Construction of Community Skill Development-Cum-Traning Centre at Vill-Pathalgada, Panchayat-Singhani, Block-Pathalgada, Distt.-Chatra.

Sub Distribution Panel Fhe SDB L&P in Electrical room shall consists of: INCOMER Main Incomer 100 amps TPN MCCB (35KA) terminals suitable to receive 1 x 3.5 x 3S sq. mm XLPE AL.AR. cable connection on one side and Busbar connection on the other side. BUSBARS 150 Amps TPN busbar, chamber of suitable length with aluminium busbars. All busbars and interconnections shall be of suitable size aluminium strips current density of aluminium shall not be more than 0.8 Amns/ so.mm. INDICATING PANEL 3 nos phase indicating lamps each backed up with MCB and switch shall be provided for incomer. Provide Intelligent Panel Meter - Scheinder -Model No-EM- 6400NG (96 mm x 96 mm) covering 25 electrical parameters with RS 485 Port for incomming feeder. OUTGOINGS 4 Nos. 63 A 4P MCB (10 kA) terminals suitable to receive cable on one side and wire connection to Bus bars.. 1 Nos. 63 A DP MCB (10 kA) terminale suitable to receive cable on one side and wire connection to Bus bars.. SDB L&P as described above and specifications complete.

SUPPLY OF LIGHTING FIXTURES & FANS Supply of the following Lightning fixtures including lamps at site. Rate shall include all taxes and duties, transportation etc. complete. (4000K) (Samples of all light fixtures to be submitted to the client for approval prior to procurement of fixtures) Note: All Light Fixtures shall be with H.F electronic ballast (THD less than 11% and P.F.0.95) supply, installation, testing & commissioning of Surface mounted Linear type 4ft 18W Led fitting delivering an initial lamp lumen of 2000 lumens & the luminaire shall be with system efficacy ≥ 100 Im/W. Housing: Polycarbonate . lP20 , Optics: Polycarbonate Diffuser. The operating CCT shall be 6500K with CRI of ≥ 80. The luminaire shall be with BIS Registered electronic driver with input voltage range of 150 to 270V , THD ≥ 20% & PF ≥0.95. The LED Driver shall be easily avaiable in India for repair and service. The LED shall be SMD type. Luminaire shall have minimum surge protection of 2KV.The luminaire shall be with following certifications: LM79 & LM80 issued by LED manufacture along with Photo Biological Safety Standard. Wipro Cat No.: LL20-2021-xxx-6S NE

Supply, installation, testing & commissioning of Surface mounted Linear type 2ft 10W Led fitting delivering an initial lamp lumen of 2000 lumens & the luminaire shall be with system efficacy ≥ 100 Im/W. Housing: Polycarbonate . IP20 , Optics: Polycarbonate Diffuser. The operating CCT shall be 6500K with CRI of ≥ 80. The luminaire shall be with BIS Registered electronic driver with input voltage range of 150 to 270V , THD ≤ 20% & PF ≥ 0.95. The LED Driver shall be easily avaiable in India for repair and service. The LED shall be SMD type. Luminaire shall have minimum surge protection of 2KV. The luminaire shall be with following certifications: LM79 & LM80 issued by LED manufacture along with Photo Biological Safety Standard Wipro Cat No.: LL20-2021-xxx-65

LED 1 X 10 W ( 3100 lumens ) ( 170X170mm) Surface MOUNTED LUMINAIRE with 2KV surge protection, making earthing conection complete to be recessed in false ceiling with all necessary hardwares, hanging - die cast frame arrangement, chains, hook etc. complete. (WIPRO LED LD81-101-XXX-60-SM or Equivalent Philips / Havells)

Supply of 9” dia 1 phase exhaust fan. 1400 RPM

CABLE WORK Supply and laying, effecting proper connections, testing & commissioning of the following sizes of 1.1 KV armoured XLPE unarmoured Cross licked polyethylene insulated, PVC sheathed (XLPE), conforming to IS: 7098 (Part-1)- 1988 ( 90 deg C) aluminium /copper conductor cables conforming to IS : 1554 and IS 694 for Flexible copper cable Part I - 1976 with latest amendments laid over MS supports in existing RCC ducts/ laid in ground /Iaid on Cable Trays including clamping the cables to sup-ports in an approved manner as required complete with all accessories. AII cables shall have thermo setting insulation XLPE and low emission of smoke and corrosive gas when affected by fire 4c x 16 sq. mm armoured XLPE insulated aluminium conductor cable

Add GST @ 18%

Add Labour Cess @ 18%

Percentage BoQ

BoQ_Ver3.0

Bidder Name :

PRICE SCHEDULE (This BOQ template must not be modified/replaced by the bidder and the same should be uploaded after filling the relevent columns, else the bidder is liable to be rejected for this tender. Bidders are allowed to enter the Bidder Name and Values only )

NUMBER #

EXCAVATION AND EARTH WORK Earthwork in excavation in foundation trenches in ordinary soil ( vide classification of soil item -A) and disposal of excavated earth as obtained to a distance upto 50 M. including all lifts, levelling,ramming the foundation trenches, removing roots of trees, shurbs all complete as per approved design, building specification and direction of E/I

Filling in foundation trenches and plinth in layers not exceeding 150mm thick well watered ,rammed , fully compacted and fined dressed with earth obtained from excavation of foundation trenches within a lead of 50m and lift of 1.5m all complete as per building specification and direction of E/I

Filling in plinth with sand under floors including watering, ramming, consolidating and dressing complete.

Extra for brick work with best available local bricks in superstructure above plinth

Providing 75mm thick reinforced designation 75A Brick Work in Cement Mortar (1:4) in Superstructure..do..do…all complete job.

providing PCC M-75 wrth nominal mix of (1:4:8) in foundation with approved quality of stone metal grade - lll (50 mm to 25 mm )' size clean coarse sand-do-1:4:8 ( 1 cement : 4 coarse sand : 8 graded stone aggregate 40mm nominal size)

Providing and laying damp proof course 50mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 12.5 mm nominal size)

Making plinth protection 50 mm thick of cement concrete 1:3:6 (1 cement:3 Coarse sand:6 graded stone aggregate 20 mm nominal; size over 75 mm bed of dry brick ballast 40 mm nominal size well rammed and considered and grouted with fine sand including finishing top smooth.

Providing R C.C M 200 wiih nominal mix of (1 :1.5:3 )in foundation and plinth with approved quality of stone-do-M20 (1 cement : 1.5 coarse samd : 3 stone aggregate 20mm nominal size)

Providing R C.C M 200 wiih nominal mix of (1 :1.5:3 )in columns with -do-All work above plinth level upto V levels

Providing R C.C M 200 wiih nominal mix of (1 :1.5:3 )in roof slab with -do-a. M20 (1 cement : 1.5 coarse sand : 3 stone aggregate 20mm nominal size).

Centering and shuttering including strutting, propping etc. and removal of form for:Foundations, footings, bases of columns, etc. for mass concrete

Columns, Pillars, Piers, Abutments, Posts and Struts.

Lintels, beams, plinth beams, girders, bressumers and cantilevers

Suspended floors, roofs, landings, balconies and access platform.

Providing Tor steel reinforcement of 10mm.,12mm & 16 mm dia bars as per approved design and drawing -do- -do-B) 12mm (TMT coil fe-500)(only valid for sale and tata steel JSPL and Vizag steel

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. RAILING WORK

Supplying and fixing 35mm thick solid core type decorative flush door

Supplying and fixing Choukhats in local wood

Supplying Fitting and fixing good quality local wood in members like pillar, pilattes etc- For Railing

Providing and fixing 40 x 5 mm flat iron hold fasts 400 mm long including fixing to frame with 10 mm dia bolts, nuts and wooden plugs and embedding in cement concrete block 300 x 100 x 150 mm in 1 : 3 : 6 (1 cement : 3 sand : 6 hard stone chips 20 mm nominal size).

Providing and fixing aluminum handles anodised transparent or dyed to required color or shade with necessary screws etc complete.100 mm HANDLE WITH PLATE

Providing and fixing aluminum Tower bolts anodized or transparent or dyed to required color or shade with necessary screws etc complete.250 mm tower bolt

Providing and fixing aluminum sliding door bolts anodised transparent or dyed to required color or shade with nuts and screws etc complete.a) 250 x 16 mm

Providing and fixing aluminium floor door stopper anodised ( anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour and shade with necessary screws, etc. complete.a) Twin rubber stoper (Except Toilet doors)-D2

Supplying & fixing 30 mm thick solid core type non decorative double leaf 1/3 rd glazed flush shutter in windows..do..

Providing and laying Rectified glazed floor tiles 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in all colours, shades, except White, Ivory, Grey, Fume Red Brown laid on 20mm thick bed of Cement Mortar 1:4 (1 Cement : 4 Coarse sand) including pointing the joints with white cement and matching pigments etc., complete.For Toilet Flooring

Providing and laying double charged vitrified floor tiles in different sizes (thickness to be specified by manufacturer with water absorption less than 0.08% and confirming to IS 15622 of approval make in all colors and shades laying on 20mm thick cement mortar (1 cement 4 mortar) joining with cement slurry @3.5kg/sqm including grouting the joints with white cement and matching pigments complete sie of 600x600mm

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm,including pointing in white cement mixed with pigment of matching shade complete.

Stone work (machine cut edges) for wall liningetc. (veneer work) upto 10 m height, backing filled with a grout of average thick cement mortar (1:3) including pointing in white cement mortar (1:2)( 1white cement : 2 stone dust) with an admixture of pigment matching the stone shade: ( to be secured to the backingand the sides by means of cramps and pins which shall be paid for separately) : Red sand stone - exposed face fine dressed with rough backing 30mm thick

Providing and laying gang saw cut 18 mm thick, mirror polished pre moulded and pre polished machine cut granite stone of required size and shape of approved shade, colour and texture in footpath, flooring cut granite stone of required size and shape of approved shade, colour and texture in footpath, flooring in road side plazas and similar locations, laid over 20mm thick base of cement mortar 1:4 (1cement : 4 coarse sand) including grouting the joints with white cement mixed with matching pigment, epoxy touch ups etc. complete as per direction of Engineer-in-Charge. 16.86.1 With granite stone of area less than 0.50 sqm.

Providing and laying vitrified Cool Roof tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 154557-2007 / 15013006, of approved make, in all colours and shades,laid on 20mm thick cement mortar 1:4 (1 cement :4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc. Its solar reflective Index ( SRI ) value should be above 78. complete. Size of Tile 300x300 mm x10 mm thick.

Providing 12mm. cement plaster (1:4)with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water,scaffolding taxes and royalty all complete as per building specification and direction of E/|.Providing 12mm. Thick cement plaster (1:6) -do-

6mm cement plaster to ceiling 1:4

Providing and applying white cement based putty of average thickness 1mm of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Wall painting (two or coats) with plastic emulsion paint of approved brand and manufacture on new work to give an even shade.

Applying priming coat with ready mixed primer of approved brand and manufacture on wood work.

painting with synthetic enamel paint of approved brand and manufacture to give an even shade- 2 or more coats

With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/steel works.

Applying 2 coats of synthetic enamel point of approved shade & make over steel surface - do-

Providing average 115mm thick lime terracing (24 lime 36 surkhi:100 brick khoa) well beaten and compacted including maintaining proper level and slope making gundi with finishing

Providing gola 75 x 75 mm in cement concrete 1:2;4 ( 1 cement : 2 coarse sand : 4 stone aggregate 10 mm and down gauge) including finishing with cement mortar 1 : 3 ( 1 cement : 3 fine sand) as per standard design :

Providing and laying water proofing treatment on roof slab in two component factory designed ready to use

Making khurras 45 x 45 cm with avg. minimum thickness of 5 cm cement concrete 1 : 2 : 4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over PVC sheet 1 mm

Providing and fixing white vitreous china type water closet pedestal (Eurpean type WC pan) with seat & lid CP brass hinges & rubber bufflers 12.5 Itr high level C.I flushing cistern with fitting RS or Cl brackets galvanised steel telescopic flush pipe with fittings & clamps 20 GI overflow pipe with specials & mosquito proof couping of approved muicipal design & GI chain & pull complete including painting of cistern & fittings and brackets cutting and making good the walls and floors wherever required WC pan with ISI marked white solid plastic seat and lid.

Providing and fixing white vitreous flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required: One Urinal basin with 5 litre white P.V.c automatic flushing cistern

Providing and fixing white vitreous china wash basin with C.I./M.S brackets 15 mm CP brass pillar taps 32 mm CP brass waste of standard pattern including painting of fittings and brackets cutting and making good the walls wherever required White vitreous wash basin size 550x450 mm with a single 15 mm CP pillar taps

Providing and fixing Stainless steel A ISI 304(18/8) Kitchen sink as per IS:13983 with CI Brackets and stainless steel plugs 40mm including painting of fittings and brackets cutting & making good the walls where ever required : Kitchen sink with drainboard 510 x 1040mm with bowl depth 250mm

Providing and fixing PVC waste pipe for sink or wash basin including PVC waste fittings complete. Semi rigid pipe 32 mm dia

Providing and fixing PTMT bottle trap for wash basin & Sink. Bottle trap 31mm single piece moulded with height of 270mm, effective length of tall pipe 260mm from the centre of the waste coupling, 77mm breadth with 25mm minimum water seal, weighing not less than 260 gms.

Providing and fixing 100 mm sand cast iron grating for gully trap

Providing and fixing mirror of suprerior glass (of approved quality) and of required shape and size with plastic moulded frame approved make and shade with 6mm thk. Hard board backing: Rectangular shape 1500x450 mm

Providing and fixing PTMT towel Rail complete with brackets fixed to wooden cleats with CP Brass screws with concealed fittings arrangement of approved quality and colour. 450mm long towel rail with total length og 495mm, 78mm wide and effective height of 88mm, weighing not less than 170 gms.

Providing and fixing toilet paper holder: C.P Brass

Providing and fixing CP Brass 32mm size bottle trap of approved quality and make and as per the direction of E/I.

Providing and fixing soil waste and vent pipes: 100 mm dia Centrifugally cast (spun) iron S & S pipe

Providing and fixing MS holder-bat clamps of approved design to Sand cast iron/ cast iron (spun) pipe embedded in and including cement concrete blocks 10 x 10 x 10 cm of 1:2:4 mix (1 cement 2coarse sand 4 graded stone aggregate 20 mm nominal size) including cost of cutting holes and making good the walls etc. For 100 mm dia pipe.

Providing and fixing bend of required degree with access door insertion rubber washer 3 mm thick bolts and nuts complete. Sand Cast iron S&S as per IS- 3989.

Providing and fixing plain bend of required degree. 100 mm Sand Cast iron S&S as per IS- 3989

Providing and fixing collar: 100 mm Sand Cast iron S&S as per IS- 3989

Providing lead caulked joints to sand cast iron /Centrifugally cast (spun) iron pipes and fittings of diameter 100mm

Providing and fixing sand cast iron trap of self cleansing design with sand cast iron screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors : 100 mm inlet and 100 mm outlet- sand Cast (spun) iron S&S as per IS:3989

Painting sand cast iron / centrifugally cast (spun) iron soil, waste vent pipes and fittings with paint of any colour such as chocolate grey, or buff etc. over a coat of primer (of approved quality) for new work : 100 mm diameter pipe

Providing and fixing GI pipes complete with GI fittings and clamps, including cutting and making good the walls etc. (internal work) Exposed on wall 15 mm dia nominal bore

20 mm dia nominal bore

25 mm dia nominal bore

Concealed pipe including painting with anti-corrosive bitumastic paint, cutting chases and making good the wall 15 mm dia nominal bore

20 mm dia nominal bore

Providing and fixing brass gate valve with CI wheel of approved quality (screwed end) 25 mm nominal bore

Providing and fixing ball valve (brass) of approvedquality complete High or low perssure with plastic floats 15 mm nominal bore

Painting GI pipes and fittings with two coats of anti- corrosive bitumastic paint of approved quality. 15 mm dia nominal bore

20 mm dia nominal bore

25 mm dia nominal bore

Providing and fixing GI union in GI pipe including cutting and threading the pipe and making long screws etc. complete (new work) 15 mm nominal bore

20 mm nominal bore

25 mm nominal bore

Providing and placing on terrace ( at all floor levels ) polyethylene water storage tank of approved brand and manufacture with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Providing and fixing CP brass bib cock of approved quality conforming to IS & weighing not less than 690 gms. 15 mm Nominal bore

Providing and fixing CP brass stop cock (concealed) of standard design and of approved make conforming to IS : 8931 15 mm Nominal bore

Providing and fixing CP brass angle valve for basin mixer and gyser points of approved quality conforming to IS : 8931 15 mm Nominal bore

Providing and fixing PVC Connection pipe with brass union: 30 cm length, 15mm nominal bore

Providing and fixing square-mouth SW gully trap grade 'A' complete with CI grating brick masonry chamber with bricks of class designation 75 and water tight CI cover with frame of 300 x 300 mm size (inside) the weight to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5: With FPS bricks

Construction of brick masnory manhole in cement mortar 1:4(1cement :4 coarse sand) RCC top slab with 1:2:4(1cement :2coarse sand :4 grade stone aggegrate 20mm nominal size )foundation concrete 1:4:8mix(1cement :4 coarse sand :8 grade stone aggegrate 40mm nominal size)inside plastering 12mm thk with cement mortar 1:3 (1cemnt :3 coarse sand )finished with floating coat of neat cement and making channels in cement concrete 1:2:4(1cement 2 coarse sand : 4graded stone aggegrate 20mm nominal size )finished with a floating coat of neat cement . Inside size 90x80cm and 45cm deep including CI cover with frame (light duty )455x610mm internal dimension total weight of cover and frame to be not less than 38kg (weight of cover 23kg and weight of frame 15kg.) With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS: 13592 Type- A, including jointing with seal ring conforing to IS:5382, leaving 10mm gap for thermal expansion, (i) Single Socketed pipes. 110 mm diameter

Providing and fixing MS holder bat clamps of approved design to CI or SCI rain water pipes embedded in and including cement concrete blocks 10x10x10 cm of 1:2:4 mix (1 cement :2 coarse sand:4 graded stone aggregate 20 mm nominal size) and cost of cutting holes and making good the walls etc. 100 mm diameter

Providing and fixing on wall face unplasticised-PVC moulded fittings/accessories for unplasticised Rigid PVC rain water pipes conforming to IS:13592 Type- A, including jointing with seal ring conforming to IS:5382, leaving 10mm gap for thermal expansion. 110 mm diameter bend

Providing lead caulked joints to sand cast iron rain water pipes and fittings: 100 mm dia pipe

Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diametre and weighing not less than 440 grams.

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed steel conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. Group B

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed steel conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required. 2 X 4.0 sq. mm + 1 X 4.0 sq. mm earth wire

Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required. 2 Pair

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required.

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 25 mm

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. Telephone socket outlet

TV antenna socket outlet

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. 1 or 2 Module (78mmX78mmX45mm)

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required.

Erection on incandescent light fittings: Erection of wall bracket/ceiling fittings of all sizes and shapes containing upto two GLS lamps per fitting complete with all accessories including connection etc as required.

Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable, including providing and fixing phenolic laminated sheet cover on the fan box etc. as required.

Installation of exhaust fan upto 450 mm sweep in the existing opening, including making the hole to suit the size of the above fan, making good the damage, connection, testing, commissioning etc. as required. Upto 450 mm sweep

Extra for fixing the louvers/ shutters complete with frame for a exhaust fan of all sizes.

Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point (without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed steel conduit, and earthing the point with 1.5 sq. mm FRLS PVC copper conductor single core cable etc. as required. insulated. Group B

Supplying & fixing suitable size GI box wih modular plate and cover in front on surface or in recess including providing and fixing 25 A modular socket outlet and 25 A modular SP MCB, "C" curve including connections, painting etc. as required.

Supplying and fixing PVC batten/ angle holder including connections etc. as required.

Supplying, installation, testing & commissioning of following size ceiling fan 3 blades confirming to IS: 374:2019 including wiring the down rods of standard length upto 30cm with 1.5 sqmm FR PVC insulated copper wire suitable for 230V 50Hz single phase supply etc complete as required. 1200mm 48" BLDC 5 star rating 32W Ceiling fan.

Supplying and fixing following way surface/ recess mounting, vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCB's (but without MCBs & incomer) as required. (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required) 8 way (8 + 24), Double door, vertical type

Supplying and fixing 6 A to 32 A rating, 240V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. 6/32 amps, Single Pole

6/32 amps Triple pole and neutral

Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required.

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm)

Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe from earth electrode including connection with G.I. nut, bolt, spring, washer excavation and re-filling etc. as required.

Laying of one number additional PVC insulated and PVC sheathed/ XLPE power cable of 1.1 KV grade of following size exceeding 35 sq mm but not eceeding 95sq mm in the existing RCC/ HUME/ METAL pipe as required.

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3½ X 120 sq. mm (45mm)

4 X 16 sq. mm (28mm)

CEMENT [ LEAD 20KM ]

STEEL [ LEAD 20 KM ]

SAND [ LEAD 49 KM (48P+1K) ]

STONE CHIPS [ LEAD 53 KM (52P+1K) ]

STONE METAL [ LEAD 53 KM (52P+1K) ]

BRICKS [ LEAD 16 KM (15P+1K) ]

Labour cess @ 1%

Please Enable Macros to View BoQ information