REPAIRS AND CLEANING OF SEWAGE LINE, MAN HOLES, SEPTIC TANKS, SOAK PITS, AT C2A AND C2B AREA AND REPAIR TO ROOF, CEILING, FLOORING, PLINTH PROTECTION, BRICK WORK AND PLASTERING IN C1 AND C1A AREA UNDER GE (EAST), MATHURA

Amount

Cleaning of sewage lines which are blocked /filled with sludge, semi solid/material etc by roding manholes to manholes manuually or by sewage line/manholes. Manhole covers and removing the sludge to a non inhabitant area or buried into ground all as specififed for the follwoing internal dia of pipe. Note :- (i) Sewage line cleaned should function smoothly during entire contract period and measurement shall be made only once. (ii) Contractor shall be responsible to clear any further blocagkage without any extra payment till completion of work.

150 mm dia

200 mm dia

Cleaning and de-sludging water/ liquid/semi solid sludge in foul position from septic tanks and soak wells of any size depth or width by mechanically with pump and filling in the covered tank mounted on truck (Honey Sucker) and disposing of the same out side of MOD land complete all as specified.

S&F in repair 75 mm dia of outlet cast iron Nahani trap.

S&F in repair Salt glazed stoneware gully trap round mouthed, type 'P' 150 x 150 mm size.

S&F in repairs 110 mm dia PVC (SWR) pipe type A single socketed in any length with rubber ring jointed fixed to wall incl necessary clamp etc or laid in trenches or in floors.

S&F in repairs 75 mm dia PVC (SWR) pipe type A single socketed in any length with rubber ring jointed fixed to wall incl necessary clamp etc or laid in trenches or in floors.

S&F PVC (SWR), junction single, (Single T) equal or unequal with acess door 110 mm bore.

S&F PVC (SWR) bends any radius 75mm bore.

S&F PVC (SWR), junction single, (Single T) equal or unequal with acess door 75 mm bore.

Excavating in trenches n exc 1.5 m wide and n exc 1.5 m in depth, for foundation, etc. and getting out in soft/ loose soil.

Excavating in trenches n.exc 1.5 m wide exc 1.5 m and n exc 3m in depth, for foundation, etc. and getting out in soft/ loose soil.

Demolition and breaking up drain pipes (salt glazed ware, AC or reinforced concrete) set in cement motar including cement concrete bedding and haunching complete all as specified and as directed 100mm int dia of pipe.

Demolition and breaking up drain pipes (salt glazed ware, AC or reinforced concrete) set in cement motar including cement concrete bedding and haunching complete all as specified and as directed 150mm int dia of pipe.

Demolition and breaking up drain pipes (salt glazed ware, AC or reinforced concrete) set in cement motar including cement concrete bedding and haunching complete all as specified and as directed 200mm int dia of pipe.

M&L for PCC M-10 grade (Nominal mix) using 40 mm graded stone agregate in bed to drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested for 100 mm int dia of pipe.

M&L for PCC M-10 grade (Nominal mix) using 40 mm graded stone agregate in bed to drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested for 150 mm int dia of pipe.

M&L for PCC M-10 grade (Nominal mix) using 40 mm graded stone agregate in bed to drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested for 200 mm int dia of pipe.

M&L for Salt glazed stoneware drain pipes, grade `A` of 100mm internal dia laid in trenches and jointed in cement mortar 1:1 all as specified and as directed.

M&L for Salt glazed stoneware drain pipes, grade `A` of 150mm internal dia laid in trenches and jointed in cement mortar 1:1 all as specified and as directed.

M&L for Salt glazed stoneware drain pipes, grade `A` of 200mm internal dia laid in trenches and jointed in cement mortar 1:1 all as specified and as directed.

Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section ) cement concrete 1:2:4 type B-1 smooth finished and reforming benching as required for 150 mm int dia of pipe.

S&F Cast iron work grade FG 150, unmachined, in gully traps, gratings, manhole covers and similar articles.

Demolition of cement concrete in ground floors and pavings n exc 15 cm thick (above or below ground level) complete all as specified

Demolition of plain cement concrete of any description and in any position.

Demolition of RCC as in cover slabs/ roof slabs (cutting the re-inforcement to facilate demolition) of any description.

Demolition of brick work or stone boulder masonary built in cement mortar including all quoins arches pillars etc. but excluding ashlar facing dressed stone work and precast concrete articles

M & L for PCC M-10 grade (Nominal mix) using 40 mm graded stone agregate an in foundation of manholes etc complete.

M&L for brick work with old size fly ash bricks straight or curved on plan exc 6m mean radius built in CM 1:4 complete all as specified and as directed.

M&L for PCC M-15 grade (Nominal Mix) using 20 mm graded stone aggregate as in coping, benchings etc.

M&L for use & waste of steel form work (rough finished flat) to sides and soffit of roof slab, shelves etc n. exc 200mm thick etc complete all as specified and as directed.

M&L for use & waste of steel form work (rough finished flat) to edges of concrete flat, roof slabs n.exc 200mm thick, shelves etc complete all as specified and as directed

M&L for TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips.

M&L for TMT bars 8 to 10 mm dia cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips.

M&L for MS bars 10mm dia, cut to length, bent to shape required as in handle of manhole cover.

M&L for Precast RCC M-25 grade (Design mix) as in cover slabs for manholes etc.

M&L for RCC M-25 grade (Design mix) as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like & similar RCC works all as specified and directed

M&L for providing precast cement concrete M-15 grade (Nominal Mix) )using 12.5 mm graded stone aggregate as in louvers and jallies 40mm thick including all mouldings set in CM 1:4.

Taking down cement plaster on brick or stone masonry wall etc incl racking out joints hacking for key , scrubbing down with water etc as in internal and external surfaces of man holes , septic tank, filter bed etc including removing debris off the premises.

M&L for 15 mm thick plastering in CM 1:4 on fair faces of brick work or concrete surfaces and finishing the surfaces even & smooth without using extra cement all as specified and as directed.

M&L for 15 mm thick plastering in CM 1:4 on other than fair faces of brick work surfaces and finishing the surfaces even & smooth without using extra cement all as specified and as directed.

Dismantling of mild steel work of any description not other wise provided for.

Dismantling structural steel work including doors, gates but excluding framed truss etc.

Taking down steel gate by dismantling of pintol hinges replacing by new hinges of MS angle 50x50x6 mm 450 mm long and 16 mm dia MS round 100 mm long pin by welding and fixing with PCC bed block of 200 x 200 x 400mm size and making good including one coat of synthetic enamel paint etc. complete all as specified and as directed by Engineer-in-Charge.

S & F hot rolled medium and high tensile structural steel of grade E 250 quality C conforming to IS 2062: 2011 as in framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as specified and as directed.

S & F hot rolled low tensile structural steel of grade E165 as per IS 15911: 2010 as in hand rails, half round or other stock section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embedding in concrete and screwing etc. Wind ties for roof including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar works complete all as specified and as directed.

S & F hot rolled medium and high tensile structural steel of grade E165 as per IS 15911: 2010 as in framed work such as grills, grating, etc., with ends of bars of shouldered and/or riveted, or forged into spikes, framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework water tanks and similar work complete all as specified and directed by Engineer-in-charge.

Dismantling fencing wire mesh, any type.

Supply only chain link MS galvanised fencing any size or type.

Fixing only chain link fencing including line wire mesh, size and type to any type of standards, rails, straining bolts etc including provision of binding wire.

M&L for PCC M-15 grade (Nominal Mix) using 20mm graded stone aggregate as in Surface channels and drains etc complete all as specified and directed.

M&L for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, mounds, mitred/stopped end etc.

All as per item No 51 above but add or deduct for each 25 mm girth or part thereof over or under 30 cm ditto.

Dismantling galvanised 2 strand, steel barbed wire in fencing.

S&F Galvanised 2 strand steel barbed wire 2.24mm dia barbed with 2mm barbs at 75mm spacing all as specified.

Restraining and resecuring including making good staples etc Galvanised 2 strand steel barbed wire 2.24mm dia barbed with 2mm barbs at 75mm spacing all as specified.

Surface excavation n.exc 30cm deep and averaging 15 deep and getting out in hard/dense soil as in hard core etc.

M&L for hardcore of broken stone or boulder gauge n.exc 63mm, depostited, spread and levelled in layers n exc 15cm thick watered and rammed to true surface.

M&L for 100 mm thick PCC M-7.5 grade (Nominal Mix)using 40mm graded aggregate as in sub based to floor.

M&L for Chequred Cement concrete coloured tiles glossy finish, rubber moulded with grey cement and pigments 30cm x 30cm x 25mm thick, machine pressed, set jointed and pointed in neat cement slurry in floors, with and including 20 mm thick screed bed in CM 1:4 all as specified and as directed.

S&F Machine pressed precast concrete interlocking paver block with grey cement and pigments of any shape and size confirming to IS 15658-2006 of 80mm thick, M-40 Grade laid over 25mm thick sand cushioning Note:-sand filling shall be measured and paid separately under Item No 61.

M&L sand filling under floors including consolidation complete for receiving paver blocks.

M&L for non skid coloured cermic ENDURA tiles exc 0.06 Sqm but n. exc 0.11 Sqm 10 mm thick set and jointed in neat cement slurry & pointed with colured cement to match in floor over and including 15mm thick screed bed in CM 1:4.

M&L for100mm thick PCC M-15 grade (Nominal Mix) using 20mm graded stone aggregate as in floor/hard standing complete all as specified and directed by Engr-in-Charge.

M&L for Preparing new steel surface of any description over 10cm in width or girth and applying two coats of synthetic enamel pain over a coat of red oxide primer.

M&L for preparation of newly plastered surfaces of wall and applying two coats of cement base paint including scaffolding, trestles, ladders, cradles and necessary safety measures complete all as specified and as directed.

Returning, filling in including spreading, leveling, watering and well ramming in layers not exc 25 cm thick using excavated soil all complete all as directed.

Removing of excavated surplus materials to a distance exc 50 m but nexc 100 mm and depositing where directed a level n.exc 1.5 mtrs above the starting point complete all as specificed

Cleaning of blockage of any type of WC (Indian/pedestal) from WC pan to 1st manhole in single/double storied bldg including resetting/refitting of asccess door in soil pipe where open without causing any damage to the wc pan 'P' or 'S' trap and pipe including fitting complete all as speciffied

M&L for cleaning the blockage of bathroom/ kitchen by cleaning the Nahani trags/ gully traps of all the mud/sludge and getting out, washing thoroughly grating of trap, CI waste pipes by opening the cleaning eyes and depositing the sludge in a pit of suitable size at a distance not exceeding 50 metres from the gully trap and covering the same with the soil obtained from excavated of pit including all excavations and earthwork complete all as specified and directed by Engr-in-charge. Note:- The unit rate quoted is deemed to include for keeping particulars bathroom/kitchen undertaken once for cleaning function for entire contract period.

Dismantling Asbestos cement (corrugated, semi corrugated, etc.) sheets in roof coverings

S&F Pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as per IS 15965: 2012 in roof covering, fixed with self tapping screws as specified.

S&F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as per IS 15965: 2012 in cladding to wall fixed with self tapping screws complete.

S&F 2.00 mm Fibre glass reinforced translucent corrugated sheeting with two corrugations side lap fixed with coach screw and washer in roof, wall etc.

Dismantling boarding, any description, fixed in any position complete all as specified and directed.

Providing and fixing inter locking metal grid (snap grid for false ceiling) of size 605 mm x 605 mm in true horizontal level, hot dipped galvanized steel sections (galvanized @ 120 grams/sqm, both side inclusive) consisting of main “T” runner with suitably spaced joints to get required length and of size 24 mm X 38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross “T” of size 24 mm X 28 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main “T” at 600 mm center to center to form a grid of 1200 mm x 600 mm and secondary cross “T” of length 600 mm and size 24 mm X 28 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200 mm X 600 mm panel to form grids of 600 mm X 600 mm and wall angle of size 24 mm X 24 mm X 0.4 mm. Main “T” runners to be suspended from ceiling using GI slotted cleats of size 27 mm X 37 mm X 25 mm X 1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 mm X 30 mm X 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications and as directed by Engineer-in-charge.

M&L for 4 mm thick designer non-asbestos fibre cement building board having fire resistance & moisture resistance properly. Make :- Everest, fixed on aluminium grid with screws complete all as specified and directed.

Dismantling timber scantlings 40 sq. cm and over in section, in any position

Dismantling old unserviceable wrought iron or mild steel work of any description all as specified.

S&F Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. confirming to Fe-410-W.

M&L for providing cement concrete M-15 grade (Nominal mix) using 12.5 mm graded stone aggregate as in roof kerbs or mud stops, rounded or chamfered on edges

Taking down existing roof treatment any description and any thickness including mud phuska, cement concrete tiles all as specified.

M&L for preparing cement concrete surface, providing 10 mm thick modified plaster in CM 1:4, cement mixed with polymer in ratio of 1:10 (1 part of polymer and 10 parts of cement), applying primer coat of epoxy primer with resin and hardener with water dilution as per manufactirer instructions, applying two coats of polyurethane liquid membrane each coat not less than 500 micron thick UV stable having SRI value equal or greater than 105 with consumption of 0.61 Kg/ Sqm (each coat), 2nd coat should be applied once 1st coat is fully dried. Note : Make of material is Asian paints, Thermax or equivalent as approved.

M&L for 40 mm thick avg thickness PCC M-15 grade (Nominal mix) using 12.5 mm graded aggregate as in padding finishing the surface even and smooth without using extra cement.

Taking down cement or cement lime plaster on brick or stone walls, etc. including raking out joints,hacking for key, scrubbing down with water, etc.

M&L rendering 15mm thick (10mm + 5mm) plaster on fair face of brick work in CM 1:4 and surface finished even and fair by mixing liquid water proofing compound as per manufacturers instructions complete. Note :- WPC shall be measured & paid seprately under relevant item of this BOQ.

Supply only liquid water proofing compound hydroseal-W+ or eqivalent (for plaster hardening, to contol efflorescence & fungal growth) as approved by GE.

M&L for preparation of newly plastered surfaces of wall and applying two coats of cement base paint including scaffolding, trestles, ladders, cradles and necessary safety measures complete all as specified and as directed.

M&L for providing damp proof layer in two coats of acrylic polymer coating consisting of 1 part of acrylic polymer liquid mixed with 2 parts of cementious powder applying at the rate of 1.40 Sqm/ Kg of mix per coat. Second coat should be applied after 4-6 hrs of first coat, 5 days curing is to be carried out to the surface before providing plastering. Note :- Make of the material 'Smart Care damp block 2K' of Asian paints or equivalent from Dr Fixit, STP, CICA etc. as approved.

Dismantling water tanks exc 500 ltrs and n exc 1000 Litres complete all as specified and as directed.

S&F 750 litre capacity triple layer ISI Marked rotational moulded polyethylene water storage tank (cylindrical vertical with closed top)hoisted and fixed in position including making inlet/oulet connection and fitting tank connection complete all as specified and as directed.

Supply and Fix 20 mm bore dia Ball valves high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed.

Taking up or down 20 mm bore of dia steel tubing and connections, including cleaning for refixing or removal to store.

Supplying & fixing to walls and ceiling 20 mm nominal bore, medium grade, galvanised coated steel tube conforming to IS 1239 (Part-1): 2004 including all fittings conforming to IS 1239 (Part-2): 2011 complete all as specified and as directed.

M&L for preparation of old plastered surface and applying one coat of cement base paint complete all as specified and directed.

M/S SHRI RAM INFRASTRUCTURE

Karman Infra Projects

BHARDWAJ CONSTRUCTIONS

M/s Kartar Singh Construction Co.

M/s Hoti Lal Contractor

R N AGRAWAL