mirror polished Kota stone slab 20-25mm thick in riser or skirting of steps in single pieces laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab incl rubbing and mirror polishing with and incl 10mm thick screed in CM(1:4) complete all as specified and directed by Engr-in-charge.

M&L Kota stone flooring 20 to 25 mm thick laid, jointed with grey cement slurry and pointed with coloured cement to match the shade of Kota stone as in floor etc including rubbing and polishing laid over and including screed bed 20mm thick in CM 1:6 complete all as specified and directed.

S & F Machine cut cuddappa stone slab one side polished 20 to 25mm thick, set and jointed in neat cement slurry and pointed in coloured cement to match, laid over and including 20mm screed bed in cement mortar (1:6) .

M & L for granite 18mm thick (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite.

Rounding edges of stone one edge, such as in steps, cooking platform, window cill and other similar situation.

S&F in repairs 20mm dia brass chromium plated tubular towel rail, D type, 60cm long between flanges.

Taking up or down steel tubing 15mm bore and connections including removing from site

All as per item 14 above but 20 mm bore pipe.

S&F 20mm dia Unplasticised PVC pipes of pressure rating 10 kgf/cm2 fixed complete to walls, ceilings or in floors etc any type of pipe

S&F 15mm dia Unplasticised PVC pipes of pressure rating 10 kgf/cm2 fixed complete to walls, ceilings or in floors etc any type of pipe

S & F in repairs PVC connection 45 cm long 15 mm bore with 2 Nos PTMT check nuts.

S & F in repairs vitreous china wash down water closet pan Pedestal any colour including fixing bolts etc including PVC seat cover white with flat PVC low level flushing cistern 10 Ltr capacity with all internal fitting, inlet, outlet pipe connections etc complete all as specified and direcrted.

S&F in repairs vitreous china wash hand basin, white, 550x 400mm flat back including providing CI brackets, PVC waste pipe 32mm dia, CP brass waste coupling 32mm dia etc, 15mm bore CP fancy type pillar tap all as specified and directed.

S&F in repairs PVC (SWR) floor trap, dia of outlet 75mm, plain with grating including jointing with solvent cement.

S&F Stainless steel grating with ring 100mm dia

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc, and cutting chases for concealed water tubing or concealed conduit wiring, etc, and making good, cutting n.exc. 10cm girth.

S&F in repairs stop valves cast copper alloy, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe of for unions of bore 15mm complete all as specified.but fancy type, chromium plated

S&F in repair sinks with drainage board made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x160mm inlcluding 40mm waste coupling and waste pipe

S&F in repairs Brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixed

S&F in repairs Bib taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed but fancy type chromium plated

S&F 15 mm bore, two way bib tap, long body, fancy type, brass chromium plated, with crutch handle, screwed down for iron pipe and fixed etc. complete all as specified.

S&F brass 15mm dia CP hand shower (health faucet) with 1.2 m long flexible tube and wall hook as specified.

S&F in repairs brass Chromium plated fancy type Toilet paper holder of fixed to walls with chromium plated (CP) brass screws

S&F in repair brass Chromium plated fancy type Soap dish fixed to wall with Chromium plated brass screws

S&F in repairs 125mm Chromium plated shower roses with or without swivel joints, any size, including fixing to steel pipe or union

Dismantling cast iron work of any description

S&F PVC (SWR) pipes, single socketed in any length with rubber ring joints fixed to wall of size 110mm bore

S&F PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or in floors of size 110mm bore complete all as directed.

S&F PVC (SWR) pipes, single socketed in any length with rubber ring joints, laid in trenches or in floor of 75mm bore

S&F PVC (SWR) pipes, single socketed in any length with rubber ring joints, joints fixed to wall of 75mm bore

S&F PVC (SWR) junction, (Single Tee) equal or unequal 110mm bore

S&F PVC (SWR) junction, (Single Tee) equal or unequal 75mm bore

S&F PVC (SWR) bends any radius 110 mm bore

S&F PVC (SWR) bends any radius 75 mm bore with trap door

S &F PVC (SWR) branch piece, single (single Y) equal or unequal 110mm Bore

S &F PVC (SWR) branch piece, single (single Y) equal or unequal 75mm Bore

S &F PVC (SWR) branch piece, double (Double Y) equal or unequal 75mm Bore

S & F PVC (SWR) vent cowl 110mm Bore

S & F PVC (SWR) vent cowl 75mm Bore

S&F PVC (SWR) gully traps 125/100 setting and jointed in cement solvent.

S & F in repairs gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe of 20mm bore.

S&F ball valve high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe of 20mm bore.

Dismantling water tanks exc 250 but N exc 500 lts capacity including disconnecting water supply pipes and removing from to store all as specified

S&F PVC water storage tank 1000 Litrs capacity ISI marked rotational moulded double layer (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I. Including 20mm dia Tank Nipple suitable for HDPE water tank

M&L for roughening surfaces of old concrete floor of sunken portion by picking sweeping clean and washing down with water to remove dust etc and brushing neat cement slurry @ 3Kg/sqm complete all as specified and directed by Engr-in-Charge.

Rendering 10mm thick in CM 1:4 on concrete surfaces finished even and smooth using extra cement mixed with approved water proofing compound @ 3% weight of cement and apply two coats of Roff Hyguard EX Rezone Chemicals or equivalent make complete all as specified and as directed.

M&L for PCC 1:5:10 type E-2 (using 40mm graded brick aggregate) lean concrete for filling sunken floor.

Rendering 10mm thick in CM 1:3 on fair faces of brick work or concrete surfaces finished even & smooth without using extra cement duly mixed with water proofing compound @ 3% weight of cement over concrete surfaces complete all as specified and as directed. (Note :- WPC shall be measured and paid seperately)

Removal of entire existing water proofing treatment in any position including tarfelt plaster, lean concrete , gravels etc and removing the debirs out side MD land all as pecified and directed.

M&L for 10 mm thick rendering in CM 1:4 over concrete surfaces (Roof) mixed with water proofing compound @ 3% by weight of cement complete all as specified. Note: Water Proofing compound shall be measured and paid for seprately as "Supply Only"

M & L for APP based polymeric membrane minimum weight 3 Kgs/Sqm and minimum 3 mm thick reinforced with polyster non-woven fabric ( wt not less than 150 gms/sqm laid over primed surface with bituminous primer conforming to IS- 3384 @ 0.3 litre/sqm and finishing with preventive coat with aluminium paint @ 100m/sqm all as directed and specified including vertical surface.

Supply only WPC.

M&L for formwork to sides and soffits of lintel beam, floor or roof beam etc

M&L for formwork to soffits of suspended slab such as roof slab, floor slab, chajja and similar work not exceeding 200mm Thick

M&L for RCC Nominal Mix1:2:4 Type B1 (20mm Graded Aggregate) concrete in lintel beam, cantilever etc

M&L for RCC Nominal Mix1:2:4 Type B1 (20mm Graded Aggregate) concrete in Chajja and Similar works

S&F TMT bars 10mm dia and over cut to length, bent to shape required including cranking, bending, spirally for hooping for columns hooking ends and bindng with including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed

Same as per item above but 5mm dia and over upto and including 10mm dia in stirrups spacers and binders

SPECIAL ITEMS S & F for Modular kitchen cabinet and wall cabinet comprising of with including necessary all other fixing arrangement and screws as per requirement at site etc. All cabinet made of 18mm thick glossy/Matt Finish solid waterproof MDF board and outer door and topside shall be of 18mm thick perlam coloured solid MDF board, for fixing the items fitted in position and complete all as specified directed by Engr-in-Charge.

S & F 12 mm thick glossy/Matt Finish solid waterproof MDF board for kitchen wall cabinet back side and etc comprising of with including necessary all other fixing arrangement as per requirement at site. For fixing the items fitted in position to walls minimum screws size 120 mm complete all as specified directed by Engr-in-Charge.

S & F for stainless steel grill pattern Bottle Rack size 8" wide and 20" deep including stainless steel channels of make hettich, godrej or hafale.Dia of stainless steel bar used to make grill pattern shall be min 5mm fixing the items fitted in position and complete all as specified directed by Engr-in-Charge. MAKE:- Johnson kitchen, Hafele, Godrej interio and hettich or equivalent as approved.

S & F for stainless steel grill pattern basket of size 21"x4"x20" deep including stainless steel drawer channels of make hettich, godrej or hafale . Dia of stainless steel bar used to make grill pattern shall be min 5mm.Fixing the items fitted in position and complete all as specified directed by Engr-in-Charge.

S & F for stainless steel grill pattern basket of size 21"x6"x20" deep including stainless steel drawer channels of make hettich, godrej or hafale. Dia of stainless steel bar used to make grill pattern shall be min 5mm.Fixing the items fitted in position and complete all as specified directed by Engr-in-Charge.

S & F for stainless steel grill pattern basket of size 21"x8"x20" deep with including stainless steel drawer channels of make hettich, godrej or hafale. Dia of stainless steel bar used to make grill pattern shall be min 5mm. Fixing the items fitted in position and complete all as specified directed by Engr-in-Charge.

S & F for stainless steel Cuttlery Box of size 21"x4"x20" deep with including stainless steel drawer channels of make hettich, godrej hafale or equivalent as approved. Thickness of stainless steel sheet shall be 1mm thick. Fixing the items fitted in position and complete all as specified directed by Engr-in-Charge.

S & F for stainless steel grill pattern Grain Trolley with base of size 21"x24"x20"deep with including stainless steel channels of make Hafele, Godrej or hettich. Dia of stainless steel bar used to make grill pattern shall be min 5mm. Fixing the items fitted in position and complete all as specified directed by Engr-in-Charge.

S & F for stainless steel grill pattern Plate rack of size 21"x8"x20" deep with including stainless steel channels of make Hafele, Godrej, Hettich .Dia of stainless steel bar used to make grill pattern shall be min 5mm. Fixing the items fitted in position and complete all as specified directed by Engr-in-Charge.

S & F for stainless steel grill pattern Cup and Soucer Rack of size 21"x6"x20" deep with including stainless steel channels of make Godrej, Hettich or Hafale. Dia of stainless steel bar used to make grill pattern shall be min 5mm. Fixing the items fitted in position and complete all as specified directed by Engr-in-Charge.

S&F chromium plated auto hinges split box type overlay door mounting option, opening angle 110 degree fixed, with screw all as specified and directed. Make: Kea SCH or Hettich.

S&F 100 mm long cupboard stainless steel handles fixed with nuts screws and washer of complete all as specified and directed.

M&L for Cupboard magnet of size 50mm including high quality magnet and steel plate of complete all as specified and directed.

M&L for stainless steel frame work for fixing of modular kitchen below kitchen platform including necessary welding, fixing in true level and position as per availability of size below kitchen platform complete all as specified and directed by Engg-in-Charge.

EXTERNAL SERVICES Demolition of cement concrete (unreinforced) in ground floors and pavings n. exc. 15 cm thickness (below or above ground level) and removing from site all as specified and directed.

M&L for Hardcore of gauge n exc 63mm, deposited, spread and levelled in layers in not exc 15cm thick water and rammed to a true surface.

M&L cement concrete type D-2 1:4:8 (40mm graded aggregate) as in subbase 75mm Thk

M&L for Providing and laying 60mm thick factory made chamfered edge cement concrete coloured, glossy finish paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand;

M&L For cement concrete Type B1 (1:2:4) in kerb or mud stop rounded or champhered on edge.

AREA DRAINAGE Demolition of brickwork or stone boulder masonary built in cement mortar including all quions, arches, piller etc including dressed stone work.

Excavating in trenches, not exc 1.5m wide and not exc 1.5m in depth; for foundation etc. and getting out in Soft/loose soil, complete all as specified and directed.

M&L for PCC 1:4:8 type D2 (40mm graded stone aggregate) as in foundtion filling and mass concrete.

M&L for Brickwork with flyash bricks straight or curved on plan exc 6m mean radius built in CM 1:6

Returning, filling in, soft/loose soil including spreading, levelling, watering and well ramming in layers not exc 25 cm complete all specified and directed.

M&L PCC 1:2:4 type B-1 (20 mm graded aggregate) as in coping etc. including weathering slightly rounded or chamfered angle and throating complete all specified and directed.

M&L for framed work such as grills, gratings etc with ends of bar shoulderd and/or riveted or forged into spikes, framed guard bars, barred iron doors, ladders, framed baluster, walk way railing and similar work conforming to Fe 290 Gde E-165

M&L 10mm thick rendering in cement mortar 1:4 on fair faces of brick work or concrete surfaces finished even and smooth complete all specified and directed.

M&L for two coats of synthetic enamel paint over a coat of red oxide primer over New surfaces complete all specified and directed.

Removal of soil exc 250m but n Exc 500m and depositing where directed.

External Services Dismantling of mild steel framed work as in gates,doors,fencing post,etc. But excluding framed truss,complete all as specified and as directed.

Excavation in trenches not exc.1.5 mtr in width & not exc.1.5 mtr in depth for foundation of wall,pillars etc.and getting out in hard/dense soil.

M &L for PCC 1:4:8 type D-2 using 40 mm graded stone aggregate as in foundation of walls,pillars, etc.or mass filling concerete in fdn.complete all as specified &directed.

M&L for RCC Nominal Mix Type B1 1:2:4 (20mm Graded aggregate) concrete in Footing, Plinth Beam

M&L for RCC Nominal Mix Type B1 1:2:4 (20mm Graded aggregate) concrete in column, Piller

M & L for 10 mm and over dia TMT bars cut to length, bent to shape required incl cranking, bending spirally hooping for columns,hooking ends & binding with mild steel wire annealed not less than 0.9 mm dia securing with clips etc. Complete all as specifided &as directed.

Same as per item above but 5mm dia and over upto and including 10mm dia in stirrups spacers and binders

M & L for form work to sides of concrete in foundations,footing bases of columnns etc.complete all as specified & directed.

M &Lfor form work to sides of columns,pillars,posts etc.complete all as specified & directed.

M&L Framed work such as grills,gratings, Gates etc. with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, frame work of water tanks and similar work conforming to Fe-290.Gde-E-165 including portions framed and hung as gates including pintle hinges, stops hand made sliding bolts etc

M&L for Brickwork with flyash bricks straight or curved on plan exc 6m mean radius built in CM 1:6

M & L for 10 mm thick plastering on concrete or brick masonry surface of walls,finished surface even & smooth without using extra cement in cm 1:6 complete all as specified &directed.

M&L for applying two or more coats of 100% premium acrylic emulsion paint having VOC less than 50gm/Litre and UV resistance as per IS 15489:2004, Alkali & Fungal resistance exterior paint of required shed (Company Depot Tinted) with silicon additives @ 1.43 Litre/10 Sqm over and including priming coat of exterior primer applied @ 0.90 Lit/sqm over new/old surfaces including complete removal of existing paint by bio wash, necessary scaffolding required for painting work, safety measures etc complete all as specified and directed

Returning &filling in including spreading ,levelling ,watering &well ramming in layers not exc. 25 cm,complete all as specified &directed.

Removal of excavated material exc 250 m and N Exc 500m and depositing where directed at a level n exc 1.5 m above the starting point. (a) Soil

E/M SERVICES Taking down copper / aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc.removing materials for taking credit and making good disturbed surfaces of walls, floors and roofs etc all as specified and as directed.

Taking down sub main wiring complete including fitting and fixtures, removing materials for making good disturbed surfaces of walls, floors, roof etc, all as specified and as directed.

Taking down carefully unserviceable DBs any type/size With MCCBs/MCBs/Isolator etc and disconnecting and making good disturbed surfaces complete all as directed.

M & L Point wiring complete with 1.5 sqmm single core PVC insulated and unsheathed cable 1100 volts, FRLS grade with multistranded copper conductor ISI marked drawn through PVC concealed conduit fixed to walls / roofs / floors / ceiling etc. and including provision of 1.5 sqmm stranded copper conductor cable as earth continuity conductor and connected to common earth dolly, including modular cover plates with frame and modular flush boxes for mounting for housing the switches, socket outlets, fan regulators etc, all as specified and directed . (a) One light point controlled by one switch.

(b) One light point controlled by two way switch.

(c) One fan / Exhaust fan point controlled by one switch and one regulator.

(d) One bell point controlled by one bell push

(e) One 3 pin switch socket outlet point 5 Amps on independent board.

(f) One 3 pin switch socket outlet point 5 Amps on same board with other switch.

All as per item above here in before but with copper conductor cable for one 3 pin socket outlet, 15 amp independent, with cable 2.5 sqmm size.

S & Fix modular switch 1 way 6A, 1 module

S & Fix modular switch 2 way 6A, module

S & Fix modular switch1 way 16A, 1 module

S & Fix modular socket out let 6A 2/3 on combined 2 module

S & Fix modular socket out let 6A/16A-2/3 pin combined 2 module

S & Fix ceiling rose surface backlite 65x50 mm 3 terminals complete.

S & Fix fan regulator electronic 2 modular type volts AC 50 HZ, 100 Watts, 4 step complete all as directed.

S & Fix Bell push modular type SP 6 Amps.

S & Fix call bell (Ding Dong) 240 V, 50 Hz

S&Fix LED wall mounting fancy Light fitting,14 watt, 230 volts, complete with all accessories pre-wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size. all as specified & directed.Make :- Havells Cat Part No.LHFOECE1TZ1O014 or equivalent model of WIPRO / Philips / Bajaj and Jaquar

S & Fix LED Batten suitable for mount LED tube rod 1 x 18 watts including necessary electric connections with flexible copper cable 23/0.0076 from ceiling rose to tube light fitting complete all as specifed and directed by Engineer-in-charge. Make :- Bajaj Cat Part No - BLRB DB 118 or eqvt in Wipro/Havell/Crompton.

S & Fix LED tube light rod 18 watts with necessary fixing arrangement etc complete all as specifed and directed by Engineer-in-charge. Make - Bajaj Cat Part No - BLRB 18W LED or eqvt in Wipro/Havell/Crompton.

S&Fix LED Tube Light Fitting 10 watt, 230 volts, complete with all accessories all as specified & directed by Engr-in- charge.Make :- Bajaj Cat Part No - BCLSB WH 10 NT or eqvt in Wipro/Havell/Crompton.

S & Fix LED street light 30 W CUB type building security light pressure die cast aluminium housing LED street light lumaniries with IP 65 and bracket, nut,bolt,clamp etc complete all accessories and fixing arrengenment all as specified and directed by Engr-in-charge. Make - Bajaj Cat Part No - ENXT P 30L WH CR PC SD Havells Cat Part No -ENDURACITYLITEPLATPLUSSL30WLED757SASYBOPC / Crompton Cat Part No - LTRUMP0030XW or other.

S & Fix sheet metal enclosure MCCB DB VTPN double door 4 way suitable for 415 V with 200 amps rated bus bar including flushed on walls and making good disturbed surfaces all as specified and as directed..

S & Fix sheet metal enclosure distribution board SPN, 2 ways 240 volts with IP 43 protection and single door, suitable for mounting MCBs all as specified and as directed.

S & Fix sheet metal enclosure MCB DB TPN double door 4 way suitable for 415 V with 100 amps rated bus bar , IP 43 and reversible door type including flushed on walls and making good disturbed surfaces all as specified and as directed.

S & Fix MCB, single pole, 240 volts, 6 to 40 Amps, all as specified and as directed.

S & Fix MCB, single pole & neutral, 240 volts, 6 to 40 Amps, all as specified and as directed.

S & Fix MCB, Triple pole & neutral 415 volts, 32 to 63 Amps, all as specified and as directed.

S & Fix MCB, Triple pole 415 volts, 32 to 63 Amps, all as specified and as directed.

S & Fix MCCB , 4 pole, 415 volts,16 KA, 63 Amps, all as specified and as directed.

S & Fix Single pole and neutral enclouser with two pin and earthplug and socket complete with one single pole MCB with 240 V 20 AMPs.

M & L for submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor single core cable , multistranded and including suitable size of PVC concealed conduit and all accessories concealed in walls / roofs / ceiling etc. earth dolly, terminated in terminal box all as specified and directed by Engr-in-charge for the following. (a) 2x4 sq mm and 1x4 sq mm as earth wire

(b) 4x6 sq mm and 1x6 sq mm as earth wire

M&L for submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor single core cable , multistranded on the surface through and including suitable size of PVC conduit fixed to walls / roofs / floors / ceiling etc with its accessories all as specified and directed by Engr-in -charge for the following. (a) 2x1.5 sq mm and 1x1.5 sq mm as earth wire

Taking down and refixing of Ceiling fan / Exhaust fan any size/sweep, including oiling, Greasing and cleaning and applying two coats of synthetic enameled paint after preparation of surface complete over a coat of primer.

S & Fix PVC Body Exhaust fan AC single phase 220 to 240 volts 900 RPM of size 250 mm sweep with fixed on wall/ventilator and fixing arrangement complete all as specified & directed.

Taking down the existing unserviceable Geyser and after disconnecting electrically & mechanically and examine & carry out the servicing/overhauling the geyser by thoroughly cleaning the tank, thermostat, heatingelement and LED Lamp indicator, testing in all respect for smooth running and refixing complete all as directed.

Taking down the existing electric meter of any capacity and make after disconnecting electrically and carry out the cleaning and refixing, reconnecting including of electric meter, testing in all respect for smooth running completeall as directed.

M&L for earthing complete with galvanised steel earth plate electrode 600 X 600 X 6 mm thick buried directly in ground (earth pit not less than 2.25 M deep below ground level) with top edge of the plate not less that 1.5 M below normal grouond level connected to GI earth wire 4mm dia by means of nuts, bolts, check nuts, washers of galvanised iron or steel all as shown in electrical plate No 03 of SSR Part-I connected to earthing test point / DB including excavation / earth work in any type of strata, removal of surplus earth, GI pipe for watering pipe withand funnel, PCC 1:3:6 Type C-1 chamber with 40mm thick RCC 1:2:4 type B-1 in cover slab with TMT bars @ 150mm c/c both way with GI protection pipe complete all as specified and directed by Engineer-in-Charge

PAWAN B SHINDE

M/S OMSAI ENTERPRISES

M/S P D TUPE