SPECIAL REPAIR TO BLDG NO. T-47 AND T-54 AT BENGDUBI MIL STN UNDER GE BENGDUBI

Amount

Dimantling of Asbestos cement (corrugated, semi corrugated, etc.) sheets in roof coverings including ridges, valley gutter etc, complete all as specified and as directed.

S&F pre-painted colored trapezoidal profiled Galvalume/Zincalume sheet with min 0.50mm TCT confirming to IS-513 (AZ-150 GSM, AL Zn alloy metalic coating, 550 MPA yield stress as per AS-1397), colour /exterior coat of silicon modified polyster/ BHP X RW paint system 20 micron top coat applied over 5 micron primer and a 5 micron polyster back coat applied over 5 micron primer, as in roof covering, cladding to wall, fixed with and including Galvanised self drilling self-tapping fastener (12-14 x 55 with EPDM seals), complete all as specified and directed.

S&F pre-painted colored plain sheet profiled Galvalume/Zincalume sheet with min 0.50mm TCT confirming to IS-513 (AZ-150 GSM, AL Zn alloy metalic coating, 550 MPA yield stress as per AS-1397), colour /exterior coat of silicon modified polyster/ BHP X RW paint system 20 micron top coat applied over 5 micron primer and a 5 micron polyster back coat applied over 5 micron primer,as in roof covering, cladding to wall, ridge, valley gutter, fixed with and including Galvanised self drilling self-tapping fastener (12-14 x 55 with EPDM seals), complete all as specified and directed.

Dismantling wrought iron as in rafters, purlins, truss etc and/or mild steel work of any description not otherwise provided for, complete all as specified and as directed.

Dismantling timber fillets, rails, posts, rafters, purlins, etc. under 40 sq. cm in section, complete all as specified and directed.

Dismantling timber scantlings 40 sq. cm and over in section, in any position like trusses, rafters, purlins etc, complete all as specified and as directed.

S&F mild steel rolled sections [Fe 410-W (Gde E-250) quality - B] as in roof trusses (framed), trussed, main and cross beams, hip and jack rafters, purlins, Gusset plate and base plates, where connected to common rafters and running rails, distance pieces, cleats, guides for sliding doors; fixed with angle cleats or other connecting plates, framing for cladding, staging for water tanks, nuts, bolts, washers etc,includng welding or riveting etc, complete all as specified and as directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation, etc) or insulation boards/slabs/ blankets, any thickness, including cover fillets, and existing frame work also, complete all as specified and as directed.

S & F 6mm thick Non-asbestos fibre cement decorative/designer building boards (6mm thick pre-painted designed decorative type E-Board) to GI frame work with screws in ceiling (flat and/or slopping) and including jointless finish with & also including joining compound and tape as per manufacturer instructions, complete all as specified and as directed. Note :- The board shall be confirming to IS-14862 and shall be manufactured from the homogeneious mixture of cement, quartz and cellulose and shall be curred with high pressure steam using auto claving process.

S&F of GI frame work (with size of grid 605mmx605mm) for seamless ceiling comprising GI perimeter channel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre including provision of hangers (length of hangers as required at site) made of 4mm dia GI wire and other accessories, complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), including disposing off the retrieved debris outside the premises, complete all as specified and as directed.

Demolition of stone slabs, Paving Blocks and stone tiles of any description or thickness laid, bedded and pointed in any mortar as in floors, approaches etc including disposing off the retrieved debris outside the premises, complete all as specified and as directed.

M&L for coloured Non - skid Ceramic tiles 7 to 8 mm thick (square / rectangular) of approved size, area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white cement mixed with pigments to match with the shade of tiles, over and including 15mm thick screed bed in CM 1:6, complete all as specified and as directed.

All as per item No 13 above but for vertical surfaces such as skirting etc, over and including 10mm thick back coat in CM 1:4.

M & L for coloured Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) of approved size, area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white cement mixed with pigments to match with the shade of tiles, over and including 15mm thick screed bed in CM 1:6, complete all as specified and as directed.

M&L for coloured Glazed ceramic tiles of size 300mmx 450mm , 6 to 7 mm thick on the vertical surfaces such as in skirting / dado etc, set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match with the shade of the tiles, over and including 10mm thick cement mortal backing coat in CM 1:4, complete all as specified and and as directed.

M&L for 18 to 20mm thick Machine cut kota stone slabs of size 590mm x 590mm as in flooring, laid over and including 20mm thick screed in cm 1:6, set, jointed and pointed in neat cement slurry mixed with pigment to match with the shade of the slabs, including rubbing and mirror polishing etc, complete all as specified and as directed

M&L for 18 to 20mm thick machine cut and prepolished kota stone slab as in skirting, landing, risers and treads (single piece stone slabs shall be provided for risers and treads) of the steps (including making 3 groves on the Kota Stone Treads) over and including 15mm thick cement mortar bed in CM 1:4, jointed and pointed with grey cement slurry mixed with pigment to match with the shade of the slab, including moulding / rounding to the edges of the slabs, complete all as specified and as directed.

M&L for 18 to 20mm thick machine cut, pre-polished Black Jet, premium quality, granite stone slab, in skirting, Kitchen platform, dado etc laid over and including 15mm thick CM 1:4 screed bed, jointed with grey cement slurry and pointed with white cement with admixture of pigment to match with the shade of granite stone including rounding / moulding the edges half round, complete all as specified and directed.

Demolition of brick work or rubbled stone masonry including all quoins, arches , pillars etc built in cement mortar including disposing off the retrieved debris outside the premises, complete all as specified and as directed.

M&L for Brickwork with fly ash Bricks, straight or curved on plan exc 6m mean radius, built in Cement morter 1:6, complete all as specified and directed

M&L for brick work with fly ash Bricks, straight or curved on plan to any radius built in CM 1:4, as in half brick thick walls, complete all as specified and as directed.

Taking down cement plaster on brick or stone walls etc. including raking out joints, hacking for key, scrubbing down with water, etc and including removal of debris and rubbish from the site outside the premises, complete all as specified and as directed.

M&L for rendering 15 mm thick in CM (1:6) on the surfaces of brick work or concrete, finsihed even and smooth (without using extra cement), complete all as specified and as directed.

M&L for rendering 15 mm thick in CM (1:4) on brick work or concrete surface finsihed even and smooth (without using extra cement) mixed with water proofing compound as per manufacturer instructions, complete all as specified and as directed. Note:- WPC shall be measured and paid seperately.

Supply only liquid water proofing compound, complete all as specified and as directed.

Demolition of reinforced cement concrete (reinforcement cut as required to facilitate demolition) of any description as in kitchen shelves, cooking platform, lintels, chajja, beams, slabs etc and in any other position, not otherwise specifically provided for including disposing off the retrieved debris outside the premises, complete all as specified and as directed.

Use and waste of formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide for rough finished flat concrete surfaces, complete all as specified and as directed.

Use and waste of formwork to Beams, cantillevers, bressumers, lintels, shelves and similer items for rough finished flat surface of concrete, complete all as specified and as directed.

Use and waste of formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work, not exceeding 200mm thick (horizonal or slopping) for rough finished flat surfaces of concrete, complete all as specified and as directed.

Use and waste formwork to chullah hoods, chajjas, troughs and similer items including edges for rough finished flat surface of concrete, complete all as specified and as directed.

M&L for TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia, or securing with clips etc, complete all as specified and as directed.

M&L TMT bars 8mm dia and over upto and including 10mm dia in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips etc, complete all as specified and as directed.

M&L for reinforced cement concrete (1:11/2:3) type A-1 (using 20 mm graded stone aggrgates) as in Beams, cantilevers, bressumers, lintels over 1.5 metre span, complete all as specified and directed. Note: Reinforcement and Form Work shall be measured and paid for seperately.

M&L for reinforced cement concrete (1:11/2:3) type A-1 (using 20 mm graded stone aggrgates) as in Chajjas, complete all as specified and directed. Note: Reinforcement and Form work shall be measured and paid for seperately.

M&L for reinforced cement concrete (1:11/2:3) type A-1 (using 20 mm graded stone aggrgates) as in slabs supported on walls, beams and and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like, complete all as specified and as directed. Note :- Reinforcement and Form work shall be measured and paid for seperately.

M&L for Pre-cast reinforced cement concrete (1:11/2:3) type A-1 (using 20 mm graded stone aggrgates ) as in landing, cover slabs (for manholes etc), chulla hoods, shelves and similar article with plain faces including form work, complete all as specified and as directed. Note :- Reinforcement shall be measured and paid for seperately.

Demolition of cement concrete (un-reinforced) as in sunken floors etc and of any description & in any position, not otherwise specifically provided for, including disposing off the retrieved debris outside the premises, complete all as specified and as directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings n.exc 15cm thickness (below or above ground level), Complete all as specified and directed.

M&L for factory fabricated Hydraulically machine pressed cement concrete chequered tiles of size 300x300X25mm thick (with grey cement and pigment), set in neat cement slurry including provision of 15mm thick cement screed bedding layer in CM 1:4, tiles joints shall be grouted and immediately after grouting, the joints shall be pointed flush in separate process in CM 1:3 mixed with pigments to match the colour of the Tiles, complete all as specified and directed.

M&L for providing 75mm thick PCC (1:3:6) type C1 (using 20mm graded stone aggregate) as in plinth protection, surface finished even & smooth without using extra cement including provision of 10 mm joints (at an interval of 3 metre and turnings) duly filled with fine sand and bitumen in the ratio of 3:1, complete all as specified and directed.

M&L for cement concrete 1:2:4 type, B1 (using 20 mm graded stone aggregates) as in copings, Chajja, kerbs, roof padding, staging of water tank, for sealing of chases for fixing of pipes upto DB etc, including necessary formwork, weathering, slightly rounded or chamfered angles and throating, complete all as specified and as directed.

M&L for cement concrete 1:3:6 type C-1 (using 20mm graded stone aggregates) as in hold-fast blocks, blocks for fixing lugs, filling of pressed steel chowkhat and the like including necessary form work, complete all as specified and as directed.

M&L for 25mm thick cement concrete (1:2:4) type B-0 (using 12.5mm graded stone aggregates) as in sub-base of the floors, finished fair & even/rough, complete all as specified and as directed.

Taking down chowkats or frames with Wooden/PVC/Flush shutters (without taking off shutter from frames) not exc. 1.5 sqm each, including cutting holes for removing the hold fast etc, also including disposing off the retrieved debris outsite the premises, complete all as specified and as directed.

Taking down chowkats or frames with Wooden/PVC/Flush shutters (without taking off shutter from frames) exc. 1.5 Sqm but n exc 4 Sqm each, including cutting holes for removing the hold fast etc, also including disposing off the debris outsite the premises, complete all as specified and as directed.

S&F factory made 1.25 mm thick pressed steel frame of size 165 X 60 mm for doors with one or more rebates includings necessary provision of lugs, locks strike plate etc, also including application of one shop coat of Zinc Chromate primer, complete all as specified and as directed. Note :- Hinges shall be paid for separately.

S&F Factory made 1.25 mm thick pressed steel frame of size 105 X 60 mm for doors with one or more rebates includings necessary provision of fixing lugs, locks strike plate etc, also including application of one shop coat of Zinc Chromate primer, complete all as specified and as directed. Note:- Hinges shall be paid for seperately.

S&F mild steel work conforming to Fe-290 Gde-E-165 as in hold fasts; wall ties; hooks for hanging fans and similar small articles, complete all as specified and as directed.

S&F Factory made 35mm thick flush shutter solid core construction with block board core and ply wood face panels, commercial type on both sides including provision of 4mm thick 2nd class hard wood edging to the exposed edges of the shutter, complete all as specified and as directed.

M&L for 2nd class hard wood (Hollock/Kalasiris/Brjsal/Gamari) (kiln seasoned and chemically pressure treated) 35 mm thick glazed and skeleton shutters, open rebated and prepared to rceieve glass, gauze,etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass,etc, sizes of members of shutters as specified in SSR Part-1, Section 8, clause 8.24 (a), complete all as specified and as directed.

S&F 200mm long, Aluminium anodised barrel tower bolt of extruded section, complete all as specified and as directed.

All as per item No 52 above, but 150 mm long.

S&F 250mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy, complete all as specified and as directed.

S&F 100mm size butt hinges, heavy weight, cold rolled, mild steel, complete all as specified and as directed.

S & F 75mm size butt hinges, extruded alumium alloy with galvanised mild steel hinge pin, anodised, type C-21, complete all as specified and as directed.

S&F 125 mm size aluminium handle, cast type, anodised, complete all as specified and as directed.

Taking down of steel windows & vents (including taking down of grills/framed guard bars, where occurs); including cutting holes for removing of the lugs etc, also including disposing off the retrieved debris outside the premises, complete all as specified and as directed.

S & F factory made steel windows with side hung shutters including projecting type hinges with steel handle, and peg stay, complete with glazing bars, dovetaild or welded, including application of one shop coat of Zinc Chromate primer, complete all as specified and directed.

All as per item No 59 above but steel window without glazing bars.

S&F Factory made, steel ventilator with top hung shutter including hinges, steel peg stay, including application of one shop coat of Zinc Chromate primer, complete all as specified and directed.

S&F 4mm thick sheet glass of ordinary quality and glazing for Aluminium Joinery or for steel surrounds with & including oil putty, in squares, complete all as specified and as directed.

S&F 3mm thick sheet glass of ordinary quality and glazing for Aluminium Joinery or for steel surrounds with & including oil putty, in squares, complete all as specified and as directed.

S&F 3mm thick Figured glass, pin head type and glazing for Aluminium Joinery or with & including oil putty for steel surrounds, in squares, complete all as specified and as directed.

M&L for the Framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forget into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 290 Gde E-165, complete all as specified and as directed.

S&F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperature 1.40 mm and fixed with and including stainles steel wire staples etc, complete all as specified and as directed.

S&F standard aluminium powder coated section(minimum thickness of powder coating shall be 50micron and colour shall be as approved by the GE) as in frame, shutters for doors, windows / ventilators, Fixed/ Openable / side hung/ sliding two or three track or in any pattern, partitions, kitchen cabinate, kitchen almirah, etc cut to size, jointed with cadmium plated steel screws, including rubber beading or gaskets for fixing glass, provision of hinges, screws, plugs, handle, lock, roller, Nylon ball bearing etc, complete all as specified and directed. Notes:- (i) Weight of Aluminium sections as per actual or as per IS or as per manufacturer, whichever is less, shall only be considered for payment. (ii) The accessories (including Aluminium mongries etc) required to be provided for windows, vents and doors as per directions of Engineer-in-charge shall be provided but weight for the same shall not be considered. (iii) Cost of all the items, accessories & Aluminium mongries required for the entire completion of the work shall be deemed to be included in the quoted rate. However glass panes, wire cloth, lock and prelaminated particle board shall be measured and paid separately under respective items.

M&L for 8/9 mm thick, Prelaminated particle board, interior grade, prelaminated on both sides with decorative choice lamination for aluminium joinery and partitions, complete all as specifiied and directed.

S&F in repairs stainless steel decorative curtain rail of 20 mm bore with wood finishes, complete all as specified and as directed.

S&F Set of two brackets and two funnel caps suitable for the curtain rod to be provided under item No 70 above, complete all as specified and as directed.

S&F double action floor spring, hydraulically regulated made up of minimum 1.25 mm thick alumium alloy sheet foundation box , main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty, complete all as specified and as directed.

S&F Mortice lock, Brass vertical type, 4 levers, size 75 mm, complete all as specifiied and directed.

S &F stainless steel kitchen plate rack of overall approx size 36’’ x 36’’ x 10’’, Cat No –P-348 of Make Prayag or of any other equivalent make as approved by GE, complete all as specifiied and directed.

S&F Factory made Solid PVC Door Frame of size 50mm x47mm made out of 5mm single side prelam PVC sheet & edges will be painted to match with prelam sheet, reinforced with M.S. Square tube, complete all as specified and shown in drawing for SI No. 08097 on Srl Page No. 160 of SSR (Part-II) and as directed.

S&F factory made solid PVC moulded door shutter with wood free EPS, 28 to 30mm thick (Stiles), with 2, 4 or 6 raised panel design with 2mm thick moulded prelam PVC sheet on the front face and 2mm plain colour PVC sheet on back face all as shown on drawing at page No 161 of SSR Part-II, complete all as specified and as directed.

M&L for Preparation of new steel and iron surfaces of any description, over 10 cm in width or girth , not otherwise described and painting with two coats of synthetic enamel paint over a coat of red oxide primer, complete all as specified and as directed.

M&L for Preparation of steel and iron surfaces duly applied with shop coat of primer of any description, over 10 cm in width or girth , not otherwise described and painting with two coats of synthetic enamel paint, complete all as specified and as directed. Note : Cost of application of shop coat of primer not included in the above item.

M&L preparation of old painted surfaces of steel surface of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint, complete all as specified and as directed.

M&L preparing new wooden surfaces of any description, not other wise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified and as directed.

M&L for preparaton of old/new surfaces of wall/ceiling and applying two coats (thickness of both coats minimum 2mm) of Birla/Asian wall care putty, complete all as specified and as directed.

M&L for preparing new surfaces of walls duly applied with wall care Putty and thereafter applying two coats of oil bound distemper, white or any tint as approved, over and including a coat of primer, complete all as specified and directed. Note :- Provision of wall care putty not included in this item.

M&L for complete removal of existing treatment of wall, preparing the new surfaces of walls duly applied with wall care putty and thereafter applying two coats of oil bound distemper, white or any tint as approved, over and including a coat of primer, complete all as specified and directed. Note :- Provision of wall care putty not included in this item.

M&L for preparing new plastered surfaces of walls and applying three coats of white wash, complete all as specified and as directed.

M&L for preparing the old decorated surfaces of walls and applying two coats of white wash, complete all as specified and as directed.

M&L preparing new untreated external surfaces of walls etc and applying two coats of exterior emulsion weather coat paint over & including one coat of primer as per manufacturer instructions, complete all as specified and as directed.

M&L for complete removal of existing treatment from the external surfaces of wall etc, thereafter prepartion the surfaces and applying two coats of exterior emulsion weather coat paint over & including a coat of primer as per manufacturer instructions, complete all as specified and as directed.

Taking down of Aluminium joinery (including chowkat, fittings etc), including taking down of grills/guard bars (where occurs) & cutting holes for removing the hold fasts etc, also including disposing off the debris outside the premises, complete all as specified and as directed.

S&F in repairs PVC valveless, double syphonic action type, flushing cistern, low level of 10 Litres capacity, white, with and including inlet, ball valve, float, 32mm dia flush pipe of polyethylane of low or high density or PVC, flushing bend & handles, also including brackets, suitable for both Indian Type Water Closet & Europeon Type Water Closet & making connections, complete all as specified and as directed.

M&L for rendering 10mm thick in CM 1:3 on concrete surfaces of ceiling/Chajja/Facia of chajja etc, finished even and smooth without using extra cement, complete all as specified and as directed.

M&L for preparing new plastered surfaces of ceiling and applying three coats of white wash, complete all as specified and as directed.

S&F in repairs Vitreous China Wash Down Water closet (Pedestal Pattern) 1st quality, white (excluding flushing cistern & flush pipe) including plastic water closet seat white, closed pattern with flat bottom and cover and mild steel CP or aluminised huiging device, making connections, the EWC Pan shall of make JAQUAR : Cat No. CNS-WHT-553SN or equivalent Cat No. of other make as mentioned in Appendix 'B' of the Particular Specifications as approved by the GE, complete all as specified and as directed.

S&F in repairs, vitreous china, 1st quality, squatting pan, Orrisa pattern of approx size 260 x 440 x 580mm, white with integral foot rests, 'P' trap including making connection to trap, flush pipe, anti-syphonage pipe etc, the WC Pan shall of make JAQUAR : Cat No. CNS-WHT-OP01 or equivalent Cat No. of other make as mentioned in Appendix 'B' of the Particular Specifications as approved by the GE, complete all as specified and as directed.

S&F in repair vitreous china wash basin (Make JAQUAR : Cat No. SLS-WHT-6801 or equivalent of other make as mentioned in Appendix 'B' of the Particular Specifications as approved by the GE), 1st quality, white, flat back, approx size 575x465x195 mm, excluding taps but including 32 mm bore brass chromium plated waste fittings, 32mm bore PVC waste pipe, MS brackets, complete all as specified and as directed.

S&F in repair sink made of 0.80 mm thick sheet of stainless steel (Bronze range super steel 204 : Matt) for kitchen or laboratory with and including plugs, washers, 40mm bore brass chromium plated waste fittings, 40mm bore PVC waste pipe, also including bedding in cement mortar 1:3 on dwarf wall or including providing mild steel cantilever brackets and connecting union to pipe, overall size 460mm x 535mm x 203mm with bowl size 460mmx 394mm x 203mm of Cat No 920-DM of Make- Prayag or equivalent of make as mentioned in Appx “B” of particular Specifications as approved by GE, complete all as specified and as directed.

S&F in repairs bib tap, fancy type, cast copper alloy, chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or brass ferrule of 15 mm bore, complete all as specified and as directed. (Make : ESSCO : Cat No. SQT-511KN or equivalent of other make as mentioned in Appendix 'B' of the Particular Specifications as approved by the GE).

S&F in repairs stop valves, fancy type, cast copper alloy, chromium plated with long shank and cup (concealed type), screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions of 15 mm bore, complete all as specified and as directed (Stop valves shall be of make- ESSCO : Cat No. SQT-514AKN or equivalent of other make as mentioned in Appendix 'B' of the Particular Specifications as approved by the GE).

S&F in repairs stop valves, fancy type, cast copper alloy, chromium plated, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions of 15 mm bore, complete all as specified and as directed. (Stop valve shall of make ESSCO : Cat No. SQT-513AKN/SQT-513BKN or equivalent of other make as mentioned in Appendix 'B' of the Particular Specifications as approved by the GE).

S&F in repairs angle valves, fancy type, cast copper alloy, chromium plated, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions of 15 mm bore, complete all as specified and as directed. (Stop valve shall of make ESSCO : Cat No. SQT-526KN or equivalent of other make as mentioned in Appendix 'B' of the Particular Specifications as approved by the GE).

S&F in repairs stop valves, fancy type, cast copper alloy, chromium plated with long shank and cup (concealed type), screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions of 20 mm bore, complete all as specified and as directed. (Stop valve shall of make ESSCO : Cat No. SQT-514CKN or equivalent of other make as mentioned in Appendix 'B' of the Particular Specifications as approved by the GE).

S&F in repairs Pillar taps with Aerator, fancy type, cast copper alloy, with long swan neck , chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe of 15mm bore, complete all as specified and as directed (Pillar tap shall of make ESSCO : Cat No. SQT-508KN or equivalent of other make as mentioned in Appendix 'B' of the Particular Specifications as approved by the GE).

S&F in repair Self-closing taps, cast copper alloy, chro-mium plated, screwed for iron pipe 15 mm bore, complete all as specified and as directed .

S&F in repairs 15mm size PVC connection of 450 mm length including brass nuts, complete all as specified and as directed.

S&F in repairs tubular towel rail, 20mm dia, D type, brass chrormium plated, 600mm long between flanges, complete all as specified and as directed. (Towel Rail shall be of make- Prayag : Cat No. BA-01 or equivalent of other make as mentioned in Appendix 'B' of the Particular Specifications as approved by the GE).

S&F in repairs Towel Ring of brass Chromium plated, complete all as specified and as directed (The Towel Ring shall be of make- Prayag : Cat No. BA-02 or equivalent of other make as mentioned in Appendix 'B' of the Particular Specifications as approved by the GE).

S & F in repair Shelf of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats (minimum weight 300gms) complete all as specified and directed. (The shelf shall be of make- Prayag : Cat No. 191 or equivalent Cat No. of other make as mentioned in Appendix 'B' of the Particular Specifications as approved by the GE).

S & F in repairs Soap Dish of PTMT with and including chromium plated brass screws, complete all as specified and as directed (Soap Dish shall be of make- Prayag : Cat No. 1951 or equivalent Cat No. of other make as mentioned in Appendix 'B' of the Particular Specifications as approved by the GE).

S&F in repairs brass chromium plated shower roses, 125 mm size with or without swivel joints including shower Arm, also including fixing to 15mm bore steel pipe or union, complete all as specified and as directed (The Shower Rose and Shower Arm shall be of make- Prayag : Cat No. BOS-11 and BOS-48 respectively or equivalent of other make as mentioned in Appendix 'B' of the Particular Specifications as approved by the GE).

Taking down 15mm bore steel tubing & connections, complete all as specified and as directed.

All as per item No 110 above but 20 mm bore

All as per item No 110 above but 25 mm bore

Fixing only of 15mm bore GI tubing, medium grade with provision of new G.I. fittings as required and fixing accessories in new or old position (walls,ceiling, floor etc) including testing, complete all as specified and directed.

All as item No 113 herein before but 20mm bore.

All as item No 113 herein before but 25mm bore.

S&F 15mm bore medium grade, galvanized steel tubing (including in short lengths) with and including all fittings, fixed partly on the surfaces and partly concealed in the walls & ceiling or laid in floors, also including cutting chases of the required size and making good the same after fixing of the pipes in CM 1:3 to match with the adjoining surfaces, complete all as specified and as directed.

All as per item no 116 above but 20 mm bore pipes.

All as per item no 116 above but 25 mm bore pipes.

S&F in repairs for 100 mm bore out let cast iron floor trap with and including grating, also including jointing to waste pipe and provision of cement concrete type B-1 (1:2:4) block of required size for fixing, complete all as specified and as directed.

S&F in repairs PVC (SWR) gully trap 125/110 mm, setting and jointing with and including solvent cement, also including provision of cement conconrete type B-1 (1:2:4) block of required size for fixing, complete all as specified and as directed.

S & F in repairs 110 mm bore uPVC (SWR) soil, waste, ventilating, rain water pipe type 'A', single socketed, (ISI Marked) in any length with and including ruber ring joints, complete fixed to wall with necessary PVC standard stay clamps etc, complete all as specified and directed. Note :- Quoted rates shall also be deemed to include for cutting of the holes where required/ directed and making good the same in CM 1:3 to match with the existing surfaces.

S&F in repairs uPVC vent cowl for 110mm bore uPVC (SWR) pipe with and including rubber ring joints, complete all as specified and directed.

S&F in repairs 110mm bore uPVC (SWR), junction single (Single T), equal or unequal with and including rubber ring joints, complete all as specified and directed

S&F 110mm bore uPVC (SWR) bends (any radius), with and including rubber ring joints, complete all as specified and directed.

S&F in repairs 100 mm bore Cast iron soil, waste and vent pipes(spun pipes), in any length with ears, with and including cement joints, laid in trenches or in floors or fixed to wall vertically (also including suitable mild steel clamps for fixing of the pipes with the wall etc), complete all as specified and as directed. Note:- Excavation and earth work shall be measured and paid for separetly.

S&F in repairs 100mm bore cast iron Bends (any radius), diminishing pieces or tapers (larger bore measured), fitted with & including oval access door, complete all as specified and as directed.

S&F in repairs cast iron Branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches for 100mm bore pipe, complete all as specified and as directed.

Dismantling water tanks exc 250 litres but not exc 500 litres capacity including disconnecting the connections, complete all as specified and as directed.

S&F rotational moulded polyethylene water storage tank 1000ltrs capacity, ISI marked, (cylindrical vertical type double-layered) with closed top including inlet,outlet and wash out holes, provision of G.I Fittings for fixing of the inlet, outlet and washout pipes, hoisted in position, complete all as specified and as directed.

S&F in repairs Ball valves, high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic ball, screwed for iron pipe of 20mm bore (Minimum weight 210 grms), complete all as specified and as directed (The ball valves shall be of make- Prayag : Cat No. 152 or equivalent of other make as mentioned in Appendix 'B' of the Particular Specifications as approved by the GE).

S&F Hard drawn steel wire fabric in available size weight not exc 4.00 Kg /sqm for the tank caging etc including welding, riveting, framing etc, complete all as specified and as directed.

Excavating in trenches n.exc. 1.50m wide and n.exc 1.50m in depth for foundation, laying of cable, pipe etc and getting out in soft/loose soil, complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm thick with soil etc complete all as specified and directed

Removing excavated material to a distance not exc 50.00 mtr and depositng where directed at a level n.exc 1.5m above the stating point, complete all as specified and as directed.

Demolition and breaking up 150mm bore SGSW drain pipes, set in cement mortar, complete all as specified and directed. Note:- Excavation and Earth Work shall be measured and paid for separately.

M&L for cement concrete 1:3:6 type C-2 using 40mm graded stone aggregates for 150 mm bore pipes as in bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested, complete all as specified and as directed.

M&L for 150 mm bore SGSW pipe, grade 'A', laid in trenches including jointing with cement mortar, complete all as specified and directed. Note:- Excavation & Earth Work, PCC bed & haunching shall be measured & paid for separately.

Disludging gully trap by taking out sludge & foreign materials, excavating a pit of appropriate size & depositing sludge in the pit and covering with 30 cm thick layer of soil to cover the sludge including removing surplus soil where directed by Engineer - in - Charge.

All as per item no 138 above but for manholes of depth upto 100cm.

S&F in repairs Salt Glazed Stone Ware Gully Trap, square or round mouthed, 150x150mm (type P or Q or S), setting and jointing to drains with cement mortar 1:1 and provision of cement concrete type B-1 (1:2:4) block of required size for fixing, including necessary excavation & earth work etc, complete all as specified and as directed.

M&L for providing Plain Cement Concrete (1:3:6) type C1 (using 20mm graded stone aggregate) as in surfaces channel and drains including necessary form work, complete all as specified and as directed.

Extra for forming fair finished drain or channel 30 cm inner girth using extra cement including forms, moulds mitred/stopped ends etc, complete all as specified and as directed.

M&L for Cutting salt-glazed stoneware drain pipe in position, including jointing socket end of new pipe to same with packed spun yarn and cement mortar 1:1 etc, complete all as specified and as directed.

Surface dressing n exec 15 cm deep and and disposal of the debris etc outside the premises, complete all as specified and as directed.

M&L for 75mm thick cement concrete (1:4:8) type D-2 (using 40mm graded stone aggregates) as in sub base of flooring, complete all as specified and as directed.

M&L for Sand cushioning below the paver block etc including spreading and levelling etc, complete all as specified and directed.

M&L for 60mm thick Factory Fabricated Machine pressed precast concrete reinforced with glass fibre interlocking paver blocks confirming to IS 15658-2006, M-35 Grade, glossy finished, vibro compacted (size, shape and colour as approved by the GE) with grey cement and pigments, complete all as specified and as directed.

M&L for Brickwork with fly ash Bricks, straight or curved on plan, exc 6m mean radius, built in Cement morter 1:4, complete all as specified and directed

M&L for cement concrete 1:4:8 type D-2 (using 40mm graded brick aggregate) as in foundation concrete and mass filling, complete all as specified and as directed.

M&L for hardcore of broken stone or boulders of gauge n exc. 63 mm, deposited, spread & levelled in layers n exc. 15 cm thick, watered & rammed to a true surface, complete all as specified & as directed.

S&F in repairs, vitreous china urinal, 1st quality, Half Stall Type, white (excluding flushing cistern, flush pipe) but with & including gratings, union for discharge pipe, also including provision of PVC waste pipe and all the fixing accessories, complete all as specified and directed. (The urinal shall be of make- JAQUAR : Cat No. URS-WHT-13257 or equivalent of other makes as mentioned in Appendix 'B' of the Particular Specifications as approved by the GE).

Excavation in post holes and/or similar holes each not exceeding 0.50 Cum in soft/loose soil, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around in layers not exceeding 25cm, complete all as specified and as directed.

M & L for Cement concrete (1:3:6) type C2 (using 40 mm graded stone aggregates) as in PCC blocks for fixing fencing posts, foundation filling and mass concrete, complete all as specified and as directed.

M&L for mild steel comprising of the angle iron, flat iron etc using steel conforming to Fe-290 Gde E-165 as in posts and struts in fencing inclluding cutting tops to shape as diected, drilling holes, notching for wire etc, including necessary bolting/ riveting and embeding in concrete and similar work, complete all as specified and as directed.

S&F Mild steel bars 10mm dia round bars and over, cut to length, bent to shape required, including cranking, bending, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips conforming to Fe 290 (Gde - E-165) for holding the chain link fencing in the position etc, complete all as specified and as directed.

Dismantling fencing posts or struts (steel or RCC), any section including taking out embedded portion by demolition of PCC block foundation and making good the disturbed ground, also including dismantling of the fencing wire/ mesh/ chain Link Fencing of any type and disposing off the debris outside the premises, complete all as specified and directed. Note :- For payment purpose, length of posts/struts as dismatnled shall only be considered.

Supply only of chain link fencing made of mild steel galvanised wire and size of mess as per site requirement, complete all as specified and as directed.

Fixing only chain link fencing of any size including line wires, any mess, size and type, to any type of standards, rails, straining bolts etc, inclding provision of binding wire, complete all as specified and as directed.

S&F Mild steel screw bolts (machine made) (diameter of neck 11 to 15 mm) with hexagonal or square heads at one end or screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, length of bolt exc 05 cm but n. exc 10 cm long, complete all as specified and as directed.

M&L for makrana white marble 18-20mm thick as in strips to be provided in the floor, laid over & including 20mm thick bedding layer in CM 1:6, also including grinding and polishing, complete all as specified and as directed.

Taking down carefully existing aluminium/copper point wiring (light / fan / socket or power point) complete, with all fittings such as switch socket combination, switches, sockets, regulator, ceiling rose, utility light fittings and lamp holders etc and making good the disturbed surfaces of walls, roof and floor etc to match with the existing specification, complete all as specified and as directed.

Taking down existing unserviceable distribution board, switch fuse unit, enclosure for MCB / DB (inclusive of MCBs etc of any type and capacity) and making good the disturbed surfaces all as specified and as directed.

Taking down existing unserviceable submain wiring (including conduit /casing -caping), any size and making good the disturbed surfaces to match with the adjoining surfaces, complete all as specified and as directed.

Material and labour for point wiring for one light and/or one fan point controlled by 1 one way switch with 1.5 Sqmm PVC insulated unsheathed single core multi-stranded copper conductor (FRLS) cable 1100 Volts grade drawn through and including rigid non metallic PVC concealed conduit (medium grade) of suitable dia, (also including conduit fittings & PVC Junction boxes etc, along with 1.5 sqmm continuous PVC insulated unsheathed single core multi-stranded copper conductor (FRLS) cable for earth continuity wire, connected to earth dolly and to be terminated in and including factory made pressed steel sunken boxes (Having wall thickness not less than 1.22 mm for boxes upto a size of 200 mmX300 mm and beyond that the wall thickness shall be not less than 1.63 mm), concealed type with and including 3mm thick bakelite sheet cover for mounting switches, sockets, fan regulators etc, testing on completion also including cutting chases for concealed conduit, steel boxes etc, pinning in, making good the surfaces in CM 1:3 to match with the adjoining surfaces, complete all as specified and as directed.

All as per Item No 164 above but for one switch socket outlet, 5 Amp on independent board all as specified and as directed.

All as per item No 164 here-in-before but for one socket with other switches on the same board, complete all as specified and as directed.

All as per item No 164 here-in-before but for one15 Amp switch socket outlet, independent with 2.5 Sqmm single core multi-stranded copper conductor cable (FRLS) along with 2.5 sqmm continuous PVC insulated unsheathed single core multi-stranded copper conductor (FRLS) cable for earth continuity wire, complete all as specified and as directed.

All as per Item No 164 here-in-before but for one AC/Geyser, independent with 4.00 Sqmm single core multi-stranded copper conductor cable (FRLS) along with 4.00 sqmm continuous PVC insulated unsheathed single core multi-stranded copper conductor (FRLS) cable for earth continuity wire, complete all as specified and as directed.

Supply and fixing switch piano flush type, single pole, one way, 5 amps, complete all as specified and as directed.

Supply and fixing switch socket combination, 2 in 1, 5 Amp, flush type, complete all as specified and as directed.

Supply and fixing switch socket combination, 2 in 1, 3 pin, 5 and 15 amp, flush type, universal, complete all as specified and as directed.

Supply and fixing ceiling rose, 3 phase /PVC/Polycarbonate, isolated body, complete all as specified and as directed.

Supply and fix electronic fan regulator, flush type, 5 step not less than 100 watt, complete all as specified and directed.

Supply and fix LED tube light fitting 1 X 20 Watts (4 Ft) 240 Volts, Ultra bright polycarbonate LED Tubelight with very high efficiency suited for installation in & including T8 tubelight with G13 lamp holders, complete with and including all accessories, internally pre-wired and including making connection by providing 3 core 1.5 Sqmm PVC insulated stranded copper conductor cable, complete all as specified and directed. Make and Cat No of T-8 Tubelight : HAVELLs Cat No PHOTONULTRAE2.01213T8SSTL20WLED865SPC or equivalent of make Crompton/PHILIPS/BAJAJ as approved by the GE. Make and Cat No of T8 Tube Light Fittings : HAVELLs Cat No Regal Batten T8UPTO1X22WSSBSWH or equivalent of make Crompton/PHILIPS/BAJAJ as approved by the GE.

S&F in repairs Building Security light, presure die-cast housing with individual LEDs as light source and Lens embedded PC cover having TOP opening, separate driver compartment with IP 66 protection and impact resistance of IK-07, make BAJAJ : Cat No. BRLEP15WLED or equivalent of make HAVELLS/PHILIPS/CROMPTON as approved by the GE and provision of copper conducor cable for connection, complete all as specified and directed.

Supply and Fix Lamp holder, PVC/Polycarbonate type with back plate, complete all as specified and directed.

S&F ceiling fan, 5 star rating, ISI marked, white in colour,1200 mm sweep, 230V, Single Phase, complete with accessories, MS hook made out of mild steel flat iron of size 25 x 5mm of the rquired length for hanging of ceiling Fan, also making connection with and including copper conductor cable from ceiling rose to fan, also including taking down of existing Fan and depositing the same in MES store yard of GE, complete all as specified and as directed, Make : Usha model TECHNIXPLUS ISI marked or Equivalent of make Havells/Bajaj as approved by the GE.

S&F Exhaust fan, 380mm sweep, 230V, single phase, metal body complete with and including accessories, louvers, anchoring bolts, nuts, washers, making opening for fixing of the exhaust fan & making good the surfaces of the openings with CM 1:3 to match with the existing surfaces & provision of PVC copper conductor cable for making connection with ceiling rose, also including taking down of existing fan & depositing the same in MES store yard of GE, complete all as specified and directed, Make- USHA model No TURBO HDEF900RPM ISI GREY or equivalent model of make CG/HAVELLS/Bajaj/Orient as approved by the GE.

S&F in repairs electric storage heater of 25 Litre capacity, vertical type with ABS covered outer body, 3 mm thick EPAC (Engineered Polymer Anti Corrosion) coated inner tank to suit any kind of water, interchangeable coloured (Red& green) panel, vitreous enamel coated heating element for long life, adjustable capillary thermostat for temperature regulation, multifunctional safety valve including hot & cold water CP flexible pipe etc and fixing arrangement for mounting on wall, complete all as specified and directed, Make : USHA Model No. MYSTY or equivalent of make CG/Jaquar/Bajaj as approved by the GE. Note : The old electric storage heaters shall be the property of the deptt and the same shall be deposited by the contractor in MES store yard.

S&F PVC body exhaust fan, 250mm sweep, 230 volts, AC, single phase, complete with & including accessories, louver shutters, provision of PVC copper conductor cable for making connection from existing ceiling rose, making opening for fixing of the exhaust fan & making good the surfaces of the opening with CM 1:3 to match with the existing surfaces, also including taking down of existing fan & depositing the same in MES store yard of GE, complete all as specified and directed. Make : USHA Model No CRISP AIR EF Pearl white or equivalent model of make CG/HAVELLS/BAJAJ/ORIENT as approved by GE.

Supply and fixing sheet metal enclosure for MCBs DBs, Double Doors, phosphatised, Powder coated , single pole and neutral (SPN), 240 Volt , 8 Ways with and including common bus bar at incoming end, also cutting nitches/opening in the wall for accommodating the enclosures, plastering to the back & sides of nitches/surfaces of opening in CM 1:3 & making good the damaged surfaces to match with the adjoining surfaces, complete all as specified and directed.

Supply and fixing sheet metal enclosure for MCBs DBs, Double Doors, phosphatised, Powder coated , triple pole and neutral (TPN), 415 Volt , 8 Ways with and including common bus bar at incoming end, also cutting nitches/opening in the wall for accommodating the enclosures, plastering to the back & sides of nitches/surfaces of opening in CM 1:3 & making good the damaged surfaces to match with the adjoining surfaces, complete all as specified and directed.

Supply and fixing sheet metal enclosure for MCBs DBs, Double Doors, phosphatised, Powder coated , triple pole and neutral (TPN), 415 Volt , 6 Ways with and including common bus bar at incoming end, also cutting nitches/opening in the wall for accommodating the enclosures, plastering to the back & sides of nitches/surfaces of opening in CM 1:3 & making good the damaged surfaces to match with the adjoining surfaces, complete all as specified and directed.

Supply and fixing MCB, SPN, C series, 10kA ruputring capacity, 20 to 32 Amps, 240 Volts, complete all as specified and as directed.

S&F MCB, 'C' Series, Four Pole, 40 to 63 Amp, 415 Volts, reputring capacity 10 KA, complete all as specified and directed.

S & F MCB, 'C' Series, Single Pole, 240 volts, 6 to 32 Amps, ruputring breaking capacity 10KA, complete all as specified and directed.

S&F street light bracket made out of 32 mm bore GI Light grade pipe 1.00 M long bent to the shape as required for steet light fittings pronded with two pairs of MS Flat Iron 50mm x 6mm clamps of required shape with nuts, bolts and washers suitable for steel tubular pole including painting of mild steel flat iron surfaces with two coats of synthetic enamel paint over a coat of red oxide primer complete including taking down of unserviceable one, complete all as specified and directed.

Material and labour for galvanized iron tubing 50mm bore light grade with all fittings for protection of cable, laid in trenches/ along poles /wall/floor incl necessary clamps, bolts/nuts, complete all as specified and as directed. Note:- Excavation and earth work shall be measured and paid separately.

Materials and labour for earthing complete with galvanised earth plate electrode 60cm x 60cm x 6mm thick burried directly in ground (earth pit not less than 2.25 metre below normal ground level with top edge of the plate not less than 1.50 metre below normal ground level connected to galvanised lead lead wire 4.0 mm dia by means of bolts, nuts and washers and check nuts of galvanised iron or steel GI earth wire protected by 15mm bore light grade galvanised iron pipe including of 20 mm dia medium grade GI water tubing sheet metal 4mm wire mash funnel, charcoal or coke and common salt in paint and testing on completion as shown on electrical plate No.5 ofm SSR Part-I. including taking out unserviceable one, complete all as specified and directed.

Supplying, laying, jointing and testing XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cable (Heavy duty) with stranded aluminium conductor 1100 volts grade, cross sectional area 16 Sqmm 4 core, in trenches /along poles/on wall etc, complete all as specified and as directed Note For item No 190 : Excavation and earth work, sand cushioning, protection covers shall be measured and paid for separately.

Material and labour for sand cushioning for protection of underground cable consolidated and compacted with clean dry sand all as specified and as directed (Compacted thickness shall only be measured and paid)

Material and labour for well burnt Sub class 'B', old size bricks, best quality locally available laid flat, dry in trenches for cable protection, complete all as specified and as directed.

Material and labour for sub main wiring with 2 run of single core PVC insulated (unsheathed) multi stranded copper conductor FRLS cable of size 2.50 sqmm and one single core PVC insulated (unsheathed) multi stranded copper conductor FRLS cable of size 2.50 sqmm as in continuous earth wire drawn into and including concealed PVC conduit, medium grade of 20 mm bore complete with fittings, PVC Junction Boxes, fixings accessories, also including cutting chases, pinning in, making good to facing and pointing in using cement mortar 1:3 and making good disturbed surfaces to match with the adjoining surfaces, complete all as specified and as directed. Note for Item No 193 & 194:- For payment purposes, 2 runs of main cable (each of 1RM), 1 run of earth continuity cable (1RM) and one run of conduit (1RM), all together shall be considered as "1RM".

M & L for sub main wiring with 2 run of single core FRLS PVC insulated & unsheathed multistranded copper conductor of nominal cross sectional area 6.0 sqmm alongwith one run of FRLS PVC insulated & unsheathed multistranded copper conductor of nominal cross sectional area 6.0 sqmm as earth continuity conductor drawn through and including PVC concealed conduit, medium grade, 25mm bore complete with fittings, PVC Junction Boxes, fixing accessories, also including cutting chases, pinning in, making good to facing and pointing in using cement mortar 1:3 and making good disturbed surfaces to match with the adjoining surfaces, complete all as specified and directed.

Taking down unserviceable underground cable of any size from the trenches, along floors, walls, pole etc, complete all as specified and directed (Note:- Excavation & Earth work shall be measured & paid for separately)

Supply and fixing in repairs Single pole and neutral enclosure with & including a two pin and earth plug and socket, also with and including one number single pole, MCB, 20 Amps, 240 volts, 10 KA ruputring capacity, complete all as directed and specified.

M/S JANATA CONSTRUCTION

Prahalad Rai

M/S G D CONSTRUCTION