Loading
Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L-1₹28.6 LAccepted-AOC 22 1755A KANNANKATTU TEMPLE ROAD EDAKOCHI KOCHI 682010 ERNAKULAM KERALA 682010 | ERNAKULAM | KERALA | 682010 | L-1 | Accepted-AOC Accepted | |
| 2 | L-2₹30.9 L+₹2.3 L (8.08%)Rejected-Finance | L-2 | Rejected-Finance High Rates | |
| 3 | L-3₹32.6 L+₹4.0 L (14.0%)Rejected-Finance | L-3 | Rejected-Finance High Rates | |
| 4 | L-4₹35.4 L+₹6.8 L (23.9%)Rejected-Finance | L-4 | Rejected-Finance High Rates |
| Sl No | Description | Qty | Unit | AGARWAL BUILDERS L3 | sanjay traders L1 | ENVIRO TECH SERVICES L4 | SAHYOG ELECTRIC L2 |
|---|---|---|---|---|---|---|---|
| 1.00 | Excavation in trenches not exc. 1.5 Mtr wide and not exc 1.5 Mtr deep in any type of soil and getting out complete all as specified and directed. | 340 | Cum | 110 ₹37,400 | 100 ₹34,000 | 65 ₹22,100 Lowest | 80 ₹27,200 |
| 2.00 | Returning filling in trenches including spreading, leveling, watering and well ramming in layers not exceeding 25 cm thick in any type of soil complete all as specified and directed. | 180 | Cum | 40 ₹7,200 | 100 ₹18,000 | 10 ₹1,800 Lowest | 25 ₹4,500 |
| 3.00 | Removing surplus excavated soil material to a distance not exc 50m and depositing where directed at a level not exc 1.50m above the starting point complete all as specified and directed. | 160 | Cum | 40 ₹6,400 | 80 ₹12,800 | 10 ₹1,600 Lowest | 25 ₹4,000 |
| 4.00 | M&L for filling approved fine river sand in trenches/ cable duct as cable cushion to the full width of excavated trench, under and over cable complete all as specified directed.
(Note : Punned thickness of sand shall be measured) | 145 | Cum | 1,500 ₹2,17,500 | 950 ₹1,37,750 | 850 ₹1,23,250 | 600 ₹87,000 Lowest |
| 5.00 | Supplying and laying reinforced precast concrete cable cover, class LV, type 1 with peak, size 250mm x 150mm x 40mm. | 11,300 | Each | 18 ₹2,03,400 Lowest | 20 ₹2,26,000 | 25 ₹2,82,500 | 18 ₹2,03,400 Lowest |
| 6.00 | M&L for treatment of existing high resistance earthing pit by pouring of salt water solution made of 20 ltrs of water and 5 Kg of salt in the trench to be prepared all around the existing earth pit with radious 60 cm from the centre of the earth pit to the centre of the trench with a depth not less than 30 cm below ground level all as directed and specified by the Engr-in-charge and levelling/ returning filling of earth surface. | 45 | Each Job | 200 ₹9,000 | 50 ₹2,250 Lowest | 200 ₹9,000 | 400 ₹18,000 |
| 7.00 | Supply and fix in replacement of Battery parallel plate type of capacity 12 V, 180 AH including taking down old unsv complete as specified. | 4 | Each | 19,000 ₹76,000 | 24,000 ₹96,000 | 18,000 ₹72,000 | 16,000 ₹64,000 Lowest |
| 8.00 | Supply, installation, testing and commissioning of LT Panel including taking down old unserviceable LT Panel out door type factory made CPRI Approved, water and vermin proof protection of size 2500mm x 1500mm x 800mm (over all dimension) made out of 3.00mm thick CRCA sheet dully supported with mild steel angle iron of size 50 x 50 x 6mm vertical frame and legs with mild steel flat iron 50 x 50 x 6mm in horizontal sides of the frame with front and back side openable, single hinged door/ shutter with locking arrengement and powder coated finish both internal and external steel surfaces after necessary preparation of steel surfaces including providing PCC (1:3:6) type C2 foundation of suitable size and connections of all outgoing/ incomming cable inclusive of necessary excavation and earthwork as required including the following fitment accessories and also including removing old exisisting one complete all as specified and as directed.
Note :- Rate of earthwork and PCC work are deemed to be inclusive in this item. | 2 | Each | 2,40,000 ₹4,80,000 | 1,85,000 ₹3,70,000 Lowest | 3,10,000 ₹6,20,000 | 3,50,000 ₹7,00,000 |
| 8.10INCOMMING (a) Copper strip busbar of size 800 Amps rated capaacity wrapped with PVC sleeves with maintained the colour code and provision of making holes with Copper nuts, bolts & washers for cable connections including hydrograpic insulators with nuts & bolts at both ends = 04 Nos. (b) 4 pole MCCB 400 Amps with rotary handle, adjustable thermal magnetic release type 415 Volts, Ics = 100% Icu, breaking capacity 35 KA including all fixing accessories with both ends spreader links - 01 No. (c) LED Neon indicator lamp (RYB) with holder and fuse holder 230/ 250 volts, AC -01 set (set of three). (d) Digital Ammeter of range (0 - 800) Amps, flush mounting type with CT’s of ratio 400/ 5 and selector switch - 01 set. (e) Digital voltmeter of range (0-500) volts, flush mounting type with selector switch - 01 No. OUTGOING (a) 4 Pole MCCB 250 Amps with rotary handle, adjustable thermal magnetic release type, 4 pole, 415 Volts, Ics = 100% Icu, 25 KA breaking capacity including all fixing accessories with both ends spreader links - 03 No. (b) 4 Pole MCCB 160 Amps with rotary handle, adjustable thermal magnetic release type, 4 poles, 415 Volts, Ics = 100% Icu, 25 KA breaking capacity including all fixing accessories with both ends spreader links - 02 No. (c) 4 Pole MCCB 100 Amps with rotary handle, adjustable thermal magnetic release type, 4 poles, 415 Volts, Ics = 100% Icu, 25 KA breaking capacity including all fixing accessories with both ends spreader links - 01 No. (d) Enamelled iron danger notice plate of 1.60mm thick mild steel sheet of size 200mm x 150mm, white with letters, figures and conventional skull and bones in signal red and fixed with nuts and bolts on door/ shutter of JB for LT - 01 No. | |||||||
| 9.00 | Supply, installation, testing and commissioning of LT Panel including taking down old unserviceable LT Panel out door type factory made CPRI Approved, water and vermin proof protection of size 2500mm x 1500mm x 800mm (over all dimension) made out of 3.00mm thick CRCA sheet dully supported with mild steel angle iron of size 50 x 50 x 6mm vertical frame and legs with mild steel flat iron 50 x 50 x 6mm in horizontal sides of the frame with front and back side openable, single hinged door/ shutter with locking arrengement and powder coated finish both internal and external steel surfaces after necessary preparation of steel surfaces including providing PCC (1:3:6) type C2 foundation of suitable size and connections of all outgoing/ incomming cable inclusive of necessary excavation and earthwork as required including the following fitment accessories and also including removing old exisisting one complete all as specified and as directed. Note :- Rate of earthwork and PCC work are deemed to be inclusive in this item. | 2 | Each | 2,20,000 ₹4,40,000 | 1,75,000 ₹3,50,000 Lowest | 3,25,000 ₹6,50,000 | 3,10,000 ₹6,20,000 |
Tender Value
₹35 L
EMD Value
₹70,000
Closing Date
12 Jul 2025, 6:00 pmClosed
Garrison Engineer (MCTE)
GE (MCTE) Mhow (MP) 453441
REPAIR/ REPLACEMENT OF LT PANEL OLD DAMAGED CABLE, PAINTING OF E/M INSTALLATION UNDER GE (MCTE) MHOW
2025_MES_714185_1
GE(MCTE)/MHOW/23(T) OF 2025-26
Open Tender
Electrical and Maintenance Works
Works
180 days
GE (MCTE) Mhow
As per Tender Document
10 documents required · 10 mandatory
₹500
Yes
GE (MCTE) Mhow
₹70,000
Yes
15 Sept 2025
13 Jun 2025
14 Jul 2025
13 Jun 2025
12 Jul 2025
28 Jun 2025
Amount
Excavation in trenches not exc. 1.5 Mtr wide and not exc 1.5 Mtr deep in any type of soil and getting out complete all as specified and directed.
Returning filling in trenches including spreading, leveling, watering and well ramming in layers not exceeding 25 cm thick in any type of soil complete all as specified and directed.
Removing surplus excavated soil material to a distance not exc 50m and depositing where directed at a level not exc 1.50m above the starting point complete all as specified and directed.
M&L for filling approved fine river sand in trenches/ cable duct as cable cushion to the full width of excavated trench, under and over cable complete all as specified directed. (Note : Punned thickness of sand shall be measured)
Supplying and laying reinforced precast concrete cable cover, class LV, type 1 with peak, size 250mm x 150mm x 40mm.
M&L for treatment of existing high resistance earthing pit by pouring of salt water solution made of 20 ltrs of water and 5 Kg of salt in the trench to be prepared all around the existing earth pit with radious 60 cm from the centre of the earth pit to the centre of the trench with a depth not less than 30 cm below ground level all as directed and specified by the Engr-in-charge and levelling/ returning filling of earth surface.
Supply and fix in replacement of Battery parallel plate type of capacity 12 V, 180 AH including taking down old unsv complete as specified.
Supply, installation, testing and commissioning of LT Panel including taking down old unserviceable LT Panel out door type factory made CPRI Approved, water and vermin proof protection of size 2500mm x 1500mm x 800mm (over all dimension) made out of 3.00mm thick CRCA sheet dully supported with mild steel angle iron of size 50 x 50 x 6mm vertical frame and legs with mild steel flat iron 50 x 50 x 6mm in horizontal sides of the frame with front and back side openable, single hinged door/ shutter with locking arrengement and powder coated finish both internal and external steel surfaces after necessary preparation of steel surfaces including providing PCC (1:3:6) type C2 foundation of suitable size and connections of all outgoing/ incomming cable inclusive of necessary excavation and earthwork as required including the following fitment accessories and also including removing old exisisting one complete all as specified and as directed. Note :- Rate of earthwork and PCC work are deemed to be inclusive in this item.
Supply, installation, testing and commissioning of LT Panel including taking down old unserviceable LT Panel out door type factory made CPRI Approved, water and vermin proof protection of size 2500mm x 1500mm x 800mm (over all dimension) made out of 3.00mm thick CRCA sheet dully supported with mild steel angle iron of size 50 x 50 x 6mm vertical frame and legs with mild steel flat iron 50 x 50 x 6mm in horizontal sides of the frame with front and back side openable, single hinged door/ shutter with locking arrengement and powder coated finish both internal and external steel surfaces after necessary preparation of steel surfaces including providing PCC (1:3:6) type C2 foundation of suitable size and connections of all outgoing/ incomming cable inclusive of necessary excavation and earthwork as required including the following fitment accessories and also including removing old exisisting one complete all as specified and as directed. Note :- Rate of earthwork and PCC work are deemed to be inclusive in this item.
S&F in replacement of old Solar LED light fitting 24 watt with new Solar Street Light is made with High Efficiency Mono Crystalline Solar PV Module, Lithium Ferro Phosphate battery with in-built BMS technology, High Efficacy LED, MPPT Solar Charge Controller and Aluminium Extruded body & is specially progrmmed to automatically control the dimming and brightness of light, which increases the backup time complete all as specified.
S&F MCCB, TPN, adjustable type thermal and magnetic, 415 Volts, including taking out old unserviceable MCCB from existing panel of any type and make complete of following sizes :-
160 Amps 36 KA complete all as specified
200 Amps 36 KA complete all as specified
250 Amps 36 KA complete all as specified
350 Amps 36 KA complete all as specified
400 Amps 36 KA complete all as specified
Taking out old unserviceable underground cable heavy duty armoured with aluminum conductor of any size complete all as specified.
S&L XLPE insulated, armoured, electric cable with aluminium conductor, multi stranded 1100 volts grade, laid in trenches, fixed on poles/ walls or passing through pipes including provision of necessary lugs and glands & making necessary connection complete all as specified and directed for the following:- (Note : excavtion and earth work, cable protection sand cushioning will be measured and paid seperately)
25 Sqmm, 3 1/2 core complete all as specified
50 Sqmm, 3 1/2 core complete all as specified
70 Sqmm, 3 1/2 core complete all as specified
95 Sqmm, 3 1/2 core complete all as specified
120 Sqmm, 3 1/2 core complete all as specified
150 Sqmm, 3 1/2 core complete all as specified
240 Sqmm, 3 1/2 core complete all as specified
S&F GI tubing, light grade, ISI marked 80mm bore pipe laid in trenches/ duct or in road crossing or fixed to wall/ poles for protection of cable incl taking out old pipe of any grade complete all as specified and directed.
All as per item No.14 above but 50mm bore pipe.
All as per item No.14 above but 40mm bore pipe.
M&L for painting to old chain link fencing and steel sections post with two coats aluminum paint over a coat of aluminium red-oxide complete including preparation of old steel or iron surfaces all as specified and directed.
Cutting the existing bituminuos road for passing of UG cable in road crossing and making good the disturbed surface of road to its original specification complete all as specified and directed.
Cutting, trimming and prunning of trees/ tree branches of any girth all around with 2 meter radius existing LT over head lines/ surrounding street light and flood fitting including cleaning the area beneath the LT overhead lines and removing the debris from the site and depositing where as directed by Engr-in-charge.
M&L for cleaning the area including uprooting of weeds/ grass and removing creepers from fencing or poles/ posts and brooming the complete area of sub station around panels, transformers and four pole structures all as specified & directed.
Taking down unserviceable/ burnt out MCB from existing LT Panel board duly disconnected all electrical connection & Supply and fixing new MCB SP 6-32 Amps, incl making necessary cable connection complete all as specified and directed.
Taking down unserviceable/ burnt out MCB from existing LT Panel board duly disconnected all electrical connection & Supply and fixing MCB 63 Amps TPN, incl necessary cable connection complete all as specified and directed.
S&L or fixing 1100 volts grade havey duty 4 Sqmm twin core flat/ circular PVC insulated aluminium conductor served with an inner sheathing of PVC tape overall PVC sheathed in service connections suspended by insulating hangers not more than 1 mtrs apart complete as specified and directed.
All as per item No.23 above but 6 Sqmm 2 core
All as per item No.23 above but 10 Sqmm 2 core
Supply and fixing cable route indicator, made of MS sheet of size 200mm x 150mm x 3mm thick, spot welded with angle iron of size 40 x 40 x 5mm thick, 750mm long embedded in PCC (1:2:4) type B-2 (using 40mm graded crushed stone aggregate) block 30cm x 30cm x 40cm in ground including one coat of synthetic enamel black paint over one coat of red oxide zinc chrome primer and writing with white paint showing size of cable HT/LT complete all as specified & directed.
M&L for earthing complete with GI steel earth plate electrode 60cm x 60cm x 6.0mm thick barried directly in ground vertically to a depth not less than 2.25 metres below ground level with top edge of earth plate at a depth not less than 1.5 mtrs below level ground, connected to GI strip 32 x 6mm by means of nuts, bolts checks nuts and washers made of GI earth wire protected by GI pipe 40mm bore, medium grade and connected to main switch board or main control board as directed and including concrete pit in PCC (1:3:6) type C1 (using 20mm graded crushed stone aggregate) pre-cast RCC (1:2:4) type-B-1, cover slab 30cm x 30cm x 10cm with one lifting handle made out of 8mm dia MS bar funnel wire mesh, 20mm bore GI or GI pipe medium grade for watering, charcoal or coke and salt in alternate layers, including necessary excavation and earth work in any type of soil complete all as shown in electrical plate No 3 of MES schedule Part-I and testing after completion including taking down old unsv Note:- 7.5 Meter GI strip size 32 x 6 is inclusive in above quoted rate.
M&L for scrubbing out old paint, rust etc from 9 mtr steel tubular pole of any size including cross arms, brackets & anti climbing divices and making smooth and even surface then painting with one coat of anti rust paint and two coat of superior quality aluminium paint on entire exposed portion of pole structure and writing Abbreviated feeder name in 2" size with white paint on black base all as directed at site (work shall be completed in the stipulated period complete as specified).
M&L for scrubbing out old paint external surfaces of HT 2 pole structures consisting of cross arms, GOD assy with pipe, DO fuse assy, clamps etc., of any description and applying one coat of Aluminium paint by mannualy (Except PCC/ RCC Pole) complete as specified. Note:- This rate inclusive of painting all minor items such as clamps, brackets, nuts, bolts and washers which is not particularly mentioned inthe structures & Each job will be measured and paid.
M & L for Painting of transformer of capacity up to 300 KVA, 11/.433 KV with two coats synthetic enamelled spray painting after preparation of transformer surface complete all as specified and directed.
All as per item No.30 above but capacity 315 to 750 KVA 11/0.433 V
Material and labour in welding and spray painting (both weldind and painting whenever required) of old exiting lt panel of any size. Note:- Repairs to LT panel boards complete with necessary welding works to door, replacement of unserviceable hings and all drop bolt, complete and painting with one coat of synthetic enamel paint of approved colour internally and externally complete all as specified and directed
Maintenance of indoor sub stations, including cleaning of premises and surroundings upto 5m from outer face of wall, dusting of panel checking of DC and AC connection, functioning of tube light, exhaust fan etc complete as specified at site.
S&F in replacement of DO fuse element 10 Amp for 11 KV complete all as specified and directed.
S&F in replacement of DO fuse element 20 Amp for 11 KV complete all as specified and directed.
S&F in replacement of DO fuse element 30 Amp for 11 KV complete all as specified and directed.
S&F in replacement of DO fuse element 50 Amp for 11 KV complete all as specified and directed.
S&F in replacement of DO fuse element 30 Amp for 33 KV complete all as specified and directed.
S&F in replacement of DO fuse element 50 Amp for 33 KV complete all as specified and directed.
S&F in replacement of DO fuse element 100 Amp for 33 KV complete all as specified and directed.
Treating surfaces of steel and iron work, any description, width or girth, with ready mixed paint, dead black; each coat complete as specified.
SAHYOG ELECTRIC (BID ID -3347688)
AGARWAL BUILDERS (BID ID -3342798)
ENVIRO TECH SERVICES (BID ID -3348160)
stage.html
html • 0.05 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.04 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .